Improvement in superconductivity of TlBa2CaCu2Oy system by introduction of oxygen loss

The T_c and oxygen content of TlBa₂CaCu₂O_y have been investigated by quenching experiments, in which the heat-treated samples were dropped into liquid nitrogen. The oxygen loss, v, of TlBa₂CaCu₂O_{yo − v} was determined by thermogravimetry in a nitrogen atmosphere using an oxygen-annealed specimen of TlBa₂CaCu₂O_yo and also by measurements of the weight differences before and after quenching. T_c increased from 80 K of the oxygen-annealed specimen up to about 110 K with increasing oxygen loss up to v = 0.035 by annealing at 500°C in a nitrogen atmosphere. Judging from the high T_c above 110 K achieved by a small oxygen loss about v = 0.035, the as-sintered oxygen-annealed TlBa₂CaCu₂O_yo specimen was in the over-doping state and probably has an oxygen vacancy of 7 − y_o0.     

Effect of lead addition to Bi-based 2222 superconducting cuprates Bi2-xPbxSr2(Y, Ce)2Cu2O10+δ

Bi_2-xPb_xSr₂(Y, Ce)₂Cu₂O_10+δ, a new family of lead containing Bi-2222 compounds has been synthesized and effects of annealing in high pressure of oxygen studied. Lead-free Bi₂Sr₂(Y, Ce)₂Cu₂O_10+δ synthesized under flowing oxygen is known to be non-superconducting, but annealing under high oxygen pressure (100 bar) at 500°C, induced superconductivity with T_c=25 K. On substitution of lead (x>0.4), the superconductivity appears even in samples synthesized under flowing oxygen (1 bar). T_c increases with oxygen annealing pressure for all compositions, and it also increases with Pb content at a given oxygen pressure. These findings are discussed.     

SiO2 passivation film effects on microwave characteristics of YBa2Cu3O7−x-based resonators

SiO₂ film coated as a passivation layer for YBa₂Cu₃O_7−x (YBCO)-based microwave devices is investigated by measuring the microwave characteristics of microstrip line resonators. The SiO₂ film is deposited with its 0.3 to 0.4 μm thickness by a sputtering method using Ar + 30%O₂ plasma. These deposition conditions do not degrade the microwave characteristics and the critical temperature (T_c). Next, the SiO₂ film coated resonators are compared with the uncoated ones for two kinds of degradation conditions: a 200°C annealing in air, and an exposure to air at 85°C and 85% RH (relative humidity). We find that the SiO₂ passivation film prevents the YBCO thin film from the surface degradation and reacting with water.     

Electrical and structural properties of epitaxially grown Y1Ba2Cu3O7 − x and Y2Ba4Cu8O16 − x thin films using the BaF2 method

Thin films of Cu, Y and BaF₂ are co-condensed in ultrahigh vacuum onto SrTiO₃ (1 0 0)-substrates at room temperature without any additional oxygen supply. It is found that the temperature of the ex situ fluorine-oxygen exchange reaction in flowing wet oxygen essentially determines whether the Y₁Ba₂Cu₃O_{7 − x}-phase (T_ex = 850°C) or the Y₂Ba₄Cu₈O_{16 − x}-phase (T_ex = 800°C) forms or any mixture of both phases in between. Small-angle X-ray diffraction verifies the strictly epitaxial growth of the superconducting phases. The variation of the composition around the ideal 1,2,3-stoichiometry affects only the superconducting and normal conducting properties which are measured using the four-probe Montgomery method. The values of the normal state resistivity and its temperature dependence are discussed in combination with a reduced cross section of the conduction paths in the films.     

Synthesis and properties of Hg0.7Pb0.3(BaSr)2Ca2Cu3Oz superconductors

We have synthesized Hg(Pb)-1223 with substitutions of Sr for Ba, i.e. Hg_0.7Pb_0.3Ba_2−xSr_xCa₂Cu₃O_z (x = 0.0–2.0) by the ampoule method. The spray-drying method and thermal decomposition under vacuum were applied for the preparation of homogeneous precursors. Samples with T_c = 110–128 K were obtained without oxygen annealing. We found that substitution of Ba by Sr remarkably relaxed the requirements on the precursors preparation and allowed their handling under ambient conditions.     

NMR study of local hole distribution, spin fluctuation and superconductivity in Tl2Ba2Ca2Cu3O10

⁶³Cu, ¹⁷O and ²⁰⁵Tl NMR have been performed in the high-T_c superconductor Tl₂Ba₂Ca₂Cu₃O₁₀ whose T_c(max) is 127 K. The hole densities at Cu and oxygen sites in the CuO₂ plane have been extracted from the nuclear quadrupole frequency ν_Q. The striking feature is that the Cu holes are significantly transferred to oxygen site due to strong hybridization between Cu and oxygen. From an analysis of T₁ and T_2G, it has been found that the spectral weight of the spin fluctuation is transferred to higher energy compared to YBa₂Cu₃O₇, while the magnetic correlation length ξ does not differ much. Thus, it is suggested that the higher T_c is due to higher characteristic energy of spin fluctuations, i.e. the superconductivity is spin fluctuation mediated. The superconducting properties are consistently explained by a d-wave superconductivity model with a finite density of states (DOS) at the Fermi level. We show that the disorder of the Ca/TlO layer caused by the partial inter-substitution of Tl and Ca is responsible for the potential scattering to produce such a DOS. It is found that if such a potential scattering were absent, T_c would go up to 132 K which is quite close to the record T_c realized in the Hg based compound.     

Temperature dependence of induced magnetic anisotropy in metallic glasses (Fe1 − xCox)78Si10B12

The variations of induced magnetic anisotropy with annealing and measuring temperatures in metallic glasses (Fe_{1 − x}Co_x)₇₈Si₁₀B₁₂ have been measured. It was found that K_u (T) was proportional to Mⁿ_s (T) for T below 200°C, and the index n varied with the cobalt content x and annealing conditions, not being smaller than 3. To the predictions of the existing pair-ordering and single-ion theories, the above results are anomalous. By considering the distributions of exchange integrals and activation energies in metallic glasses, this anomalous behaviour could be explained properly.     

Giant pressure effect in oxygen deficient YBa2Cu3Ox

The pressure effect on T_c of polycrystalline and single crystalline YBa₂Cu₃O_x investigated as a function of oxygen content x by ac-susceptibility measurements under helium pressure. In the overdoped region x> 6.93 the single crystals show a negative dT_c/d p, as expected from the charge transfer model. For optimally doped samples with x = 6.93 we find dT_c/d P = 0.4 K/GPa which points to pressure effects on T_c aside from charge transfer. In the underdoped region x < 6.93 the dT_c/d p values obtained from the experiment depend strongly on the storage temperature of the sample during the experiment. When the samples are stored at temperatures well below 240 K throughout the entire experiment including pressure application and pressure release, dT_c/d p increases to approx. 7 K/GPa at x = 6.7 but with a further decrease of the oxygen content the dT_c/d p drops to approx. 2 K/GPa at x = 6.4. These effects are intrinsic to the YBa₂Cu₃O_x structure and can be explained by considering the anisotropic structure of YBa₂Cu₃O_x. The decrease of the c-axis lattice parameter results in a charge transfer to the CuO₂-planes mainly [1], whereas the compression of the a- and b-axis lattice parameter is known to produce different pressure effects which are responsible for the peak in dT_c/d p at x = 6.7 [2]. When pressure is changed at room temperature oxygen ordering effects occur which cause a relaxation of T_c to the equilibrium value T_c(p) at this pressure with a time constant depending on the oxygen content x. A decrease x results in a peak effect in dT_c/d p at x = 6.7 again, which is enhanced to approx. 12 K/GPa. If the oxygen content is decreased further, dT_c/d p first drops to 5 K/GPa at x = 6.6, but the increases to values of more than 20 K/GPa for x < 6.42. These giant pressure effects at low oxygen contents are mainly caused by a reversible T_c increase (dT_c/d p)_O due to pressure induced oxygen ordering via oxygen motion between unit cells.     

Phase diagrams of YBa2Cu4O8 and YBa2Cu3.5O7.5 in the pressure range 1 bar≤PO2≤3000 bar

The P-T-x phase diagram of the pseudobinary system (Y-Ba-Cu-O)-O₂ has been further investigated in the oxygen pressure range between 1 and 3000 bar. The stability ranges of the phases YBa₂Cu₄O₈ (124), YBa₂Cu_3.5O_7.5−x (123.5) and YBa₂Cu₃O_7−x (123) have been determined. Long duration experiments showed that the 123 phase is not stable at least down to 7 bar≤P≤20 bar oxygen and 900°C. It is not clear whether at lower pressures and temperatures the 123 phase is thermodynamically stable or metastable due to low reaction rates. In the presence of excess CuO, the 124 is the stable phase. The melting of 124 pellets at P_O2=2800 bar shows that even at this pressure the 124 compound melts incongruently. Using the phase diagram data we could change the T_c of 123.5 from 16 to 70 K by varying systematically the nonstoichiometry. Due to a narrow homogeneity range the T_c of 124 remained constant but is different for powder pellets (81 K) and for crystals (70 K), probably due to the influence of the flux. Single crystals of both 124 and 123.5 with dimensions up to 4 mm were grown from the flux under high oxygen pressure.     

The effects of substrate temperature on the superconducting properties of Tl2Ca2Ba2Cu3O10 films sputter-deposited from stoichiometric oxide targets

The annealing characteristics and the superconducting properties of Tl₂Ca₂Ba₂Cu₃O₁₀ thin films sputter-deposited onto yttrium- stabilized ZrO₂ substrate at up to 500°C from two stoichiometric oxide targets are reported. The films deposited at 400–500°C were found to require a lower post-annealing temperature than the films deposited at lower temperatures to attain the highest T_c superconducting state, due to a more pronounced Ba diffusion toward the substrate as indicated by their secondary ion mass spectrometry depth profiles. The highest T_c achieved tends to degrade with increasing substrate temperatures, a zero resistance T_c of 121 and ≈90 K, respectively, being observed for the films deposited at -ambient temperature and at 500°C. The formation of the highest T_c phase (Tl₂Ca₂Ba₂Cu₃O₁₀) generally is associated with a sheet type of crystal growth morphology with smooth and aligned surfaces which can be obtained only from the films capable of sustaining prolonged annealing at 900°C. Annealing at lower temperatures (≈860°C) results in the formation of rod or sphere type of morphologies with rough and randomly oriented crystals and the lower T_c phases such as Tl₂Ca₁Ba₂Cu₂O₈.     

Electronic structure of (Nd, Ce)2(Ba, Nd)2Cu3Oy

The dependence of T_c on oxygen content was determined for (Nd_0.67Ce_0.33)₂(Ba_0.67Nd_0.33)₂Cu_3.01O_y. It was found that superconduction appears in a range of y=9.10−9.16 and that T_c is enhanced remarkably by the increase of oxygen content. In an oxygen content range where superconduction appeared, the Ce valence was nearly +4 and the Cu valence changed from 2.31 to 2.33. The conductivity was measured in a wide temperature range between T_c and 1200 K as a function of oxygen partial pressure. The high-temperature conductivity increased with increasing oxygen content. It was found that both carrier concentration and mobility are increased with oxygen content. The conduction at low temperatures was semiconductor-like, and increased with increasing oxygen content, where the energy gap E_A-E_V between acceptor level and top of filled band approached zero.     

The effect of gallium substitution on the superconductivity of the BiSrCaCuO system

Magnetic susceptibility, X-ray diffraction and resistivity measurements of the system Bi_1.4Pb_0.6Sr₂Ca_2−xGa_xCu₃O_y are reported for 0 x 2. The high-T_c 2223 phase with a T_c of 107 K for x = 0 exists for x 0.3. The low-T_c 2212 phase with a T_c of 75 K for x = 0 exists for the full range of x. The highest values of the critical temperature and the largest volume fraction of the low-T_c phase in compounds with Ga occur for x = 0.5 ± 0.1. The identification of CaO by X-ray diffraction for x 0.6 indicates that Ga replaces Ca in the compound.     

Oxygen nonstoichiometry and phase transitions of the neodymium-rich Nd1+xBa2−xCu3Oz solid solution

On the basis of chemical, thermal analysis and Cu K-edge X-ray absorption measurements, oxygen content in the Nd_1+xBa_2−xCu₃O_z solid solution was determined between 1000°C in air and 400°C in oxygen for x=0.05–0.9 compositions. It has been observed that the oxygen nonstoichiometry Δz of the Nd_1+xBa_2−xCu₃O_7+x/2−Δz solid solution decreases 2–2.5 times for a large substitution (Δz≈0.3–0.33 for x=0.9), despite of the acclaimed higher total oxygen content. The difference in nonstoichiometry is explained by a higher average value of the copper oxidation state (ACV), which is vital for the solid solution with large x even at elevated temperatures (ACV≈2–2.05 for x>0.3 at 1000°C, PO₂=0.21 atm). On the contrary, the ACV after complete oxygenation is almost constant (about 2.25–2.3) for the whole series. The x-dependence of the oxygen content is not monotonous and structural phase transitions can be observed at x=0.3 and x=0.6, as confirmed by the X-ray diffraction and the Raman scattering spectroscopy. The first well-known transition is connected with the oxygen disorder due to the Nd substitution for Ba at random Ba-sites. In the present work, it is proved by the apical oxygen mode broadening in Raman spectra. Ordering of the Nd and Ba atoms with a subsequent orthorhombic distortion of the lattice may occur even at 1000°C in air due to the second transformation at x≈0.6. The invariable orthorhombicity of the Nd-rich solid solution with x>0.6 is not caused by the oxygen absorption as in the x=0.05 case. Existence of high- and low-temperature orthorhombic modifications of this solid solution has been observed for the first time. Finally, a tentative 3D (z–x–T) diagram is suggested for the Nd_1+xBa_2−xCu₃O_z solid solution up to 1000°C in air, including the new x=0.6–0.9 region.     

Synthesis of YBa2Cu3O7−x superconducting thin films on LaAlO3 by means of PAMOCVD

High-T_c superconducting thin films have been deposited in situ by means of a plasma assisted metal-organic chemical vapour deposition (PAMOCVD) process on LaAlO₃. An EMCORE high-speed rotating disc reactor was used to deposit the films at a substrate temperature of 600°C to 800°C. The system is equipped with a (remote) 120 W microwave plasma generator. The oxidising plasma gas is N₂O and/or O₂ while Ar was used as the inert carrier gas for the different metal-organics. The influence of different process parameters (such as the temperatures of the metal-organics, substrate temperature, and plasma gas composition) on the superconductive properties and on the morphology of the films was investigated. Surface morphology and composition were studied by SEM/EDX or EPMA, and AC susceptibility measurements were used to investigate the superconductive properties (T_c and J_c). X-ray diffraction measurements indicated that single-phase YBa₂Cu₃O_7−x films were epitaxially grown with the 00l orientation perpendicular to the substrate surface. The critical temperature (T_c) of the films is about 90 K and the critical current density (J_c) is higher than 10⁶ A/cm² at 77 K and zero field.     

Ramans study of Y1−xPrxBa2Cu3O7−δ and YB2Cu3−xZnxO7−δ single crystals

Single crystals with known T_c values of Y_1−xPr_xBa₂Cu₃O_7−δ (Y---Pr1:2:3) and YBa₂Cu_3−xZn_3−xZn_xO_7−δ (Y---Zn1:2:3) systems are studied by Raman measurements. The Raman spectra for (Y---Pr1:2:3) single crystals show that the frequencies of Ba and O_z modes increase as the Pr content increases. The results are consistent with the hole-localization scheme proposed for the suppression of superconductivity in the polycrystalline Y---Pr1:2:3 systems. On the other hand, in the Y---Zn1:2:3 system, all the Raman modes do not change in frequencies. However, the FWHM of the Cu(2) mode increases with the decrease of T_c, indicating strong scattering of charge carriers by the substituted Zn ions in the CuO₂ planes. The induced disorder in the CuO₂ planes may be related with suppression of T_c in the Y---Zn1:2:3 system. Thus, the suppression mechanism in the Y---Zn1:2:3 systems seems to be different from that in the Y---Pr1:2:3 systems.     

Resistivity and thermoelectric power of Bi2Sr2Ca−xPrxCu2Oy system

Samples of Bi₂Sr₂Ca_1−xPr_xCu₂O_y have been characterized by resistivity and thermoelectric power measurements. All metallic samples show superconductivity with a maximum T_c = 90 K at X = 0.2. The sample of x = 0.6 shows a crossover from hopping conduction at low temperature above T_c to metallic conduction at high temperature. For the metallic samples below x = 0.6, the results of thermoelectric power are well fitted by both of a phenomenological band spectrum model and the Nagaosa and Lee model.     

Carbon solubility and superconductivity in MgB2

Successful replacement of B by C in the series MgB_2−xC_x for values of x upto 0.3 is reported. Resistivity and ac susceptibility measurements have been carried out in the samples. Solubility of carbon, inferred from the observed change in the lattice parameter with carbon content indicates that carbon substitutes upto x=0.30 into the MgB₂ lattice. The superconducting transition temperature, T_c measured both by zero resistivity and the onset of the diamagnetic signal shows a systematic decrease with increase in carbon content upto x=0.30, beyond which the volume fraction decreases drastically. The temperature dependence of resistivity in the normal state fits to the Bloch–Gruneisen formula for all the carbon compositions studied. The Debye temperature, θ_D, extracted from the fit, is seen to decrease with carbon content from 900 to 525 K, whereas the electron–phonon interaction parameter, λ, obtained from the McMillan equation using the measured T_c and θ_D, is seen to increase monotonically from 0.8 in MgB₂ to 0.9 in the x=0.50 sample. The ratio of the resistivities between 300 and 40 K versus T_c is seen to follow the Testardi correlation for the C substituted samples. The decrease in T_c is argued to mainly arise due to large decrease in θ_D with C concentration and a decrease in the hole density of states at N(E_F).     

Effect of Cu doping in MgB2 superconductor at various processing temperatures

The effects of Cu doping in MgB₂ superconductor has been studied at different processing temperatures. The polycrystalline samples of Mg_1−xCu_xB₂ with x = 0.05 were synthesized through the in-situ solid sate reaction method in argon atmosphere at different temperature range between 800–900 °C. The samples were characterized through X-ray diffraction (XRD), Scanning Electron Microscopy (SEM) and low temperature R–T measurement techniques for the phase verification, microstructure and superconducting transition temperature, respectively. The XRD patterns of Mg_1−xCu_xB₂ (x = 0.05) do not exhibit any impurity traces of MgB₄ or MgB₆ and they show the sharp transition in the samples prepared at 850 °C. The onset transition temperature of the prepared samples is around 39 K, which is almost the same as that for the pure MgB₂. This indicates that Cu doping in MgB₂ does not affect the transition temperature. The SEM micrograph of Mg_0.95Cu_0.05B₂ has shown that the sample is dense with grain size smaller than 1 μm.     

Magnetic moments and Fe hyperfine field interactions in Y(Fe1−xRux)2 ternaries

Measurements of magnetization and ⁵⁷Fe Mössbauer spectra have been made for Y(Fe_1−xRu_x)₂. The C15 type cubic structure is stabilized for xx 0.7. The C15 compounds is ferromagnetic with T_c200 K and its saturation moment decreases monotonically with increasing x, while the ⁵⁷Fe hyperfine field decreases only slightly with x. From these results, it is deduced that the Ru atoms have an induced moment of ≈1μ_B in the range x 0.2. In the C14 type phase, no magnetic ordering develops even at 4.2 K.     

Crystal structure, superconductivity and magnetic properties of the superconducting ferromagnets Gd1.4−xDyxCe0.6Sr2RuCu2O10 (x=0–0.6)

The structural, electrical and magnetic properties of the superconducting ferromagnets, Gd_1.4−xDy_xCe_0.6Sr₂RuCu₂O₁₀ (x=0–0.6) are systematically investigated as a function of Dy doping and temperature. These compounds are characterized by high temperature superconductivity (T_c ranging from 20 to 40 K depending upon the Dy content) co-existing with weak ferromagnetism with two magnetic transitions (T_M2 ranging from 95 to 106 K and T_M1 around 120 K). Doping with Dy gives no significant structural changes except for a minor change in the c/a ratio. However the superconducting transition temperature is significantly suppressed and magnetic ordering temperature enhanced on Dy doping. These effects are described and discussed.