High efficiency micellar electrokinetic chromatography of hydrophobic analytes on poly(dimethylsiloxane) microchips

This paper describes a simple method for the effective and rapid separation of hydrophobic molecules on polydimethylsiloxane (PDMS) microfluidic devices using Micellar Electrokinetic Chromatography (MEKC). For these separations the addition of sodium dodecyl sulfate (SDS) served two critical roles - it provided a dynamic coating on the channel wall surfaces and formed a pseudo-stationary chromatographic phase. The SDS coating generated an EOF of 7.1 x 10(-4) cm(2) V(-1) s(-1) (1.6% relative standard deviation (RSD), n = 5), and eliminated the absorption of Rhodamine B into the bulk PDMS. High efficiency separations of Rhodamine B, TAMRA (6-carboxytetramethylrhodamine, succinimidyl ester) labeled amino acids (AA), BODIPY FL CASE (N-(4,4-difluoro-5,7-dimethyl-4-bora-3a,4a-diaza-s-indacene-3-propionyl)cysteic acid, succinimidyl ester) labeled AA's, and AlexaFluor 488 labeled Escherichia coli bacterial homogenates on PDMS chips were performed using this method. Separations of Rhodamine B and TAMRA labeled AA's using 25 mM SDS, 20% acetonitrile, and 10 mM sodium tetraborate generated efficiencies > 100,000 plates (N) or 3.3 x 10(6) N m(-1) in <25 s with run-to-run migration time reproducibilities <1% RSD over 3 h. Microchips with 30 cm long serpentine separation channels were used to separate 17 BODIPY FL CASE labeled AA's yielding efficiencies of up to 837,000 plates or 3.0 x 10(6) N m(-1). Homogenates of E. coli yielded approximately 30 resolved peaks with separation efficiencies of up to 600,000 plates or 2.4 x 10(6) N m(-1) and run-to-run migration time reproducibilities of <1% RSD over 3 h.     

Highly efficient protein separations in capillary electrophoresis using a supported bilayer/diblock copolymer coating

A surfactant/polymer wall coating consisting of the doubly chained cationic surfactant dimethyldioctadecylammonium bromide (DODAB) and polyoxyethylene (POE) 40 stearate is investigated. The coating is formed by simply rinsing a capillary with a solution containing DODAB and POE 40 stearate. The resultant coating is semi-permanent--demonstrating stable electroosmotic flow (EOF) even after a 60 min high pressure rinse with buffer. The EOF (-0.45+/-(0.23) x 10(-4) cm(2) V(-1) s(-1) at pH 7.4) is suppressed by more than a factor of ten compared to that observed for DODAB alone. Model protein mixtures were separated over a pH range of 3-10 with efficiencies of up to greater than 1 million plates/m for the basic proteins cytochrome c, lysozyme, ribonuclease A and alpha-lactalbumin, and the acidic proteins insulin chain A, trypsin inhibitor, and alpha-chymotrypsinogen A. Migration time reproducibility was 0.5-4.0% from run to run and 0.6-4.3% from day to day. Protein recoveries with this coating ranged from 84% to 97%.     

Micellar electrokinetic chromatography at low pH with polyelectrolyte-coated capillaries

The performance of capillaries coated with a poly(diallyldimethylammonium) (PDADMA) monolayer or poly(diallyldimethylammonium)-poly(styrenesulfonate) bilayer was investigated and compared under micellar electrokinetic chromatographic (MEKC) conditions. Both monolayer (positively charged) and bilayer (negatively charged) coatings with micellar (sodium dodecyl sulfate) electrolyte generated very stable and pH-independent cathodal electroosmotic flow (EOF). From the results obtained, it can be concluded that in a doubly coated capillary the second poly(styrenesulfonate) layer is replaced by sodium dodecyl sulfate micelles during flushing with micellar electrolyte. Consequently, in order to obtain a stable and pH-independent cathodal electroosmotic flow for the MEKC separations, the capillary coating with the second polyanion layer is not necessary. The importance of the PDADMA coating was illustrated by comparing MEKC separations of the common developing agents (hydroquinone, phenidone, pyrocatechol, pyrogallol and quinone) on a bare uncoated capillary with the coated capillary. The coating provides reproducible MEKC separations at low pH (pH 3.0) with relative standard deviation (R.S.D.) values for migration times and peak areas lower than 0.45 and 3.3%, respectively. Good linearities in the range from 5 x 10(-5) to 2 x 10(-3) mol l(-1) were obtained for all five compounds, with correlation coefficients higher than 0.998. The detection limits were in the range from 5 x 10(-6) mol l(-1) for pyrocatechol to 2 x 10(-5) mol l(-1) for quinone. The proposed MEKC system was applied to the determination of hydroquinone and phenidone in X-ray photographic developer solutions.     

Mixed cationic/anionic surfactants for semipermanent wall coatings in capillary electrophoresis

Mixtures of the cationic surfactant cetyltrimethylammonium bromide (CTAB) with the anionic surfactant sodium dodecyl sulfate (SDS) form more stable coatings in fused-silica capillaries than CTAB alone. The reversed electroosmotic flow (EOF) generated by CTAB/SDS mixtures remains stable for over 80 min after removal of the surfactants from the buffer. Enhanced stability (relative to CTAB alone) was found even when the ratio of SDS to CTAB was as low as 1%. This greater coating stability is attributed to the structural transition from adsorbed micelle to bilayer, which is induced by addition of SDS. Separation of a mixture of basic proteins yielded efficiencies of 364 000-562 000 plates/m and recoveries ranging from 85% to 98%. Migration time reproducibility was less than 0.9% relative standard deviation (RSD) from run to run and less than 2.6% RSD from day to day.     

Rinse and evaporation coating of poly(methyl methacrylate) microchip for separation of sodium dodecyl sulfate-protein complex

We developed a novel channel wall coating on a poly(methyl methacrylate) (PMMA) microchip using methylcellulose (MC) as a coating reagent to suppress electroosmotic flow (EOF) following the strong analytes adsorption via hydrophobic interaction with channel walls of PMMA. Our coating was obtained by first rinsing channel walls with MC-containing aqueous solution followed by evaporation. The coating made the hydrophilic channel wall lowering EOF by two orders of magnitude (1.2 x 10(-5)cm(2)V(-1)s(-1)) as well as reducing the hydrophobic adsorption. On the coated channel walls, we successfully separated sodium dodecyl sulfate-protein complexes with high reproducibility and efficiency using dextran as a lower viscosity protein separation medium.     

Protein separation and surfactant control of electroosmotic flow in poly(dimethylsiloxane)-coated capillaries and microchips

A thermally pyrolyzed poly(dimethylsiloxane) (PDMS) coating intended to prevent surface adsorption during capillary electrophoretic (CE) [Science 222 (1983) 266] separation of proteins, and to provide a substrate for surfactant adsorption for electroosmotic mobility control was prepared and evaluated. Coating fused-silica capillaries or glass microchip CE devices with a 1% solution of 100 cSt silicone oil in CH2Cl2, followed by forced N2 drying and thermal curing at 400 degrees C for 30 min produced a cross-linked PDMS layer. Addition of 0.01 to 0.02% Brij 35 to a 0.020 M phosphate buffer gave separations of lysozyme, cytochrome c, RNase, and fluorescein-labeled goat anti-human IgG Fab fragment. Respective plates/m typically obtained at 20 kV (740 V cm(-1)) were 2, 1.5, 1.25, and 9.4-10(5). In 50 mM ionic strength phosphate, 0.01% Brij 35 running buffer, the electroosmotic flow observed was about 25% of that in a bare capillary, and showed no pH dependence between pH 6.3-8.2. Addition of sodium dodecylsulfate (SDS) or cetyltrimethylammonium bromide (CTAB) to this running buffer allowed ready control of electroosmotic mobility, mu(eo). Concentrations of SDS between 0.005 to 0.1% resulted in mu(eo) ranging from 3 to 5 x 10(-4) cm2 V(-1) s(-1). Addition of 1 to 2.3 x 10(-4)% (2.7-6.3 microM) CTAB caused flow reversal. CTAB concentrations between 3.5 x 10(-4) and 0.05% (0.0014-1.37 mM) allowed control of mu(eo) between -1 x 10(-4) and -5.0 x 10(-4) cm2 V(-1) s(-1). For both surfactants the added presence of 0.01% Brij 35 provided slowly varying changes in mu(eo) with charged surfactant concentration.     

Separation of serum bilirubin species by micellar electrokinetic chromatography with direct sample injection.

Four major bilirubin species in serum were separated by micellar electrokinetic chromatography with 25 mM sodium dodecyl sulfate (SDS) and 20 mM sodium tetraborate-boric acid buffer at pH 8.5. Due to the solubilization of the serum proteins by the SDS micelles, serum samples were injected directly into a 50 cm x 75 microns I.D. fused-silica capillary and complete separation of the four bilirubin species was accomplished within ca. 10 min without extensive sample pretreatment. Detection was performed by absorbance at 450 nm and average limit of detection was in the 6.0 microM concentration range. The usefulness of this method was demonstrated for the separation and detection of a number of bilirubin species present in pathological human serum samples.     

Use of a microemulsion system to incorporate a lipophilic chiral selector in electrokinetic capillary chromatography

Summary The separation of (1R, 2S) and (1S, 2R)-ephedrine using microemulsion electrokinetic capillary chromatography is reported. The lipophilic chiral selector, (2R, 3R)-di-n-butyl tartrate (0.5% w/w), was introduced into the electrophoretic buffer consisting of 0.6% (w/w) sodium dodecyl sulfate (SDS) and 1.2% (w/w) 1-butanol in 15 mM tris-hydroxyaminomethane buffer (pH 8.1). The two isomers of ephedrine were separated with excellent resolution.     

Application of dodecyldimethyl (2-hydroxy-3-sulfopropyl) ammonium in wall modification for capillary electrophoresis separation of proteins

A zwitterionic surfactant, dodecyldimethyl (2-hydroxy-3-sulfopropyl) ammonium (C12H25N+(CH3)2CH2CHOHCH2SO3-), named dodecyl sulfobetaine (DSB), was used as a novel modifier to coat dynamically capillary walls for capillary electrophoresis separation of basic proteins. The DSB coating suppressed the electroosmotic flow (EOF) in the pH range of 3-12. At high DSB concentration, the EOF was suppressed by more than 8.8 times. The DSB coating also prevented successfully the adsorption of cationic proteins on the capillary wall. Anions, such as Cl-, Br-, I-, SO4(2-), CO3(2-), and ClO4-, could be used as running buffer modifiers to adjust the EOF for better separation of analytes. Using this dynamically coated capillary, a mixture of eight inorganic anions achieved complete separation within 4.2 min with the efficiencies from 24,000 to 1,310,000 plates/m. In the presence of ClO4- as EOF adjustor, the separation of a mixture containing four basic proteins (lysozyme, cytochrome c, alpha-chymotrypsinogen A, and myoglobin) yielded efficiencies of 204,000-896,000 plates/m and recoveries of 88%-98%. Migration time reproducibility of these proteins was less than 0.5% relative standard deviation (RSD) from run to run and less than 3.1% RSD from day to day, showing promising application of this novel modifier in protein separation.     

Application of reverse-flow micellar electrokinetic chromatography for the simultaneous determination of flavonols and terpene trilactones in Ginkgo biloba dosage forms

A reverse-flow micellar electrokinetic chromatographic (RF-MEKC) method was developed for the simultaneous qualitative determination of 10 components consisting of the flavonol glycosides, rutin and quercitrin, the flavonol aglycones, isorhamnetin, kaempferol and quercetin, the terpene trilactones, ginkgolides A, B, C and J and the sesquiterpene, bilobalide. This method was used to fingerprint Ginkgo biloba solid oral dosage forms and validated for the quantitation of the marker compounds, rutin and quercetin in some commercial products. In addition to the usual variables, the influence of some essential background electrolyte (BGE) components such as sodium dodecyl sulphate (SDS) and -cyclodextrin concentrations were investigated. A polyimide fused-silica square capillary column (75 microm I.D. x 360 microm O.D.) with a total length of 60.0 cm and effective length of 45.0 cm was used for the separation. The final BGE consisted of 20 mM phosphoric acid, 40 mM SDS and 12 mM -cyclodextrin (pH 2.2) using reverse polarity with a voltage of -17.5 kV. Samples were injected electrokinetically at -5 kV for 3 s for the qualitative analysis and hydrodynamically at 20 mbar for 0.6 s for the quantitative assay. The total run time was 22 min and the limits of detection were 3.13 microg/ml and 1.88 microg/ml for rutin and quercetin, respectively. Fingerprint profiles of the solid oral dosage forms and the results of the quantitative analysis indicated that there were major discrepancies in the marker content between products and illustrates the value of this method for use as a procedure to assess product quality of commercially available Ginkgo biloba products.     

1,3-dialkylimidazolium-based room-temperature ionic liquids as background electrolyte and coating material in aqueous capillary electrophoresis

The 1-ethyl-3-methylimidazolium (EMIM) cation was found to have constant mobility of 4.5 x 10(-4) cm2 V(-1) s(-1) over the pH range of 3 to 11. The electroosmotic flow of bare silica capillary was reversed by the covalently bonded room-temperature ionic liquid (RTIL) coating. With run buffer of 5 mM EMIM (pH 8.5), NH4+ in human urine was separated from the K+ matrix and was detected to be 0.37 +/- 0.012%. K+, Na+, Li+, Ca2+, Mg2+ and Ba2+ were baseline separated in RTIL-coated capillary with run buffer of 10 mM EMIMOH-acetic acid at pH 5, and the concentration of the above ions in a red wine were detected to be 907, 27.9, 0, 71.0, 83.4 and 31.1 microg/ml, respectively. The RTIL-coated capillary showed stable electroosmotic flow for at least 80 h in the run buffer.     

Capillary electrochromatography using a fluoropolymer as the chromatographic support material

Fused-silica capillary columns were packed with ethylene chlorotrifluoroethylene (ECTFE) particles for use in capillary electrochromatography (CEC). Electroosmotic flow (EOF) was generated in these columns using acetonitrile-water mixtures as the mobile phase. Electroosmotic mobilities of 1.6 x 10(-4) cm2 V(-1) s(-1) (linear velocities of 1 mm s(-1)) were observed using a mobile phase without an electrolyte present. The EOF in the ECTFE-packed columns is enhanced when using trifluoroacetic acid (TFA) as a mobile phase additive; electroosmotic mobilities of 3.65 x 10(-4) cm2 (V-1) s(-1) (linear velocity of 2.5 mm s(-1)) were observed. This enhancement of EOF is attributed to dynamic coating of the ECTFE particles by TFA. Other electrolytes (i.e., Tris/Tris-HCl buffer and H3PO4) in the mobile phase did not have such an enhancement of EOF. However, a slight enhancement of EOF is observed, for example, if small quantities of TFA are added to the mobile phase containing Tris buffer. The potential of ECTFE for CEC is demonstrated by separating a mixture of amino acids.     

Determination of flavour components in natural vanilla extracts and synthetic flavourings by mixed micellar electrokinetic capillary chromatography

The development of a mixed micellar electrokinetic capillary chromatography (MECC) method for the qualitative and quantitative determination of key components, including vanillin, 4-hydroxybenzaldehyde, 4-hydroxybenzoic acid, vanillic acid and 3-methoxybenzaldehyde, that contribute to vanilla flavour was investigated. The micellar phase consisted of sodium dodecyl sulfate (SDS) and sodium cholate (SC). The percent relative standard deviation (R.S.D.%) for migration time was <1 over six runs. The R.S.D.% for peak areas ranged between 0.85-1.96% over six runs. Peak efficiencies were excellent with theoretical plate numbers typically in the range of 130,000-200,000 per column (52 cm effective length). The limits of detection (LOD) were between 5-10 μg/ml. The quantitative data was verified by high performance liquid chromatography (HPLC) and gas chromatography (GC). The mixed MECC method was successfully applied to a number of natural vanilla extracts, nature identical extracts and synthetic flavourings.     

Enhanced stability of surfactant-based semipermanent wall coatings in capillary electrophoresis using oppositely charged surfactant

Semipermanent surfactant coatings are effective for the prevention of wall adsorption of proteins in CE. However, they often suffer from their unsatisfactory coating stability as they essentially degrade from the capillary walls after the surfactants are removed from the buffer. In this paper, we proposed a facile and universal method to improve the stability of semipermanent surfactant coatings based on addition of an oppositely charged surfactant into the coating. Didodecyldimethylammonium bromide (DDAB) and a gemini surfactant, 18-6-18, were used as the model semipermanent coatings, and sodium dodecyl sulfate (SDS) was chosen as their oppositely charged surfactant. SDS can strongly alter the packing parameter P of the cationic surfactants, and consequently mediates the coating stability. With the increase of SDS concentration in coating, the coating stability first dramatically increases due to the enlarged P, and then decreases due to the weakness of electrostatic interaction between the capillary wall and surfactant coating. At the proper SDS concentration, very stable coatings can be obtained that, even after rinsing under 138 kPa for 60 min, the reversed electroosmotic flow (EOF) only decreases by 3.6%. These SDS-enhanced coatings show excellent stability and reproducibility in protein separation (RSD of migration time <1.1% for run-to-run assay, n=9). Also, the high separation efficiency (>500,000 plates/m) and fine recovery of tested proteins indicate that these coatings are powerful in wall adsorption suppression. Finally, we found that the separation efficiency of protein was a more exact indicator for the coating stability than the traditional EOF magnitude.     

Separation of polycyclic aromatic hydrocarbons by micellar electrokinetic chromatography with aqueous short-chain alcohol solvent

Micellar electrokinetic capillary chromatography (MEKC) with aqueous organic solvent has been developed to separate polycyclic aromatic hydrocarbons (PAHs). Methanol, ethanol or propanol as an organic modifier was added to sodium dodecyl sulfate (SDS) micellar solution in order to increase the solubility of very hydrophobic solutes in mobile phase. Both methanol and ethanol can be used as co-solvents for the separation of PAHs. Use of ethanol resulted in a shorter analysis time than use of methanol. The separations of some PAHs were unsatisfactory using propanol although the analysis time was much shorter than with ethanol. The influence of ethanol content, SDS concentration and temperature on the separations was studied. Benzene and nine polycyclic aromatic hydrocarbons were successfully separated using 50 mM SDS-20 mM phosphate-5 mM borate, containing 40% (v/v) ethanol at 35 degrees C. The relative standard deviation (R.S.D.) of t(R) ranged from 0.5 to 1.5% for six repeat injections.     

Analysis of combinatorial chemistry samples by micellar electrokinetic chromatography

A micellar electrokinetic chromatography (MEKC) method has been developed that can evaluate the purity of samples generated in combinatorial chemistry libraries. This method uses an open tube capillary (27 cm x 50 microm) along with a run buffer composed of sodium dodecyl sulfate (SDS), hydroxypropyl-beta-cyclodextrin, and sodium tetraborate coupled with UV detection. Neutral compounds and compounds that were insoluble in aqueous buffers could be analyzed under these conditions in approximately 3 min. The concentration of SDS and the concentration of hydroxypropyl-beta-cyclodextrin effected the separation. The affect on selectivity resulting from the addition of an organic modifier to the run buffer was examined. The low background absorbency of the run buffer made for easy detection of compounds that absorbed at low UV wavelengths. The quick analysis time made this suitable for analysis of combinatorial chemistry samples.     

Proline-coated column for the capillary electrochromatographic separation of amino acids by in-column derivatization

With 3-trimethoxysilylpropyl chloride as the spacer, a proline-coated capillary column was prepared for the capillary electrochromatographic (CEC) separation of amino acids by in-column derivatization. Nine standard mixtures, including aspartic acid, glutamic acid, valine, phenylalanine, alanine, isoleucine, leucine, tyrosine, and tryptophan, were injected. o-Phthalaldehyde (OPA), OPA/2-mercaptoethanol (2-ME) and OPA/N-acetylcysteine (NAC) in borate buffer were tested as the derivatizing agent. Among them, OPA (50 mM) in borate buffer (pH 9.5, 50 mM) gave the best performance. The formation of isoindole could be detected by UV detection. The sandwich-type injection was carried out in hydrostatic mode (10 cm) with the program R(10 s)S(10 s) R(10 s)W(10 min) with R, S, and W being the reagent, sample, and waiting times. Mesityl oxide, benzyl alcohol, and acetone showed some interaction with the column. A current monitoring method was used instead of the determination of the electroosmotic flow (EOF). The direction of EOF was from anode to cathode even under acidic condition lower than the pI value (6.31) of the bonded group due to some unreacted silanol groups. Some parameters including pH, nature, and concentration of the mobile phase and the effect of organic modifier with regard to the CEC separation were investigated. With the proline-coated column (75 (50) cm x 75 microm ID) the best separation was performed in phosphate buffer (pH 4.00, 100 mM) with an applied voltage of -15 kV. The established method was also compared with those precolumn derivatized prior to the separation with proline-coated column as well as with in-capillary derivatization and separation with a bare fused-silica column.     

Comparison of standard capillary and chip separations of sodium dodecylsulfate-protein complexes

Conditions for converting a set of five standard proteins to electrochemically active sodium dodecylsulfate (SDS) complexes were worked out with the aim of using such complexes for conductivity detection with a a chip electrophoresis system. The results obtained were compared with standard capillary electrophoresis (37 cm (effective length 30 cm)×75 μm I.D. capillary, 10 kV, negative polarity at the inlet). The chip separations were run at 500 V per chip (100 V/cm) as compared to the standard capillary arrangement, which was run at 266.6 V/cm. For the capillary set-up the protein complexes were prepared in aqueous solution (Milli-Q water) made 10 mM with respect to SDS. If the SDS concentration was increased to 50 mM, the separation in the capillary was incomplete. On the other hand with the chip system both approaches yielded acceptable results. The chip separations were slightly (but not distinctly) shorter and offered better separations than the standard set-up. The concentration of the surfactant used for the preparation the complexes results in alternations of the elution sequence, which is preserved if the chip separation is used instead of the capillary set-up. Apparently the full capacity of protein–SDS binding is not exploited for the preparation of the adducts.     

Separation of related opiate compounds using capillary electrochromatography

Capillary electrophoretic separations have been investigated for six controlled narcotic analgesic compounds having related structures. Owing to the similar charge-to-mass ratios of these compounds, capillary zone electrophoresis failed to provide a satisfactory separation, whereas a baseline-resolved separation was achieved in 10 min using micellar electrokinetic chromatography. Column efficiencies of 40,000-150,000 plates/m were obtained with a 50 cm long, 50 microm inner diameter (ID) capillary using 50 mM sodium dodecyl sulfate (SDS) in a 50 mM borate solution containing 12% isopropanol. In contrast, separation of this mixture by capillary electrochromatography proved to be significantly superior. The capillary was 15 cm long, with an ID of 75 microm, and was packed with 1.5 microm nonporous octadecyl silica (ODS) particles. The mobile phase consisted of 80% 10 mM tris(hydroxymethyl)aminomethane (Tris) and 20% acetonitrile, and contained 5 mM SDS. A complete separation was obtained in 2.5 min with an efficiency of 250,000-500,000 plates/m.     

Capillaries modified by noncovalent anionic polymer adsorption for capillary zone electrophoresis, micellar electrokinetic capillary chromatography and capillary electrophoresis mass spectrometry

A simple coating procedure for generation of a high and pH-independent electroosmotic flow in capillary zone electrophoresis (CZE) and micellar electrokinetic capillary chromatography (MEKC) is described. The bilayer coating was formed by noncovalent adsorption of the ionic polymers Polybrene and poly(vinylsulfonate) (PVS). A stable dynamic coating was formed when PVS was added to the background electrolyte. Thus, when the PVS concentration in the background electrolyte was optimized for CZE (0.01%), the EOF differed less than 0.3% after 54 runs. The electroosmotic mobility in the coated capillaries was (4.9+/-0.1) x 10(-4) cm2V(-1)s(-1) in a pH-range of 2-10 (ionic strength = 30 mM). When alkaline compounds were used as test substances intracapillary and intercapillary migration time variations (n = 6) were less than 1% relative standard deviation (RSD) and 2% RSD, respectively in the entire pH range. The coating was fairly stable in the presence of sodium dodecyl sulfate, and this made it possible to perform fast MEKC separations at low pH. When neutral compounds were used as test substances, the intracapillary migration time variations (n = 6) were less than 2% RSD in a pH range of 2-9. In addition to fast CZE and MEKC separations at low pH, analysis of the alkaline compounds by CE-MS was also possible.