Factors affecting the reactivity of thiol-functionalized mesoporous silica adsorbents toward mercury(II)

Numerous mercaptopropyl-functionalized silica spheres have been prepared by either post-synthesis grafting of MCM-41 and MCM-48 or self-assembly co-condensation of mercaptopropyltrimethoxysilane (MPTMS) or mercaptopropyltriethoxysilane (MPTES) and tetraethoxysilane (TEOS) precursors in hydroalcoholic medium in the presence of a cationic surfactant as templating agent and ammonia as catalyst. These materials of approximately the same particle size and morphology featured different functionalization levels, various degrees of structural order, and variable distribution of thiol groups in the mesopores. Their reactivity in solution has been studied using Hg(II) as model analyte. Total accessibility (on a 1:1 S:Hg stoichiometry basis) was demonstrated and quantified for well-ordered materials whereas less open and less organized structures with high degrees of functionalization were subject to less-than-complete loadings. Capacities measured at pH 2 were lower than at pH 4 because of distinct mercury-binding mechanisms. Kinetics associated to the uptake process were studied by in situ electrochemical monitoring of Hg(II) consumption from aqueous suspensions containing the various adsorbents. They indicate only little difference between materials of the MCM-41 and MCM-48 series at similar functionalization levels, fast mass transport in well-ordered mesostructures in comparison to the poorly or non-ordered ones (except at pH 2 where charge formation induced some restriction in materials characterized by long-range structural order), and even faster processes in the wormlike frameworks (characterized by shorter range structural order). Hg(II) binding to thiol-functionalized materials obtained by post-synthesis grafting was found to occur more rapidly in the early beginning of the uptake process as a result of a higher concentration of binding sites at the pore entrance in comparison to the more homogeneous distribution of these groups in the mesochannels of materials obtained by co-condensation.     

Amine functionalized MCM-41: An active and reusable catalyst for Knoevenagel condensation reaction

This paper reports preparation, characterization of amine modified mesoporous crystalline MCM-41 and its application in Knoevenagel condensation reaction. Amine modified MCM-41 was prepared by co-condensation and post-synthesis methods. The samples were characterized by X-ray powder diffraction, Fourier-transfer infrared spectroscopy (FTIR), thermo gravimetric analysis (TGA), differential thermal analysis (DTA), scanning electron micrograph (SEM), ²⁹Si magic-angle spinning (MAS), nuclear magnetic resonance (NMR), diffuse reflectance spectra (DRS), nitrogen adsorption–desorption and CHN analysis. X-ray diffraction patterns indicate that the modified materials retain the standard MCM-41 structure. SEM study exhibits that the arrangement of particles for 12.8% amine modified MCM-41 is well ordered and spherical in nature. CHN analysis supports that complete hydrolysis of ethoxy groups take place in 12.8% amine modified sample. From the NMR study it is confirmed that the surface coverage is 40% in 12.8% amine modified sample. The base catalytic activity of hybrid MCM-41 materials such as amine (post-synthesis and co-condensation methods) and surfactant functionalized materials for condensation reaction between benzaldehyde and diethyl malonate in solvent free, room temperature synthesis of cinnamic acid was evaluated and correlated with the surface and textural properties. Sample containing 12.8 wt% amine loaded by co-condensation method showed highest malonic ester conversion (92%) and selectivity (98%) for cinnamic acid.     

Synthesis,characterisation and application of mercapto- and polyaminophenol-bifunctionalised MCM-41 for dispersive micro solid phase extraction of Ni(II) prio to inductively coupled plasma-optical emission spectrometry (DMSPE-ICP-OES)

Highly ordered adsorbent mesoporous silica (MCM-41) was synthesised using a rapid method and its subsequent chemical modification with 3-mercaptopropyltrimethoxysilane (MPTMS) in toluene medium at 60°C was performed. The electro-reduction product of 4-nitrophenol (EP4NP), as a new kind of polyaminophenol-type chelating agent with a high affinity to Ni(II), was then incorporated into MPTMS-MCM-41. The resulting materials (MCM-41, MPTMS-MCM-41 and EP4NP-MPTMS-MCM-41) were characterised by scanning electron microscopy, powder X-ray diffraction, nitrogen gas sorption and Fourier transform-infrared spectrometry. The new modified adsorbent EP4NP-MPTMS-MCM-41 was then employed for preconcentration of ultra-trace amounts of Ni(II) by dispersive micro solid phase extraction prior to inductively coupled plasma-optical emission spectrometry. The effects of variables such as pH, mass of the chelating agent, the amount of EP4NP-MPTMS-MCM-41, stirring time of extraction step, HCl concentration and stirring time during elution were optimised and the calibration curve was plotted. The limits of detection and quantitation were 0.006 and 0.019 μg L^?1, respectively. The mean, standard error and relative standard deviation for five replicates of 0.5 μg L^?1 Ni(II) were calculated to be 0.48 μg L^?1, 4.0% and 3.2%, respectively. The proposed method was successfully applied for determination of Ni(II) in wastewater samples.     

介孔分子筛MCM-48的室温合成与表面修饰

在室温条件下的碱性介质中合成了介孔分子筛MCM-48，并对其进行了有机官能团表面修饰。利用HRTEM、低温N₂吸附、XRD、TG、IR和NMR等手段对产物进行了结构和性能分析。实验结果表明，合成产物MCM-48具有规则的孔道结构、大比表面积、大孔容和窄分布的孔径。由硅烷试剂表面修饰后的MCM-48，由于有机官能团接枝在MCM-48的内表面，占据了孔道内部空间，使其比表面积、孔容和孔径都减小。     

苯官能化MCM-41的合成、表征、磺酰化及与二胺的反应

以三乙氧基硅基苯((C₂H₅O)₃Si-Ph，（(triethoxysilyl)benzene，TESB)以及正硅酸乙酯（TEOS）的混合液为硅源，以溴代十六烷基吡啶(CPBr)为模板剂，在HCl介质中合成了苯官能化的有机-无机杂化介孔分子筛MCM-41。对合成的分子筛用FT-IR、PXRD、TEM、N₂吸附-脱附等手段进行了表征。结果表明，合成的苯官能化的有机-无机杂化介孔分子筛具有良好的介孔孔道结构。用三甲基氯硅烷对分子筛表面的Si-OH进行了封端处理，用氯磺酸对合成的苯官能化的有机-无机杂化介孔分子筛进行了磺酰化，并与各种二胺进行了反应。     

Drug delivery from hydrophobic-modified mesoporous silicas: Control via modification level and site-selective modification

Dimethylsilyl (DMS) modified mesoporous silicas were successfully prepared via co-condensation and post-grafting modification methods. The post-grafting modification was carried out by the reaction of the as-synthesized MCM-41 material (before CTAB removal) with diethoxydimethylsinale (DEDMS). N₂ adsorption-desorption and ²⁹Si MAS NMR characterization demonstrated that different amount of DMS groups were successfully incorporated into the co-condensation modified samples, and the functional DMS groups were placed selectively on the pore openings and external pore surfaces in the post-grafting modified samples. Subsequently, the controlled drug delivery properties from the resulting DMS-modified mesoporous silicas were investigated in detail. The drug adsorption experiments showed that the adsorption capacities were mainly depended on the content of silanol group (CSG) in the corresponding carriers. The in vitro tests exhibited that the incorporation of DMS groups greatly retarded the ibuprofen release rate. Moreover, the ibuprofen release profiles could be well modulated by varying DMS modification levels and site-selective distribution of functional groups in mesoporous carriers.     

Mesoporous micelle templated silica with incorporated C<Subscript>8</Subscript> and C<Subscript>18</Subscript> phase

Mesoporous silica material of MCM-41 type was synthesized by co-condensation of highly concentrated octyltriethoxysilane (OTEOS), octadecyltriethoxysilane (ODTEOS) and tetraethoxysilane (TEOS). The obtained hybrid materials were characterized using XRD, TG-DSC and low temperature adsorption/desorption of nitrogen. It was shown that the applied method of synthesis allows to obtain silica of MCM-41 type with a high degree of hydrocarbon saturation.     

以混合表面活性剂为模板可控合成MCM-48和MCM-41分子筛

利用阳离子和三嵌段共聚物混合表面活性剂为模板,在水热条件、碱性介质中可控合成出MCM-48和MCM-41分子筛。在固定P123(聚氧乙烯-聚氧丙烯-聚氧乙烯三嵌段共聚物):TEOS(正硅酸乙酯)(物质的量的比)为0.01875的体系中,调节CTAB(十六烷基三甲基溴化铵)∶TEOS(正硅酸乙酯)物质的量比值m,当m在0.12~0.13范围合成出MCM-48分子筛;当m在0.04~0.08范围合成出MCM-41分子筛。通过XRD,TEM,N2物理吸附,IR等方法进行了表征。结果表明:聚氧乙烯-聚氧丙烯-聚氧乙烯三嵌段共聚物(P123)的加入可以更大程度地降低合成介孔材料所需阳离子表面活性剂的用量;可控合成的介孔材料具有高比表面积、高度有序的孔道结构、较集中的孔径分布。     

Removal of complexed mercury by dithiocarbamate grafted on mesoporous silica

Mesoporous silica (MCM-41) with d ₍₁₀₀₎ interplanar distance of 38 Å was prepared by a room temperature process through low surfactant templation technique. The surface of MCM-41 was functionalized with dithiocarbamate (dtc) ligand, named as MCM-41-dtc and this was characterized by X-ray diffraction, BET surface area, particle size analysis, ²⁹Si MAS NMR spectra and sulphur analysis. The sorption of mercury from 0.1M HCl solution by MCM-41-dtc was studied as a function of pH, [Hg²⁺], time and temperature. The sorption data obtained at various initial concentrations of mercury were fitted into Langmuir adsorption model. Mercury speciation in solution and the sorption capacity measurements indicated possible formation of a 1 : 1 square planar complex in the solid phase. A very rapid sorption of mercury was observed in the initial stages of equilibration, which can be attributed to the large surface area, wide porosity and fine particle size of MCM-41-dtc, facilitating facile accessibility of mercury into the inner pores of the sorbent. The enthalpy change accompanied by the sorption of mercury was found to decrease from 83.7 to 6.2 kJ/mol, when the initial concentration of mercury was increased from 5^.10^-4M to 1.5^.10^-3M.     

Catalytic Performance of Spherical MCM-41 Modified with Copper and Iron as Catalysts of NH3-SCR Process

Spherical MCM-41 with various copper and iron loadings was prepared by surfactant directed co-condensation method. The obtained samples were characterized with respect to their structure (X-ray diffraction, XRD), texture (N₂ sorption), morphology (scanning electron microscopy, SEM), chemical composition (inductively coupled plasma optical emission spectrometry, ICP-OES), surface acidity (temperature programmed desorption of ammonia, NH₃-TPD), form, and aggregation of iron and copper species (diffuse reflectance UV-Vis spectroscopy, UV-Vis DRS) as well as their reducibility (temperature programmed reduction with hydrogen, H₂-TPR). The spherical MCM-41 samples modified with transition metals were tested as catalysts of selective catalytic reduction of NO with ammonia (NH₃-SCR). Copper containing catalysts presented high catalytic activity at low-temperature NH₃-SCR with a very high selectivity to nitrogen, which is desired reaction products. Similar results were obtained for iron containing catalysts, however in this case the loadings and forms of iron incorporated into silica samples very strongly influenced catalytic performance of the studied samples. The efficiency of the NH₃-SCR process at higher temperatures was significantly limited by the side reaction of direct ammonia oxidation. The reactivity of ammonia molecules chemisorbed on the catalysts surface in NO reduction (NH₃-SCR) and their selective oxidation (NH₃-SCO) was verified by temperature-programmed surface reactions.     

共缩聚法制备有序介孔氧化硅纳米螺旋纤维

在传统球状介孔氧化硅合成工作的基础上,以正硅酸乙(TEOS)和γ-巯丙基三甲氧基硅烷(MPTMS)为硅源,在水体系下利用共缩聚法一步合成出具有介孔分子筛结构特征的纳米纤维,并通过扫描电子显微镜(SEM)、小角X射线衍(XRD)、透射电子显微镜(TEM)和氮气吸附-脱附实验对样品进行了表征与分析.     

Preparation,characterization, and hydrogenation activity of new Rh0–MCM-41 catalysts prepared from as-synthesized MCM-41 and RhCl3

Impregnation of as-synthesized MCM-41 silica by ethanolic solutions of rhodium(III) chloride was tested as an alternative to its introduction into the synthesis gel to get, after calcination and reduction by H₂, highly dispersed metal(0) nanoparticles throughout the mesopores network. Rh(III) and Rh(0)–based solids thus obtained were analyzed by infrared spectroscopy, elemental analysis, transmission electron microscopy, N₂ sorption, and X-ray diffraction. Materials with 1.6 wt % of rhodium could be obtained as a result of CTA⁺/Rh³⁺ exchange. The determining role of CTA⁺ was emphasized through blank experiments. In a second series of materials, ethanol was also exploited for its ability to reduce Rh(III). All Rh(0)-based solids were tested as catalysts in the hydrogenation of styrene under mild temperature and pressure conditions. Catalysis performances of the most efficient sample (reduced by H₂) were further compared with those of a very similar material prepared by the introduction of Rh(III) directly into the synthesis gel of MCM-41 silica. Better cis selectivities in the hydrogenation of disubstituted arene derivatives were achieved with materials issued from the new preparation method.     

Spherical Al-MCM-41 Doped with Copper by Modified TIE Method as Effective Catalyst for Low-Temperature NH3-SCR

Aluminum containing silica spherical MCM-41 was synthesized and modified with copper by the template ion-exchange method (TIE) and its modified version, including treatment of the samples with ammonia solution directly after template ion-exchange (TIE-NH₃). The obtained samples were characterized with respect to their chemical composition (ICP-OES), structure (XRD), texture (low temperature N₂ sorption), morphology (SEM-EDS), form and aggregation of deposited copper species (UV-vis DRS), reducibility of copper species (H₂-TPR), and surface acidity (NH₃-TPD). The deposition of copper by the TIE-NH₃ method resulted in much better dispersion of this metal on the MCM-41 surface comparing to copper introduced by TIE method. It was shown that such highly dispersed copper species, mainly monomeric Cu²⁺ cations, deposited on aluminum containing silica spheres of MCM-41, are significantly more catalytically effective in the NH₃-SCR process than analogous catalysts containing aggregated copper oxide species. The catalysts obtained by the TIE-NH₃ method effectively operated in much broader temperature and were less active in the side process of direct ammonia oxidation by oxygen.     

MCM-41分子筛的合成及129Xe核磁共振的研究

Purely siliceous MCM-41 with a narrow pore-size distribution, different pore size, high surface area was synthesized . As prepared, calcined and catalytically tested MCM-41 materials have been comprehensively characterized by N₂ adsorption/desorption at 77K and ¹²⁹Xe NMR. By adding mesitylene during the synthesis, the pore size of MCM-41 was enlarged to 5.2nm. The chemical shift in ¹²⁹Xe NMR spectroscopy of adsorbed xenon indicates that the MCM-41 is one dimensional pore channels .     

Ion-exchange properties and electrochemical characterization of quaternary ammonium-functionalized silica microspheres obtained by the surfactant template route

Porous silica spheres functionalized with quaternary ammonium groups have been prepared by co-condensation of N-((trimethoxysilyl)propyl)-N,N,N-trimethylammonium chloride (TMTMAC) and tetraethoxysilane (TEOS) in the presence of cetyltrimethylammonium as a template and ammonia as a catalyst. The physicochemical characteristics of the resulting ion exchangers have been analyzed by various techniques and discussed with respect to the amount of organofunctional groups in the materials. For comparison purposes, both an ordered MCM-41 type mesoporous silica and two silica gels of different pore size have been grafted with TMTMAC. The ion-exchange capabilities were first evaluated from batch experiments (determination of anion-exchange capacities) and then by ion-exchange voltammetry at carbon paste electrodes modified with these hybrid materials. Effective concentration of Fe(CN)(6)(3)(-) species in the anion exchangers was pointed out, while no significant accumulation of Ru(NH(3))(6)(3+) was observed. The preconcentration efficiency was discussed on the basis of the organic group content in the materials as well as their structure and porosity. A second series of materials displaying zwitterionic surfaces was finally prepared and characterized with respect to their physicochemical properties and ion-exchange voltammetric behavior. They consisted of sulfonic acid-functionalized mesoporous silica samples resulting from the oxidation of thiol-functionalized silica spheres obtained by co-condensation of mercaptopropyl-trimethoxysilane (MPTMS) and TEOS, which were then grafted with TMTMAC at various functionalization levels. Possible interactions between the ammonium and sulfonate moieties in the confined medium were pointed out from X-ray photoelectron spectroscopy. The competitive accumulation-rejection of Fe(CN)(6)(3)(-) and Ru(NH(3))(6)(3+) redox probes was finally studied by cyclic voltammetry.     

Synthesis of Thermally Stable MCM-41 at Ambient Temperature

A new process to synthesize thermally stable mesoporous molecular sieves of MCM-41 structure based on delayed neutralization at ambient temperature was investigated. All samples synthesized by this new method have BET surface areas of about 1100m²/g and possess high thermal stability up to 900°C. Higher crystallinity and less lattice constriction after calcination were observed for samples with a longer aging period. Those samples with aging time longer than 10 days exhibited four characteristic XRD peaks of MCM-41 both before and after calcination at 560°C. The N₂ adsorption-desorption isotherms of the calcined samples showed larger average pore size and more homogenous pore size distribution. The method was also successfully applied to the synthesis of MCM-41 with different surfactants of hydrocarbon length with 10–18 carbons and proves to be a simple route for obtaining thermally stable MCM-41 at room temperature.     

Heteropolyacid (H3PW12O40) supported MCM-41: An efficient solid acid catalyst for the green synthesis of xanthenedione derivatives

HPWA/MCM-41 mesoporous molecular sieves of appropriate ratios were prepared by loading HPWA on siliceous MCM-41 by the wet impregnation method. The prepared HPWA/MCM-41 materials were characterized by X-ray diffraction analysis (XRD) and BET surface area and FT-IR measurements. The morphology of mesoporous materials was studied by TEM observation. The catalytic activity of the above materials was tested for the condensation of dimedone (active methylene carbonyl compound) and various aromatic aldehyes under liquid phase conditions at 90 °C. The products were confirmed by FT-IR, ¹H NMR and ¹³C NMR studies. HPWA supported MCM-41 catalysts catalyses efficiently the condensation of dimedone and aromatic aldehydes in ethanol and other solvents under liquid phase conditions to afford the corresponding xanthenedione derivatives. Activities of the catalysts follow the order: HPWA/MCM-41(20 wt.%) > HPWA/MCM-41(30 wt.%) > H₃PW₁₂O₄₀·nH₂O > HPWA/MCM-41(10 wt.%) > HPWA/SiO₂ (20 wt.%) > HM (12) > Hβ (8) > Al-MCM-41 (50). Various advantages associated with these protocols include simple workup procedure, short reaction times, high product yields and easy recovery and reusability of the catalyst.     

Preparation of MnCo/MCM-41 catalysts with high performance for chlorobenzene combustion

MCM-41 was synthesized by a soft template technique. The specific surface area and pore volume of the MCM-41 were 805.9 m²/g and 0.795 cm³/g, respectively. MCM-41-supported manganese and cobalt oxide catalysts were prepared by an impregnation method. The energy dispersive X-ray spectroscopy clearly confirmed the existence of Mn, Co, and O, which indicated the successful loading of the active components on the surface of MCM-41. The structure and function of the catalysts were changed by modulating the molar ratio of manganese to cobalt. The 10%MnCo(6:1)/MCM-41 (Mn/Co molar ratio is 6:1) catalyst displayed the best catalytic activity according to the activity evaluation experiments, and chlorobenzene (1000 ppm) was totally decomposed at 270 °C. The high activity correlated with a high dispersion of the oxides and was attributed to the exposure of more active sites, which was demonstrated by X-ray diffraction and high-resolution transmission electron microscopy. The strong interactions between MnO₂, Co₃O₄, MnCoO_x, and MCM-41 indicated that cobalt promoted the redox cycles of the manganese system. The bimetal-oxide-based catalyst showed better catalytic activity than that of the single metal oxide catalysts, which was further confirmed by H₂ temperature-programmed reduction. Chlorobenzene temperature-programmed desorption results showed that 10%MnCo(6:1)/MCM-41 had higher adsorption strength for chlorobenzene than that of single metal catalysts. And stronger adsorption was beneficial for combustion of chlorobenzene. Furthermore, 10%MnCo(6:1)/MCM-41 was not deactivated during a continuous reaction for 1000 h at 260 °C and displayed good resistance to water and benzene, which indicated that the catalyst could be used in a wide range of applications.     

Thermal degradation of CTAB in as-synthesized MCM-41

Thermal evacuation of a surfactant template from pure siliceous MCM-41 and MCM-41 containing aluminium in hydrogen flow was investigated. Micelle templated MCM-41 were prepared using hexadecyltrimethylammonium bromide (CTAB). The products of thermal surfactant degradation outside and inside pores were identified at various temperatures using ¹³C solid-state nuclear magnetic resonance (NMR) spectroscopy, gas chromatography coupled with mass spectrometer (GC-MS) and temperature programmed desorption coupled with mass spectrometer (TPD-MS). The GC-MS and ¹³C MAS NMR results obtained from this study provide an insight into the mechanism of surfactant transformation during MCM-41 synthesis on molecular level.     

Pd/NH2C3H6-MCM-41催化水介质中的碘苯Ullmann反应

 采用室温共缩聚法合成了胺基改性MCM-41杂化材料(NH2C3H6-MCM-41), 并以此材料为载体制备了负载型Pd催化剂 (Pd/NH2C3H6-MCM-41). 采用X射线衍射、核磁共振、红外光谱、透射电镜、X射线光电子能谱和N2吸附等方法对催化剂进行了表征. 结果表明,催化剂仍保持有MCM-41的孔结构,但其有序度随着 NH2C3H6-基团和Pd含量的增加而降低. 催化剂在以水为溶剂的碘苯偶联反应(Ullmann反应)中显示出优良的催化性能,联苯收率可达63%, 有望为清洁有机合成提供高效非均相催化剂. 胺基修饰的促进作用可归因于催化剂Pd分散度的提高和表面化学性质的改变.