A novel, environmentally friendly dispersive liquid-liquid microextraction procedure for the determination of copper

A novel, simple and environmentally friendly procedure for copper determination has been developed. The method is based on the formation of an ion associate of Cu(I) with 1,3,3-trimethyl-2-[5-(1,3,3-trimethyl-1,3-dihydroindol-2-ylidene)-penta-1,3-dienyl]-3H-indolium (DIDC) in the presence of chloride ions as ligand, followed by dispersive liquid-liquid microextraction (DLLME) of the formed ion associate into organic phase and UV-Vis spectrophotometric detection. The following experimental conditions were used: pH 3, 0.24 mol L^− 1 chloride ions, 0.06 mmol L^− 1 DIDC. The effect of the nature of the extraction solvent, auxiliary solvent and disperser solvent used was studied. A mixture of amyl acetate, tetrachloromethane, and methanol in a 1:1:3 v/v/v ratio was selected for the DLLME procedure. The absorbance of the coloured extracts at 640 nm wavelength obeys Beer's law in the range 0.020-0.090 mg L^− 1 of Cu. The limit of detection calculated from a blank test (n = 10) based on 3s is 0.005 mg L^− 1 of Cu. The developed procedure was applied to the analysis of water samples. The suggested DLLME is compared with two procedures previously reported from our laboratory based on (1) conventional liquid-liquid extraction, and (2) sequential injection extraction performed in a dual-valve sequential injection system. The advantages and disadvantages of each method are discussed.     

Separation of chromium (VI) using complexation and its determination with GFAAS

In acidic medium and in the presence of chloride ions 2-[2-(4-methoxy-phenylamino)-vinyl]-1,3,3-trimethyl-3H-indolium chloride forms complex with Cr(VI). The optimum conditions (pH, concentration of Cl^- and the complex forming reagent) of the separation and extraction of Cr(VI) into toluene using this basic dye as a complexing reagent have been determined and the possible interferences of Ca, Mg, Na, K, Cr(III), Ni, Pb, Hg, Mn, Al, Cu have been studied. An electrothermal atomic absorption spectrometer (GFAAS) was used for the determination of Cr(VI). The detection limit of the method for Cr(VI) found to be 0.15 μg dm^− 3 and RSD for spiked drinking water was better than 3%.     

Determination of platinum(IV) by UV spectrophotometry

A simple, rapid and sensitive spectrophotometric procedure for the determination of platinum has been elaborated. Pt traces were determined in the form of the PtCl(6)(2-) complex in hydrochloric acid solution whose concentration varies from 0.01 to 2 mol L(-1) by measuring the absorbance at 260 nm. The detection limit is 4.7 x 10(-7) mol L(-1), the linearity range from 2 x 10(-6) mol L(-1) to 7 x 10(-6) mol L(-1), and the correlation coefficient is r=0.9990. No significant interferences were observed from a majority of the investigated ions, such as Zn(II), Pb(II), Mn(II), Cd(II), Co(II) and Ni(II) with the exception of Cu(II), Sb(III), Fe(III), Pd(II), Sn(II) and I(-) ions. The method was successfully applied for the determination of Pt traces in different solid samples and the recovery from inorganic materials was studied.     

Speciation of Co(II), Co(III), and Cu(II) in ethylenediamine solutions by capillary electrophoresis

A capillary electrophoretic (CE) method for the speciation of Co(II), Co(III), and Cu(II) in electroless copper-plating baths containing ethylenediamine (En) has been developed. The method is based on the selective pre-capillary derivatization of Co(II) with 1,10-phenanthroline (Phen) followed by CE separation of stable [CoPhen(3)](2+), [CoEn(3)](3+), and [CuEn(2)](2+) chelates. The proposed derivatization procedure protects Co(II) from oxidation by dissolved oxygen and enables rapid determination of all three metal species within a single run. The optimized separations were carried out in a fused silica capillary (57 cmx75-microm I.D.) filled with an ethylenediamine sulfate electrolyte (20 mmol L(-1) H(2)SO(4), pH 7.0 with En, applied voltage +30 kV) using direct UV detection at 214 nm. The detection limits for a signal-to-noise ratio of 3 and 10 s, hydrodynamic injections were 5x10(-6) mol L(-1) for Cu(II), 1x10(-6) mol L(-1) for Co(III), and 4x10(-7) mol L(-1) for Co(II). Application of the method to the speciation of Co(II), Co(III), and Cu(II) in copper-plating bath samples is also demonstrated.     

Fluorimetric determination of copper(II) in aqueous solution using lucifer yellow CH as selective metal reagent

Lucifer yellow CH is shown to be a highly selective fluorescent reagent for the determination of Cu(III) in the microg L(-1) concentration range. The fluorophore is statically quenched by Cu(II); the carbohydrazide group was assigned as the complexing part of the dye molecule. A total range of Cu(II) determination from 0.06 mg L(-1) (1 micromol L(-1)) to 6.3 mg L(-2) (100 micromol L(-1)) with a limit of detection of 0.019 mg L(-1) (0.3 micromol L(-1)) was obtained, along with surprisingly high selectivity. There was no interference from alkaline and earth alkaline metal ions. The cross sensitivity to heavy metal ions was evaluated by the separate solution method and by competitive binding experiments. Calibration plots are shown for Cu(II) determination at different pH and the dissociation constant was determined. The application of the reagent was demonstrated by the determination of the Cu(II) content of tap water samples.     

Determination of trace molybdenum in vegetable and food samples by spectrophotometry with p-carboxyphenylfluorone

A new highly sensitive and selective chromogenic reagent, p-carboxyphenylfluorone (p-CPF), was studied for spectrophotometric determination of trace molybdenum. In 0.36 mol L(-1)phosphoric acid medium, p-CPF reacts with molybdenum(VI) to form a 1:3 red complex, which has a sensitive absorption peak at 531 nm. Under optimal conditions, the reaction of molybdenum(VI) with p-CPF completed rapidly and absorbance remains almost constant for at least 24 h. Molybdenum(VI) obeyed Beer's law in the range 0-2.0 microg mL(-1); the apparent molar absorption coefficient, Sandell's sensitivity and the limit of detection were found to be 1.03 x 10(5) L mol(-1) cm(-1), 1.028 ng cm(-2)and 0.73 ng mL(-1) respectively; the effect of various foreign ions were examined in detail. It was found that most coexisting ions can be tolerated in considerable amounts, especially 800 mg of Mn(II), 200 mg of Mg(II), Fe(II), Co(III), Ni(II) and Cd(II), 50 mg of Ca(II) and Al(III), 25 mg of Cu(II) and Fe(III), 10 mg of Hg (II), La(III), Bi(III), Pb(II) and Zn(II) don't interfere with the determination of molybdenum(VI). The proposed method is very simple, sensitive and selective, it has been applied to determine molybdenum in vegetable and food samples with a very high precision and accuracy. Moreover, the synthesis of the reagent and the conditions of the colour reaction were also studied in detail.     

Evaluation of a carbon paste electrode modified with organofunctionalised SBA-15 nanostructured silica in the simultaneous determination of divalent lead, copper and mercury ions

The performance of a carbon paste electrode (CPE) modified with SBA-15 nanostructured silica organofunctionalised with 2-benzothiazolethiol in the simultaneous determination of Pb(II), Cu(II) and Hg(II) ions in natural water and sugar cane spirit (cacha?a) is described. Pb(II), Cu(II) and Hg(II) were pre-concentrated on the surface of the modified electrode by complexing with 2-benzothiazolethiol and reduced at a negative potential (-0.80 V). Then the reduced products were oxidised by DPASV procedure. The fact that three stripping peaks appeared on the voltammograms at the potentials of -0.48 V (Pb2+), -0.03 V (Cu2+) and +0.36 V (Hg2+) in relation to the SCE, demonstrates the possibility of simultaneous determination of Pb2+, Cu2+ and Hg2+. The best results were obtained under the following optimised conditions: 100 mV pulse amplitude, 3 min accumulation time, 25 mV s(-1) scan rate in phosphate solution pH 3.0. Using such parameters, calibration graphs were linear in the concentration ranges of 3.00-70.0 x 10(-7) mol L(-1) (Pb2+), 8.00-100.0 x 10(-7) mol L(-1) (Cu2+) and 2.00-10.0 x 10(-6) mol L(-1) (Hg2+). Detection limits of 4.0 x 10(-8) mol L(-1) (Pb2+), 2.0 x 10(-7) mol L(-1) (Cu2+) and 4.0 x 10(-7) mol L(-1) (Hg2+) were obtained at the signal noise ratio (SNR) of 3. The results indicate that this electrode is sensitive and effective for simultaneous determination of Pb2+, Cu2+ and Hg2+ in the analysed samples.     

Spectrophotometric determination of manganese with derivatives of 1,3,3-trimethyl-2-[3-(1,3,3-trimethyl-1,3- H-indol-2-ylidene)propenyl]-3 H-indolium

A new, simple, rapid, and sensitive spectrophotometric method has been developed for the determination of manganese in sewage. The method is based on the reaction of manganese with derivatives of 1,3,3-trimethyl-2-[3-(1,3,3-trimethyl-1,3-H-indol-2-ylidene)propenyl]-3H-indolium to form a colored ion associate with a sensitive absorption maximum at 560 nm. The appropriate reaction conditions have been established: pH 8.5–10.0, 1.25–2.3×10^–3 mol L^–1 1-nitroso-2-naphthol, and 1.6–2.4×10^–4 mol L^–1 dye reagent. Beer's law is obeyed for manganese concentrations up to 4.2 mg L^–1. The limit of detection is 0.01 mg L^–1 Mn²⁺; the molar absorptivity of the ion associate was 7.5×10⁴ L mol^–1 cm^–1. The effect of various foreign ions was examined. A reaction mechanism is suggested. The developed procedure was tested for determination of manganese in sewage with satisfactory precision and accuracy.     

Determination of niobium in pyrochlore ore by differential pulse polarography

A differential pulse polarographic method has been developed for the quantitative determination of niobium in pyrochlore ore. One-step polarographic curves were obtained in 0.01 mol L(-1) EDTA as supporting electrolyte. Analytical curves indicated that response was linearly dependent on Nb(V) concentration between 1.6 and 8.6 mg L(-1) in the pH range 2-5. The system is quasi-reversible and controlled by diffusion in 0.01 mol L(-1) EDTA as supporting electrolyte; the electrode process involves one-electron reduction of Nb(V) to Nb(IV). The results obtained so far for niobium in pyrochlore ore were comparable with those obtained by X-ray fluorescence determination. Ions such as Fe(III), Cr(III), As(III), Cu(II), Ni(II), Co(II), Mn(II), Sn(IV), Zn(II), V(V), Ta(V), W(VI), Ce(IV), and Ti(IV) did not interfere. Possible interference from Pb(II) can be avoided by complexation with the supporting electrolyte in the pH range 3.5 to 4.6; Mo(VI) ions can be tolerated when their concentration is one-tenth that of Nb(V).     

Ion-selective electrode for aluminum determination in pharmaceutical substances, tea leaves and water samples

A novel ion-selective PVC membrane sensor for Al(III) ions based on 6-(4-nitrophenyl)-2-phenyl-4-(thiophen-2-yl)-3,5-diaza-bicyclo[3.1.0]hex-2-ene (NTDH) as a new ionophore has been prepared and studied. The electrode exhibit a good response for aluminum ion over concentration range of 1.0x10(-6) to 1.0x10(-1) mol L(-1) with a Nernstian slope of 19.6+/-0.4 mV per decade and low detection limit of 6.3x10(-7) mol L(-1). The best performance was obtained with membrane composition 30% poly(vinyl chloride), 62% acetophenone, 5% oleic acid, 3% ionophore and 2 ml tetrahydrofuran. NTDH-based electrode was suitable for aqueous solutions of pH 3. It has relatively fast response time (approximately 10 s) and can be used at least for 3 months without any considerable divergence in potentials. The proposed membrane electrode revealed good selectivity for Al(III) ions over a wide variety of other cations. The standard electrode potentials were determined at different temperatures and used to calculate the isothermal coefficient of the electrode. The formation constant and stoichiometry ratio of ionophore-Al(III) complex were calculated at 25 degrees C by using segmented sandwich membrane method. It was used in non-aqueous solvents and also as indicator electrode in potentiometric determination of Al(III) ions in some real samples.     

Separation and determination of trace amounts of aluminium(III), vanadium(V), iron(III), copper(II) and nickel(II) with CALKS and PAR by RP-HPLC.

An RP-HPLC method for the separation and determination of aluminium(III), vanadium(V), iron(III), copper(II) and nickel(II) with CALKS (Chromazol KS) and PAR ([4-(2-pyridylazo)resorcinol]) chelating on a YWG-ODS column was developed. A mixture of methanol-tetrahydrofuran(THF)-water (60:5:35 v/v) containing 0.2 mol/L LiCl, 5 x 10(-5) mol/L CALKS, 5 x 10(-5) mol/L PAR and acetate buffer solution (pH 4.9) was selected as mobile phase. The method has high sensitivity, with the detection limits being 6 ng/mL for aluminium(III), 3.5 ng/mL for vanadium(V), 10.4 ng/mL for iron(III), 6.3 ng/mL for copper(II) and 8.7 ng/mL for nickel(II). It also has good selectivity, so that most foreign metal ions do not interfere under the optimum conditions. The method can be applied to the simultaneous determination of trace amounts of aluminium, vanadium, iron, copper and nickel in rice and flour samples.     

Selective preconcentration, separation and speciation of ferric iron in different samples using N,N'-bis(2-hydroxy-5-bromo-benzyl)1,2 diaminopropane

The synthesis and analytical applications of N,N'-bis(2-hydroxy-5-bromo-benzyl)1,2 diaminopropane (HBDAP) are described. This compound reacts with Fe(III) in the range of pH 3-6 to produce a red complex (2:3 mol ratio of Fe(III)/HBDAP) soluble in chloroform. The investigation included a study of the characteristics that are essential for solvent extraction and for spectrophotometric determination and speciation of iron. A highly sensitive, selective and rapid spectrophotometric method is described for the determination of trace amounts of iron(III) by HBDAP. The complex obeys Beer's law from 0.056 to 1.68 mg l(-1) with an optimum range. The detection limit (taken as three times the standard deviation of the reagent blank) is approximately 1.23x10(-7) M Fe(III) and the limit of quantitation (taken as ten times the standard deviation of the reagent blank) is about 4.11x10(-7) M Fe(III). A single extraction gave a good separation of iron(III) from iron(II). Good separation of Fe(III) from Ni(II), Fe(II), Co(II), Cd(II), Mn(II), Zn(II), Pb(II) was also achieved at pH 3-5.     

New reagent for indirect spectrophotometric red-ox determination of osmium (Ⅵ)

A highly sensitive indirect spectrophotometric red-ox method for the determination of osmium is reported. The method is based on the oxidation of iodide by osmium (VI) and the spectrophotometric detection of the liberated iodine in the form of complex anion and ion associate with 2-(4-diethylaminostyryl)-1,3,3-trimethyl-6-nitro-3H-indolium chloride reagent. The appropriate reaction conditions have been established. The molar absorptivity is (1.6-5.6)×104 L mol-1cm-1. Beer's law holds for the concentration range of 0.5-11.4μgmL-1 of Os(Ⅵ).     

Simultaneous determination of Cu(II) and Ag(I) on SP Sephadex C25 as complexes with 1-phenyl-1,2-propanedione-2-oximethiosemicarbazone by derivative spectrophotometry

A simple, rapid, and sensitive method has been developed for the simultaneous determination of trace amounts of copper and silver using 1-phenyl-1,2-propanedione-2-oximethiosemicarbazone (PPDOT) as a chromogenic reagent. The proposed method was based on retention and preconcentration of the complexes Cu(III)-PPDOT and Ag(I)-PPDOT on a solid phase in acid medium. The complexes were quantitatively retained in the cation exchanger SP Sephadex C25, and the analytical measurements were executed directly in the solid phase by derivative spectrophotometry. In this simultaneous determination, the second derivative and the zero crossing method were used. The determination of copper and silver was carried out to 321.0 and 427.0 nm, respectively. In order to obtain quantitative recoveries of the metal ions, various experimental analytical parameters, such as pH, stirring time, volume, and amount of solid phase, were optimized. The effect of interfering ions on the determination was described. The recovery values for Cu(II) and Ag(I) were found to be > 98%, and the relative standard deviation was < or = 2%. The detection limits (3sigma criterion) for Cu(II) and Ag(I) were found to be 0.9 x 10(-8) and 13 x 10(-8) M, respectively. The developed method was utilized for preconcentration and determination of Cu(II) and Ag(I) in industrial effluents and natural water samples. The results were consistent with those provided by inductively coupled plasma/mass spectrometry.     

Chemometric study of selected polychlorinated biphenyls in ambient air of Madrid (Spain)

The formation of Fe(III) and Fe(II) chelates with pyridylazo and thiazolylazo reagents was examined. Optimum conditions for the formation of Fe(III) and Fe(II) chelates with 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (5-Br-PADAP) were in detail evaluated. The LC method for simultaneous separation of Fe(III) and Fe(II) ions as 5-Br-PADAP chelates was evaluated using the PEEK column with C18 e.c. stationary phase and acetonitrile+water (90:10, v/v) eluent containing the 1x10(-3) mol l(-1) C(12)H(25)SO(3)Na, the ion-pairing reagent, pH 3.4-3.6. The simultaneous determination of 20-500 mug l(-1) Fe(II) ions (detection at 555 nm) and 20-500 mug l(-1) Fe(III) ions (detection at 585 nm) as 5-Br-PADAP chelates (for both ions, detection limit, 18 mug l(-1) for 20 mul loop) was established. The chromatographic method was applied to the water analysis. Although the present method is able to determine both Fe(III) and Fe(II) ions, the Fe(III) ion was not detected in all water samples. The Fe(II) was detected only in fresh gathered oligocene water at the level of 135 mug l(-1). The present method was used to the investigation of the distribution of Fe(III)/Fe(II) ions in aqueous and micellar solutions after action of external, ultrasonic field.     

Copper(II) modified carbon paste electrodes based on self-assembled mercapto compounds-gold-nanoparticle

Three mercapto compounds [2-mercapto-5-(1-methyl-5-nitroimidazole-2-yl)-1,3,4-thiadiazole] (MMNIT), [2-mercapto-5-(5-nitrofuran-2-yl)-1,3,4-thiadiazole] (MNFT) and [2-mercapto-5-(5-nitrothiophen-2-yl)-1,3,4-thidiazole] (MNTT) were used for self-assembled-gold nanoparticle (SAGNP) modified carbon paste electrodes. The electrodes were applied as indicator electrodes for potentiometric determination of Cu(II) ion. The prepared electrodes exhibit a Nernstian slope of 31.0+/-0.5 mV per decade for Cu(II) ion over a wide concentration range of 7.9x10(-9)-3.2x10(-2), 7.9x10(-9)-7.9x10(-4), and 2.8x10(-8)-7.9x10(-3) mol L(-1) for MMNIT, MNFT and, MNTT, respectively. The detection limits of electrodes were 3.5 (+/-0.2)x10(-9), 4.1x10(-9), and 4.1x10(-8) mol L(-1) of copper ion, respectively. The potentiometric responses of electrodes based on MMNIT, MNFT, and MNTT are independent of the pH of test solution in the pH range 2.0-5.5, 2.5-7.0, and 2.0-6.5, respectively. They have quick response with response time of about 5 s. The proposed electrodes show fairly good selectivity over some alkali, alkaline earth, transition and heavy metal ions. Finally, the proposed electrodes were successfully employed to detect Cu(II) ion in hair and water samples.     

Catalytic spectrophotometric determination of trace aluminium with indigo carmine

A new catalytic spectrophotometric method is described for the determination of trace amounts of Al(III). The methods based on catalytic action of Al(III) on the oxidation of indigo carmine (IC) by ammonium persulfate in hexamethylene tetramine-hydrochloric acid ((CH2)6N4-HCl) buffer medium (pH 5.4) and in the presence of surfactant-TritonX-100. The effects of some factors on the reaction speed were investigated. Aluminium concentration is linear for 0-1.2x10(-7) g/ml in this method. The detection limit of the proposed method is 1.96x10(-8) g/ml. Most of the foreign ions except for Cu(II), Fe(III) do not interfere with the determination, and the interference of Cu(II) and Fe(III) in this method can be removed by extraction with sodium diethyldithiocarbamate-carbon tetrachloride (DDTC-CCl4). This system is a quasi-zero-order reaction for Al(III), but it is a quasi-first-order reaction for IC. The apparent rate constant is 2.62x10(-5) s-1 and the apparent activation energy is 6.60 kJ/mol in the system. The proposed method was applied to the determination of trace aluminium(III) in real samples with satisfactory results.     

The separation of aluminum(III) ions from the aqueous solution on membrane filter using Alizarin Yellow R

The membrane filtration was examined as an effective and selective method for collection of Al(III) ions from aqueous solutions using Alizarin Yellow R, one of a pH-indicator, as a precipitating reagent. For preparation of aqueous solutions without precipitate or turbidity, a non-ionic surfactant, Triton X-100, was used as a solubilizing reagent for insoluble materials. Three metal ions, Al(III), V(III) and Cu(II) ions, were able to be collected as yellow-orange precipitates from aqueous solutions controlled in a range of pH 4-7, pH 4-9, and pH 5.5-12, respectively, on a membrane filter by filtration under suction. Hydrogen peroxide and o-phenanthroline were found to be capable of masking V(III) and Cu(II) ions in a range of pH 5.5-8 in which Al(III) ions were collected. This membrane filtration was applied to selective separation and determination of Al(III) ions in tap water.     

Determination of polyamines by flow injection analysis with a chemiluminescence detector based on their complexation with copper(II).

Through the flow injection analysis experiments, we discovered that an unsaturated complex of Cu(II) and polyamines (spermine, spermidine, putrescine) had a strongly catalytic effect on luminol-H(2)O(2) chemiluminescence (CL) reaction, and that the CL intensity is proportional to the concentrations of polyamines. Based on the automatic formation of an unsaturated complex of polyamines and Cu(II) when the solution containing polyamines passed through a column packed with solid Cu(OH)(2), a new flow injection chemiluminescence analysis method was proposed for the determination of polyamines. The effects of pH, buffer concentration, the concentration of chemiluminescence reagent, and the influence of mixing coil length were examined. Under optimal conditions, the linear range was from 1.0 x 10(-7) mol L(-1) to 1.0 x 10(-5) mol L(-1), and the detection limits were 0.17, 0.38, 0.44 pmol for spermine, spermidine, and putrescine, respectively. Compared with other methods, the advantages of this method include convenience, time-saving and low cost.     

Synergistic effect of Ni(II) and Co(II) ions on the sulfite induced autoxidation of Cu(II)/tetraglycine complex

The synergistic effect of Ni(II) and Co(II) on the sulfite induced autoxidation of Cu(II)/tetraglycine was investigated spectrophotometrically at 25.0 degrees C, pH = 9.0, 1 x 10(-5) mol dm(-3) < or = [S(IV)] < or = 8 x 10(-5) mol dm(-3), [Cu(II)]= 1 x 10(-3) mol dm(-3), 1 x 10(-6) mol dm(-3) < or = [Ni(II)] or [Co(II)] < or = 1 x 10(-4) mol dm(-3), [O2] approximately 2.5 x 10(-4) mol dm(-3), and 0.1 mol dm(-3) ionic strength. In the absence of added nickel(II) or cobalt(II), the kinetic traces of Cu(III)G4 formation show a large induction period (about 3 h). The addition of trace amounts of Ni(II) or Co(II) increases the reaction rate significantly and the induction period drastically decreases (less than 0.5 s). The effectiveness of Cu(III)G4 formation becomes much higher. The metal ion in the trivalent oxidation state rapidly oxidizes SO3(2-) to SO3*-, which reacts with oxygen to produce SO5*-. The strongly generated oxidants oxidize Cu(II)G4 to Cu(III).