毛细管电泳电化学法分离检测盐酸克伦特罗、特布他林和沙丁胺醇

建立了毛细管电泳电化学法对盐酸克伦特罗、特布他林和沙丁胺醇进行分离检测。方法采用胶束电泳体系,以铂圆盘为工作电极,考察了检测电位、缓冲液浓度和pH、十二烷基硫酸钠(SDS)浓度、分离电压等因素的影响。3个分离物在10 kV的分离电压、缓冲体系为15 mmol/L(pH 9.0)硼砂+20 mmol/L SDS条件下得到分离。盐酸克伦特罗、特布他林和沙丁胺醇的线性范围分别为2.0～400,3.5～700,5.0～1000μg/L。方法已用于猪肉样品的检测。     

Quantitative determination of clenbuterol, salbutamol and tulobuterol enantiomers by capillary electrophoresis

Enantiomers of clenbuterol, salbutamol and tulobuterol were directly separated and quantitated from a spiked sample by capillary electrophoresis (CE) using sulfated β-cyclodextrin (SCD) as chiral selector and phosphate as running buffer. The SCD and buffer concentration, pH and field strength were the parameters studied to optimize the separation. Optimal separation was obtained using 50 mM of phosphate monobasic at pH = 2.24, 0.25% (w/w) of sulfated cyclodextrin and a field strength of 10 kV, with 20 min total time analysis. Comparison between two different injection modes (hydrodynamic and electrokinetic) was made. In the hydrodynamic mode, repeatability (expressed as relative standard deviation, RSD) was less than 1.2% for migration times for all the analyte peaks and less than 2% for peak area percentages. With respect to reproducibility, RSD was less than 3.8% for migration time and less than 3% for peak area percentages. Calibration curves were set up for two different sample concentration ranges (1 to 10 μg mL^–1 and 160– 800 ng mL^–1, of each of the racemates studied). Although the electrokinetic injection mode for an aqueous sample appeared to suffer from some enantiodiscrimination, calibration curves were linear in the range between 1 and 10 ng mL^–1 with regression coefficients ranging from 0.9996 to 0.9952. As in the case of hydrodynamic injection, the method was tested with a spiked sample.     

Quantitative determination of clenbuterol, salbutamol and tulobuterol enantiomers by capillary electrophoresis

Enantiomers of clenbuterol, salbutamol and tulobuterol were directly separated and quantitated from a spiked sample by capillary electrophoresis (CE) using sulfaited beta-cyclodextrin (SCD) as chiral selector and phosphate as running buffer. The SCD and buffer concentration, pH and field strength were the parameters studied to optimize the separation. Optimal separation was obtained using 50 mM of phosphate monobasic at pH = 2.24, 0.25% (w/w) of sulfated cyclodextrin and a field strength of 10 kV, with 20 min total time analysis. Comparison between two different injection modes (hydrodynamic and electrokinetic) was made. In the hydrodynamic mode, repeatability (expressed as relative standard deviation, RSD) was less than 1.2% for migration times for all the analyte peaks and less than 2% for peak area percentages. With respect to reproducibility, RSD was less than 3.8% for migration time and less than 3% for peak area percentages. Calibration curves were set up for two different sample concentration ranges (1 to 10 microg mL(-1) and 160-800 ng mL(-1), of each of the racemates studied). Although the electrokinetic injection mode for an aqueous sample appeared to suffer from some enantiodiscrimination, calibration curves were linear in the range between 1 and 10 ng mL(-1) with regression coefficients ranging from 0.9996 to 0.9952. As in the case of hydrodynamic injection, the method was tested with a spiked sample.     

Quantitative determination of salbutamol in tablets by multiple-injection capillary zone electrophoresis

A multiple-injection capillary zone electrophoresis (MICZE) method has been developed for the assay of salbutamol in Ventoline Depot tablets (GlaxoSmithKline). In the developed method, seven sample sets, each consisting of three samples, were sequentially injected into the capillary and analyzed within a single run. This enabled a total of twenty-one sequential injections, i.e., six standards and fifteen samples, containing salbutamol and the injection marker oxprenolol. The injected sample plugs were separated by plugs of background electrolyte, through application of a short-term voltage (30kV) over the capillary for different time periods, i.e., t(PE1) and t(PE2). The samples in each set were isolated from each other by partial electrophoresis for 2.35min (t(PE1)), while the sample sets were separated for 10.50min (t(PE2)). After the final injection, all the applied samples were subjected to electrophoresis for a time period corresponding to that in conventional single-injection CZE. The method was validated regarding linearity, accuracy, precision and robustness before it was applied to the determination of salbutamol in 15 tablets of Ventoline Depot with a labeled content of 8mg salbutamol. The average salbutamol content was determined to 7.8mg (+/-0.3mg) from simultaneous analyses of the 15 different tablets.     

Separation and determination of coumarins from Cacalia tangutica by capillary zone electrophoresis

Capillary zone electrophoresis (CZE), using a 20 mmol/L borate buffer at pH 10.5, was developed for the identification and determination of three coumarins--7-hydroxy-coumarin (HC), 7-hydroxy-8-methoxy-coumarin (HMC) and 7-O-beta-D-glucosyl-coumarin (GC)--in the extracts of the flower of Cacalia tangutica. Regression equations revealed linear relationships (correlation coefficient 0.9986-0.9990) between the corrected peak area (the ratio of peak area to migration time) of each constituent and its concentration. The relative standard deviations (RSD) of the migration time and peak area were 1.45-1.52 and 2.60-3.84% (intra-day), and 1.75-2.22 and 2.90-4.04% (inter-day), respectively. The recoveries of three constituents ranged between 94.5 and 105.6%. The effects of pH value, buffer concentration and applied voltage on the migration behavior of HC, HMC and GC were investigated. The contents of the three active constituents in the flower of Cacalia tangutica were successfully determined within 6 min under the optimum conditions chosen. Moreover, the dissociation constants for three coumarins were also determined by CE.     

Separation and simultaneous determination of quinolone antibiotics by capillary zone electrophoresis

Summary The potential of capillary zone electrophoresis has been investigated for the separation and quantitative determination of some quinolone antibiotics. The influence of different conditions, such as the nature and concentration of the electrophoretic electrolyte, on migration time, peak symmetry, efficiency and resolution was studied. A buffer consisting of 100mm HEPES adjusted to pH 8.5 containing 10% (v/v) acetonitrile was found to furnish a very efficient and stable electrophoretic system for the separation of exoxacin, ciprofloxacin, ofloxacin, oxolinic acid, nalidixic acid and pipemedic acid. A linear relationship between concentration and peak area for each compound was obtained in the concentration range 0.25–40 μg mL⁻¹; detection limits were approximately 0.25 ng mL⁻¹. It was demonstrated that the method can be used for the simultaneous determination of these six antibiotics in serum and urine samples.     

Separation and determination of cations in beverage products by capillary zone electrophoresis

Cation determination is important for quality control of beverage products. To determine a large group simultaneously, a capillary electrophoresis procedure is developed with indirect UV at 214 nm in a three-complex buffer system (10 mM N,N-dimethylbenzylamine (DBA), 8 mM lactic acid and 2 mM 18-crown-6) with good mobility matching with desired cations. Under optimized conditions with pH adjusted to 4.65, a baseline separation is achieved for 14 cations (Rb(+), NH(4)(+), K(+), Ca(2+), Na(+), Mg(2+), Mn(2+), Co(2+), Fe(2+), Cd(2+), Cr(3+), Ni(2+), Zn(2+) and Cu(2+)) within 7 min using an uncoated silica column. To cover ng/l to mug/l range, both hydrostatic and electrokinetic sampling are studied, showing working ranges within (0.05-50)/(0.005-2) microg/l and detection limits (13-78)/(1.4-10) ng/l, respectively with satisfactory repeatability (RSD 0.31-0.47% for migration time, and 3.0-4.0% for peak height measurement). Agreeable results with established inductively coupled plasma-atomic emission spectrometry method have been obtained for orange juice and tea samples.     

Enantiomeric separation of racemic clenbuterol by capillary zone electrophoresis

A method for capillary electrophoretic enantiomeric separation of a racemic clenbuterol has been established with hydroxypropyl-β-cyclodextrin as the chiral selector. General equations and data analysis are presented to relate mobility to the equilibrium constants in simple binding equilibria and used to determine binding constants and thermodynamic parameters for host-guest complexation of clenbuterol enantiomers with hydroxypropyl-β-cyclodextrin as a selector. The effects of β-cyclodextrin type and concentration, buffer type, concentration and pH, as well as separation voltage and capillary temperature were investigated in detail. A maximal resolution of 6.78 was obtained. The binding constants of the host-guest complex of clenbuterol enantiomers with hydroxypropyl-β-cyclodextrin, K _R-CD and K _S-CD are 22.50 and 43.09 l mol^-1, respectively.     

Separation and determination of nitroaniline isomers by capillary zone electrophoresis with amperometric detection

In this paper, capillary zone electrophoresis with amperometric detection (CZE-AD) was firstly applied to the simultaneous separation and determination of nitroaniline positional isomers. The three analytes could be perfectly analyzed by using the buffer of extreme pH. The effects of several important factors were investigated to find optimum conditions. A carbon-disk electrode was used as working electrode. The optimal conditions were 40 mmol/L tartaric acid-sodium tartrate (pH 1.2) as running buffer, 17 kV as separation voltage and 1.10 V (versus saturated calomel reference electrode, SCE) as detection potential. Under the optimum conditions, o-, m- and p-nitroaniline were separated successfully and good linearity, reproducibility and recovery results were obtained. The detection limit for m-nitroaniline was as low as at 9.06 × 10⁻⁹ mol/L. This proposed method demonstrated long-term stability and reproducibility with relative standard deviations of less than 1.8% for migration time and 1.1% for peak areas. The utility of this method was demonstrated by monitoring dyestuff wastewater and the assay results were satisfactory.     

区带毛细管电泳法分离测定洋金花中莨菪烷类生物碱

采用区带毛细管电泳法分离测定洋金花中3种莨菪烷类生物碱—阿托品、山莨菪碱和东莨菪碱。以57 cm×50μm熔融石英毛细管为分离通道,工作电压25 kV,温度25℃,200 mmol/L Tris-H3PO4(pH=8.3)为背景电解质。经优化分离条件,3种莨菪烷类生物碱达到基线分离,此方法快速、简便,可作为中药材洋金花中有效成分分离的方法和质量控制方法。     

Separation of nitrophenols by capillary zone electrophoresis

Separation conditions suitable to a rapid resolution of a group of eight nitrophenols by capillary zone electrophoresis (CZE) were found. Required differences in their effective mobilities were achieved via host-guest complexation of -cyclodextrin combined with intermolecular interactions involved by polyvinylpyrrolidone. When both additives were present in the carrier electrolyte at pH=9.1 nitrophenols could be separated in the column of a, 300 m I.D. and 180 mm in the length within 8–9 minutes. It is shown that the column of such an I.D. providing enhanced sample load capacity, can operate with high separation efficiencies as maintaining zone dispersions due to Joule heating on a tolerable level. CZE on-line coupled with isotachophoretic sample pretreatment is shown to provide the concentration limits of detection at low ppb concentrations by using an on-column photometric detector operating at 254 and 405 nm detection wavelengths.     

Separation of nicotine metabolites by capillary zone electrophoresis and capillary zone electrophoresis/mass spectrometry

The use of capillary zone electrophoresis (CZE) and capillary zone electrophoresis/mass spectrometry (CZE/MS) has been demonstrated, in principle, for the separation of nicotine and nicotine metabolites. The buffer system developed for separation and detection by CZE/UV was modified for use in CZE/MS analysis. Several of the metabolites are isobaric and tandem mass spectrometric (MS/MS) techniques have been used to differentiate such analytes.     

Field-amplified on-line sample stacking for separation and determination of cimaterol, clenbuterol and salbutamol using capillary electrophoresis

A capillary electrophoresis method, using field-amplified sample injection (FASI), was developed for separation and determination of some beta 2-agonists, such as cimaterol, clenbuterol and salbutamol. The optimum conditions for this system had been investigated in detail. The precision of the migration time, peak height and accuracy were determined in both intra-day (n = 5) and inter-day (n = 15) assays. Under the optimum conditions, the detection limits (defined as S/N = 3) of this method were found to be lower than 2.0 ng/mL for all of these three beta 2-agonists, which were much lower than that of the conventional electro-migration injection method, the enhancement factors were greatly improved to be 30-40-fold. Such lower detection limit lets this method to be suitable for determination of above-mentioned beta 2-agonists in the urine sample. The mean recoveries in urine were higher than 96.2%, 95.6% and 95.3% for cimaterol, clenbuterol and salbutamol, respectively, with relative standard deviations lower than 3.5%.     

Separation of human fibrinopeptides by capillary zone electrophoresis

We describe a method for the simultaneous determination of the five fibrinopeptide forms derived from the thrombin-promoted activation of human fibrinogen by capillary zone electrophoresis (CZE). The fibrinopeptide mixture was first desalted by a solid-phase extraction (SPE) step. The analysis was performed in reversed polarity in a highly cross-linked polyethylene glycol (PEG)-coated capillary with UV-light absorption detection at 200 nm. Several parameters including buffer concentration and pH, presence of an organic modifier, temperature, and applied voltage, have been tested. The best separations were obtained within 20 min, utilizing a 20 mM sodium phosphate buffer without organic modifier, in the narrow 6.1-6.2 pH range, at 25 degrees C, with an applied voltage of 20 kV. Quantitative analysis is made possible by the use of sheep fibrinopeptide A as an internal standard to correct for both extraction and injection errors.     

Separation and determination of magnolol and honokiol inMagnolia officinalis bark by capillary zone electrophoresis

The effects of pH on separation parameters such as migration mobility, resolution, sensitivity, column efficiency and peak shape were emphatically studied. Better separation of magnolol and honokiol using capillary zone electrophoresis was achieved by optimizing pH in the range 5.0–11.7. The influences of applied voltage and temperature were also investigated. We adopted a better sample extraction procedure by which higher contents of honokiol and magnolol with sample compositions unchanged were obtained. The analysis was performed with direct UV detection using a 10 mM borate-10 mM phosphate buffer at pH of 11.6. The method was successfully applied to the simultaneous determination of magnolol and honokiol inMagnolia officinalis bark within 9 min.     

Separation of flavonoids and phenolic acids from propolis by capillary zone electrophoresis

The simultaneous determination of twelve different flavonoids, pinocembrin, acacetin, chrysin, rutin, catechin, naringenin, galangin, luteolin, kaempferol, apigenin, myricetin, and quercetin, two phenolic acids, cinnamic acid and caffeic acid, and one stilbene derivative, resveratrol, in propolis extracts used in medicine has been investigated by capillary zone electrophoresis (CZE). With a buffer constituted by sodium tetraborate 30 mM, pH 9.0, and 15 kV applied voltage, the 15 polyphenols were separated on an uncoated fused-silica capillary within 40 min using normal polarity. Under the experimental conditions used, a linear relationship was calculated between the CZE migration times and the molecular weight of polyphenols' expression of the increasing amount of their hydroxyl groups and polarity. Regression equations revealed a linear relationship (correlation coefficients > 0.97) between the peak area of each polyphenol species and their concentration, from 6 to 120 ng. The levels of analytes in three different propolis extracts, ethanolic, aqueous-ethanolic and aqueous-glycolic, used to prepare various commercial medicinal products, were determined. The aqueous-ethanolic propolis extract showed a great percentage of caffeic acid, galangin, quercetin, and chrysin, whilst the ethanolic preparation was composed of a great amount of resveratrol, chrysin, and caffeic acid. On the contrary, the aqueous-glycolic propolis preparation was composed of approx. 11% of caffeic acid and a low amount of the other identified flavonoids due to the presence of approx. 85% of nonidentified compounds. CZE represents a valuable method for the qualitative and quantitative assay of the most relevant polyphenol components of propolis, representing an alternative to obtain typical fingerprints of propolis and a reliable identification of a large number of propolis polyphenolic species.     

Rapid determination of salbutamol in pharmaceutical preparations by chiral capillary electrophoresis

A fast and simple method of chiral capillary electrophoresis (CE) has been applied to the analysis of salbutamol in different pharmaceutical preparations. Using of a 25 mM acetate buffer (pH 5.0), containing 13.1 mg/mL carboxymethyl-beta-cyclodextrin (CM-beta-CD), an applied voltage of 20 kV and a temperature of 25 degrees C, the enantiomers of salbutamol could be separated in about 2 min. Three different pharmaceutical preparations (two syrups, one oral solution, and two kind of tablets) containing a racemate of salbutamol were injected directly in the CE system, following dilution in dimethyl sulfoxide (DMSO). Appreciable differences in the retention times were observed for salbutamol enantiomers in the different formulations studied, which were attributed to the effect of the matrix components on the electrophoretic mobility. The standard addition method was used for the calibration due to the existence of matrix interferences. Finally, the stability of the enantiomers of salbutamol in the oral solution was studied calculating the enantiomeric ratio values when the solution was injected immediately after being opened in the first case and after being opened and stored in the fridge for two months in the second case.     

Separation of the enantiomers of four chiral drugs by neutral cyclodextrin-mediated capillary zone electrophoresis

Summary Neutral cyclodextrin (CD)-modified capillary zone electrophoresis (CZE) has been applied to the chiral separation of four basic drugs— clorprenaline, benzhexol, esmolol and terazosin. Selector screening and concentration optimization experiments were performed. The resolution was 3.9 for clorprenaline, 2.3 for benzhexol, 3.1 for esmolol and 1.2 for terazosin when the running electrolyte was 60 mM hydroxypropyl-β-CD, 15 mM heptakis (2,3,6-Tri-O-methyl)-β-CD, 60 mM γ-CD and 60 mM heptakis (2,6-di-O-methyl)-β-CD, respectively, in 50 mM, pH 2.5 sodium phosphate buffer.     

Separation and identification of platinum adducts with DNA nucleotides by capillary zone electrophoresis and capillary zone electrophoresis coupled to mass spectrometry

Platinum adducts are supposed to be the cytotoxic lesions in DNA after platinum-containing anticancer therapy. Various adducts are formed upon interaction of platinum complexes with nucleotides, but contribution of individual adducts to antitumor activity and toxicity of platinum complexes still remains to be examined. A capillary zone electrophoresis (CZE) method is described that is suitable to separate individual platinum adducts. We investigated the formation of adducts following the reaction of cis-diamminedichloroplatinum (II) (cisplatin) with various DNA nucleotides. Baseline separation of unmodified and modified nucleotides (adducts) was achieved using uncoated fused-silica capillaries and basic separation buffers. In order to elucidate the observed peak pattern, a coupled CZE-electrospray ionization-mass spectrometry (ESI)-MS approach was applied. After incubation of mononucleotides with cisplatin, monochloro, monoaqua and bifunctional adduct species were detected. Consequently, the migration order of nucleotides and individual platinum adducts could be determined. Moreover, the time-dependent conversion from monochloro to monoaqua and subsequently to bifunctional adducts was monitored. In conclusion, individual platinum adducts were separated by CZE and identified by CZE-ESI-MS. Formation and conversion of distinct species were confirmed. Potential applications comprise studies of novel platinum complexes, investigations of platinum-adduct formation with DNA, and determination of platinum-DNA adducts in cells.     

Separation and determination of l-tyrosine and its metabolites by capillary zone electrophoresis with a wall-jet amperometric detection

A method of capillary electrophoresis with wall-jet amperometric detection (AD) has been developed for separation and determination of l-tyrosine (Tyr) and its metabolites, such as Tyramine (TA), p-hydroxyphenylpyruvic (pHPP), homogentisic acid (HGA) and some dipeptides containing Tyr, such as Tyr-Gly-Gly (YGG), Tyr-Arg (YR) and Tyr-d-Arg (Y-d-R). A carbon disk electrode was used as the working electrode and the optimal detection potential was 1.00 V (versus Ag/AgCl). At 18 kV of applied voltage, the seven compounds were completely separated within 20 min in 110 × 10⁻³ mol/L Na₂HPO₄-NaH₂PO₄ buffer (pH 7.10) containing 3 × 10⁻³ mol/L β-cyclodextrin (β-CD). Good linear relationship was obtained for all analytes and the detection limits of seven analytes were in the range of 0.95-4.25 ng/mL. The proposed method has been applied to examine the metabolic process of l-tyrosine in rabbit's urine.