聚丙烯共混物反应挤出过程中的降解抑制

聚丙烯／（丙烯腈－苯乙烯）共聚物在过氧化二异丙苯存在下反应共混挤出时，加入亚油酸三甘酯可以有效地抑制过程的降解，从挤出物中分离出聚丙烯组分测试熔体流动速率表明，加入亚油酸三甘酯后，其熔体流动速率有很大下降，扫描电子显微镜的观察表明，调节过氧化二异丙苯和亚油酸三甘酯的加入量，可有效控制降解并生成较多的接枝物相容性，显著改善相形态。     

γ—射线辐照对HIPS／SBS共混物结构与性能的影响

采用＾６０Ｃｏγ－射线对ＨＩＰＳ／ＳＢＳ共混物以不同剂量和时间进行辐照，适当条件，可改善共混物的性能，其中的丁二烯橡胶相可产生不同程度的交联，使抗张强度，弹性模量增加，热变形温度及硬度明显提高，并观察了交联后形态结构的变化。     

γ－射线辐照对HIPS／SBS共混物结构与性能的影响

采用６０Ｃｏγ－射线对ＨＩＰＳ／ＳＢＳ共混物以不同剂量和时间进行辐照，适当条件下，可改善共混物的性能，其中的丁二烯橡胶相可产生不同程度的交联，使抗张强度、弹性模量增加，热变形温度及硬度明显提高。并观察了交联后形态结构的变化。     

聚氯乙烯—丁腈橡胶—氯丁橡胶三元共混物的研究

测定了聚氯乙烯（ＰＶＣ）－丁脯橡胶（ＮＢＲ－２９）－氯丁橡胶（ＣＲ）三元共混物的冲击性能和应力－应变行为，用动态力分析、扫描电和透射电镜研究了共混物的相容性和形态结构。结果表明，ＮＢＲ－２９对ＰＶＣ，ＣＲ有良好的增容作用，三元共混物是部分相容的二相体系，具有良好的抗冲击性能。     

EAA增容LLDPE／SAN共混物的形态及力学性能

采用SEM及力学性能测试等方法，研究了乙烯－丙烯酸共聚物（EAA）含量对其增容线性低密度聚乙烯（LLDPE）／苯乙烯－丙烯腈共聚物（SAN）共混物形态及性能的影响．发现少量的EAA可使共混物中SAN相的相尺寸减小，共混物模量、拉伸强度及断裂伸长率提高．当EAA的含量增加至11．7％时，它在共混物中两相界而的分布达到饱和，即增容剂饱和浓度Cs=11．7％；此时，共混物形态及性能的变化趋势出现明显转折．明显过量的EAA主要起增韧作用．EAA的增容机理为，它与LLDPE组分的非晶区可部分相容，同时又与SAN相存在着分子间特殊作用.     

三氯化铁对聚丙烯光氧化降解的作用

用红外及紫外光谱法研究了三氯化铁(FeCl₃)对聚丙烯(PP)光氧化降解的影响。实验结果表明,FeCl₃对聚丙烯光氧化有显著的促进作用,但促进作用与FcCl₃含量之间不成线性关系,存在一促进作用的极大值(在本实验条件下,FeCl₃含量为0.5%时,促进作用最大)。实验还表明,FeCl₃的作用可能包含了通过光解产生自由基引发PP光氧化反应、催化分解氢过氧化物以及光屏蔽等几种作用。根据FeCl₃的作用机理,解释了FeCl₃对PP光氧化降解的促进作用与其含量的依赖关系中存在的极位现象。     

聚丙烯／氯化聚乙烯共混物的形态结构

 用透射电子显微镜方法研究了聚丙烯（ｉＰＰ）和氯化聚乙烯（ＣＰＥ）共混物溶液浇铸膜的形态结构．共混物中ＣＰＥ含量≤７０％时不妨碍ｉＰＰ球晶两种结构（交叉结构和条状结构）区域的生成．在ＣＰＥ含量≥８０％时，分散相ｉＰＰ形成近乎直角（８０°）交叉的稀疏的片晶网络．在共混物的全组成范围内，ＣＰＥ结晶在ｉＰＰ片晶上附生生长，二者结晶Ｃ轴的交角为５０°     

增容聚苯乙烯共混物的研究进展

综述了增容聚苯乙烯与聚乙烯、聚丙烯、聚酰胺共混物的研究进展。不同共混物采用不同的增容剂,可使增容聚苯乙烯共混物改善分散相尺寸、界面相互作用与粘结,达到提高共混物的力学性能的目的。增容效果与增容剂的类型、用量和分子结构有关。     

聚合物共混物相容性的研究进展

相容性聚合物共混物由于其优异的复合性能已成为新材料的主要研究方向。但许多共混物是互不相容的 ,因此必须改善它们的相容性。文章综述了聚合物共混物相容性研究的现状与发展 ,介绍了各种增容方法及其应用     

PMMA-PEO共混体系的辐射交联

<正> 聚甲基丙烯酸甲酯(PMMA)是典型的辐射裂解型聚合物。经辐照后,PMMA主链发生无规断裂。在聚合物共混体系中,PMMA是否能发生交联,这是辐射化学中一个非常重要的研究课题之一,也是一项探索性工作。 PMMA-PEO共混体系是可以分子水平共溶的体系。本文试图将共混体系的相容性与共混体系中的裂解型聚合物的辐射效应联系起来,讨论PMMA-PEO共混体系的辐射交联。     

MONTE CARLO SIMULATION OF TRIBLOCK COPOLYMER/HOMOPOLYMER BLEND FILMS

The morphologies of triblock copolymer/homopolymer blend films, ABA/A and ABA/B,confined between two neutral hard walls were studied via Monte Carlo (MC) simulation on a simple cubic lattice. The effects of ψh (the volume fraction of homopolymer) and Mn/Mb (the molecular weight of homopolymer in relation to that of the corresponding blocks in the copolymer) on the morphologies were investigated in detail.     

MONTE CARLO SIMULATION OF TRIBLOCK COPOLYMER/HOMOPOLYMER BLEND FILMS

1. INTRODUCTION The extensive applications of block copolymer have been studied in detail due to their special molecular architecture and characteristic [1,2]. Recently, many studies including theoretical analysis and experimental techniques have addressed the polymer blend system of diblock copolymer/homopolymer [3~9]. An early investigation presented a quantitative analysis of homopolymer distributions in well-ordered copolymer microdomains through mixing polystyrene (PS) or poly methyl…     

PEO/PVAc共混体系辐射交联反应中溶胶分数与辐照剂量间的关系

交联度对由聚合物共混物辐射交联而制备出的材料的性能影响很大,研究共混体系的辐射交联度和交联行为是十分重要的。通常,用溶胶分数与辐照剂量间的关系表征聚合物的交联度和交联行为。文献[2]发现线性聚合物的溶胶分数与辐照剂量间的关系与高分子链结构参数有关。本文试图考察共混体系的辐射交联行为是否也与高分子链结构有关,并将线性聚合物的关系式(1)推广应用到PEO/PVAc共混体系中。目前,有关这方面的研究工作还未曾见文献详细报道。     

Synthesis,Characterization and Properties of Novel Amphiphilic Phosphated Ionomers by Ring‐Opening Reaction of Epoxidized Styrene‐Butadiene‐Styrene Triblock Polymer

A method for synthesis of novel phosphated ionomer of (styrene‐butadiene‐styrene) triblock polymer (SBS) from epoxidized SBS was developed. The optimum conditions for the ring‐opening reaction of the epoxidized SBS with aqueous solution of disodium hydrogen phosphate were studied. It was found that during the ring‐opening reaction phase transfer catalyst, ring‐opening catalyst and pH regulator were necessary to enhance the conversion of epoxy groups to ionic groups. The products were characterized with Fourier Transform Infrared Spectrophotometry (FTIR) and transmission electron microscopy (TEM). Some properties of the phosphated ionomer were studied. With increasing ionic groups or the ionic potential of the cation of the ionomer, the water absorbency emulsifying volume and the intrinsic viscosity of the ionomer increase, whereas the oil absorbency decreases. The ionomer possesses excellent emulsifying property, as compared with the sulfonated ionomer. The disodium phosphated ionomers in the presence of 10% zinc stearate showed better mechanical properties than the original epoxy SBS. Optimum mechanical properties occurred at the ionic group content of 0.95 mmol/g ionomer. When the ionomer was blended with crystalline polypropylene, a synergistic effect occurs with respect to the tensile strength. The ionomer behaves as a compatibilizer for blending equal amount of SBS and oil‐resistant chlorohydrin rubber (CHR) to form an oil resistant thermoplastic elastomer. SEM microphotographs indicated enhanced compatibility between the two components of the blend in the presence of the ionomer.     

聚（苯乙烯—丙烯酸）镨配合物中单体链段分布与配合物催化活性的关系

合成并表征了聚(苯乙烯(S)-丙烯酸(A))镨配合物(SAAC·Pr)。红外光谱表明它具有双配位结构:Pr?C—R。计算了共聚物中单体单元的序列分布。苯乙烯和丙烯酸单元长序列分布随其在共聚物中含量的增加而增加。当丙烯酸长序列分布高时,配合物的催化活性低。苯乙烯和丙烯酸的平均链长分别为ns=3,nA=1时,配合物的催化活性最高。     

含羧酸共生稀土光敏剂的低密度聚乙烯膜紫外光氧化降解

含羧酸共生稀土光敏剂的低密度聚乙烯膜紫外光氧化降解林宜超（福建省测试技术研究所福州３５０００３）近年来，许多作者先后研究并开发出含硬脂酸铈（ＣｅＳｔ３）光敏剂的可控光降解低密度聚乙烯（ＬＤＰＥ）［１，２］、高密度聚乙烯［３］、聚丙烯［４］、聚苯乙烯...     

Structure and properties for binary blends of isotactic-polypropylene with ethylene-α-olefin copolymer. 1. Crystallization and morphology

Morphology and isothermal growth rates of spherulites for the binary blends consisting of an isotactic polypropylene (i-PP) and an ethylene-1-hexene rubber (EHR) were examined as a function of the crystallization temperature ranging from 388 K to 418 K. In this study, two types of EHR's were employed: “ethylene rich” EHR and “1-hexene rich” EHR. The blends of i-PP with the EHR of 51 mol % 1-hexene are miscible in the molten state, whereas the blends with the EHR of 33 mol % 1-hexene are immiscible in the molten state. It is found that the isothermal spherulite growth rate of the miscible i-PP/EHR blends decreases with increasing the EHR fraction, whereas the spherulite growth rate of the immiscible i-PP/EHR blends is independent of the blend composition and is the same as that of the i-PP. Optical microscope observation of the miscible blends crystallized isothermally shows that there are no rubber domains either in the intraspherulitic or in the interspherulitic contact regions. On the other hand, the immiscible i-PP/EHR blends show a phase-separated morphology. Furthermore, the number of tangential lamellae of the miscible i-PP/EHR blends is found to be increased by blending of the EHR, leading to the spherulite with negative birefringence. The sign of birefringence of spherulites is unaffected by the regime transition as well as by the fold surface free energy. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35 : 953–961, 1997     

聚合物载体-稀土金属配合物的研究ⅩⅦ聚(苯乙烯-4-乙烯基吡啶)钕配合物在丁二烯聚合中的催化行为

聚合物载体－稀土金属配合物的研究．聚（苯乙烯－４－乙烯基吡啶）钕配合物在丁二烯聚合中的催化行为李晓莉于广谦＊李玉良（中国科学院长春应用化学研究所长春１３００２２）关键词苯乙烯，乙烯基吡啶，共聚物，钕配合物，丁二烯聚合１９９６－０４－１１收稿，１９９６...