Swelling behavior of poly- N-isopropylacrylamide microgel particles in alcoholic solutions

 It has been shown that the swelling of poly-N-isopropyl-acrylamide (poly-NIPAM) microgel particles can be controlled by the addition of alcohols, in addition to the previously observed effect of temperature. The degree of swelling is also controlled by the amount of cross-linker within the microgel particles. At 25 ^°C, poly-NIPAM microgel particles collapse upon the addition of MeOH, EtOH and 2-PrOH to a minimum size and then, reswell again as the alcohol-rich region is approached. This trend was also observed for poly-NIPAM microgel particles dispersed in 2-PrOH/water mixtures upon heating to 50 ^°C. The particles, dispersed in either water or alcohol/water mixtures were found to be stable to flocculation between 25 ^°C and 50 ^°C. Received: 27 February 1997 Accepted: 5 August 1997     

Physicochemical characterization of a novel surfactant peptide containing an arginine cation and laurate anion

 A novel surfactant peptide consisting of an arginine cation with laurate anion has been synthesized, purified and characterized. The critical micellar concentration (cmc) of peptide in aqueous solutions has been determined using spectroscopic techniques and is found to increase from 0.06 to 0.11 mM with increasing temperature (15–45 °C). Cmc is also determined in the presence of salts like NaCl, KCl and sodium acetate and it is found that these electrolytes hinder aggregation with a significant increase in the case of sodium acetate. The aggregation number of the surfactant peptide has been determined using fluorescence quenching measurements and is observed to decrease from 14 to 6 with increasing temperature (15–45 °C). The standard free energy change (ΔG ⁰ _m) and standard enthalpy change (ΔH ⁰ _m) of the peptide aggregate are found to be negative with a small positive value for standard entropy change (ΔS ⁰ _m). The peptide aggregate seems to undergo phase transition above 50 °C as observed from UV–vis and fluorescence spectroscopy. From pyrene binding studies, it is shown that the interior dielectric constant increases from 5.08 at 34 °C to 8.77 at 50 °C and further decreases with increase in temperature indicating a phase change at 50 °C. Also, the ratio of excimer intensity to monomer intensity, which is a measure of microviscosity of the aggregate, decreases with increase in temperature with a change at 50 °C indicating a phase change. Received: 14 February 1997 Accepted: 13 August 1997     

Coil-to-globule-type transition of poly(N-isopropylacrylamide) adsorbed on colloidal silica particles

 The temperature dependence of the dimensions of poly(N-isopropylacrylamide) (PNIPAM) adsorbed on two different colloidal silica particles was studied with dynamic light scattering. The hydrodynamic diameter was measured when the temperature was varied stepwise from 10 to 60 °C. PNIPAM molecules free in solution undergo a conformational transition at the θ temperature. We have found that PNIPAM adsorbed onto silica particles also undergoes a transition below the θ temperature. When a small amount of polymer was adsorbed the coil-to-globule transition at the θ temperature did not occur. Potentiometric titrations showed that the surface charge of the silica particles was not affected by the polymer adsorption. Sodium dodecyl sulfate (SDS) (100–1200 mg/l) was added to improve the stability. The particles with a higher zeta potential required a smaller addition of SDS to prevent coagulation compared to the particles with a smaller surface potential. For low additions of SDS the transition curves of adsorbed PNIPAM were unaffected. For larger additions of SDS the collapse of PNIPAM was shifted to higher temperatures. When as much as 1200 mg/l SDS was added, two regions with weak transitions were observed before the collapse. It was also observed that the presence of SDS results in a smaller adsorption of PNIPAM onto the particles. The addition of SDS strongly increased the magnitude of the electrophoretic mobility of the polymer–particle unit. From the electrophoretic measurements an electrokinetic layer thickness was calculated and it was found to be smaller than the corresponding hydrodynamic layer thickness, as obtained by dynamic light scattering. Received: 14 December 1999/In revised form: 22 February 2000/Accepted: 6 March 2000     

Production of electrically conductive, core/shell polystyrene/polyaniline composite particles by chemical oxidative seeded dispersion polymerization

Micron-sized, monodispersed, electrically conductive polystyrene (PS)/polyaniline (PAn) composite particles were produced by chemical oxidative seeded dispersion polymerization of aniline at 0 °C with 1.37-μm-sized, monodispersed PS seed particles in HCl aqueous solution, where the pH value was kept at 2.5 with a pH stat. The composite particles consisted of a PS core and a PAn shell. A pellet of the composite particles had a conductivity of 3.4 × 10⁻³ S/cm. Received: 5 April 2000 Accepted: 10 August 2000     

Cationic amino-containing N-isopropyl- acrylamide-styrene copolymer particles: 2-surface and colloidal characteristics

 In a previous paper [1], the synthesis of various polystyrene– poly[NIPAM] core–shell latexes bearing cationic amidino and/or amino charges has been described. Several colloidal properties of these cationic latexes have been charac-terized such as: particle size, surface charge density, electrophoretic mobility and finally colloidal stability. Due to the poly[NIPAM]-rich layer in the shell, it was found that temperature played a significant role on all these properties, a LCST around 33 °C being exhibited. In addition, ionic strength was also found to affect the colloidal behavior of these latexes, the largest effect being observed with latexes having both amidino and amino surface charges. The critical coagulation concentra-tions (CCC) of the various latexes above and below the LCST were determined, highlighting the contribution of electrostatic and steric repulsive forces to the stability of these particles. Received: 20 January 1998 Accepted: 8 June 1998     

Production of submicron-sized poly(methyl methacrylate) particles by dispersion polymerization with a poly(dimethylsiloxane)-based azoinitiator in supercritical carbon dioxide

 Submicron-sized, comparatively monodisperse poly (methyl methacrylate) particles were produced by dispersion polymerization of methyl methacrylate with a poly(dimethylsiloxane)-based azoinitiator in supercritical carbon dioxide at 30 MPa for 24 h at 65 °C. The initiator operated not only as a radical initiator but also as a colloidal stabilizer, and was named an “inistab”. Received: 13 February 2001 Accepted: 20 June 2001     

Studies of mechanism of silica polymerization reactions in the combination of silica sol and potassium sodium waterglass via isothermal heat conduction microcalorimetry

Isothermal heat conduction microcalorimetry was adopted as a novel characterization method to investigate the polymerization processes of silica when the combination of silica sol and potassium sodium silicate was stirred at 25.0, 35.0, and 45.0 °C. Thermodynamic and kinetic parameters were simultaneously obtained. The enthalpy change was greater at each higher temperature. The reaction orders (m, n) instantaneously varied, up and down in an alternate manner. At 25.0, 35.0, and 45.0 °C, the rate constants were different; the maximum rate constant occurred at 25.0 °C. These phenomena reflect a two-stage oligomeric mechanism of silica monomers. The measurements of particle size showed the complex chemical composition of aqueous silicates, which can be qualitatively designated by the particle size distribution in two parts. The results further indicate that the colloidal particles in the mixed silica sol and silicates first dissolved. Then the “active” silica in the silicates redeposited to make a distinct particle size distribution influenced by K⁺ and Na⁺ ions as well as by temperature.     

Morphology of micron-sized monodispersed composite polymer particles produced by seeded polymerization for the dispersion of highly monomer-swollen polymer particles

 Monodispersed polystyrene (PS)/poly(n-butyl methacrylate) (PBMA) composite particles having 9.4 μm in diameter were produced by seeded polymerization for the dispersion of highly n-butyl methacrylate (BMA)-swollen PS particles, and their morphologies were examined. The highly BMA-swollen PS particles (about 150 times the weight of the PS seed particles) were prepared by mixing monodispersed 1.8 μm-sized PS seed particles and 0.7 μm sized BMA droplets prepared with an ultrasonic homogenizer in ethanol/water (1/2, w/w) medium at room temperature. After NaNO₂ aqueous solution as inhibitor was added in the dispersion, the seeded polymerization was carried out at 70 °C. In an optical microscopic observation, one or two spherical high contrast regions which consisted mainly of PS were observed inside PS/PBMA composite particles. In the PS domain, there were many fine spherical PBMA domains. Such morphologies were based on the phase separation of PS and PBMA within the homogeneous swollen particles during the seeded polymerization. Received: 04 June 1997 Accepted: 27 August 1997     

Polymer modification of colloidal particles by spontaneous polymerization of surface active monomers

Adsorption and spontaneous polymerization of head- or tail-type surface active monomers having long methylene chains on colloidal silica and δ-alumina were investigated. Both head-type and tail-type ammonium monomers on silica in chloroform or tetrahydrofuran had the maximum adsorption on the respective adsorption isotherm. Above the monomer concentration giving the maximum adsorption, it was observed that the monomer formed micelles or clusters in bulk solution with removal of adsorbed water molecules from the silica surface. At the monomer concentration giving the maximum adsorption, heating the silica suspension containing the monomer at 40°C or 60°C in tetrahydrofuran or chloroform solution resulted in spontaneous polymerization. The composite particles formed by polymerization were observed to have many spots consisting of polymer on the surface. Therefore, it is suggested that the monomers are concentrated by micelle-like aggregation on the silica surface and consecutively spontaneous polymerization takes place. Adsorption of an anion-type monomer having a carboxyl group on δ-alumina, which exhibited a positive ζ potential in neutral aqueous solution, was higher than that on colloidal silica, but did not spontaneously polymerize on alumina. Received: 13 June 1998 Accepted in revised form: 19 August 1998     

Observation of nanoparticles and film formation by scanning tunneling microscopy: methyl methacrylate/butyl methacrylate nanoparticles prepared by microemulsion polymerization

 Latexes as dispersions of poly(methyl methacrylate-co-butyl methacrylate) copolymeric nanoparticles within water were produced by microemulsion polymerization of the respective comonomers. Polymer yield, number-average and weight-average molecular weights, polydispersity index, and the glass-transition temperature of the copolymer produced were 50%, 8.8 × 10⁴, 2.54 × 10⁵, 2.87, and 45 °C. Scanning tunneling microscopy (STM) images of the latex nanoparticles and film formation on highly oriented pyrolitic graphite (HOPG) were obtained with a 2 V sample bias and a tunneling current of 20 pA. The STM pictures revealed that the particle size was 18 ± 3 nm. There was no film formation in the case of dehydration at room temperature. There was some coalesence of particles when the HOPG surface was preheated at 55 °C, while complete film formation was achieved when the latexes were annealed at 55 °C in an oven for about 10 min. Received: 23 August 1999 Accepted: 17 January 2000     

Production of soft core/hard shell composite polymer particles by the stepwise heterocoagulation method with heat treatment

Soft core/hard shell composite polymer particle was prepared by the stepwise heterocoagulation, which was proposed by authors in 1990, of many cationic hard small polymer particles (SPs) onto an anionic soft large polymer particle (LP). The powder was obtained by freeze-drying at 0 ^°C which was higher than glass transition temperature of LP (−7 ^°C) and lower than that of SP (90 ^°C). Received: 9 December 1997 Accepted: 12 May 1998     

Morphology of micron-sized monodispersed poly(butyl methacrylate)/polystyrene composite particles produced by seeded dispersion polymerization

In order to develop the seeded dispersion polymerization technique for the production of micron-sized monodispersed core/shell composite polymer particles the effect of polymerization temperature on the core/shell morphology was examined. Micron-sized monodispersed composite particles were produced by seeded dispersion polymerizations of styrene with about 1.4-μm-sized monodispersed poly(n-butyl methacrylate) (Pn-BMA) and poly(i-butyl methacrylate) (Pi-BMA) particles in a methanol/water (4/1, w/w) medium in the temperature range from 20 to 90 °C. The composite particles, PBMA/polystyrene (PS) (2/1, w/w), consisting of a PBMA core and a PS shell were produced with 2,2′-azobis(4-methoxy-2,4-dimethyl valeronitrile) initiator at 30 °C for Pn-BMA seed and with 2,2′-azobis(isobutyronitrile) initiator at 60 °C for Pi-BMA seed. The polymerization temperatures were a little above the glass-transition temperatures (T _g) of both Pn-BMA (20 °C) and Pi-BMA (40 °C). On the other hand, when the seeded dispersion polymerizations were carried out at much higher temperatures than the T _g of the seed polymers, composite particles having a polymeric oil-in-oil structure were produced. Received: 14 October 1998 Accepted in revised form: 2 June 1999     

Controlling apatite microparticles formation by calcining electrospun sol–gel derived ultrafine silica fibers

Electrospun ultrafine silica fibers were calcined at 150–800 °C. The relation of calcination temperature to the ability to form biomimetic apatite in a simulated body fluid solution (SBF) was evaluated. The largest apatite particles, formed on non-calcined fibers after 1 week of soaking in SBF, were 10 μm in diameter, had a narrow size distribution (coefficient of variation 9%), and were similar to pearls on string. The particles size decreased with increasing calcination temperature below 250 °C and the particles formed on the fibers calcined at 250 °C were 4.5 μm in diameter. No particles were found on those calcined above 500 °C. By using a concentrated SBF at 1.5-times higher ionic concentrations than SBF, the size of apatite microparticles increased about 50%. The fibrous substrate covered with apatite particles was effective for osteoblastic differentiation of pre-osteoblastic cells.     

Poly(styrene-b-ethylene oxide) copolymers as stabilizers for the synthesis of silica–polystyrene core–shell particles

Following previous works [1, 2], silica–polystyrene core–shell particles have been synthesized by dispersion polymerization of styrene in an ethanol/water mixture in the presence of a poly(styrene-b-ethylene oxide) block copolymer as stabilizer. Besides the formation of composite core–shell particles, a large number of free latex particles that do not contain silica were also formed. This number decreases as the size of the silica beads decreases from 300 to 29 nm in diameter, and becomes very low compared to the number of composite particles for the smallest silica beads used. In every case, the composite particles could be easily separated from the free latex particles by centrifugation, providing a material made of regular core–shell composite particles. On the basis of the mechanisms involved in dispersion polymerization, hypotheses were formulated to account for the formation of the silica–polystyrene composite particles. Received: 6 May 1999 Accepted in revised form: 29 June 1999     

Preparation of poly(N-normalpropyl- acrylamide) gel beads

 The gel beads of N-normal-propylacrylamide are prepared by the radical copolymerization of N-normalpropylacrylamide and N,N′-methylene-bis-acrylamide in water. The optimum reaction conditions to obtain the gel beads are revealed from the phase diagram of the reaction system together with the scanning electron microscopy of the reaction products. The scanning electron microscopy of the reaction products also indicates the formation of the spherical gel beads of sub-micron size ranging from 250 to 500 nm in diameter. The viscosity measurements of the suspension of the gel beads indicate that the concentration dependence of the viscosity of the suspension is well described by Einstein’s theory of the viscosity of colloidal particles. The intrinsic viscosity of the suspension of gel beads is then determined. The density of the gel beads, which was obtained from the intrinsic viscosity of the suspension, indicates that the gel beads are in the swollen state at a temperature of 20 ^°C. Received: 12 September 1997 Accepted: 17 December 1997     

Morphology and electric conductivity of cross-linked polyethylene–carbon black blends prepared by gelation/ crystallization from solutions

 Ultra-high-molecular-weight polyethylene (UHMWPE) – carbon black (CB) blends were prepared by gelation/ crystallization from PE dilute solutions containing CB particles. The UHMWPE/CB composition chosen were 1/0.15, 1/0.25, 1/0.5, 1/0.75, 1/1, 1/3, 1/5, and 1/9, etc. The cross-linking of PE chains was performed by chemical reaction of dicumyl-peroxide at 160 ^°C. X-ray diffraction patterns indicate that the crystallinity of PE within the blends decreased drastically through the chemical reaction at high temperature. The sample preparation method by gelation/crystallization provided the UHMWPE–CB system with various CB contents up to 90% and the conductivities for the resultant specimens were in the range from 10^-9 to 1 Ω^-1 cm^-1 corresponding to the electric conductivity range of semiconductors. The blends assured thermal stability of electric conductivity by cross-linking of PE chains, although the mechanical property such as the storage and loss moduli were very sensitive to temperature. The conductivity of the blends with CB content ≥20% were almost independent of temperature up to 220 ^°C and the values in the heating and cooling processes were almost the same. On the other hand, for the UHMWPE–CB blends with 13% CB content corresponding to the critical one, temperature dependence of electric resistivity showed positive temperature coefficient (PTC) effect. The PTC intensities for non-cross-linked and cross-linked materials were lower than that of the corresponding low-molecular-weight-polyethylene (LMWPE)–CB blend but the maximum peak appeared at 160 ^°C which is higher than the peak temperature of LMWPE–CB blend. Received: 10 December 1997 Accepted: 9 April 1998     

Colloidal hydrolysis products of SbCl3 in acidic solutions

 The hydrolysis of SbCl₃ in hydrochloric acid solution (2.0 mol dm^-3 HCl) at 0 °C yields an amor-phous product consisting of uniform spherical particles (d∼0.5 μm), which on continuous aging at the same temperature transform to larger crystals, indicated by XRD to be Sb₄O₅Cl₂. In contrast, in the same solution kept at 25 °C crystalline particles of the same composition form directly after an induction period and then grow with time. The final products, obtained at 0 °C and 25 °C consist of aggregated subunits. These powders on calcination in nitrogen are converted to Sb₂O₃ and in air to Sb₂O₄. Received: 23 June 1997 Accepted: 1 July 1997     

Conductivities and silver electrode polarization resistance of solid electrolyte ceramics from ZrO2-Y2O3 powder synthesized in air plasma

Ceramic specimens have been obtained from the powder of ZrO₂-7.5 mol% Y₂O₃ having a specific surface area of 30 m²/g synthesized in air plasma. The novelty of this research lies in the fact that the plasma process makes it possible to prepare so-called nanopowders with a particle size less than 100 nm, possessing specific physical, chemical and technological properties. The sintered density of the specimens was 94–96% of the theoretical value, 6.001 g/cm³. The X-ray diffraction pattern of the specimens corresponded to a face-centered cubic lattice. Impedance in the frequency range of 100 Hz–15 MHz and d.c. polarization curves in a potential range of −10 to 10 mV were measured in the temperature range 200–850 °C in heating and cooling cycles. The intragrain, the grain boundary and the total bulk conductivities, the electrode polarization resistance and their activation energies were determined. The thermal stability of the studied system was proved in three measurement series up to 600–850 °C in heating and cooling cycles. The results obtained have shown that the conductivity of ZrO₂-7.5 mol% Y₂O₃ ceramics is not solely a function of temperature, but also depends on the previous thermal state of the ceramics. Received: 16 October 1997 / Accepted: 19 January 1998     

The application of the Wilhelmy balance to the measurement of electrocapillary effects in molten carbonate

In this work, the Wilhelmy method is shown to be very suitable for studying electrocapillary effects in molten salts. Unlike the optical methods usually used this method, can easily be used in automated set-ups. High accuracies of 0.3° in the contact angle were easily obtained. First experiments are reported on the electrocapillary effect on gold in molten carbonate under air. Small changes of 4° to 8° in the contact angle were found for potential excursions of –300 mV. At 650 °C a value of 65 ± 1° was obtained at Open Cell Voltage (OCV) which is in good accordance with the values found by Mugikura et al. and Matsumura et al. The wetting of gold by carbonate decreased at higher temperatures. In the literature, both positive and negative temperature effects have been reported, obtained in different gas atmospheres. Possibly the sign depends on the gas atmosphere used. However, this discrepancy can also be caused by differences in the characteristics of the gold surface used in the different studies. Received: 23 October 1997 / Accepted: 4 December 1997     

Properties of the forpolymer of N-vinylpyrrolidone with itaconic acid, acrylamide and 2-acrylamido-2-methyl-1-propane sulfonic acid as a fluid-loss reducer for drilling fluid at high temperatures

The forpolymer of N-vinylpyrrolidone (NVP), itaconic acid (IA), acrylamide (AM) and 2-acrylamido-2-methyl-1-propane sulfonic acid (AMPS) was synthesized through free-radical polymerization and was characterized using Fourier transform IR spectroscopy. The colloidal properties of the drilling fluid were investigated in the form of fresh-water or salt-water mud. It was found that the NVP–IA–AM–AMPS forpolymer had strong effects on the properties of the mud. The filtrate volume decreased with the increase of the forpolymer concentration before or after the aging test at 220 °C, and the filtrate volume after the aging test was larger than that before the aging test, but was still very small compared with the corresponding base mud. In addition, the rheological properties of both fresh-water mud and salt-water mud were modified by the forpolymer. The particle size data demonstrated that the average size of the clay particle after the aging test was larger than that before the aging test and that the particle size of the fresh-water mud was narrower compared with that of the salt-water mud before and after the aging test, respectively. The drilling fluid containing the forpolymer had an excellent tolerance to salt and high temperature. Received: 13 September 2000/Accepted: 9 January 2001