Capacitance of Organic Schottky Diodes Based on Copper Phthalocyanine （CuPc）

The capacitance of an organic Schottky diode based on copper phthalocyanine （CuPc） is investigated. Based on the organic small-signal equivalent model established, we calculate the reverse capacitance CMetal Of the organic Schottky diode with different kinds of metal cathodes （Mg, Al, Au）. It is found that the reverse capacitance of the organic Schottky diode shows behavior as CMg 〉 CAl 〉 CAu at the same frequency, and according to our analysis, the reverse Schottky junction capacitance Cj is expected to have little effect on the reverse capacitance of the organic Schottky diode, and the space-charge limited current capacitance Us is considered to dominate the reverse capacitance, which limits the improvement of frequency characteristics of organic Schottky diodes.     

Organic Light Emitting Diodes Using Doped Alq3 as the Hole-transport Layer

Effects of 2,3,5,6-tetrafluoro-7,7,8,8-tetracyanoquinodimethane （F4TCNQ） doping on the hole conductivity of Alq3 layer are measured. In the hole-only device of Alq3, the current densities increase in 1-3 orders of magnitude upon doping with F4TCNQ, suggesting that the doping can effectively enhance the hole-injection and hole- transport ability of Alq3. An organic light-emitting device using an F4TCNQ doped Alq3 layer as the hole- injection and hole-transport layer, and pristine Alq3 as the electron-transport and emitting layer is fabricated and characterized. Bright emission is achieved in the simple OLED with p-doped Alq3 as the hole-transport layer and the intrinsic Alq3 as the electron-transport and emitting layer. The emitting efficiency and brightness of the device are further improved by inserting a thin electron block layer to confine the carrier recombination zone in the middle of the organic layers.     

Organic Light-Emitting Diodes with Magnesium Doped CuPc as an Efficient Electron Injection Layer

Bright organic electroluminescent devices are developed using a metal-doped organic layer intervening between the cathode and the emitting layer. The typical device structure is a glass substrate/indium-tin oxide （ITO）/copper phthalocyanine （CuPc）/N,N＇-bis-（1-naphthl）-diphenyl-1,1＇-biphenyl-4,4＇-diamine （NPB）/Tris（8-quinolinolato） aluminum（Alq3）/Mg-doped CuPc/Ag. At a driving voltage of 11 V, the device with a layer of Mg-doped CuPc （1：2 in weight） shows a brightness of 4312cd/m^2 and a current efficiency of 2.52cd/A, while the reference device exhibits 514 cd/m^2 and 1.25 cd/A.     

High efficiency small molecule white organic light-emitting devices with a multilayer structure

In this paper, a new white organic light-emitting device (WOLED) with multilayer structure has been fabricated. The structure of devices is ITO/N, N-bis-(1-naphthyl)-N, N^′-diphenyl-1, 1′-biphenyl-4, 4′-diamine (NPB) (40 nm)/NPB: QAD (1%): DCJTB (1%) (10 nm) /DPVBi (10 nm) /2, 9-dimethyl, 4, 7-diphenyl, 1, 10-phenanthroline (BCP) (d nm)/tris-(8-hydroxyquinoline) aluminium (Alq₃)(50-d nm)/LiF (1 nm)/Al (200 nm). In our devices, a red dye 4-(dicyanomethylene)-2-t-butyl-6 (1, 1, 7, 7-tetramethyl julolidyl-9-enyl)-4H-pyran (DCJTB) and a green dye quinacridone (QAD) were co-doped into NPB. The device with 8 nm BCP shows maximum luminance of 12 852 cd/m² at 20 V. The current efficiency and power efficiency reach 9.37 cd/A at 9 V and 3.60 lm/W at 8 V, respectively. The thickness of the blocking layer permit the tuning of the device spectrum to achieve a balanced white emission with Commission International de’Eclairage (CIE) chromaticity coordinates of (0.33,0.33). The CIE coordinates of device change from (0.3278, 0.3043) at 5 V to (0.3251, 0.2967) at 20 V that are well in the white region, which is largely insensitive to the applied bias.     

Blue organic light-emitting diodes with low driving voltage and maximum enhanced power efficiency based on buffer layer MoO3

Blue organic light-emitting devices based on wide bandgap host material, 2-(t-butyl)-9, 10-di-(2-naphthyl) anthracene (TBADN), blue fluorescent styrylamine dopant, p-bis(p-N,N-diphenyl-amino-styryl)benzene (DSA-Ph) have been realized by using molybdenum oxide (MoO₃) as a buffer layer and 4,7-diphenyl-1,10-phenanthroline (BPhen) as the ETL. The typical device structure used was glass substrate/ITO/MoO₃ (5 nm)/NPB (30 nm)/[TBADN: DSA-Ph (3 wt%)](35 nm)/BPhen (12 nm)/LiF (0.8 nm)/Al (100 nm). It was found that the MoO₃∥BPhen-based device shows the lowest driving voltage and highest power efficiency among the referenced devices. At the current density of 20 mA/cm², its driving voltage and power efficiency are 5.4 V and 4.7 Lm/W, respectively, which is independently reduced 46%, and improved 74% compared with those the m-MTDATA∥Alq₃ is based on, respectively. The J-V curves of ‘hole-only’ devices reveal that a small hole injection barrier between MoO₃∥NPB leads to a strong hole injection, resulting low driving voltage and high power efficiency. The results strongly indicate that carrier injection ability and balance shows a key significance in OLED performance.     

Efficient White Light Emission Using a Single Copolymer with Red and Green Chromophores on a Conjugated Polyfluorene Backbone Hybridized with InGaN-Based Light-Emitting Diodes

We report an efficient white-light emission based on a single copolymer/InGaN hybrid light-emitting diode. The single copolymer consists of a conjugated polyfluorene backbone by incorporating 2,1,3-benzothiadiazole （BT） and 4,7-bis（2-thienyl）-2,1,3-benzothiadiazole （DBT） as green and red light-emitting units, respectively. For the single copolymer/InGaN hybrid device, the Commission Internationale de 1＇Eclairage （CIE） coordinates, color temperature Tc and color rendering index Ra at 20mA are （0.323,0.329）, 5960K and 86, respectively. In comparison with the performance of red eopolymer PFO-DBT15 （DOF：DBT=85：15 with DOF being 9＇9- dioctylfluorene） and green copolymer PFO-BT35 （DOF：BT=-65：35） blend/InGaN hybrid white devices, it is concluded that the chemically doped copolymer hybridized device shows a higher emission intensity and spectral stability at a high driving current than the polymer blend.     

Organic Light Emitting Diodes with an Organic Acceptor/Donor Interface Involved in Hole Injection

Organic light emitting diodes with an interface of organic acceptor 3-, 4-, 9-,10-perylenetetracarboxylic dianhydride （PTCDA） and donor copper phthalocyanine （CuPc） involved in hole injection are fabricated. As compared to the conventional device using a 5 nm CuPc hole injection layer, the device using an interface of 10nm PTCDA and 5 nm CuPc layers shows much lower operating voltage with an increase of about 46% in the maximum power efficiency. The enhanced device performance is attributed to the efficient hole generation at the PTCDA/CuPc interface. This study provides a new way of designing hole injection.     

Electroluminescence from Multilayered Diamond/CeF3/SiO2 Films

We report a thin film electroluminescent device with a three-layer structure （diamond/CeF3/SiO2 films）, which has a luminance of 1.5 cd/m^2 at dc voltage 215 V. The electroluminescence spectrum at room temperature shows that the main peaks locate at 527 and 593nm, which are attributed to isolated emission centers of Ce^3＋ ions.     

Air Stability of Cs2CO3:Ag/Ag Cathode for Organic Light-Emitting Diodes

We report the superior stability of the composite Cs2CO3 ：Ag/Ag cathode structure, which can be used in efficient organic light-emitting diodes （OLEDs）. Devices with the Cs2CO3：Ag （1：10, 5nm）/Ag （95nm） cathode show a considerably improved lifetime compared with the control device with the Cs2CO3 （0.5 nm）/Ag （100 nm） cathode. The composite Cs2CO3 ：Ag/Ag film is proved to be stable in the atmosphere. X-ray diffraction （XRD） is applied to analyze the crystalline structure of the Cs2CO3：Ag film, and it is demonstrated that CsAg alloy is formed, leading to the improved stability of the thin film and the devices.     

Electrical Characteristics of Copper Phthalocyanine Thin-Film Transistors with Polyamide-6/Polytetrafluoroethylene Gate Insulator

Polyamide-6（PA 6）/polytetrafluoroethylene is studied as a potential gate dielectric for flexible organic thin film transistors. The same method used for the formation of organic semiconductor and gate dielectric films greatly simplifies the fabrication process of devices. The fabricated transistors show good electrical characteristics. Ambipolar behaviour is observed even when the device is operated in air.