用于苯选择加氢的Ru/Al2O3-ZrO2-NiO/堇青石蜂窝整体催化剂

使用浸涂法和氨气吸收沉积法制备了新型用于苯选择加氢的具有蛋壳型分布的Ru/Al₂O₃-ZrO₂-NiO/堇青石蜂窝整体催化剂,且在固定床整体反应器中对其性能进行了测试.该催化剂显示了较优的选择性和稳定性,并且在低的ZnSO₄浓度(0.5%问题)下环己烯产物收率可达24.7%.采用N₂吸附-脱附法,电感耦合等离子体发射光谱,光学显微镜,扫描电子显微镜及能量色散X射线光谱仪等技术研究了影响催化剂性能的因素.结果表明,NiO的引入减少了涂层中的微孔含量,有利于在低的添加剂浓度下提高环己烯选择性.ZrO₂的存在抑制了涂层的烧结,保证涂层在1373K高温焙烧后仍有较大的比表面积.Ru的蛋壳分布、薄的涂层厚度、较少的微孔含量、较大的比表面积和狭窄的孔分布可能是影响整体蜂窝催化剂中该特殊催化行为的重要因素.     

Thermal Stability of Pt/Al2O3 Catalysts Prepared by Sol-Gel

A series of Pt/Al₂O₃ catalysts were prepared using a sol-gel method. The influence of several parameters used in the synthesis including: metal content, identity of the metal precursor, and the water/alkoxide ratio on the structural properties of the fresh (dried) and calcined samples were studied. It was found that the BET surface area decreased with an increase in the platinum content. A surface area of 500 m²/g was obtained following calcination at 773 K. The structure of fresh samples as determined by FTIR corresponded to that of a pseudoboehmite structure. Samples prepared using a water/alkoxide ratio (H₂O/ATB) of 9 showed a well-defined, uniform pore size distribution following calcination at 773 K. Metal dispersions comparable to those obtained using impregnation methods were obtained. Aging studies (calcination at 873 K for 24 h) performed on these catalysts, exhibited sintering behavior which were similar to Pt/Al₂O₃ catalysts prepared by other methods. The sample prepared using a H₂O/ATB ratio of 9 had the highest surface area and was more thermally resistant towards metal sintering. A bimodal metal particle size distribution was observed: some particles exhibited sintering while others of similar size showed a greater thermal stability to sintering. The sample having the largest surface area and the highest thermal stability following thermal treatment was a consequence of a more condensed structure and a higher pore roughness obtained after drying the gel. This enabled the formation of an alumina structure which was more amorphous and limited aggregation of platinum particles due to surface diffusion within the pore structure.     

Thermal and morphological study of Al2O3 nanofibers derived from boehmite precursor

The boehmite nanofibers were prepared by using NaAlO₂ and Al₂(SO₄)₃ as the starting materials without any surfactant. The phase transitions of the boehmite nanofibres against different temperature were studied and various phases were derived from well-crystallized boehmite nanofibers. All these phases had the same morphology even after high temperature calcination. In addition, the retention of specific surface area of the samples were very high because of the limited aggregation occurred in calcinations for each sample. For instance, the ??-Al₂O₃ obtained at 500?°C had the specific surface area (208.56?m²/g) with an average pore diameter of 6.0?nm. With the further increase of the calcination temperature, the nanofibers became shorter and coarsening, which resulted in the decrease of the specific surface area. It is worthwhile to notice that the BET surface areas (40.97?m²/g) and the pore volume (0.27?cm³/g) of the fibrous structures obtained after 1200?°C calcination are substantially higher than that of the non-fibrous alumina because of the morphology maintenance.     

The optimal temperature of sulfur retention

The effects of calcination temperature on the development of pore size and on the SO₂ sorption capacity have been investigated. It has been shown that the optimal temperature of sulfur retention observed in a fluidized-bed combustor can very possibly be due to pore size variations because of calcinations at different temperatures.     

Characterization and evaluation of the photocatalytic properties of wormhole-like mesoporous silica incorporating TiO2, prepared using different hydrothermal and calcination temperatures

TiO₂?CSiO₂ mesoporous materials were synthesised by deposition of TiO₂ nanoparticles prepared by the sol?Cgel method on to the internal pore surface of wormhole-like mesoporous silica. In this work we synthesised wormhole-like mesoporous silica of different surface area by changing the hydrothermal temperature (70, 100, or 130?°C). Subsequent to this, titania solution was deposited on to the inner surface of the pores and this was followed by calcination at different temperatures (400, 600, or 800?°C). The effect of different hydrothermal and calcination temperature on the photocatalytic properties was evaluated. The samples were characterized by N₂-sorption, X-ray diffraction, X-ray photoelectron spectroscopy, field emission scanning electron microscopy, and transmission electron microscopy. The effect of different hydrothermal and calcination temperatures on the photocatalytic properties was evaluated by measuring the degradation of methylene blue in aqueous solution under UV light irradiation (mercury lamp, 125?W). The results indicated that appropriate surface area and degree of crystallinity are two important factors for obtaining high photocatalytic efficiency. Samples prepared at a hydrothermal temperature of 100?°C and calcined at 800?°C had the best photocatalytic performance, because of the highest surface area and high crystallinity.     

Al2O3催化剂结构对催化臭氧化活性的影响

以Al₂O₃为催化剂催化臭氧化处理邻苯二甲酸二甲酯. 通过XRD、比表面积、孔结构、FTIR和活性评价等方法对催化剂的物化性质及催化活性进行了研究, 考察了焙烧温度、成型粒径对催化剂活性的影响. 结果表明, Al₂O₃催化剂对臭氧化降解邻苯二甲酸二甲酯具有很高的催化活性, 反应120 min后, 总有机碳(TOC)的去除率从单独臭氧氧化的23.9%提高到55.1%; 焙烧温度对催化剂的活性具有很大的影响, 600 ℃催化剂催化活性最高; 随着焙烧温度的升高, Al₂O₃晶型经历了从γ-Al₂O₃到θ-Al₂O₃到α-Al₂O₃的转变, 催化剂的比表面积、焙烧得到的孔容逐渐变小, 晶体粒径变大, 表面•OH数量减少, 催化活性下降. Al₂O₃成型粒径的减小, 提高了催化剂的外比表面积, 减小了内部传质扩散的影响, 从而提高了催化活性.     

Characterization of the calcination process of yttria

A complete characterization of the calcination of precipitates obtained from a continuous operation was carried out in this study. The precipitate was obtained by reacting yttrium nitrate and ammonia solutions in a MSMPR reactor. It precipitated out as yttrium hydroxide nitrate hydrate, which has the general form Y₂(OH)_6-x(NO₃)_x·y H₂O. This compound decomposed in consecutive steps with the last reaction occurring at 525°C.The calcination process was characterized by chemical analysis, X-ray diffraction analysis, DTA and TG. In addition, the physical characteristics of calcined powders, such as specific surface area, particle size distribution, pore volume distribution, X-ray crystallite size and conversion were measured as a function of calcination temperature and time. Finally, the kinetics of the reduction of surface area, the growth of crystallite size and conversion were also examined.     

The effect of F-doping and temperature on the structural and textural evolution of mesoporous TiO2 powders

Mesoporous F⁻-doped TiO₂ powders were prepared by hydrolysis of titanium tetraisopropoxide (TTIP) in a mixed NH₄F-H₂O solution. Effects of F⁻ ion content and calcination temperatures on the phase composition and porosity of mesoporous titania were investigated by X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM) and BET surface areas. The results showed the BET surface area (S_BET) of the pure and doped powders dried at 100°C ranged from 260 to 310 m²/g as determined by nitrogen adsorption. With increasing calcination temperatures, the S_BET values of the calcined titania powders decreased due to the increase in crystalline size. The pore size distribution was bimodal with fine intra-particle pore and larger inter-particle pore as determined by nitrogen adsorption isotherms. The peak pore diameter of intra-particle pore increases with increasing F⁻ ion content. At 700°C, all the titania powders exhibit monomodal pore size distributions due to the complete collapse of the intra-particle pores. The crystallization of anatase was obviously enhanced due to F⁻-doping at 400°C and 500°C. Moreover, with increasing F⁻ ion concent, F⁻ ions not only suppressed the formation of brookite phase at low temperature, but also prevented phase transition of anatase to rutile at high temperature.     

SO2 retention by highly cycled modified CaO-based sorbent in calcium looping process

The limestone modified by pyroligneous acid has been proved to have good CO₂ capture behavior in the calcium looping process. In this work, SO₂ retention of the highly cycled modified limestone in the carbonation/calcination cycles was investigated in a thermogravimetric analyzer (TG). The cyclic carbonation/calcination of the modified limestone was performed in a dual fixed-bed reactor and then the cycled modified limestone was sent for sulfation in TG. The effects of sulfation temperature, cycle number, and prolonged carbonation on SO₂ retention of the cycled modified limestone were discussed. The optimum temperature for sulfation of the cycled modified limestone should be in the range of 900–950 °C. The effect of sulfation temperature on SO₂ retention of the modified limestone drops with increasing cycle number. With increasing cycle number from 20 to 100, the sulfation conversion of the cycled modified limestone is stable and can reach ~0.4. The cycled modified limestone exhibits obviously higher SO₂ retention than the cycled raw one for the same number of cycles. The prolonged carbonation increases SO₂ retention of the modified limestone and the raw one after the subsequent cycles. The sulfation conversions of the modified limestone and the raw one at 118 min after 9-h carbonation in the 20th cycle increase 43 and 56 %, respectively. The cycled modified limestone shows a greater SO₂ retention than the cycled raw one after the same prolonged carbonation treatment. The prolonged carbonation increases the pores in 5–20 nm range which is considered the optimum pore size for sulfation of CaO-based sorbent, so it results in an improvement in SO₂ retention of the cycled sorbents.     

Sulfation behavior of CaO from long-term carbonation/calcination cycles for CO2 capture at FBC temperatures

In this work, SO₂ capture behavior of CaO derived from the dolomite and the limestone during long-term carbonation/calcination cycles for CO₂ capture at fluidized bed combustion (FBC) temperatures was investigated. The cyclic carbonation/calcination of CaO was performed in a dual fixed-bed reactor and then the cycled CaO was sent for sulfation in a thermo-gravimetric analyzer. At the typical FBC temperatures (850–950 °C), SO₂ capture capacity of CaO from the different carbonation/calcination cycles increases with the increasing the temperature. The sulfation conversion of CaO derived from the dolomite (CaO-dolomite) decreases as the carbonation/calcination cycle number increases from 0 to 200. Although the sulfation conversion of CaO derived from the limestone (CaO-limestone) decreases with increasing the cycle number from 0 to 40, its conversion does not always decay with the number of cycles. The sulfation conversion of CaO-limestone shows a slight increase with increasing the cycle number from 40 to 150 and then exhibits a decrease with increasing the cycle number further. The sulfation conversions of CaO-limestone after different cycles are determined by the specific surface area and the volume of macropores >0.2 μm in diameter. The particle size and SO₂ concentration have important effect on sulfation behavior of CaO from various cycles.     

Preparation and characterization of highly photoactive nanocrystalline TiO<Subscript>2</Subscript> powders by solvent evaporationinduced crystallization method

Highly photoactive bi-phase nanocrystalline TiO₂ photocatalyst was prepared by a solvent evaporation-induced crystallization (SEIC) method, and calcined at different temperatures. The obtained TiO₂ photocatalyst was characterized with X-ray diffraction (XRD), transmission electron microscopy (TEM) and BET surface areas. The photocatalytic activity was evaluated by the photocatalytic oxidation of acetone in air. The results show that solvent evaporation can promote the crystallization and phase transformation of TiO₂ at 100°C. When calcination temperatures are below 600°C, the prepared TiO₂ powders show bimodal pore size distributions in the mesoporous region. At 700°C, the pore size distributions exhibit monomodal distribution of the inter-aggregated pores due to the collapse of the intra-aggregated pores. At 100°C, the obtained TiO₂ photocatalyst by this method shows good photocatalytic activity, and at 400°C, its photocatalytic activity exceeds that of Degussa P25. This may be attributed to the fact that the prepared TiO₂ photocatalyst has higher specific surface areas, smaller crystallite size and bimodal pore size distribution.     

Effect of salts on synthesis of mesoporous materials with mixed cationic and anionic surfactants as templates

Mesoporous silica materials were synthesized using tetraеthoxysilane as precursor and liquid crystals formed in aqueous mixtures of cetyl trimethyl ammonium bromide (CTAB) and sodium dodecyl sulfate (SDS) as templates, without and with the addition of NaBr or Na₂SO₄. For this purpose, the formation of liquid crystals as a function of the ratio of CTAB and SDS under different conditions was studied. It was found that liquid crystals formed in the mixed system of CTAB and SDS at certain mixing ratios are well-structured templates for the synthesis of mesoporous silicas. The synthesized silica materials were characterized by transmission electron microscope and nitrogen adsorption/desorption analysis. The pore size of mesoporous silicas could be controlled between 3 to 6 nm by simply changing the concentration of NaBr in solution. The mesoporous silicas exhibited lamellar structure and the order of structural arrangement was promoted with addition of NaBr. However, addition of Na₂SO₄ led to ink-bottle type pores of mesoporous silica with a narrow pore size distribution of around 2 nm and a higher specific surface area of 610 m² g^–1.     

Preparation and characterization of double metal-silica sorbent for gas filtration

This paper presents the preparation of a porous (Mg, Ca) silicate structure, which could be employed as sorbent filter media. The sorbents have been prepared using sodium silicate precipitated with various ratios of magnesium and calcium salts. The sorbents obtained were characterized using scanning electron microscope (SEM), X-ray diffraction (XRD) and nitrogen physisorption isotherm. Further, the applicability and performance of the sorbent impregnate with potassium hydroxide for removal of sulphur dioxide (SO₂) has been demonstrated. From the isotherms, specific surface area, pore diameter and volume of pores were estimated. Results show that the chemical composition and textural properties of the resultant sorbents were highly dependent on Mg/Ca molar ratio. It was found that sorbents made with 68 mol% Mg and 32 mol% Ca (PSS-MgCa-68/32); and 75 mol% Mg and 25 mol% Ca (PSS-MgCa-75/25) exhibited even higher specific surface area and pore volume than the sorbents containing a single metal. The Mg/Ca-silica sorbents obtained contains interconnected bimodal porosity with large portions being mesopores of varied sizes. The pore size distribution (PSD) results further indicate that PSS-MgCa-68/32 sorbent exhibits wide PSD of interconnected pores in the size range of 1 to 32 nm while PSS-MgCa-50/50 and PSS-MgCa-75/25 exhibits narrow PSD of 1 to 5 nm. Using SO₂ as model contaminate gas, it was shown that the dynamic adsorption performance of the PSS-MgCa-sorbents impregnated with 8 wt% KOH exhibits SO₂ uptake, with impregnated PSS-MgCa-68/32 showing better performance. This shows that the materials prepared can be used as adsorbent for gas filtration.     

CO oxidation over Co3O4/SiO2 catalysts: Effects of porous structure of silica and catalyst calcination temperature

The catalytic performances of Co3O4/SiO2 catalysts prepared by incipient wetness impregnation for CO oxidation were investigated using three kinds of silica as carriers with different pore sizes of 7.7, 14.0 and 27.0 nm. The effects of calcination temperature on the catalyst surface and micro structure properties as well as catalytic performance for the oxidation of carbon monoxide were also studied. All catalysts were characterized by N2 adsorption-desorption, XRD, XPS, FTIR, H2-TPR and O2-TPD. It was found that the properties and crystal size of cobalt-containing species strongly depended on the pore size of silica carrier. While the silica pore size increased from 7.7 to 27.0 nm, the Co3O4 crystal size increased from 8.5 to 13.5 nm. Moreover, it was demonstrated that if the spinel crystal structure of Co3O4 was obtained at a calcination temperature as low as 150 ℃, the catalyst sample would have a high Co3O4 surface dispersion and a increase of surface active species, and thus exhibit a high activity for the oxidation of carbon monoxide.     

煅烧温度对Mn改性γ-Fe2O3催化剂结构及低温SCR脱硝活性的影响

采用共沉淀法,在不同煅烧温度下制备一系列Mn改性γ-Fe₂O₃催化剂(Fe_0.7Mn_0.3O_z),研究了煅烧温度对Fe_0.7Mn_0.3O_z催化剂低温SCR脱硝活性的影响,并借助XRD、N₂吸附-脱附、EDS及SEM等手段对催化剂进行表征。结果表明,350 ℃煅烧所得Fe_0.7Mn_0.3O_z催化剂的低温SCR活性最佳,在70 ℃时取得92%的NO_x转化率,100~200 ℃可维持100%的NO_x转化率,而450 ℃煅烧所得催化剂的低温SCR活性最低;煅烧温度为350 ℃时,催化剂具有最大的比表面积和比孔容、发达的孔隙结构及适当结晶度的γ-Fe₂O₃,而煅烧温度为400或450 ℃时,催化剂发生烧结且有α-Fe₂O₃生成,不利于低温SCR反应的进行,因此,Fe_0.7Mn_0.3O_z催化剂的最佳煅烧温度为350 ℃。     

Synthesis and Characterization of Mesoporous Silica Templated by Amphiphilic RTILs

This article reports a novel preparation of mesoporous silica with series of 1-alky-3-methylimidazolium bromide (C_nMIM)Br (n = 12, 14, 16), a kind of amphiphilic room-temperature ionic liquids (RTILs), as a template via a sol-gel nanocasting technique. The pore morphology and structures of these mesoporous silica were characterized by Transmission electron microscopy (TEM). The results show that the RTIL bearing longer alkyl chain is preferred to form the mesoporous silica material with bigger pores. (C₁₆MIM)Br has been chosen to study how the various influencing factors affect the synthesis and structure of the mesoporous silica material, such as the acid concentration, the solling time, the gelling time and the calcination time. N₂ adsorption-desorption isotherms measurement was used to characterize the pore size distribution and BET surface area. The results indicate that all of the factors can make an influence on the preparation of the mesoporous silica, which is more sensitive to the concentration of the acid.     

Synthesis of Thermally Stable MCM-41 at Ambient Temperature

A new process to synthesize thermally stable mesoporous molecular sieves of MCM-41 structure based on delayed neutralization at ambient temperature was investigated. All samples synthesized by this new method have BET surface areas of about 1100m²/g and possess high thermal stability up to 900°C. Higher crystallinity and less lattice constriction after calcination were observed for samples with a longer aging period. Those samples with aging time longer than 10 days exhibited four characteristic XRD peaks of MCM-41 both before and after calcination at 560°C. The N₂ adsorption-desorption isotherms of the calcined samples showed larger average pore size and more homogenous pore size distribution. The method was also successfully applied to the synthesis of MCM-41 with different surfactants of hydrocarbon length with 10–18 carbons and proves to be a simple route for obtaining thermally stable MCM-41 at room temperature.     

Analysis of the kinetic slowing down during carbonation of CaO by CO2

The synthesis of calcium hydroxyapatite powder (Ca-HA) from orthophosphoric acid or from potassium dihydrogen orthophosphate and calcium carbonate was carried out under moderate conditions. A better dissolution of calcium carbonate and a complete precipitation of the orthophosphate species were obtained with orthophosphoric acid, indicating that it may be of interest as a phosphate source compared with potassium dihydrogen orthophosphate. The influence of calcination treatment on the physico-chemical properties of the solids is discussed in this paper. Different characterization techniques such as specific surface area (S _BET), true density, particle size distribution, thermo-mechanical analysis, simultaneous thermogravimetry and differential scanning calorimetry analysis, X-ray diffraction and infrared were performed to understand the phase changes during thermal treatment. Specific surface area decreased while true density and particle size increased with the rise in the calcination temperature, due to the sintering of particles and the chemical reactions occurring at high temperatures. Mixtures of well-crystallized Ca-HA and tricalcium phosphate (TCP) or well-crystallized Ca-HA, CaO, and TCP were obtained after calcination at 800–1,000 °C of the solid products starting from orthophosphoric acid or potassium dihydrogen orthophosphate, respectively.     

Solid surface and field catalysed interface formation of colloidal Al<Subscript>2</Subscript>(SO<Subscript>4</Subscript>)<Subscript>3</Subscript> during Al anodizing affecting the kinetics and mechanism of development and structure of porous oxides

Overall kinetic and potentiometric studies of the growth of porous anodic alumina films in saturated H₂SO₄+Al₂(SO₄)₃ electrolyte showed non-saturation conditions inside the pores and supersaturation conditions at the pore surface/electrolyte interface where the field and the solid surface catalyse the formation of colloidal Al₂(SO₄)₃ micelles. Suitable high-strength field thermodynamically sustained electrochemical and chemical kinetic equations were formulated. It was shown that the diameter and surface fraction of charge exchange at the pore bases, the real pore wall surface fraction where oxide dissolution occurs, and its rate are strongly affected by the conditions. The mechanism of growth and structure of the films are quite different from those in H₂SO₄. A mechanism of regular film growth is imposed and the critical current density, above which pitting appears, strongly increases. The formulated theory may predict improved or new Al anodizing technologies. Electronic Publication     

Synthesis and characterization of high surface area TiO2/SiO2 mesostructured nanocomposite

Recently titania synthesis was reported using various structuration procedures, leading to the production of solid presenting high surface area but exhibiting moderate thermal stability. The study presents the synthesis of TiO₂/SiO₂ nanocomposites, a solid that can advantageously replace bulk titania samples as catalyst support. The silica host support used for the synthesis of the nanocomposite is a SBA-15 type silica, having a well-defined 2D hexagonal pore structure and a large pore size. The control of the impregnation media is important to obtain dispersed titania crystals into the porosity, the best results have been obtained using an impregnation in an excess of solvent. After calcination at low temperature (400 °C), nanocomposites having titania nanodomains (～2–3 nm) located inside the pores and no external aggregates visible are obtained. This nanocomposite exhibits high specific surface area (close to that of the silica host support, even with a titania loading of 55 wt.%) and a narrow pore size distribution. Surprisingly, the increase in calcination temperature up to 800 °C does not allow to detect the anatase to rutile transition. Even at 800 °C, the hexagonal mesoporous structure of the silica support is maintained, and the anatase crystal domain size is evaluated at ～10 nm, a size close to that of the silica host support porosity (8.4 nm). Comparison of their physical properties with the results presented in literature for bulk samples evidenced that these TiO₂/SiO₂ solids are promising in term of thermal stability.