像面照度均匀的环带式菲涅尔透镜设计

为了解决太阳光经传统菲涅尔聚光镜聚光后太阳能电池接收面上的光强分布不均匀问题,设计了一种环带式菲涅尔聚光镜。根据菲涅尔环带设计方法,把接收面划分为与之对应的环带,使光线在经过菲涅尔聚光镜的表面环带后进入相应的接受面环带,减少了光能损失并提高了光强分布均匀性。给出了在350 nm ~760 nm波段范围内太阳张角角度为0.54°、口径200 mm、高宽比为0.65、聚光比为400的菲涅尔聚光系统设计实例,通过Tracepro模拟并分析了菲涅尔聚光镜的光学能力。结果表明:在接收面尺寸相同的情况下与参数相同的的传统匀光菲涅尔聚光镜相比,此环带菲涅尔透镜光斑能量分布均匀性达到75%。     

分区域多焦点叠加方形光斑均匀聚光菲涅耳透镜设计

针对传统点聚焦菲涅耳透镜聚光分布均匀性较差以及聚焦光斑形状与太阳能电池片不匹配的缺点,提出了一种分区多焦点叠加方形光斑均匀聚光菲涅耳透镜的设计方法。在传统圆形同心环带点聚集菲涅耳透镜的基础上截取4个缺角等腰直角三角形菲涅耳透镜单元,做无缝拼接形成分区域四焦点叠加的方形光斑均匀聚光菲涅耳透镜,通过这4个区域光的叠加有效改善了聚光的均匀度。基于光线追迹法,采用TracePro光线模拟软件模拟并分析了环距、缺角弦长、腰长等透镜结构参数对聚焦光斑形状、聚光均匀度、辐照度等光学性能参数的影响。结果表明采用该方法设计的透镜聚焦光斑形状为方形,聚光均匀度高达90%以上。     

聚光镜型大口径菲涅耳透镜的设计理论和研制

为研制大口径聚光镜型菲涅耳透镜,本文建立了一套较完整的设计和分析理论。文中根据几何光学等光程完善成象的原理和象差理论,指出简化成聚光镜型菲涅耳透镜的原型透镜为非球面平凸透镜。本文在推导出两种类型的菲涅耳透镜的计算公式后,从棱镜对光束的影响、比较两种透镜的集光效率和球差值的大小诸方面,对菲涅耳透镜的类型进行了最优化选择。为了确定该透镜的焦距、环距、通光口经等参数,本文讨论了效     

高倍聚光模组系统研究与设计

聚光系统的聚光效率和能量均匀性直接影响单位模组的发电效率。本文研究设计出高倍聚光模组系统,该系统主要包括菲涅耳透镜和球冠平顶微棱镜。采用中心波长修正法进行菲涅耳透镜的设计,并通过Zemax仿真模拟设计出球冠平顶微棱镜。最后通过Zemax模拟,决定选取两侧面夹角α的角度为117°,平顶到球面的间隔g为0.2 mm,球冠平顶微棱镜的曲率半径R为10 mm。聚光系统整体的聚光效率达99.8%,能量均匀度为0.812,并进行实验验证,得出实际聚光效率为83.1%。     

新型线聚焦菲涅耳透镜设计及其聚光特性研究

聚光光伏系统中电池表面热流密度分布不均匀导致系统光电转换效率降低,同时出现局部过热问题,严重影响了光伏电池系统的效率。为了解决这一问题,本文设计了一种可以使太阳投射辐射能量均匀化分布于接收面的新型线聚焦菲涅耳透镜,并运用蒙特卡罗光线追迹法对常见的菲涅耳透镜及本文设计新型线聚焦菲涅耳透镜的聚光特性进行了对比研究。模拟结果表明,新型透镜极大地改善了电池表面热流分布的均匀性。针对新型透镜聚光特性,考察了不同设计接受面宽度、太阳光不平行灾角、入射光束波长、入射光倾角及电池位置等因素对电池表面热流密度分布的影响。     

等厚型平板菲涅尔透镜设计与研究

针对当前曲面菲涅尔透镜普遍存在的加工工艺复杂、面型精度难于控制、制作成本较高等问题,在研究非等厚型平板菲涅尔透镜设计方法的基础上,提出一种中心透镜为球面、外侧环带为倾斜面的等厚型平板菲涅尔透镜的设计方法,给出了具体的设计实例,并进行了建模和光学仿真,模拟结果表明:该菲涅尔透镜设计的光学效率达到90.7%。     

大型菲涅耳透镜的设计和制造

介绍一种大口径六环组合光学玻璃大型菲涅耳透镜的光学设计原理、整体工艺方案、各个球面环带的工艺计算和加工方法 ;讨论了大型菲涅耳透镜的光学胶合以及整体扇型切割成型方法 ;给出了研制成功大型菲涅耳透镜的光学检测结果。     

基于紫外纳米压印的菲涅耳透镜制作

针对传统聚光系统中菲涅耳透镜成本较高并且光强分布不均匀的弊端,提出了利用紫外纳米压印技术制作菲涅耳透镜的方法.利用几何光学的光线追迹理论,设计了菲涅耳透镜模具.采用自行研制的紫外纳米压印系统对模具进行压印,紫外曝光后制得薄膜菲涅耳透镜.在太阳光下进行了测试,测试结果表明,低成本、高聚光倍数和光强分布均匀的菲涅耳透镜是可以实现的.     

基于紫外纳米压印的菲涅耳透镜制作

针对传统聚光系统中菲涅耳透镜成本较高并且光强分布不均匀的弊端,提出了利用紫外纳米压印技术制作菲涅耳透镜的方法.利用几何光学的光线追迹理论,设计了菲涅耳透镜模具.采用自行研制的紫外纳米压印系统对模具进行压印,紫外曝光后制得薄膜菲涅耳透镜.在太阳光下进行了测试,测试结果表明,低成本、高聚光倍数和光强分布均匀的菲涅耳透镜是可以实现的.     

聚光模组二次光学元件优化设计与研究EI北大核心CSCD

聚光光伏模组中,二次光学元件对增加太阳能电池接收到的入射光能量,提高聚焦光斑均匀性和增大菲涅耳透镜接收角具有重要作用。设计了一种用于聚光光伏模组的全反射式二次光学元件,用Solidworks软件建立了三维模型,结合实际工程应用,借助Zemax软件光学模拟仿真手段,对二次光学元件的倾角和高度等重要参数进行了优化。并制作了不同参数的二次光学元件,配合菲涅耳透镜、太阳能电池,搭建了实物聚光发电单元,在太阳模拟器下进行I-V性能测试,结果表明当二次光学元件高度为6 mm,上圆直径为7 mm时,太阳能电池的输出功率达到最大值720 m W,与不加二次光学元件相比,输出功率提高了16%。说明该二次光学元件对提高聚光模组效率作用显著。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.