石墨炉原子吸收法快速测定血液中铅和镉

建立了快速测定血液中铅和镉的石墨炉原子吸收光谱法。使用5%硝酸溶液对样品进行脱蛋白处理,然后在旋涡混合器上振摇,离心后取上清液上石墨炉原子吸收进行测定。 结果表明,Pb、Cd工作曲线线性关系良好,相关系数均大于0.9994;方法检出限分别为4.32μg/L和0.27μg/L;Pb的回收率为91.60%～97.31%,镉的回收率为97.04%～98.86%;Pb测定的RSD（n=7）为2.35%,Cd测定的RSD（n=7）为1.53%。冻干牛血铅、镉标准物质GBW09139k和GBW09140k的测定值与参考值吻合。该方法快速准确,精密度、准确度、检出限等测定结果令人满意。可以作为日常血铅、血镉的检测的方法。     

Direct atomic absorption spectrometry determination of tin, lead, cadmium and zinc in high-purity graphite with flame furnace atomizer

This work described methodology of Sn, Pb, Cd and Zn impurities determination in high-purity graphite at direct atomic absorption spectrometry (AAS) with flame furnace (FF) atomizer. It was evidence that quality of AAS measurements are depended from sample amount, its homogeneity, particle size, as well as calibration procedure and operation parameters of FF atomizer. Prior to analysis the method has been developed and optimized with respect to the furnace heating temperature and flame composition of FF atomizer. Conditions of absorption peak areas (Q_A) formation to each element were studied on the basis of contribution into its value some of individual parameters of analytes, including mass-transporting process from increasing mass of graphite samples into gas phase. Because particle size and homogeneous distribution of analyte in powdered materials has an enormous influence on accuracy and precision of measurement results, graphite as well as appropriate series of powdered reference standards was previously ground and investigated. Graphite samples to be analyzed and standard reference materials with mass from 0.025 to 0.200 g was previously briquetted as pellet and insert on corresponding hole in furnace. The characteristic mass (g₀) of Sn, Pb, Cd and Zn were 0.35, 0.1, 0.008 and 0.025 ng, respectively, and relative standard deviation (S_r) not more than 20%.     

Fast determination of lead and copper in dairy products by graphite furnace atomic absorption spectrometry

A rapid and direct procedure for determining lead and copper in dairy products by electrothermal atomic absorption spectrometry (ETAAS) is described. Samples are slurried in a medium containing 50% v/v hydrogen peroxide, 1% v/v nitric acid, 0.5% w/v dihydrogen phosphate, and 20% v/v ethanol and directly injected into the furnace with no previous mineralization. Calibration is performed with aqueous standards. Limits of determination were 0.4 and 2.4 ng/mL for copper and lead, respectively. The reliability of the procedure was checked by comparison with the acid mineralization procedure and by analyzing 3 certified reference milk samples.     

Determination of cadmium,copper and lead in mineral coal using solid sampling graphite furnace atomic absorption spectrometry

Solid sampling graphite furnace atomic absorption spectrometry (SS-GF AAS) was investigated as a potential technique for the routine determination of trace elements in mineral coal and cadmium, copper and lead were chosen as the model elements. Cadmium and lead could be determined at their main resonance lines at 228.8 nm and 283.3 nm, respectively, but an alternate, less sensitive line had to be used for the determination of copper because of the high copper content in coal. No modifier was necessary for the determination of copper and calibration against aqueous standards provided sufficient accuracy of the results. For the determination of cadmium and lead two different modifiers were investigated, palladium and magnesium nitrates in solution, added on top of each sample aliquot before introduction into the atomizer tube, and ruthenium as a ‘permanent’ modifier. Both approaches gave comparable results, and it is believed that this is the first report about the successful use of a permanent chemical modifier in SS-GF AAS. Calibration against solid standards had to be used for the determination of cadmium and lead in order to obtain accurate values. The agreement between the values found by the proposed procedure and the certificate values for a number of coal reference materials was more than acceptable for routine purposes. The detection limits calculated for 1 mg of coal sample using the ‘zero mass response’ were 0.003 and 0.007 μg g⁻¹ for cadmium with the permanent modifier and the modifier solution, respectively, approximately 0.04 μg g⁻¹ for lead, and 0.014 μg g⁻¹ for copper.     

Direct determination of cadmium in urine using graphite furnace atomic absorption spectrometry with Zeeman-effect background correction

A procedure is described for the direct determination of cadmium in human urine using graphite furnace atomic absorption spectrometry with Zeeman-effect background correction. Except for a straightforward 1 + 1 V/V dilution of samples with 1.5% nitric acid, no matrix modifier or sample pre-treatment was necessary, thus reducing the risk of contamination. The concentration of cadmium in urine was evaluated directly from a calibration graph prepared using a metal-spiked human urine pool. In this way the time-consuming method of standard additions was avoided, permitting an increased sample throughput (120-150 samples per day; 90 s per analysis) with minimal attention of the analyst. In routine use, the precision (both within day and day to day) and limit of detection were of the order of less than 10% and 0.05 micrograms l-1 of Cd, respectively. The method is suitable for the biological monitoring of cadmium in the general population or in occupationally exposed persons.     

Cloud point extraction for the determination of cadmium and lead in biological samples by graphite furnace atomic absorption spectrometry

The phase-separation phenomenon of non-ionic surfactants occurring in aqueous solution was used for the extraction of Cd and Pb from digested biological samples. After complexation with O,O-diethyldithiophosphate (DDTP) in hydrochloric acid medium, the analytes are quantitatively extracted to the phase rich in the non-ionic surfactant octylphenoxypolyethoxyethanol (Triton X-114) after centrifugation. Methanol acidified with 0.1 mol L⁻¹ HNO₃ was added to the surfactant-rich phase prior to its analysis by electrothermal atomic absorption spectrometry (ET AAS). The adopted concentrations for DDTP, Triton X-114 and hydrochloric acid were all optimized. Pyrolysis and atomization temperatures were optimized using the extracts and pyrolysis temperatures of 700 °C for both elements and atomization temperatures of 1400 and 1600 °C for cadmium and lead, respectively, were used without adding any modifier, which shows that considerable analyte stabilization is provided by the medium itself. A more detailed investigation was carried out to determine which components of the extract were responsible for the high thermal stability achieved and it revealed that the amount of DDTP added and the phosphorus content of the digested samples contributed significantly to this phenomenon. Detection limits (3σ_B) of 6 and 40 ng g⁻¹, along with enrichment factors of 129 and 18 for Cd and Pb, respectively, were achieved. The proposed procedure was applied to the analysis of five certified biological reference materials after microwave-assisted acid digestion in a mixture of H₂O₂ and HNO₃. Comparison with certified values was performed for accuracy evaluation, resulting in good agreement according to the t-test for a 95% confidence level. The high efficiency of cloud point extraction to carry out the determination of the studied analytes in complex matrices was, therefore, demonstrated.     

石墨炉原子吸收光谱法测定中药口服液中的铬铅镉

利用石墨炉原子吸收光谱法测定,采用常温消解和密闭微波消解等方式处理口服液样品,并进行比较。结果表明,采用HNO3 HClO4 H2O2作为消解试剂用常温消解方式进行消解后,可不加基体改进剂直接进行测定,在此基础上研究了石墨炉原子吸收测定的最佳条件。应用这种方法测定了双黄连、清开灵、生脉饮和抗病毒口服液中痕量镉、铬和铅,RSD小于5．0％,回收率在83．4％～113％。     

Determination of cadmium,copper and lead in alumina based catalysts by direct solid sampling graphite furnace atomic absorption spectrometry

Trace impurities of Cd, Cu and Pb were determined in alumina based catalysts using direct solid sampling graphite furnace atomic absorption spectrometry (DSS-GF AAS). The analyzed catalysts are widely used in petrochemical processes. The following analytical parameters were evaluated: pyrolysis and atomization temperatures, feasibility of calibration with aqueous solutions, the necessity for palladium as chemical modifier and the sample mass introduced into the atomizer. Test samples between 0.05 and 8.5 mg were used. Palladium was investigated as chemical modifier but no improvement in analytical performance was obtained and its use was considered unnecessary for all elements. The results obtained by DSS-GF AAS were compared with those of inductively coupled plasma optical emission spectrometry (ICP OES) and also with conventional solution analysis by GF AAS (Sol-GF AAS). Characteristic masses were 1.4, 9 and 20 pg, for Cd, Cu and Pb, respectively. Using DSS-GF AAS the relative standard deviation was always less than 10% and the results agreed with those obtained by Sol-GF AAS and ICP OES. Calibration using aqueous solutions showed good linearity within the working range (R² better than 0.99). Limits of detection (3σ, n = 10) for Cd, Cu and Pb using the proposed procedure were 0.2, 22, and 1.2 ng g^− 1, respectively.     

Direct and simultaneous determination of copper and manganese in seawater with a multielement graphite furnace atomic absorption spectrometer

The direct and simultaneous determinations of Cu and Mn in seawater using a multielement graphite furnace atomic absorption spectrometer (Perkin-Elmer SIMAA6000) are described. Three kinds of chemical modifier (Mg(NO₃)₂, Pd(NO₃)₂ and a mixture of these) were tested. The matrix interferences were removed completely so that a simple calibration curve method could be used to determine Cu and Mn in seawater from the open ocean using Pd or a mixture of Pd and Mg as the chemical modifier. The relative standard deviations (RSDs) for the simultaneous determination of Cu and Mn in seawater from open ocean are 10% or less, and the detection limits were 0.07 μg 1⁻¹ for Cu and 0.10 μg 1⁻¹ for Mn, using Pd as the chemical modifier. The accuracy of the method is confirmed by analysis of four kinds of certified reference saline waters.     

Effects of various salts on the determination of arsenic by graphite furnace atomic absorption spectrometry. Direct determination in seawater

The effect of Na, Mg, Ca and Sr as their nitrate, chloride and sulfate salts and seasalt, with and without the use of palladium, on the determination of arsenic by electrothermal atomic absorption spectrometry was investigated. In the absence of any stabilizing agent, arsenic was partially lost as molecular species at low temperatures. The effect of salts on the shape of the atomization signal, the integrated absorbance and the stabilizing effect were highly dependent both on their nature and mass. By trapping arsenic, oxide species resulting from the decomposition of nitrate salts induced a high stabilization effect depending on their vaporization temperatures: MgO approximately CaO>SrO>Na2O. The stabilization effect of chlorides occurred about 200 degrees C lower and depended on mass, volatility and hydrolytic properties: SrCl2>CaCl2>MgCl2 approximately NaCl. The effect of sulfates was mainly dependent on their decomposition/vaporization mechanisms, and in the presence of Na2SO4 or CaSO4 a strong chemical interference effect was observed. Palladium stabilized arsenic in the presence of nitrates, chlorides or even sulfates, leading to a similar delaying effect, signal shape and integrated absorbance. Seasalt induced also important modifications to the atomization signal of As. Moreover, an interference effect was observed, which could probably be attributed to the simultaneous vaporization of sulfate in seasalt. In seawater, Pd suppressed this interference effect and permitted to use a high pyrolysis temperature up to 1400 C to remove the major part of the seawater matrix before atomization. Under optimized conditions, the detection limit for As obtained in unmodified seawater in the presence of Pd was 0.34 microg L(-1) for a 10 microl sample.     

Effects of various salts on the determination of arsenic by graphite furnace atomic absorption spectrometry. Direct determination in seawater

The effect of Na, Mg, Ca and Sr as their nitrate, chloride and sulfate salts and seasalt, with and without the use of palladium, on the determination of arsenic by electrothermal atomic absorption spectrometry was investigated. In the absence of any stabilizing agent, arsenic was partially lost as molecular species at low temperatures. The effect of salts on the shape of the atomization signal, the integrated absorbance and the stabilizing effect were highly dependent both on their nature and mass. By trapping arsenic, oxide species resulting from the decomposition of nitrate salts induced a high stabilization effect depending on their vaporization temperatures: MgO～CaO>SrO>Na₂O. The stabilization effect of chlorides occurred about 200?°C lower and depended on mass, volatility and hydrolytic properties: SrCl₂>CaCl₂>MgCl₂～NaCl. The effect of sulfates was mainly dependent on their decomposition/vaporization mechanisms, and in the presence of Na₂SO₄ or CaSO₄ a strong chemical interference effect was observed. Palladium stabilized arsenic in the presence of nitrates, chlorides or even sulfates, leading to a similar delaying effect, signal shape and integrated absorbance. Seasalt induced also important modifications to the atomization signal of As. Moreover, an interference effect was observed, which could probably be attributed to the simultaneous vaporization of sulfate in seasalt. In seawater, Pd suppressed this interference effect and permitted to use a high pyrolysis temperature up to 1400?°C to remove the major part of the seawater matrix before atomization. Under optimized conditions, the detection limit for As obtained in unmodified seawater in the presence of Pd was 0.34 μg L^–1 for a 10 μl sample.     

Rapid determination of lead, cadmium and thallium in cements using electrothermal atomic absorption spectrometry with slurry sample introduction

 A method is proposed for the determination of Pb, Cd and Tl in cements by ETAAS. The samples are suspended in a medium containing 10% v/v ethanol and 1% v/v both conc. nitric and hydrofluoric acids and are directly introduced into the electrothermal atomizer. The drying stage is performed by programming a 400 °C temperature, a ramp time of 5 s and a hold time of 30 s on the power supply to the atomizer. No ashing step is used. Atomization is carried out at 2100, 1800 and 1700 °C for Pb, Cd and Tl, respectively. For Cd determination, ammonium dihydrogen phosphate is added to the suspension medium. No modifier other than hydrofluoric acid is required for the Pb and Tl determination. It is shown that the results obtained by using direct calibration with aqueous standards for five commercial samples agree with those found by means of the standard additions method. Received: 29 March 1996/Revised: 24 May 1996/Accepted: 30 May 1996     

The atomic absorption determination of antimony,arsenic, bismuth, cadmium, lead, and tin in iron, copper,and zinc alloys with the graphite furnace

Antimony, arsenic, bismuth, cadmium, lead, and tin can be determined in metallurgical samples by flame atomic absorption spectrometry at levels of 0.005 wt%, but lower concentrations frequently necessitate preconcentration. The graphite furnace allows determination of these elements at concentrations 1–2 orders of magnitude lower than is possible with flame techniques. All six elements have detection limits at or below 1μg g⁻¹ in a variety of alloys. Calibration for antimony and load was done with standards containing the principal component of the alloy as a synthetic matrix. Bismuth, cadmium, and tin could be determined accurately only by the standard addition method. Arsenic could be determined in iron alloys with synthetic standards, but standard additions were required for copper alloys.     

Direct and simultaneous determination of arsenic, manganese, cobalt and nickel in urine with a multielement graphite furnace atomic absorption spectrometer

A simple method was developed for the direct and simultaneous determination of arsenic (As), manganese (Mn), cobalt (Co), and nickel (Ni) in urine by a multi-element graphite furnace atomic absorption spectrometer (Perkin-Elmer SIMAA 6000) equipped with the transversely heated graphite atomizer and longitudinal Zeeman-effect background correction. Pd was used as the chemical modifier along with either the internal furnace gas or a internal furnace gas containing hydrogen and a double stage pyrolysis process. A standard reference material (SRM) of Seronorm™ Trace Elements in urine was used to confirm the accuracy of the method. The optimum conditions for the analysis of urine samples are pyrolysis at 1350 °C (using 5% H₂ v/v in Ar as the inter furnace gas during the first pyrolysis stage and pure Ar during the second pyrolysis stage) and atomization at 2100 °C. The use of Ar and matrix-free standards resulted in concentrations for all the analytes within 85% (As) to 110% (Ni) of the certified values. The recovery for As was improved when mixture of 5% H₂ and 95% Ar (v/v) internal furnace gas was applied during the first step of a two-stage pyrolysis at 1350 °C, and the found values of the analytes were within 91-110% of the certified value. The recoveries for real urine samples were in the range 88-95% for these four elements. The detection limits were 0.78 μg l⁻¹ for As, 0.054 μg l⁻¹ for Mn, 0.22 μg l⁻¹ for Co, and 0.35 μg l⁻¹ for Ni. The upper limits of the linear calibration curve are 60 μg l⁻¹ (As); 12 μg l⁻¹ (Mn); 12 μg l⁻¹ (Co) and 25 μg l⁻¹ (Ni), respectively. The relative standard deviations (R.S.D.s) for the analysis of SRM were 2% or less. The R.S.D.s of a real urine sample are 1.6% (As), 6.3% (Mn), 7.0% (Ni) and 8.0% (Co), respectively.     

Direct determination of atmospheric lead by Zeeman solid sampling graphite furnace atomic absorption spectrometry (GFAAS)

Summary Atmospheric lead was collected by membrane filters using two low volume air samplers at Jülich, Stolberg, and Wetzlar, Federal Republic of Germany. Sampling times varied from 2 to 8 h. After sampling, each filter was subsampled in two cross-sections using a clean stainless steel punch (diameter 5 mm). The lead content of each subsample disc was determined directly by Zeeman GFAAS, calibrated with aqueous standard solutions and supported by solid reference materials. The distribution of lead between the subsamples was generally homogeneous, with standard deviations ranging from 11 to 37%, but typically <15% for samples with 8 h sampling time. The analysis of each filter usually took about 30 min. The differences in air quality between the three sampling locations, as measured by the lead concentrations, are discussed. In general, Stolberg appears to have the highest lead concentrations. The mass particle-size distribution of lead in the aerosol samples collected by membrane filters using a cascade impactor at Stolberg was also investigated with the same analytical technique. Using graphite platform boats as direct samplers, it is possible for the dry deposition flux of lead to be estimated. This provides a quick means of assessing the levels of lead pollution in the atmospheric environment. With lead concentrations measured in parallel, the dry deposition velocities of lead can be estimated under various meteorological conditions. Application of similar sampling and analytical techniques to other atmospheric trace metals may be possible.     

Direct determination of iron in urine and serum using graphite furnace atomic absorption spectrometry

A simple, rapid and low-cost method for the routine determination of iron in urine and serum using graphite furnace atomic absorption spectrometry is described which may provide an alternative to the more widespread automated spectrophotometric methods. The urine and serum samples were simply diluted with water prior to analysis. Matrix modification was found to be redundant. The standard additions technique or the use of matrix matched standards (addition calibration) was found to be unnecessary and, therefore, the calibration was performed using aqueous standards. For serum analysis the degree of dilution could be reduced by using the less sensitive 302.0-nm resonance line, yielding more precise determinations, and for urine analysis, interferences were eliminated by means of a L'vov platform. The interferences that exist in the presence of nitric acid are also discussed. Finally, the presence of background absorption was investigated by means of Zeeman effect atomic absorption.     

Instrumentation for simultaneous multielement atomic absorption spectrometry with graphite furnace atomization

Graphite furnace-atomic absorption spectrometry (GF-AAS) is restricted to the determination of 4 to 6 elements simultaneously due to the limitations of hollow cathode lamps. However, a consideration of prototype continuum source instruments and recent advances in the fields of spectrometer and detector technology suggests that a multielement GF-AAS instrument, with the multielement versatility associated with atomic emission spectrometry, is possible. Such a multielement instrument would employ a continuum source and provide 1.) multielement determinations for 30 to 40 elements, 2.) wavelength and time integrated absorbance measurements which are independent of the source width, 3.) detection limits comparable to line source AAS with the potential for another order of magnitude improvement using atomization at elevated pressures, 4.) extended calibration ranges limited only by the memory of the atomizer, and 5.) high resolution inspection of the spectra surrounding the analytical wavelength. Such an instrument could provide figures of merit comparable to inductively coupled plasma-mass spectrometer with considerably less complexity.     

Instrumentation for simultaneous multielement atomic absorption spectrometry with graphite furnace atomization

Graphite furnace-atomic absorption spectrometry (GF-AAS) is restricted to the determination of 4 to 6 elements simultaneously due to the limitations of hollow cathode lamps. However, a consideration of prototype continuum source instruments and recent advances in the fields of spectrometer and detector technology suggests that a multielement GF-AAS instrument, with the multielement versatility associated with atomic emission spectrometry, is possible. Such a multielement instrument would employ a continuum source and provide 1.) multielement determinations for 30 to 40 elements, 2.) wavelength and time integrated absorbance measurements which are independent of the source width, 3.) detection limits comparable to line source AAS with the potential for another order of magnitude improvement using atomization at elevated pressures, 4.) extended calibration ranges limited only by the memory of the atomizer, and 5.) high resolution inspection of the spectra surrounding the analytical wavelength. Such an instrument could provide figures of merit comparable to inductively coupled plasma-mass spectrometer with considerably less complexity.     

Direct determination of traces of copper,zinc, lead,cobalt, iron and cadmium in bovine liver by graphite furnace atomic absorption spectrometry using the solid sampling and the platform techniques

A simple and rapid method is described for direct determination of traces of Cu, Zn, Pb, Co, Fe and Cd in NBS bovine liver, SRM 1577, by graphite furnace atomic absorption spectrometry. The solid sampling technique was used, thereby avoiding the dilution factor involved in the solution technique, and also the risk of contamination from the environment in sample handling and from reagents, solvents and vessels. The organic matrix was burnt off and removed by using a well-defined selective volatilization technique combined with the analyte modification technique. Also, the effect of the platform technique in removing matrix interferences was studied using an anisotropic pyrolytic graphite platform inside the commercial graphite tube. The results of the “with platform” and the “without platform” techniques were equally accurate, but the “with platform” technique gave better precision.     

Preconcentration of lead in biological matrices for graphite furnace atomic absorption spectrometry

Lead was transferred by a two-step extraction procedure from complicated biological matrices into an aqueous solution. Thereafter, lead could be accurately determined in the aqueous solution without interference by graphite furnace atomic absorption spectrometry (GFAAS). Biological samples were digested sequentially by a mixture of sulphuric acid and nitric acids and a strong oxidant, potassium peroxodisulphate. Lead was extracted by dithiocarbamate in chloroform from the digest solution and subsequently back-extracted into a mercury(II) solution. Matrix materials such as chloride, phosphate and sulphate, which were known to cause serious interference in the determination of lead by GFAAS, could be eliminated in the preconcentration procedure. Close to 90% recovery of lead was achieved. The proposed procedure was applied for the analysis of several NBS biological standard reference materials containing lead in the mg kg^?1 range and satisfactory results were obtained.