Limitation and improvement of PIV

In this second part of the paper, the Particle Image Distortion (PID) technique is described. It is proposed to overcome the limitations of conventional PIV due to the local deformations u/x, u/y, v/x and v/y in two-dimensional flows. Both simulation and experiment demonstrate that high accuracy and high spatial resolution are possible with this technique. The large time required to compute the cross-correlations, however, limits its wide applications at present.     

Boundary layer stability on a rotating disk with corotation of the surrounding fluid

The stability of the steady self-similar flow in the boundary layer on a rotating disk of infinite radius with corotation of the surrounding fluid is analyzed by the normal mode method. The spectral problem for infinitesimal three-dimensional disturbances is solved by a collocation method with expansion of the amplitude functions in Chebyshev polynomials. It is established that for all values of the parameter 0, equal to the ratio of the angular velocities of the fluid and the disk, the lower critical Reynolds number is determined byA-type, waves, whose development is governed by the parallel instability mechanism typical of an Ekman layer. TheB-type instability, associated with the presence of an inflection point on the velocity profile, disappears when 4. The neutral surfaces are calculated for Karman flow (=0) and Bödewadt flow (). It is found that in Karman flowA-type waves may grow at values of the Reynolds number several times smaller than the critical Reynolds number for spiral vortices. The results of the analysis are compared with the available experimental data.Translated from Izvestiya Rossiiskoi Akademii Nauk, Mekhanika Zhidkosti i Gaza, No.5, pp. 69–77, September–October, 1992.     

Modeling pressure-strain rate correlations in turbulence theory

On the basis of a spectral representation of the rapid part _ij,2 of the correlation tensor p(u _i /x _j ) using Cramer's theorem the inequality _ij,2(U _j /x _i )0 is obtained. As distinct from the realizability conditions, it can serve as a direct and very rigorous test of the adequacy of model expressions for _ij,2. In particular, it is shown that the best known of such expressions do not satisfy this test.Translated from Izvestiya Rossiiskoi Akademii Nauk, Mekhanika Zhidkosti i Gaza, No.2, pp. 42–46, March–April, 1992.     

Asymptotic theory for calculating heat fluxes near the corner of a body

A method is presented for calculating the distribution of the thermal fluxes, friction stresses, and pressure near the corner point of a body contour in whose vicinity the outer supersonic flow passes through an expansion wave. The method is based on a study of the asymptotic solutions of the Navier-Stokes equations as the Reynolds number R approaches infinity for the flow region in which the longitudinal gradients of the flow functions are large, invalidating conventional boundary layer theory. This problem was examined in part in [1], in which the distribution of the friction and pressure in a region with length on the order of a few thicknesses of the approaching boundary layer was obtained in the first approximation. The leading term of the expansion for the thermal flux to the surface of the body vanishes for a value of the Prandtl number equal to unity and for other values of the Prandtl number does not match directly with its value in the undisturbed boundary layer.The thermal-flux distribution is obtained for values of the Prandtl number approaching unity. For this purpose it was necessary to consider a more general double passage to the limit as 1 and 0 for a finite value of the parameter B=[(–1)/] [–ln ^1/4/]^1/4 characterizing the ratio of the effects of thermal conduction, viscous dissipation, and convection. The solution obtained previously [1] corresponds to the particular case B and therefore for actual values of R=10⁴–10⁶, ~ 0.7 overestimates considerably the effect of the dissipative term on heat transfer, although even in first approximation it describes the pressure distribution well and the friction distribution satisfactorily. For smooth matching of the solutions with the corresponding flow functions in the undisturbed boundary layer it was necessary to introduce a flow region with free interaction for the expansion flow. Equations and boundary conditions which describe the flow as a whole are presented. Examples are given of numerical calculations and comparison with experiment.     

Deformed particle image pattern matching in Particle Image Velocimetry

The deformation of particle image patterns due to velocity gradients causes errors of velocity measurements and false velocity detections in PIV (Particle Image Velocimetry). A novel technique to overcome those limitations inherent in the conventional PIV by correcting the particle image pattern according to the local velocity gradients in two dimensional flows, i.e. u/x, u/y, v/x and v/y, is proposed and successfully applied to a water flow downstream of a backward facing step.     

Filament stretching equation in Lagrangian coordinates

The general integral of the very simple equation ^21/n/() was found to describe the cross sectional area of filaments of isothermal power law fluids while in transient stretching where is time and is the initial location of fluid molecules at time = 0 given as the distance from a reference point fixed in space. Any such stretching transient given as a solution of the above equation is physically realizable subject to the restrictions > 0 and/ < 0.     

Optical co-ordinates in general relativity 2 — the problem of distance

Summary Let denote the congruence of null geodesics associated with a given optical observer inV ₄. We prove that determines a unique collection of vector fieldsM₍₎ ( =1, 2, 3) and ₍₀₎ overV ₄, satisfying a weak version of Killing's conditions.This allows a natural interpretation of these fields as the infinitesimal generators of spatial rotations and temporal translation relative to the given observer. We prove also that the definition of the fieldsM₍₎ and ₍₀₎ is mathematically equivalent to the choice of a distinguished affine parameter f along the curves of, playing the role of a retarded distance from the observer.The relation between f and other possible definitions of distance is discussed.

---

Sommario Sia la congruenza di geodetiche nulle associata ad un osservatore ottico assegnato nello spazio-tempoV ₄. Dimostriamo che determina un'unica collezione di campi vettorialiM₍₎ ( =1, 2, 3) e ₍₀₎ inV ₄ che soddisfano una versione in forma debole delle equazioni di Killing. Ciò suggerisce una naturale interpretazione di questi campi come generatori infinitesimi di rotazioni spaziali e traslazioni temporali relative all'osservatore assegnato. Dimostriamo anche che la definizione dei campiM₍₎, ₍₀₎ è matematicamente equivalente alla scelta di un parametro affine privilegiato f lungo le curve di, che gioca il ruolo di distanza ritardata dall'osservatore. Successivamente si esaminano i legami tra f ed altre possibili definizioni di distanza in grande.

---

---

Work performed in the sphere of activity of: Gruppo Nazionale per la Fisica Matematica del CNR.     

On the prediction of riblet performance with engineering turbulence models

The paper reports the outcome of a numerical study of fully developed flow through a plane channel composed of ribleted surfaces adopting a two-equation turbulence model to describe turbulent mixing. Three families of riblets have been examined: idealized blade-type, V-groove and a novel U-form that, according to computations, achieves a superior performance to that of the commercial V-groove configuration. The maximum drag reduction attained for any particular geometry is broadly in accord with experiment though this optimum occurs for considerably larger riblet heights than measurements indicate. Further explorations bring out a substantial sensitivity in the level of drag reduction to the channel Reynolds number below values of 15 000 as well as to the thickness of the blade riblet. The latter is in accord with the trends of very recent, independent experimental studies.Possible shortcomings in the model of turbulence are discussed particularly with reference to the absence of any turbulence-driven secondary motions when an isotropic turbulent viscosity is adopted. For illustration, results are obtained for the case where a stress transport turbulence model is adopted above the riblet crests, an elaboration that leads to the formation of a plausible secondary motion sweeping high momentum fluid towards the wall close to the riblet and thereby raising momentum transport.Nomenclature c _f Skin friction coefficient - c _f Skin friction coefficient in smooth channel at the same Reynolds number - k Turbulent kinetic energy - K ⁺ k/ _w - h Riblet height - S Riblet width - H Half height of channel - Re Reynolds number = volume flow/unit width/ - Modified turbulent Reynolds number - R _t turbulent Reynolds numberk ²/ - P _k Shear production rate ofk, _t (U _i /x _j + U _j /x _i ) U _i /x _j - dP/dz Streamwise static pressure gradient - U _i Mean velocity vector (tensor notation) - U Friction velocity, _w/ where _w=–H dP/dz - W Mean velocity - W _b Bulk mean velocity through channel - y ⁺ yU /v. Unless otherwise stated, origin is at wall on trough plane of symmetry - Kinematic viscosity - _t Turbulent kinematic viscosity - Turbulence energy dissipation rate - Modified dissipation rate – 2(k ^1/2/x _j )² - Density - _k , Effective turbulent Prandtl numbers for diffusion ofk and      

Mixed convection on vertical plate for fluids of any prandtl number

A mixed convection parameter=(Ra) ^1/4/(Re)^1/2, with=Pr/(1+Pr) and=Pr/(1 +Pr)^1/2, is proposed to replace the conventional Richardson number, Gr/Re², for combined forced and free convection flow on an isothermal vertical plate. This parameter can readily be reduced to the controlling parameters for the relative importance of the forced and the free convection,Ra ^1/4/(Re ^1/2 Pr ^1/3) forPr 1, and (RaPr)^1/2/(RePr ^1/2 forPr 1. Furthermore, new coordinates and dependent variables are properly defined in terms of, so that the transformed nonsimilar boundary-layer equations give numerical solutions that are uniformly valid over the entire range of mixed convection intensity from forced convection limit to free convection limit for fluids of any Prandtl number from 0.001 to 10,000. The effects of mixed convection intensity and the Prandtl number on the velocity profiles, the temperature profiles, the wall friction, and the heat transfer rate are illustrated for both cases of buoyancy assisting and opposing flow conditions.

---

Mischkonvektion an einer vertikalen Platte für Fluide beliebiger Prandtl-Zahl

Zusammenfassung Für die kombinierte Zwangs- und freie Konvektion an einer isothermen senkrechten Platte wird ein Mischkonvektions-Parameter=( Ra) ^1/4 (Re)^1/2, mit=Pr/(1 +Pr) und=Pr/(1 +Pr)^1/2 vorgeschlagen, den die gebräuchliche Richardson-Zahl, Gr/Re², ersetzen soll. Dieser Parameter kann ohne weiteres auf die maßgebenden Kennzahlen für den relativen Einfluß der erzwungenen und der freien Konvektion reduziert werden,Ra ^1/4/(Re ^1/2 Pr ^1/3) fürPr 1 und (RaPr)^1/4/(RePr)^1/2 fürPr 1. Weiterhin werden neue Koordinaten und abhängige Variablen als Funktion von definiert, so daß für die transformierten Grenzschichtgleichungen numerische Lösungen erstellt werden können, die über den gesamten Bereich der Mischkonvektion, von der freien Konvektion bis zur Zwangskonvektion, für Fluide jeglicher Prandtl-Zahl von 0.001 bis 10.000 gleichmäßig gültig sind. Der Einfluß der Intensität der Mischkonvektion und der Prandtl-Zahl auf die Geschwindigkeitsprofile, die Temperaturprofile, die Wandreibung und den Wärmeübergangskoeffizienten werden für die beiden Fälle der Strömung in und entgegengesetzt zur Schwerkraftrichtung dargestellt.

---

Nomenclature C _f local friction coefficient - C _p specific heat capacity - f reduced stream function - g gravitational acceleration - Gr local Grashoff number,g T _w –T )x³/v² - Nu local Nusselt number - Pr Prandtl number,v/ - Ra local Rayleigh number,g T _w –T x ³/( v) - Re local Reynolds number,u x/v - Ri Richardson number,Gr/Re ² - T fluid temperature - T _w wall temperature - T free stream temperature - u velocity component in thex direction - u free stream velocity - v velocity component in they direction - x vertical coordinate measuring from the leading edge - y horizontal coordinate Greek symbols thermal diffusivity - thermal expansion coefficient - mixed convection parameter (Ra)1/4/Re)^1/2 - pseudo-similarity variable,(y/x) - ₀ conventional similarity variable,(y/x)Re ^1/2 - dimensionless temperature, (T–T T _W –T - unified mixed-flow parameter, [(Re) ^1/2 + (Ra)^1/4] - dynamic viscosity - kinematic viscosity - stretched streamwise coordinate or mixed convection parameter, [1 + (Re)^1/2/(Ra) ^1/4]^–1=/(1 +) - density - Pr/(1 + Pr) _w wall shear stress - stream function - Pr/(l+Pr)^1/3 This research was supported by a grand from the National Science Council of ROC     

On the closure problem for Darcy's law

In a previous derivation of Darcy's law, the closure problem was presented in terms of an integro-differential equation for a second-order tensor. In this paper, we show that the closure problem can be transformed to a set of Stokes-like equations and we compare solutions of these equations with experimental data. The computational advantages of the transformed closure problem are considerable.Roman Letters A interfacial area of the- interface contained within the macroscopic system, m² - A _e area of entrances and exits for the-phase contained within the macroscopic system, m² - A interfacial area of the- interface contained within the averaging volume, m² - A _e area of entrances and exits for the-phase contained within the averaging volume, m² - B second-order tensor used to respresent the velocity deviation - b vector used to represent the pressure deviation, m^–1 - C second-order tensor related to the permeability tensor, m^–2 - D second-order tensor used to represent the velocity deviation, m² - d vector used to represent the pressure deviation, m - g gravity vector, m/s² - I unit tensor - K C ^–1,–D, Darcy's law permeability tensor, m² - L characteristic length scale for volume averaged quantities, m - characteristic length scale for the-phase, m - l _i i=1, 2, 3, lattice vectors, m - n unit normal vector pointing from the-phase toward the-phase - n _e outwardly directed unit normal vector at the entrances and exits of the-phase - p pressure in the-phase, N/m ² - p intrinsic phase average pressure, N/m² - p –p , spatial deviation of the pressure in the-phase, N/m² - r position vector locating points in the-phase, m - r ₀ radius of the averaging volume, m - t time, s - v velocity vector in the-phase, m/s - v intrinsic phase average velocity in the-phase, m/s - v phase average or Darcy velocity in the \-phase, m/s - v –v , spatial deviation of the velocity in the-phase m/s - V averaging volume, m³ - V volume of the-phase contained in the averaging volume, m³ Greek Letters V /V volume fraction of the-phase - mass density of the-phase, kg/m³ - viscosity of the-phase, Nt/m²     

Chaos and integrability in a nonlinear wave equation

We consider the parametrized family of equations _tt ,u- _xx u-au+u ₂ ² u=O,x(0,L), with Dirichlet boundary conditions. This equation has finite-dimensional invariant manifolds of solutions. Studying the reduced equation to a four-dimensional manifold, we prove the existence of transversal homoclinic orbits to periodic solutions and of invariant sets with chaotic dynamics, provided that =2, 3, 4,.... For =1 we prove the existence of infinitely many first integrals pairwise in involution.     

Free convection heat transfer from an isothermal plate with arbitrary inclination

This paper presents a new formulation for the laminar free convection from an arbitrarily inclined isothermal plate to fluids of any Prandtl number between 0.001 and infinity. A novel inclination parameter is proposed such that all cases of the horizontal, inclined and vertical plates can be described by a single set of transformed equations. Moreover, the self-similar equations for the limiting cases of the horizontal and vertical plates are recovered from the transformed equations by setting=0 and=1, respectively. Heated upward-facing plates with positive and negative inclination angles are investigated. A very accurate correlation equation of the local Nusselt number is developed for arbitrary inclination angle and for 0.001 Pr .

---

Wärmeübertragung bei freier Konvektion an einer isothermen Platte mit beliebiger Neigung

Zusammenfasssung Diese Untersuchung stellt eine neue Formulierung der laminaren freien Konvektion von Flüssigkeiten mit einer Prandtl-Zahl zwischen 0,001 und unendlich an einer beliebig schräggestellten isothermen Platte dar. Ein neuer Neigungsparameter wird eingeführt, so daß alle Fälle der horizontalen, geneigten oder vertikalen Platte von einem einzigen Satz transformierter Gleichungen beschrieben werden können. Die unabhängigen Gleichungen für die beiden Fälle der horizontalen and vertikalen Platte wurden für=0 und=1 aus den transformierten Gleichungen wieder abgeleitet. Es wurden erwärmte aufwärtsgerichtete Platten mit positiven und negativen Neigungswinkeln untersucht. Eine sehr genaue Gleichung wurde für die lokale Nusselt-Zahl bei beliebigen Neigungswinkeln und für 0,001 Pr entwickelt.

---

Nomenclature C _p specific heat - f reduced stream function - g gravitational acceleration - Gr local Grashof number,g(T _w –T _w ) x³/v² - h local heat transfer coefficient - k thermal conductivity - n constant exponent - Nu local Nusselt number,hx/k - p pressure - Pr Prandtl number, v/ - Ra local Rayleigh number,g(T _w –T )J x³/v - T fluid temperature - T _w wall temperature - T temperature of ambient fluid - u velocity component in x-direction - v velocity component in y-direction - x coordinate parallel to the plate - y coordinate normal to the plate Greek symbols thermal diffusivity - thermal expansion coefficient - (Ra¦sin¦)^1/4/( Ra cos()^1/5 - pseudo-similarity variable, (y/) - dimensionless temperature, (T–T )/(T _w–T ) - ( Ra cos)^1/5+(Rasin)^1/4 - v kinematic viscosity - 1/[1 +(Ra cos)^1/5/( Ra¦sin)^1/4] - density of fluid - Pr/(1+Pr) - _w wall shear stress - angle of plate inclination measured from the horizontal - stream function - dimensionless dynamic pressure     

Evaluation of the dynamic-mechanical properties of solids from a cooperative model for stress relaxation

For many solid materials the stress relaxation process obeys the universal relationF = – (d/d lnt)_max = (0.1 ± 0.01) ( ₀ — _i ), regardless of the structure of the material. Here denotes the stress,t the time, ₀ the initial stress of the experiment and _i the internal stress. A cooperative model accounting for the similarity in relaxation behaviour between different materials was developed earlier. Since this model has a spectral character, the concepts of linear viscoelasticity are used here to evaluate the corresponding prediction of the dynamic mechanical properties, i.e. the frequency dependence of the storageE () and lossE () moduli. Useful numerical approximations ofE () andE () are also evaluated. It is noted that the universal relation in stress relaxation had a counterpart in the frequency dependence ofE (). The theoretical prediction of the loss factor for high-density polyethylene is compared with experimental results. The agreement is good.     

On the cross-effects of coupled macroscopic transport equations in porous media

In this paper, the derivation of macroscopic transport equations for this cases of simultaneous heat and water, chemical and water or electrical and water fluxes in porous media is presented. Based on themicro-macro passage using the method of homogenization of periodic structures, it is shown that the resulting macroscopic equations reveal zero-valued cross-coupling effects for the case of heat and water transport as well as chemical and water transport. In the case of electrical and water transport, a nonsymmetrical coupling was found.Notations b mobility - c concentration of a chemical - D rate of deformation tensor - D molecular diffusion coefficient - D _ij ^eff macroscopic (or effective) diffusion tensor - electric field - E ₀ initial electric field - k _ij molecular tensor - j, j ^*, current densities - K _ij macroscopic permeability tensor - l characteristic length of the ERV or the periodic cell - L characteristic macroscopic length - L _ijkl coupled flows coefficients - n _i unit outward vector normal to - p pressure - q _t ,q _t ⁺ , heat fluxes - q _c ,q _c ⁺ , chemical fluxes - s specific entropy or the entropy density - S entropy per unit volume - t time variable - t _ij local tensor - T absolute temperature - v _i velocity - V ₀ initial electric potential - V electric potential - x macroscopic (or slow) space variable - y microscopic (or fast) space variable - _i local vectorial field - _i local vectorial field - electric charge density on the solid surface - , bulk and shear viscosities of the fluid - _ij local tensor - _ij local tensor - _i local vector - _ij molecular conductivity tensor - _ij ^eff effective conductivity tensor - homogenization parameter - fluid density - ₀ ion-conductivity of fluid - _ij dielectric tensor - _i ¹ , _i ² , _i ³ local vectors - ⁴ local scalar - _S solid volume in the periodic cell - _L volume of pores in the periodic cell - boundary between _S and _L - ^s rate of entropy production per unit volume - total volume of the periodic cell - _l volume of pores in the cell On leave from the Politechnika Gdanska; ul. Majakowskiego 11/12, 80-952, Gdask, Poland.     

Flow in porous media III: Deformable media

Stokes flow in a deformable medium is considered in terms of an isotropic, linearly elastic solid matrix. The analysis is restricted to steady forms of the momentum equations and small deformation of the solid phase. Darcy's law can be used to determine the motion of the fluid phase; however, the determination of the Darcy's law permeability tensor represents part of the closure problem in which the position of the fluid-solid interface must be determined.Roman Letters A interfacial area of the- interface contained within the macroscopic system, m² - A interfacial area of the- interface contained within the averaging volume, m² - A _e area of entrances and exits for the-phase contained within the macroscopic system, m² - A ^* interfacial area of the- interface contained within a unit cell, m² - A _e ^* area of entrances and exits for the-phase contained within a unit cell, m² - E Young's modulus for the-phase, N/m² - e i unit base vectors (i = 1, 2, 3) - g gravity vector, m²/s - H height of elastic, porous bed, m - k unit base vector (=e ₃) - characteristic length scale for the-phase, m - L characteristic length scale for volume-averaged quantities, m - n unit normal vector pointing from the-phase toward the-phase (n = -n ) - p pressure in the-phase, N/m² - P p – g·r, N/m² - r ₀ radius of the averaging volume, m - r position vector, m - t time, s - T total stress tensor in the-phase, N/m² - T ⁰ hydrostatic stress tensor for the-phase, N/m² - u displacement vector for the-phase, m - V averaging volume, m₃ - V volume of the-phase contained within the averaging volume, m³ - v velocity vector for the-phase, m/s Greek Letters V /V, volume fraction of the-phase - mass density of the-phase, kg/m³ - shear coefficient of viscosity for the-phase, Nt/m² - first Lamé coefficient for the-phase, N/m² - second Lamé coefficient for the-phase, N/m² - bulk coefficient of viscosity for the-phase, Nt/m² - T –T ⁰ , a deviatoric stress tensor for the-phase, N/m²     

Stability criterion for steady-state burning of powders

A model of a powder with a variable surface temperature is considered. A stability criterion for the steady-state burning of powders at constant pressure is found on the assumption that all the processes in the gas phase and the reaction layer of the condensed phase are inertialess. It is shown that the stability region is determined by two parameters: K=(T₁ – t₀) ( ln m/T₀)p and r=(T₁/T₀)p (here T₁ is the surface temperature, T₁ is the initial temperature of the powder, m is the mass burning rate, p is pressure). Burning is always stable if < 1. If > 1, the burning process is stable only when r > ( – 1)²/ / + 1.The author expresses his appreciation to A. S. Kompaneits, O. I. Leipunskii, A. G. Istratov, V. B. Librovich, and S. S. Novikov for discussing his work.     

Transport in ordered and disordered porous media II: Generalized volume averaging

In this paper we develop the averaged form of the Stokes equations in terms of weighting functions. The analysis clearly indicates at what point one must choose a media-specific weighting function in order to achieve spatially smoothed transport equations. The form of the weighting function that produces the cellular average is derived, and some important geometrical theorems are presented.Roman Letters A interfacial area of the- interface associated with the local closure problem, m² - A _e area of entrances and exits for the-phase contained within the averaging system, m² - A _p surface area of a particle, m² - d _p 6V _p/A_p, effective particle diameter, m - g gravity vector, m/s² - I unit tensor - K _m permeability tensor for the weighted average form of Darcy's law, m² - L general characteristic length for volume averaged quantities, m - L _p general characteristic length for volume averaged pressure, m - L characteristic length for the porosity, m - L _v characteristic length for the volume averaged velocity, m - l characteristic length (pore scale) for the-phase - l _i i=1, 2, 3 lattice vectors, m - (y) weighting function - m(–y) (y), convolution product weighting function - _v special weighting function associated with the traditional averaging volume - m _v special convolution product weighting function associated with the traditional averaging volume - m _g general convolution product weighting function - m _V unit cell convolution product weighting function - m _C special convolution product weighting function for ordered media which produces the cellular average - m _D special convolution product weighting function for disordered media - m _M master convolution product weighting function for ordered and disordered media - n unit normal vector pointing from the-phase toward the-phase - p pressure in the-phase, N/m² - p_m superficial weighted average pressure, N/m² - p _m intrinsic weighted average pressure, N/m² - p traditional intrinsic volume averaged pressure, N/m² - p p p _m , spatial deviation pressure, N/m² - r ₀ radius of a spherical averaging volume, m - r _m support of the convolution product weighting function, m - r position vector, m - r position vector locating points in the-phase, m - V averaging volume, m³ - V volume of the-phase contained in the averaging volume, m³ - V _cell volume of a unit cell, m³ - V velocity vector in the-phase, m/s - vm superficial weighted average velocity, m/s - v _m intrinsic weighted average velocity, m/s - V volume of the-phase contained in the averaging volume, m³ - V _p volume of a particle, m³ - v traditional superficial volume averaged velocity, m/s - v v p _m spatial deviation velocity, m/s - x position vector locating the centroid of the averaging volume or the convolution product weighting function, m - y position vector relative to the centroid, m - y position vector locating points in the-phase relative to the centroid, m Greek Letters indicator function for the-phase - Dirac distribution associated with the- interface - V /V, volume average porosity - _m m * . weighted average porosity - mass density of the-phase, kg/m³ - viscosity of the-phase, Ns/m² - V /V, volume fraction of the-phase     

Transport in ordered and disordered porous media IV: Computer generated porous media for three-dimensional systems

In the method of volume averaging, the difference between ordered and disordered porous media appears at two distinct points in the analysis, i.e. in the process of spatial smoothing and in the closure problem. In theclosure problem, the use of spatially periodic boundary conditions isconsistent with ordered porous media and the fields under consideration when the length-scale constraint,r ₀L is satisfied. For disordered porous media, spatially periodic boundary conditions are an approximation in need of further study.In theprocess of spatial smoothing, average quantities must be removed from area and volume integrals in order to extractlocal transport equations fromnonlocal equations. This leads to a series of geometrical integrals that need to be evaluated. In Part II we indicated that these integrals were constants for ordered porous media provided that the weighting function used in the averaging process contained thecellular average. We also indicated that these integrals were constrained by certain order of magnitude estimates for disordered porous media. In this paper we verify these characteristics of the geometrical integrals, and we examine their values for pseudo-periodic and uniformly random systems through the use of computer generated porous media.

Nomenclature

Roman Letters A interfacial area of the- interface associated with the local closure problem, m² - A _e area of entrances and exits for the-phase contained within the averaging system, m² - a _i i=1, 2, 3 gaussian probability distribution used to locate the position of particles - I unit tensor - L general characteristic length for volume averaged quantities, m - L characteristic length for , m - L characteristic length for , m - characteristic length for the -phase particles, m - ⁰ reference characteristic length for the-phase particles, m - characteristic length for the-phase, m - _i i=1, 2, 3 lattice vectors, m - m convolution product weighting function - m _v special convolution product weighting function associated with the traditional volume average - n _i i=1, 2, 3 integers used to locate the position of particles - n unit normal vector pointing from the-phase toward the-phase - n _e outwardly directed unit normal vector at the entrances and exits of the-phase - r _p position vector locating the centroid of a particle, m - r gaussian probability distribution used to determine the size of a particle, m - r ₀ characteristic length of an averaging region, m - r position vector, m - r _m support of the weighting functionm, m - averaging volume, m³ - V volume of the-phase contained in the averaging volume,, m³ - x positional vector locating the centroid of an averaging volume, m - x ₀ reference position vector associated with the centroid of an averaging volume, m - y position vector locating points relative to the centroid, m - y position vector locating points in the-phase relative to the centroid, m Greek Letters indicator function for the-phase - Dirac distribution associated with the- interface - V /V, volume average porosity - /L, small parameter in the method of spatial homogenization - standard deviation ofa _i - _r standard deviation ofr - _r intrinsic phase average of      

Transport in ordered and disordered porous media V: Geometrical results for two-dimensional systems

In this paper we continue the geometrical studies of computer generated two-phase systems that were presented in Part IV. In order to reduce the computational time associated with the previous three-dimensional studies, the calculations presented in this work are restricted to two dimensions. This allows us to explore more thoroughly the influence of the size of the averaging volume and to learn something about the use of anon-representative region in the determination of averaged quantities.

Nomenclature

Roman Letters A interfacial area of the– interface associated with the local closure problem, m² - a _i i=1, 2, gaussian probability distribution used to locate the position of particles - l unit tensor - characteristic length for the-phase particles, m - ⁰ reference characteristic length for the-phase particles, m - characteristic length for the-phase, m - _i i=1,2,3 lattice vectors, m - m convolution product weighting function - m _V special convolution product weighting function associated with a unit cell - n _i i=1, 2 integers used to locate the position of particles - n unit normal vector pointing from the-phase toward the-phase - r _p position vector locating the centroid of a particle, m - r gaussian probability distribution used to determine the size of a particle, m - r ₀ characteristic length of an averaging region, m - V averaging volume, m³ - V volume of the-phase contained in the averaging volume,V, m³ - x position of the centroid of an averaging area, m - x ₀ reference position of the centroid of an averaging area, m - y position vector locating points in the-phase relative to the centroid, m Greek Letters V /V, volume average porosity - _{a i} standard deviation ofa _i - _r standard deviation ofr - intrinsic phase average of      

Electric and thermal conductivity anisotropy of an articulated medium

It is well known that articulation may cause the electric and thermal conducting properties of a medium to become anisotropic. Extensive experimental data relating to the conductivity of rock were presented in [1], and according to these data the ambient resistance in the case of an orderly arrangement of cracks noticeably depends on the direction along which it is measured; an ellipsoid of resistance anisotropy can be constructed from the measurement results. A pronounced correlation between the orientations of the resistivity extrema and the orientation of the crack system is observed here. A comparison betwen the direction rose of the fractures and the direction rose of the articulation carried out for different regions has shown that they are identical. A crack density tensor T describing the average (with respect to a given volume) geometry of the articulation has been introduced [2, 3]. In the current work, it is proved that T can be effectively used in problems involving anisotropic electrical and thermal conductivity. The resistivity tensor and thermal-conductivity coefficient tensor K, which characterize the anisotropy of the electrical and thermal conducting properties, are expressed in terms of t. The structure of this relation is established; the equations presented allow us to find the form of and K if the articulation parameters are known.Translated from Zhurnal Prikladnoi Mekhaniki i Tekhnicheskoi Fiziki, No. 1, pp. 141–144, January–February, 1976.