Indium-organic framework CPP-3（In） derived Ag/In2O3 porous hexagonal tubes for H2S detection at low temperature

There is a great demand for high-performance hydrogen sulfide（H₂S） sensors with low operating temperatures. Ag/In₂O₃ hexagonal tubes with different proportions were prepared by the calcination of Ag+-impregnated indium-organic frameworks(CPP-3（In）), and the developed sensors exhibit enhanced gassensing performance toward H₂S. Gas sensing measurements indicate that the response of Ag/In₂O₃（2.5 wt%） sensor to 5 ppm H₂S ha...     

Optical constants of HNO3/H2O and H2SO4/HNO3/H2O at low temperatures in the infrared region

The complex index of refraction of liquid HNO3/H2O and H2SO4/HNO3/H2O has been obtained at different temperatures and acid concentrations. FT-IR specular reflectance spectra were obtained for 30, 54, and 64 wt % aqueous HNO3 and for four different H2SO4/HNO3/H2O mixtures in the temperature region from 293 to 183 K. The complex index of refraction was obtained from the reflectance spectra with the Kramers-Kronig transformation. The optical constants of the binary and ternary mixtures vary with the acid concentration and the temperature. The results demonstrate that vibrational bands originating from the sulfate species are more sensitive to changes in temperature than the bands originating from vibrations in the nitrate species; only minor changes in the nitrate vibrational bands are observed as the temperature decreases below 248 K.     

State-to-state rotational transitions in H2+H2 collisions at low temperatures

We present quantum mechanical close-coupling calculations of collisions between two hydrogen molecules over a wide range of energies, extending from the ultracold limit to the superthermal region. The two most recently published potential energy surfaces for the H(2)-H(2) complex, the so-called Diep-Johnson (DJ) [J. Chem. Phys. 112, 4465 (2000); 113, 3480 (2000)] and Boothroyd-Martin-Keogh-Peterson (BMKP) [J. Chem. Phys. 116, 666 (2002)] surfaces, are quantitatively evaluated and compared through the investigation of rotational transitions in H(2)+H(2) collisions within rigid rotor approximation. The BMKP surface is expected to be an improvement, approaching chemical accuracy, over all conformations of the potential energy surface compared to previous calculations of H(2)-H(2) interaction. We found significant differences in rotational excitation/deexcitation cross sections computed on the two surfaces in collisions between two para-H(2) molecules. The discrepancy persists over a large range of energies from the ultracold regime to thermal energies and occurs for several low-lying initial rotational levels. Good agreement is found with experiment B. Mate et al., [J. Chem. Phys. 122, 064313 (2005)] for the lowest rotational excitation process, but only with the use of the DJ potential. Rate coefficients computed with the BMKP potential are an order of magnitude smaller.     

Electrophysical properties of In2O3-and WO3-based gas-sensitive semiconducting films as sensors for unsymmetrical dimethylhydrazine in air

Some n-type semiconductor metal oxide sensors based on WO₃ and In₂O₃ were studied in detecting unsymmetrical dimethylhydrazine (UDMH) vapors. The sensors are highly sensitive to the presence of UDMH vapors in air at concentrations equal to or lower than the MPC. They have short response and relaxation times in detecting UDMH vapors in air. It was found that, when ammonia was present in air in concentrations comparable to those of UDMH, it did not affect the electrophysical properties of the semiconductor sensors.     

NO-NH3-O2 reaction catalyzed by V2O5/AC at low temperatures

The effects of SO₂, V₂O₅ loading and reaction temperature on the activity of activated carbon supported vanadium oxide catalyst have been studied for the reduction of NO with NH₃ at low temperatures (150—250°C). It is found that SO₂ significantly promotes the catalyst activity. Both V₂O₅ loading and reaction temperature are vital to the promoting effect of SO₂. The catalysts with V₂O₅ loadings of 1—5 weight percent have a positive effect on the promotion of SO₂, while the catalysts with V₂O₅ loadings of above 7 weight percent have not such an effect or show a negative effect. At lower temperatures (<180°C) SO₂ poisons the catalyst but at higher temperatures promotes it. The reason of the SO₂ promotion was also discussed; it may results from the formation of SO₄ ^2? on the catalyst surface, which increases the surface acidity and hence the catalytic activity.     

Enhancement of H2 Sensing Properties of In2O3-based Gas Sensor by Chemical Modification with SiO2

The sensitivity and selectivity to H2 of a new In203-based gas sensor were improved significantly by surface chemical modification. A dense layer of SiO2 near the surface of the porous In2O3 bead was formed by chemical vapor deposition (CVD) of diethoxydimethysilane (DEMS). The dense layer functioned as a molecular sieve, thereby the diffusion of gases with large molecular diameters, except for 1-12, was effectively controlled, resulting in a prominent selectivity and high sensitivity for H2. The working mechanism of the sensor was also presented.     

Novel ZnO-Al2O3 composite particles as sorbent for low temperature H2S removal

ZnO-Al₂O₃ composite particles composed of ZnO nanosheets（thickness of 40-80 nm） on alumina particles were prepared by heterogeneous precipitation method using bayerite seed particles.The asprepared composite particles were characterized in terms of crystal structure,morphology,surface area and pore volume.The composite particles were used as sorbent for H₂S adsorption at low temperature, and were compared with pure ZnO sorbent.The composite sorbent showed a greater sulfur adsorption capacity（0.052 g/g） than pure form of ZnO（0.028 g/g）.This significant improvement was mainly attributed to higher surface area,more pore volume and unique morphology in nanoscale,which were also obtained by low cost presented method in this work for synthesis of ZnO sorbent supported on alumina particles.     

H2O2-Na2S2O3反应对pH和反应物起始浓度比的依赖性

在H2O2-Na2S2O3反应体系中，pH值和[H2O2]0/[Na2S2O3]0对反应产物的浓度大小起着关键作用.本文通过考察这两种因素对反应产物的影响，以及对反应机理的模拟，得出了pH值和氧化剂与还原剂浓度比影响反应产物浓度的一般规律.结果表明：pH< 3时，反应主要生成单质硫， 3< pH< 6时， 较为稳定，提高pH和[H2O2]0/[Na2S2O3]0有利于SO42-生成，在中性或弱碱性溶液中S(Ⅳ)(HSO42-或SO32-)物质浓度出现峰值.     

Two Related Porous Thioindates with T3 Clusters, (H2DAH)3In10S18·6H2O and (H2DAH)3In10S18

Two high porous thioindates with 1,6‐diaminohexane (DAH), DAH‐InS‐ 1 and DAH‐InS‐ 2 , were prepared by solvothermal reaction. Though the same T₃ supertetrahedral frameworks were reported, the cations are different. DAH is a non‐cyclic diamine and also an economical reagent for synthesis. Because of the structural difference of the structural directing agents, the dimensions of crystal cells of DAH‐InS‐ 1 and DAH‐InS‐ 2 are elongated and the total volumes for the cation and solvent are 74.6 and 72.1 % (Platon) larger relative to those reported previously. The two compounds were obtained in one reaction system by controlling the reaction time. Their structures are briefly discussed and the correlativity of crystal shape with the parameters of microstructure is discussed.     

Metathetical conversion of Nd2O3 nanoparticles into NdS2 polysulfide nanoparticles at low temperatures using boron sulfides

A new simple metathetical sulfidation method using boron sulfides has been developed to prepare nanoparticles of NdS(2) via conversion of ca. 50-nm-sized nanoparticles of Nd(2)O(3) at 450 degrees C, in which boron and sulfur powders form boron sulfides in situ and evaporate to sulfidize the oxide. The X-ray powder diffraction analysis revealed that the products were purely NdS(2), and the atomic absorption spectrometric analysis confirmed nonexistence of boron in the products after washing with water. The detailed TEM studies showed that the NdS(2) nanoparticles maintained the original size of the oxide particles without fusion during the low-temperature sulfidation process.     

Crystal Structures of Na3PO2S2 · 11H2O and Na3POS3 · 11H2O

Summary.  Single crystals of sodium dithiophosphate undecahydrate (Na₃PO₂S₂ · 11H₂O) and sodium trithiophosphate undecahydrate (Na₃POS₃ · 11H₂O) were grown from aqueous solution. The crystal structures of Na₃PO₂S₂ · 11H₂O (P2₁2₁2₁; a = 1248.1(1), b = 945.2(1), c = 1383.1(1) pm; R ₁ = 0.0202, wR ₂ = 0.0502) and Na₃POS₃ · 11H₂O (Pna2₁; a = 1262.0(2), b = 947.6(2), c = 1431.5(2) pm; R ₁ = 0.0720, wR ₂ = 0.1371) are related to each other in a sense that all constituting units are arranged in similar positions and with similar orientations. The geometries of the anions were determined with high accuracy; thus, the structural parameters of the POS³⁻ ₃ anion were measured for the first time. Received September 25, 2001. Accepted January 21, 2002     

Crossed-beam radical-radical reaction dynamics of O(3P)+C3H3-->H(2S)+C3H2O

The radical-radical oxidation reaction, O(3P)+C3H3 (propargyl)-->H(2S)+C3H2O (propynal), was investigated using vacuum-ultraviolet laser-induced fluorescence spectroscopy in a crossed-beam configuration, together with ab initio and statistical calculations. The barrierless addition of O(3P) to C3H3 is calculated to form energy-rich addition complexes on the lowest doublet potential energy surface, which subsequently undergo direct decomposition steps leading to the major reaction products, H+C3H(2)O (propynal). According to the nascent H-atom Doppler-profile analysis, the average translational energy of the products and the fraction of the average transitional energy to the total available energy were determined to be 5.09+/-0.36 kcal/mol and 0.077, respectively. On the basis of a comparison with statistical prior calculations, the reaction mechanism and the significant internal excitation of the polyatomic propynal product can be rationalized in terms of the formation of highly activated, short-lived addition-complex intermediates and the adiabaticity of the excess available energy along the reaction coordinate.     

Investigations of V(2)O(5)-based LPG sensors

Sensor characteristics of V(2)O(5) dispersed on oxide supports such as Al(2)O(3), TiO(2) and ZrO(2) with respect to various gases and vapours including liquefied petroleum gas (LPG) have been investigated. Of all the systems studied, 20 mol% V(2)O(5) dispersed on ZrO(2) shows the highest sensitivity for LPG, the log sensitivity-log concentration (in ppm) plots being linear up to 1000 ppm or more. The sensitivity is not affected by humidity or recycling. Addition of P(2)O(5) to V(2)O(5) however destroys the sensitivity. Considering all aspects, 20 mol% V(2)O(5)/ZrO(2) is suggested for use as a practical LPG sensor. ESR spectroscopy indicates the formation of V(4+) species on exposure of V(2)O(5)/ZrO(2) or TiO(2) to LPG. In-situ high-temperature x-ray diffraction measurements show the formation of an unusual monoclinic form of VO(2) on exposure to LPG at 625 K which gets oxidized back to V(2)O(5) on exposure to air.     

五水硫代硫酸钠非等温脱水过程的确定

通过对五水硫代硫酸钠(Na2S2O3 5H2O)非等温脱水过程的热力学数据进行理论求算和分析,结合两种热分析实验结果,包括差热/热重联机(DTA/TGA)和差示扫描量热(DSC),实验测定结果与理论求算相互验证,确定了五水硫代硫酸钠脱水过程的类型.研究的理论和实验结果表明,Na2S2O3·5H2O的脱水过程是先脱出液态水并形成水溶液,然后随着温度的升高,溶液中水的再气化.     

A pseudopotential study of the hydrogen bond in H2O·H2S,H2S·H2S and H2O·H2Se systems

Intermolecular potential energy curves for the hydrogen bonded systems H₂O·H₂S, H₂O·H₂Se and H₂S·H₂S were calculated with nonempirical pseudopotentials using optimized-in-molecules basis sets augmented by polarization functions. The H₂O·H₂O interaction energy curve has been also considered as a test case. The present results for H₂O·H₂S and H₂S·H₂S indicate much weaker intermolecular interactions than those found in previous ab initio calculations. The H₂O·H₂Se interaction was found to be quite similar to H₂O·H₂S.This work was partly supported by the Polish Academy of Sciences within the Project PAN-09, 7.1.1.1On leave from Quantum Chemistry Laboratory, Dept. of Chemistry, University of Warsaw, Pasteura 1, 02-093. Warsaw, Poland     

In2O3-based multicomponent metal oxide films and their prospects for thermoelectric applications

Thermoelectric properties of In₂O₃–SnO₂-based multi-component metal oxide films formed by spray pyrolysis method are studied. It is shown that the introduction of additional components such as gallium and zinc can control the parameters of the deposited layers. At that, the doping with gallium is more effective for optimization of the efficiency of the thermoelectric conversion. The explanation of the observed changes in the electro-physical and thermoelectric properties of the films at the composition change is given. It is found that the main changes in the properties of multicomponent metal oxide films take place at concentrations of dopants which correspond to their limit solubility in the dominant oxide.     

Solid-state spreading of oxides: Morphology and conductivity of In2O3-based films

Spontaneous solid-state spreading of In₂O₃ over the surface of ceramic and single crystal substrates of Al₂O₃, ZrO₂(0.08Y₂O₃), Y₃Al₅O₁₂ and YAlO₃ at 1380 and 1500 °C has been investigated. The films structure, element and phase composition were studied by means of XRD and SEM/EDS. The phase compositions of all films correspond to that of powder In₂O₃. The most films are dense with monolithic “film/substrate” interface. AC-conductivity in the range 25–250 °C is reported. Depending on the substrate material, the films demonstrate a whole set of conductivity types (semi-conductive, metallic) and wide range of magnitudes (more than 3 orders).Thermodynamic and kinetic aspects of oxide spreading and subsequent crystallization on the surface of primary border film are discussed. It is shown, in particular, that the solid-state spreading is facilitated in systems with high chemical affinity (mutual solubility, formation of intermediate interface compounds). In the case of eutectic-type systems, heteroepitaxy of diffusant at substrate surface results in formation of dense films.