Application of Millimeter Wave in Verification of Scale Model Measurement for Radar Cross Section

According to the physical optic approximation, a physical scale factor is suggested for scale model measurement of radar cross section (RCS). By this factor, the models of radar targets can be tested at the same frequency as prototype. This is significant for the lack of experimental equipment required or the problem of frequency dependency of radar absorbing materials on the objects. For the purpose of further verification and comparison, millimeter-wave is used to measure the model at the wavelength scaling down proportionally to the prototype. And the measurements of the models are also carried out at microwave band (same working wavelength with prototype). The computed results from models agree well with the data by prototype itself.     

An Improved On-Wafer Measurement Method for PHEMT Modeling for Millimeter Wave Application

An improved on-wafer measurement method by using coaxial calibration instead of on-wafer calibration for PHEMT modeling is proposed in this paper. The advantage is that S-parameters of PHEMT device can be measured on wafer without impedance standard substrate (ISS) after the S-parameters of the microprobes have been determined. Excellent agreement is obtained between on-wafer calibration measurement and coaxial calibration measurements, respectively.     

基于锯齿波偏频的谐振式光纤陀螺标度因数测试

针对转台测试谐振式光纤陀螺标度因数时存在的测试精度受限于转台性能影响的问题,提出一种基于锯齿波等效输入的陀螺标度因数测试方法.通过在相位调制器上叠加锯齿波偏频信号用于模拟角速度输入,分析了实际转台输入和模拟角速度输入下谐振式光纤陀螺闭环传递函数,推导了偏频锯齿波信号参数与实际输入角速度的对应关系,理论证明了其技术可行性.搭建了基于锯齿波偏频的陀螺标度因数测试系统,对研制的陀螺样机进行了标度因数及非线性度测试,基于锯齿波偏频方法测得的陀螺标度因数与实际转台测试结果基本一致,且标度因数非线性度从0.42%优化到0.26%.研究表明基于锯齿波偏频的谐振式光纤陀螺标度因数快速标定测试方法不仅可以精确测得标度因数,还可有效抑制转台振动等环境干扰引入的测量误差.     

17C反应截面测量及有限力程Glauber模型分析

用透射法测量了能量为79AMeV的¹⁷C在¹²C反应靶上的反应截面;利用有限力程Glauber模型对¹⁷C的密度分布进行了分析.由高能区(965AMeV)相互作用截面数据分析认为¹⁷C具有谐振子密度分布,但拟合本实验结果及高能区实验数据发现,¹⁷C的中子密度分布中存在一个尾巴;假设¹⁷C密度为芯核加单粒子密度分布形式,分析认为¹⁷C的价中子主要处于1d5/2?轨道.     

电磁超表面在微波和太赫兹波段雷达散射截面缩减中的应用研究进展

电磁超表面由于其独特的电磁特性为调控电磁波提供了有力工具,合适地设计成编码、随机、相位不连续、完美吸收器等超表面,就能够控制电磁波的散射以及反射特性,实现雷达散射截面的缩减。本文综述了不同的电磁超表面利用漫反射或者吸收等特性实现在微波和太赫兹波段雷达散射截面缩减中的应用。分析表明,编码超表面由不同的数字单元组成,其反射相位差在很宽的频段范围内满足恒定的关系,设计特殊的单元序列使入射的电磁波产生非定向散射,更高bit编码超表面更容易灵活调控电磁波;随机超表面通过调节阵元的尺寸实现宽带移相从而将金属目标特征性强的反射峰打散成一个无规律、杂乱的波,产生漫反射;不连续超表面由于相位不连续可使电磁波发生漫反射或者异常反射;吸收器通过合理设计结构尺寸实现吸收电磁波能量来减小反射。因此电磁超表面在雷达隐身、宽带通讯、成像等方面具有重要的应用前景。最后对电磁超表面在雷达散射截面缩减中应用的发展趋势进行了初步探讨,未来将向着宽带、柔性、大角度等方面发展。     

A Model for Millimeter Wave Attenuation by Atmospheric Gases in China Area

The earth's atmosphere plays an important role in microwave remote sensing and millimeter wave propagation. In this paper, we study the measurements of the attenuation due to atmospheric gases have been made in China, put forward a empirical model for the atmospheric attenuation of millimeter wave in China area.     

Studies on Fast Algorithm for the Scattering of a Large Array of Waveguide-Fed Wide-Slot Antennas in Millimeter Wave Region

We present an effective numerical technique to characterize the scattering of wide-slot antennas fed by waveguides with arbitrary terminations in terms of the method of moment (MoM) and the mixed potential integral equation (MPIE). In particular, the precorrected-fast Fourier transform (P-FFT) eliminates the need to generate and store the usual square impedance matrix andthus leads to speed up the matrix-vector multiplication in the resultant system. This property makes the Rao-Wilton-Glisson (RWG) functions to be useful in simulating electrically large-scale problems. In addition, the scattering from the finite ground surfaces is accounted for in the total scattered field by using the method of equivalent edge currents. The numerical results are presented and compared with both the traditional method of moment results obtained using the entire-domain basis functions and the experimental results, to demonstrate the proposed method to be a good candidate for study on the scattering of arbitrary wide-slot large array.     

Investigation in the far field characteristics of TM polarized Gaussian beam from the vectorial structure

Based on the vectorial structure of electromagnetic beam and the method of stationary phase, the analytical TE and TM terms of TM polarized Gaussian beam, the rigorous solution of Maxwell's equations for a confocal resonator, have been presented in the far field. Then in terms of the vectorial structure, TM polarized Gaussian beam is compared with Gaussian TEM₀₀ mode. The TE term is located at the y-axis, and the TM term the x-axis. At the non-paraxial case, the whole beam spot is elliptical, and the long axis is located at the y-axis. Moreover, the whole beam spot of TM polarized Gaussian beam is smaller than that of Gaussian TEM₀₀ mode. At the paraxial case, the whole beam spot is circular, and TM polarized Gaussian beam reduces to be Gaussian TEM₀₀ mode.     

Analytical vectorial structure of the anomalous hollow beam in the far field

On the basis of the vector angular spectrum representation of the Maxwell equations and the method of stationary phase, the analytical vectorial structure of an anomalous hollow beam in free space is presented. The energy flux distributions of the anomalous hollow beam, its TE and TM terms in the far field are investigated. The analytical results are analyzed with numerical examples.     

Application of SSOR Preconditioning Technique to Method of Lines for Millimeter Wave Scattering

In this paper, symmetric successive overrelaxation (SSOR) preconditioned CG technique are introduced into method of lines (MOL) to further enhance the computational efficiency of this semi-analytic method. Millimeter wave scattering by an infinite plane metallic grating is used as the examples to describe its implementation, whose analysis usually needs fast algorithms because of electrically large dimension. For arbitrary incident wave, Helmholz equation and boundary condition are used to calculate the impedance matrix and then to obtain reduced current-voltage linear matrix equation in spatial domain. An effective symmetric successive overrelaxation preconditioned conjugate gradient iterative method, SSOR-PCG, is chosen to solve this matrix equation. With SSOR as the preconditioner as well as its efficient implementing in CG algorithm, PCG method can converge to accurate solution in much fewer iteration steps.     

75As中子辐射俘获截面的实验测量及蒙特卡罗修正

在四川大学2.5 MV静电加速器上， 用活化法测量了29—1 100 keV 能区中子引起的75As(n， γ)76As反应截面， 并用MCNP 4C程序对实验中由中子的多次散射、 注量率衰减效应等引起的偏差进行了修正， 最后将所得结果与已有数据进行了比较。 We have measured the neutron radiative capture cross section of 75As in the energy range of En=29—1 100 keV using the activation technique at 2.5 MV electrostatic accelerator of Sichuan University. The experimental data were then corrected for multiple scattering and self shielding effects with MCNP 4C code. We also compared our results， with the existing measurement， calculation and evaluated data in ENDF/B Ⅵ.     

三维相位展开算法在精密运动测试中的应用

三维相位展开算法将基于空间的相位展开算法拓展到时间轴上,包含了一维时间和二维空间信息,适合于运动测试。通过建立一维时间相位展开算法的数学模型,分析了该算法运动测试的基本原理,讨论了在精密测试中的使用方法和适用范围,并对微谐振器的微结构进行运动测试。实验表明,算法在相位展开中引入时间信息,不仅消除了形变测量中需选取静止点为相位参考点或参考平面的限制,还可以同时测量物体表面某点纳米级的离面运动曲线和表面形变。     

光纤激光陀螺镜在超短脉冲测量中的应用研究

介绍了采用光纤激光陀螺镜测量超短脉冲宽度、形状、相位时的应用理论．以及相关群速度色散的补偿办法：利用可以自行调节旋转角速度的光纤陀螺镜作为光学延迟线实现旋转角速度的任意连续调整．并在使用归一化的Gerchberg-Saxlon算法中实现过程自动控制、克服了原有测量方法中因时延一定．只能作一次自相关处理．及把时延测量变为路径测量时准确性差和测量精度有限的缺点。利用高精度单光子计数系统对相干光包络进行测量．极大地提高了测量精度．进一步拓宽了超短脉冲在物理、生物、化学以及超高速光纤通信等领域的应用范围.     

Testing a New Class of Phonon Operators for RPA-Like Calculations Within an Exactly Solvable Model

Working in a boson formalism, we introduce a phonon operator different from that commonly used in RPA calculations. As a major feature, this new phonon operator has a vacuum carrying only a limited number of particle-hole excitations. Therefore, the form of this vacuum is quite different from the exponential one of the RPA. In addition, multiphonon excitations have a particle-hole structure never exceeding in complexity that of this vacuum, no matter how large is the number of phonons involved. We present the results of some preliminary tests performed within the exactly solvable two-level Lipkin model.     

投影光刻机硅片调焦调平测量模型

成像质量是光学光刻机的最主要指标,硅片调焦调平测量是光刻机控制成像质量的基础.为此建立了硅片调焦调平测量系统单个测量点的测量模型,并根据硅片形貌标准和集成电路尺寸标准,推导了近似运算规则,简化了曝光场高度与测量光斑在光电探测器上的位置之间的数学关系.运用最小二乘法和平面拟合曝光场曲面的方法,推导了基于多个测量点的曝光场高度和倾斜测量的数学模型.该模型能满足调焦调平实时测量和控制的需要,可用于测量精度优于10 nm的高精度调焦调平测量系统,能满足线宽小于100 nm投影步进扫描光刻机的需要.     

绝对编码光栅的相位细分及其在位移测量中的应用

提出通过光栅条纹相位的精密测量,获取光栅高精度位移信息的方法。具体方法是对光栅图像采用多码道设计,用CCD二维图像传感器获取测量段光栅图像多码道信息。对最低码道图形的周期函数序列进行傅里叶变换、基频滤波和逆傅里叶变换获得光栅截断相位分布,其余码道信息提供相位展开的级次,以此获得测量段光栅的绝对相位分布。用光刻的手段制作了实用的绝对编码光栅,基元码道的尺寸是:27.36μm用于明条纹,27.36μm用于暗条纹,最小基元码道空间周期为54.72μm,光栅长度为14008.32μm。在步长近似3μm的位移测试中,与比对的标准仪器记录值比较,标准偏差为0.2057μm,精度在亚微米量级。重复性实验表明,位置测试的稳定性为0.09μm(标准差),得到600倍以上细分的分辨力。     

涡旋光的干涉特性及其在变形测量中的应用

将涡旋光应用于电子散斑干涉,测量变形物体的离面位移.把传统的电子散斑干涉测量技术与液晶空间光调制器相结合,将所获得的涡旋光作为参考光或者物光进行变形测量.推导出物光为平面光、参考光为涡旋光,和参考光、物光均为涡旋光时物体变形后的干涉强度公式,模拟计算了变形后的干涉图样,分析了变形图样的特征.运用四步相移方法得到了物体的变形相位公式,通过解包裹得到了物体的变形相位.模拟计算得到的三维相位分布图与物体离面位移的变形相位理论值的三维分布图相吻合.模拟实验结果表明,涡旋光可以应用于物体的变形测量,为变形测量提供新的途径.     

CATIA V5环境下基于产品数模的三坐标测量机测点自动采样

为了实现CAD与CAIP(计算机辅助测量规划)的集成,提出了一种基于产品三维模型的CMM(三坐标测量机)测量点采样方法。该方法从产品的IGES文件中有效识别型面形状与边界定义,采用均匀采样与依曲率变化二次采样相结合的策略,针对各个型面类型制定专门的信息处理机制,实现测量点的自动采样,并通过转换在参数平面中判断采样点与裁剪区域的隶属关系,以有效剔除无效采样点;通过典型飞机部件外形曲面的采样点生成结果表明,该方法能有效应用于飞机的测量规划中。     

中能区丰中子核11Li的反应总截面的测量

利用HIRFL提供的50MeV/u的¹³C束流轰击Be靶, 通过RIBLL选择出放射性核素¹¹Li. 实验采用透射法测量了25—45MeV/u的¹¹Li在²⁸Si靶上的反应总截面. 采用双参数Gauss密度分布形式, 利用Glauber模型很好地拟合了高能和中能区的¹¹Li实验数据, 并从密度分布中提取了核的物质均方根半径.     

Electron Impact Ionization Cross Section for Excited State of Ne like Ions in Detailed Configuration

１ＩｎｔｒｏｄｕｃｔｉｏｎＥｌｅｃｔｒｏｎｉｏｎｃｏｌｉｓｉｏｎｉｏｎｉｚａｔｉｏｎｉｓｏｎｅｏｆｔｈｅｍｏｓｔｉｍｐｏｒｔａｎｔｐｒｏｃｅｓｅｓｉｎａｔｏｍｉｃｐｈｙｓｉｃｓ．Ｔｈｅｉｏｎｉｚａｔｉｏｎｃｒｏｓｓｅｃｔｉｏｎｓａｒｅｖｅｒｙｉｍｐ...