Design and experiments for the waveguide to coaxial cable adapter of a cavity beam position monitor

The waveguide to coaxial cable adapter is very important to the cavity beam position monitor(CBPM)because it determines how much of the energy in the cavity could be coupled outside.In this paper,the waveguide to coaxial cable adapter of a CBPM is designed and experiments are conducted.The curve shapes of experiments and simulations are very similar and the difference in reflection is less than 0.1.This progress provides a reliable method for designing the adapter.     

Artificial Neural Network Models for Coaxial to Waveguide Adapters

Artificial neural networks provide fast and accurate models for the modeling, simulation, and optimization of microwave and millimeter wave components. In this paper, a multilayer perceptron neural network (MLPNN) is used to model a millimeter wave coaxial to waveguide adapter. The MLPNN is electromagnetically developed with a set of training data that are produced by the full-wave finite-difference time-domain (FDTD) method. One type of the designs of experiments, the central composite technique, is used to allow for a minimum number of FDTD simulations that is needed to be performed. The MLPNN models are useful for the CAD of wideband coaxial to waveguide adapter.     

Full-Wave Analyses of Coaxial to Waveguide Adapters by the FDTD Method

The finite-difference time-domain (FDTD) method is applied to the full-wave analyses of the electrical properties of millimeter wave coaxial to waveguide adapters. The results are useful for the design of wideband coaxial to waveguide adapter.     

Simulation and experiments for the Qext of a cavity beam position monitor

The external Q （Qext） of the dipole mode is a key parameter of the Cavity Beam Position Monitor （CBPM）. It determines the amplitude and length of the dipole mode signal. In this paper, Qext of a CBPM whose waveguides were open to the air was simulated and measured, and the results agreed with each other. Then four waveguide-to-coaxial cable adpaters were adjusted and assembled to the CBPM, and Qext remained unchanged. This progress provides a reliable method to evaluate Qext in the physics design without simulating the structurally complex adapters.     

基于BEPCⅡ的腔式束流位置探测系统设计优化与线下测试

研究了基于BEPCⅡ直线加速器的腔式束流位置探测系统(CBPM)的设计。本方案给出的CBPM探头工作频率为S波段,束流管道半径23 mm,参考腔TM010工作频率和位置腔TM110的工作频率一致。由线下测试结果可知,CBPM实物特征参数与仿真结果一致,CBPM水平和垂直方向工作频率分别为2502 MHz和2503 MHz;垂直和水平的四个端口交叉隔离度均优于-44.7 dB;测量线性区域好于10 mm。射频前端电子学负责对CBPM探头的模拟信号进行滤波、放大和下变频等调制。将CBPM探头置于标定平台,对经过CBPM信号进行时域和频域分析,通过计算得到CBPM水平、垂直方向线下分辨率分别为2.87μm、2.16μm。     

L波段全腔提取轴向输出相对论磁控管设计

设计了一种全腔提取轴向输出相对论磁控管。在模工作的N腔磁控管中, 该结构利用磁耦合的方式通过两个相邻谐振腔在一个扇形波导内激励起TE11模, 然后再由N/2个相位相同的扇形波导TE11模沿轴向向外传输。对L波段全腔提取轴向输出磁控管进行了仿真设计, 在600 kV, 6.3 kA的条件下, 获得1.89 GW微波输出, 功率转换效率50%, 微波频率1.57 GHz。该结构在径向方向上仅增加一个扇形波导厚度, 便于实现相对论磁控管的紧凑、高效设计。     

等效电路计算同轴输出腔TM310模式的间隙阻抗

设计了外Q值较小,工作于高阶横磁TM310模的X波段速调管单间隙同轴输出谐振腔。用微波等效电路理论计算了高阶横磁TM310模情形六个漂移管的等效间隙中心位置,由此计算腔内等效间隙中心到输出波导内横向膜片的等效长度。以MATLAB编程计算得到同轴谐振腔TM310模式加载矩形波导滤波器输出回路的间隙阻抗,其结果与传统冷测模拟法计算结果吻合。验证了等效长度计算方法的正确性,用于圆柱腔基模的传统微波等效电路理论能用于分析同轴谐振腔高阶横磁模式输出回路,且比传统的冷测模拟法及场分析法更为快捷。     

回旋管同轴谐振腔模式的选择

 为了研究回旋管工作模式的选择机理,分析了圆柱波导开放式谐振腔、光滑同轴谐振腔和纵向内开槽同轴谐振腔相应波导的色散特性,进而研究了这些谐振腔内模式竞争的问题。对同轴结构波导色散方程作了相应的数值计算,结果表明,同轴谐振腔利用自身色散曲线与谐振腔内外半径比值的数值关系,能够使在开放式谐振腔内无法工作的高阶模式在其内部稳定工作。最后,以德国卡尔斯鲁厄理工学院(KIT)研制的同轴回旋管为例,进行了相应的分析计算,结果表明纵向内开槽同轴谐振腔相对于光滑同轴谐振腔更适合高阶模式的稳定工作。     

同轴电缆连续波电磁辐照的终端负载响应

为了揭示设备互连电缆在连续波电磁辐照条件下的耦合响应规律,以典型射频同轴电缆为受试对象,将电缆终端连接的设备（系统）等效为负载,通过对其进行连续波电磁辐照效应试验研究,分析了受试电缆长度、终端负载状态等对同轴电缆终端负载响应规律的影响。结果表明:同轴电缆对电磁辐照响应具有选频特性,终端负载响应电压的峰值出现在电缆相对长度为1/2整数倍的频点;同轴电缆受到连续波电磁辐照后,感应皮电流通过转移阻抗转化为芯线与屏蔽层之间的差模感应电压,而这一感应电压源的内阻就是同轴电缆的特性阻抗;同轴电缆终端负载阻值的变化不会对其连续波辐照响应曲线的变化规律产生影响,终端负载与等效感应电压源内阻上的电压响应满足分压原理; 同轴电缆皮电流处于谐振状态时,两波节之间的分布感应电压同向,可等效为一个感应电压源,对同轴电缆终端负载响应起直接作用的电压源是最靠近终端负载的等效感应电压源。     

A Single-Ridged Coaxial Hybrid TE011 Coupler with High Mode Purity

We design a single-ridged coaxial hybrid coupler which excites a TE₀₁₁ mode of high mode content in a cylindrical cavity, resonating at 28.2GHz. The coupler consists of a WR-28 rectangular waveguide, a coaxial TE_n11 cavity, and a cylindrical TE₀₁₁ cavity. Both TE₃₁₁ coaxial cavity and TE₄₁₁ single-ridged coaxial cavity are analyzed to examine the TE₀₁₁ mode purity in the central cavity. Mode purity analysis is performed by a field expansion method using Fourier-Bessel orthonormal basis functions. Numerical calculations predict that the TE₄₁₁ single-ridged coaxial cavity excites the TE₀₁₁ mode with mode purity of 98.6%, which is improved by 3% higher compared with the TE₃₁₁ coaxial cavity. Measurements on the single-ridged coaxial coupler show a resonant frequency at 28.078GHz and ohmic and external Qs of 1560, 473 respectively, which are in good agreement with the simulated results of a 3-D finite element electromagnetic code.     

Support Vector Regression Model for Millimeter Wave Transitions

In this paper, we introduce a new method, support vector regression (SVR) method, to model millimeter wave transitions. SVR is based on the structural risk minimization (SRM) principle, which leads to good generalization ability for regression problem. The SVR model can be electromagnetically developed with a set of training data and testing data which produced by the electromagnetic simulation. Two Ka-band millimeter wave transitions, i.e., waveguide to microstrip transition and coaxial to waveguide adapter, are used as examples to validate the method. Experimental results show that the developed SVR models have a good predictive ability, and they are useful for interactive CAD of millimeter wave transitions.     

脊加载同轴交错圆盘波导的高频特性

提出脊加载同轴交错圆盘波导慢波结构,并用电磁场仿真软件HFSS对其色散特性和耦合阻抗进行了计算,分析了不同结构参数对其高频特性的影响。研究表明:脊加载同轴交错圆盘波导有较好的色散特性,它比非同轴结构的带宽有明显增加,同时可以降低慢波结构的相速,用作行波管慢波结构时可以降低工作电压。脊加载同轴交错圆盘波导是一种全金属结构,散热性能好,损耗低,在毫米波及亚毫米波段的行波管中有较好的应用前景。     

脊峰形同轴波导的工作特性

文中给出了脊峯形同轴波导的各波型的截止频率曲线,与最低波型的功率传输量,还有一个波导的衰耗常数公式,指出了脊峯形同轴波导具有极低的截止频率,可以在很宽的频段内工作。这些是同轴线工作于TEM波型时的特性。     

Simulation and experiments for the Q_(ext) of a cavity beam position monitor

The external Q (Q_(ext)) of the dipole mode is a key parameter of the Cavity Beam Position Monitor (CBPM).It determines the amplitude and length of the dipole mode signal.In this paper,Q_(ext) of a CBPM whose waveguides were open to the air was simulated and measured,and the results agreed with each other.Then four waveguide-to-coaxial cable adpaters were adjusted and assembled to the CBPM,and Q_(ext) remained unchanged.This progress provides a reliable method to evaluate Q_(ext) in the physics design without simulating the structurally complex adapters.     

Numerical Study of Mode Competition in Coaxial Cavity Gyrotrons with Corrugated Insert

A time-dependent self-consistent multimode code which allows to model the interaction between the modes of a coaxial cavity gyrotron operating at the fundamental and/or at higher harmonics of the cyclotron frequency is presented. The Method of Moments (MoM) is used to obtain a rigorous solution of the eigenvalue problem for a coaxial waveguide with corrugated insert. It is shown that the use of the Surface Impedance Model for the calculation of modes operating at higher harmonics leads to incorrect results in high-power coaxial cavity gyrotrons. However, the numerical simulations based on the MoM agree well with the available experimental results.     

Simulation and experiments for the Q_ext of a cavity beam position monitor

The external Q (Qext) of the dipole mode is a key parameter of the Cavity Beam Position Monitor (CBPM). It determines the amplitude and length of the dipole mode signal. In this paper, Qext of a CBPM whose waveguides were open to the air was simulated and measured, and the results agreed with each other. Then four waveguide-to-coaxial cable adpaters were adjusted and assembled to the CBPM, and Qext remained unchanged. This progress provides a reliable method to evaluate Qext in the physics design without si...     

一种耦合度可调节的微波脉冲压缩装置设计及实验

针对有源能量倍增器法(SLED)脉冲压缩实验中对储存能量阶段和释放能量阶段耦合度调节的需求,利用支臂短路波导H-T的调配功能,设计了一种耦合度可调节的SLED脉冲压缩装置。基于散射矩阵理论,分析了支臂短路波导H-T对SLED脉冲压缩装置耦合度的调节能力。利用大功率波导环形器代替3 dB耦合器,进行了基于单储能腔的无源SLED脉冲压缩实验,实验结果表明,支臂短路波导H-T对耦合度的调节能力与理论分析相吻合。     

Spectral Domain Analysis of Coaxial Cavities

Coaxial cavities are used in high power gyrotrons as the beam-wave interaction structure. Much research has been devoted to their mode selective properties. A coaxial cavity lacks a sharp boundary at its open end, so it has some physical features that can only be observed using a spectral model, such as frequency-dependent field profiles and mode overlapping effects. These properties are important since cold tests are usually conducted in the frequency domain. This study applies the incident/reflected wave boundary condition to the wave equation of a weakly irregular coaxial waveguide. The resistivity of the wall is considered in the analysis. Calculations reveal that the fixed-position spectrum yields an uncertain resonant frequency and quality factor. Although the maximum-field spectrum can uniquely determine the properties of the coaxial cavity, the resonant frequency obtained using the maximum-field spectral model is inconsistent with that obtained using the temporal model. The field-energy spectrum explains the low Q nature of the coaxial cavity. Moreover, resonant frequencies evaluated using the field-energy spectrum agree precisely with those evaluated using the temporal model.     

Experimental Study of a Slot Antenna Excited by a TE011 Mode Coaxial Cavity

A slot antenna is developed to excite the high harmonic waveguide mode for generating large-area plasmas. This antenna consists of a TE₀₁₁ mode coaxial cavity with the axial slots positioned on equal interval on the inner wall. The waves radiated from those slots can excite the high harmonic mode in the central area. With the azimuthal symmetric wave field of the TE₀₁₁ mode, the number of the slots can be chosen to match the field pattern of the high harmonic mode. In this report, the dispersion relation of the coaxial waveguide, the coupling scheme and the mode competition of the cavity are studied. A method has been successfully developed to suppress the TE₁₂₁ mode which is the most competing mode to the TE₀₁₁ mode.     

Perforated coaxial exciter of the higher-order mode of a barrel-shaped cavity

We propose to excite a mode with the rotating field structure in an axisymmetric cavity by a coaxial doubly periodic perforated waveguide. The found relationship between the parameters of the system ensures the total energy transfer from the waveguide to the cavity. __________ Translated from Izvestiya Vysshikh Uchebnykh Zavedenii, Radiofizika, Vol. 49, No. 8, pp. 673–679, August 2006.