Studies of electroosmotic flow and the effects of protein adsorption in plasma‐polymerized microchannel surfaces

This paper presents a study of EOF properties of plasma‐polymerized microchannel surfaces and the effects of protein (fibrinogen and lysozyme) adsorption on the EOF behavior of the surface‐modified microchannels. Three plasma polymer surfaces, i.e. tetraglyme, acrylic acid and allylamine, are tested. Results indicate EOF suppression in all plasma‐coated channels compared with the uncoated glass microchannel surfaces. The EOF behaviors of the modified microchannels after exposure to protein solutions are also investigated and show that even low levels of protein adsorption can significantly influence EOF behavior, and in some cases, result in the reversal of flow. The results also highlight that EOF measurement can be used as a method for detecting the presence of proteins within microchannels at low surface coverage (<1 ng/cm² on glass). Critically, the results illustrate that the non‐fouling tetraglyme plasma polymer is able to sustain EOF. Comparison of the plasma‐polymerized surfaces with conventionally grafted polyelectrolyte surfaces demonstrates the stabilities of the plasma polymer films, enabling multiple EOF runs over 3 days without deterioration in performance. The results of this study clearly demonstrate that plasma polymers enable the surface chemistry of microfluidic devices to be tailored for specific applications. Critically, the deposition of the non‐fouling tetraglyme coating enables stable EOF to be induced in the presence of protein.     

Modification of the electrokinetic properties of reversible electrophoresis gels for the separation and preparation of DNA

The effect of adding linear polymers to a novel reversible electrophoretic was measured. Reversible gels are formed using the polyanionic carbohydrate polymer, gellan gum. Gellan gum forms strong stable gels in the presence of divalent cations or diamines. The gels are reversible (return to solution) by changing the ionic environment or pH. Gellan gum is an anionic polymer, and the electrophoresis gels have considerable electroosmotic flow (EOF) toward the negative electrode. We measured the EOF in gellan gum electrophoresis gels as a function of gel concentration, buffer composition, and linear polymer additive. The linear polymers used in this study were polyethylene oxide and hydroxyethyl cellulose. Both polymers reduced EOF in the gels, in a manner dependent on molecular weight. Polymers with high molecular weight were more effective at reducing EOF. The addition of polymers increased the resolution of low molecular weight DNA. Native gellan gum resolved DNA from approx 50,000 to 1000 bp. Addition of the polymers resolved DNA down to approx 50 bp, in some instances. The influence of the polymers on circular plasmid DNA was also investigated. Addition of high molecular weight polyethylene oxide reduced the electrophoretic mobility of the nicked circular form compared to the supercoiled form.     

What really enhances the adsorption of polymers onto chemically nonuniform surfaces: surface randomness or its heterogeneity?

We theoretically perform a comparative analysis of the adsorption of polymers onto the regularly and randomly nonuniform surfaces. By developing and making use of the self-consistent perturbation expansion we calculate the surface excesses of the polymers adsorbed on the random and periodically patterned surfaces. In both cases the enhancement of the polymer adsorption is indicated, as compared to the adsorption onto the homogeneous surface that has the same average affinity for polymers. Moreover, the results obtained for the randomly nonuniform and periodically patterned adsorbing surfaces show striking quantitative similarity, when compared at the same characteristic sizes of inhomogeneities of these surfaces. This finding leads to the conclusion that the adsorption ability of the nonuniform surface primarily depends on the characteristic size of the surface inhomogeneity, rather than on the spatial distribution of the inhomogeneities on this surface. In all cases, the calculated total surface excess is found to be a decaying function of the ratio of the radius of gyration of polymers to the characteristic size of the surface inhomogeneity. The effect of the excluded volume is found to reduce the polymer adsorption.     

Surface characterization using chemical force microscopy and the flow performance of modified polydimethylsiloxane for microfluidic device applications

The widespread interest in micro total analysis systems has resulted in efforts to develop devices in cheaper polymer materials such as polydimethylsiloxane (PDMS) as an alternative to expensive glass and silicon devices. We describe the oxidation of the PDMS surface to form ionizable groups using a discharge from a Tesla coil and subsequent chemical modification to augment electroosmotic flow (EOF) within the microfluidic devices. The flow performance of oxidized, amine-modified and unmodified PDMS materials has been determined and directly compared to conventional glass devices. Exact PDMS replicas of glass substrates were prepared using a novel two step micromolding protocol. Chemical force microscopy has been utilized to monitor and measure the efficacy of surface modification yielding information about the acid/base properties of the modified and unmodified surfaces. Results with different substrate materials correlates well with expected flow modifications as a result of surface modification. Oxidized PDMS devices were found to support faster EOF (twice that of native PDMS) similar to glass while those derivatized with 3-aminopropyl triethoxysilane (APTES) showed slower flow rates compared to native PDMS substrates as a result of masking surface charge. Results demonstrate that the surface of PDMS microdevices can be manipulated to control EOF characteristics using a facile surface derivatization methodology allowing surfaces to be tailored for specific microfluidic applications and characterized with chemical force microscopy.     

Multifunctional silane polymers for persistent surface derivatization and their antimicrobial properties

We demonstrate a versatile methodology combining both covalent surface anchoring and polymer cross-linking that is capable of forming long-lasting coatings on reactive and nonreactive surfaces. Polymers containing reactive methoxysilane groups form strong Si-O-Si links to oxide surfaces, thereby anchoring the polymer chains at multiple points. The interchain cross-linking of the methoxysilane groups provides additional durability to the coating and makes the coatings highly resistant to solvents. By tailoring the chemical structure of the polymer, we were able to control the surface energy (wetting) of a variety of surfaces over a wide range of water contact angles of 30-140 degrees . In addition, we synthesized covalently linked layer-by-layer polymeric assemblies from these novel methoxysilane polymers. Finally, antibacterial agents, such as silver bromide nanoparticles and triiodide ions, were introduced into these functional polymers to generate long-lasting and renewable antiseptic coatings on glass, metals, and textiles.     

Ligand-receptor interactions between surfaces: the role of binary polymer spacers

The interactions between a receptor-modified planar surface and a surface grafted with a bimodal polymer layer, where one of the polymer species is ligand functionalized, are studied using a molecular theory. The effects of changing the binding energy of the ligand-receptor pair, the polymer surface coverage, the composition, and molecular weight of both the unfunctionalized and ligand functionalized polymers on the interactions between the surfaces are investigated. Our findings show that bridging exists between the surfaces including when the molecular weight of the ligand-bearing polymer is smaller than that of the unfunctionalized polymer, even though the ligand is initially buried within the polymer layer. The distance at which the surfaces bind depends only on the molecular weight of the ligand-modified polymer, while the strength of the interaction at a given surface separation can be tuned by changing the molecular weight of the polymers, the total polymer surface coverage, and the fraction of ligated polymers. The composition of the bimodal layer alters the structure of the polymer layer, thereby influencing the strength of the steric repulsions between the surfaces. Our theoretical results show good agreement with experimental data. The present theoretical study can be used as guidelines for the design of surfaces with tailored abilities for tunning the binding strength and surface-ligand separation distances for polymer-grafted surfaces bearing specific targeting ligands.     

Grafting acrylic polymers from flat nickel and copper surfaces by surface-initiated atom transfer radical polymerization

Acrylic polymers, including poly(methyl methacrylate), poly(2,2,2-trifluoroethyl methacrylate), poly( N,N'-dimethyaminoethyl methacrylate), and poly(2-hydroxyethyl methacrylate) were grafted from flat nickel and copper surfaces through surface-initiated atom transfer radical polymerization (ATRP). For the nickel system, there was a linear relationship between polymer layer thickness and monomer conversion or molecular weight of "free" polymers. The thickness of the polymer brush films was greater than 80 nm after 6 h of reaction time. The grafting density was estimated to be 0.40 chains/nm2. The "living" chain ends of grafted polymers were still active and initiated the growth of a second block of polymer. Block copolymer brushes with different block sequences were successfully prepared. The experimental surface chemical compositions as measured by X-ray photoelectron spectroscopy agreed very well with their theoretical values. Water contact angle measurements further confirmed the successful grafting of polymers from nickel and copper surfaces. The surface morphologies of all samples were studied by atomic force microscopy. This study provided a novel approach to prepare stable functional polymer coatings on reactive metal surfaces.     

Self-assembled epoxy-modified polymer coating on a poly(dimethylsiloxane) microchip for EOF inhibition and biopolymers separation

A straightforward approach to generate a stable and protein-resistant poly(dimethylsiloxane) (PDMS) surface using self-assembled hydrophilic polymers is demonstrated in this work. Epoxy-modified polymers were directly adsorbed from aqueous solution onto plasma oxidized PDMS based on H-bond interaction, and epoxies of polymer and silanols on oxidized PDMS surface were crosslinked by heating at 110 degrees C. The coating process could be completed within half hour. Poly(dimethylacrylamide-co-glycidyl methacrylate) (PDMA-co-GMA), poly(vinyl pyrrolidone)-g-glycidyl methacrylate (PVP-g-GMA) and poly(vinyl alcohol)-g-glycidyl methacrylate (PVA-g-GMA) (D. P. Wu, B. X. Zhao, Z. P. Dai, J. H. Qin and B. C. Lin, Lab Chip, 2006, 6, 942) were employed as examples here. Unlike PDMA, PVP, and PVA themselves, these epoxy-modified hydrophilic polymers could be directly used as static surface coatings on oxidized PDMS, and inhibited electroosmotic flow (EOF) within pH 3-11. It was also found that hard baking of PDMS at 150 degrees C for 24 hours before surface coating could greatly retard surface hydrophobicity recovery after oxygen plasma exposure, which strengthened epoxy-modified polymer coatings on oxidized PDMS surface, and resulted in EOF less than 0.2 x 10(-4) cm(2) V(-1) s(-1) (pH 9.0) within two weeks. On epoxy-modified polymer coated PDMS microchips, basic proteins, peptides and DNA fragments could be separated satisfactorily, in which more than 2 x 10(4) plates per 2 cm and less than 3% RSD (>8 runs) for migration time were obtained for lysozyme.     

Confinement free energy of surfaces bearing end-grafted polymers in the mushroom regime and local measurement of the polymer density

End-tethered polymer chains usually adopt mushroomlike structures on the surface when their density is low. The behaviors of these surface-attached hemicoils are described by existing polymer theory. Dolan and Edwards derived the free energy of a single polymer chain confined between two planar surfaces. Their theory was used to approximate the steric interaction free energy, E, of two identical surfaces bearing polymers in the mushroom regime and to compare with experimental data obtained from surface force measurements. However, because of a mislabeled plot in the original paper, experimental force profiles did not seem to fit the free energy approximation satisfactorily. We have correctly relabeled the involved plot and derived a new simple expression for E. In order to verify this expression, we have performed experiments on PEG45 polymers incorporated in lipid bilayers using a surface force apparatus. The measured force profiles are in perfect agreement with the prediction. We show that such measurements can be used to determine the local density of grafted polymer with good precision.     

Potential of prodendronic polyamines with modulated segmental charge density as novel coating for fast and efficient analysis of peptides and basic proteins by CE and CE‐MS

In this work, the suitability of a new polymer family has been investigated as capillary coatings for the analysis of peptides and basic proteins by CE. This polymer family has been designed to minimize or completely prevent protein–capillary wall interactions and to modify the EOF. These coating materials are linear polymeric chains bearing as side cationizable moiety a dentronic triamine derived from N,N,N’,N’‐tetraethyldiethylenetriamine (TEDETA), which is linked to the backbone through a spacer (unit labeled as TEDETAMA). Four different polymers have been prepared and evaluated: a homopolymer which comprised only of those cationizable repetitive units of TEDETAMA, and three copolymers that randomly incorporate TEDETAMA together with neutral hydrosoluble units of N‐(2‐hydroxypropyl) methacrylamide (HPMA) at different molar percentages (25:75, 50:50 and 75:25). It has been demonstrated that the composition of the copolymers influences the EOF and therefore the separation of the investigated biopolymers. Among the novel polymers studied, poly‐(TEDETAMA‐co‐HPMA) 50:50 copolymer was successfully applied as coating material of the inner capillary surface in CE‐UV and CE‐MS, providing EOF reversing together with fast and efficient baseline separation of peptides and basic proteins. Finally, the feasibility of the polymer‐coated capillary was shown through the analysis of lysozyme in a cheese sample.     

Direct measurement of shear forces between polymer-bearing surfaces sliding past each other

We have used a recently developed surface force balance to measure, with extreme sensitivity, both lateral and normal forces between interacting surfaces, for the case of simple liquids and particularly with surface-attached polymers. The presence of polymers on the surfaces reduces drastically the force required to maintain them in sliding motion, under a given normal load, relative to the bare surface case. We believe this is due to the long range steric repulsion which can sustain a large normal load while maintaining a very fluid interfacial layer. The effect is much more marked for end-tethered chains in a good solvent than for adsorbed chains in a θ-solvent. This is attributed to the different extents of interpenetration of the compressed polymer layers.     

Grafting epoxy-modified hydrophilic polymers onto poly(dimethylsiloxane) microfluidic chip to resist nonspecific protein adsorption

In order to achieve a simple covalent hydrophilic polymer coating on poly(dimethylsiloxane) (PDMS) microfluidic chip, epoxy modified hydrophilic polymers were synthesized in aqueous solution with a persulfate radical initiation system, and crosslinked onto PDMS pretreated by oxygen plasma and silanized with 3-aminopropyl-triethoxysilanes (APTES). Glycidyl methacrylate (GMA) was copolymerized with acrylamide (poly(AAM-co-GMA)) or dimethylacrylamide (poly(DAM-co-GMA)), and graft polymerized with polyvinylpyrrolidone (PVP-g-GMA) or polyvinylalcohol (PVA-g-GMA). The epoxy groups in the polymers were determined by UV spectra after derivation with benzylamine. Reflection absorption infrared spectroscopy (RAIRS) confirmed covalent grafting of GMA-modified polymers onto PDMS surface. Electroosmotic flow (EOF) in the polymer grafted microchannel was strongly suppressed within the range pH 3-11. Surface adsorption of lysozyme and bovine serum albumin (BSA) was reduced to less than 10% relative to that on the native PDMS surface. On the GMA-modified polymer coated PDMS microchip, basic proteins, peptides, and sodium dodecyl sulfate (SDS) denatured proteins were separated successfully.     

Single-step process to produce surface-functionalized polymeric nanoparticles

Nanoparticles (NPs) are a versatile medium for the localization of therapeutics to tumors and for cellular and tissue imaging. The ability to impart targeting capability or enhance cellular uptake is dependent in part on the presentation of relevant surface functionality, among other design parameters. Currently, the production of functionalized polymeric NPs requires the a priori synthesis of polymers bearing such functionality. Here we describe a process to produce functionalized polymeric NPs derived from nonfunctional polymers in a single step. This was achieved by tailoring the solvation of the polymer using a binary solvent system such that the addition of an aqueous phase rich in water-soluble polymer or polyelectrolytes results in the formation of NPs with the concomitant functionalization of NP surfaces with the polymeric moieties introduced into the aqueous phase. This strategy also allows for easy control over NP size independent of surface functionality. We have demonstrated that poly(lactic-co-glycolic acid) (PLGA) NPs bearing surface functionality as diverse as biological polysaccharides such as heparin, water-soluble ionic polymers, and poly(ethylene glycol) can be prepared under identical conditions in a single step, with surface coverage (mass %) ranging from 3 to >70%. We expect this novel process to enable complex surface engineering of NP chemistry that hitherto was impossible using existing approaches.     

Adhesion and proliferation of cells on new polymers modified biomaterials

Up to today, several techniques have been used to maintain cells in culture for studying many aspects of cell biology and physiology. More often, cell culture is dependent on proper anchorage of cells to the growth surface. Poly-l-lysine is commonly used as adhesive molecule. In this study, we present, as an alternative to poly-l-lysine, new polymer film substrates, realized by electropolymerization of different monomers on fluorine-doped tin oxide (FTO) surfaces since electropolymerization is a good method to coat selectively metallic or semiconducting electrodes with polymer films. So, the adhesion, proliferation and morphology of rat neuronal cell lines were investigated on polymer treated surfaces. Several amine-based biocompatible polymers were tested: polyethyleneimine (PEI), polypropyleneimine (PPI), polypyrrole (PPy) and poly(p-phenylenediamine) (PPPD). These polymer films were coated on FTO surfaces by electrochemical oxidation. After 8 h in a culture medium, a high percentage of cells was found to be attached to PEI and PPI compared to the other polymers and to the reference surfaces (glass and FTO uncovered). After 24 and 72 h in the culture medium, cells were found to proliferate faster on PEI and PPI than on other polymers and reference surfaces. Consequently, cells have a greater fold expansion on PEI and PPI than on PPPD, PPy or glass and FTO uncoated. From these results, we deduce that PEI and PPI can be useful as coating surface to cultivate neuronal cells.     

Influence of polymer structure on electroosmotic flow and separation efficiency in successive multiple ionic layer coatings for microchip electrophoresis

The effect of successive multiple ionic layer (SMIL) coatings on the velocity and direction of EOF and the separation efficiency for PDMS electrophoresis microchips was studied using different polymer structures and deposition conditions. To date, the majority of SMIL studies have used traditional CE and fused-silica capillaries. EOF was measured as a function of polymer structure and number of layers, in one case using the same anionic polymer and varying the cationic polymer and in the second case using the same cationic polymer and varying the anionic polymer. In both situations, the EOF direction reversed with each additional deposited polymer layer. The absolute EOF magnitude, however, did not vary significantly with layer number or polymer structure. Next, different coatings were used to compare separation efficiencies on native and SMIL-coated PDMS microchips. For native PDMS microchips, the average separation efficiency was 4105 +/- 1540 theoretical plates. The addition of two layers of polymer increased the separation efficiency anywhere from two- to five-fold, depending on the polymer structure. A maximum separation efficiency of 12 880 +/- 1050 theoretical plates was achieved for SMIL coatings of polybrene (cationic) and dextran sulfate (anionic) polymers after deposition of six total layers. It was also noted that coating improved run-to-run consistency of the peaks as noted by a reduction of the RSD of the EOF and separation efficiency. This study shows that the use of polyelectrolyte coatings, irrespective of the polymer structure, generates a consistent EOF in the current experiments and dramatically improves the separation efficiency when compared to unmodified PDMS microchips.     

Contact angles as indicators of the polymer surface structure

The capacities of the wetting method for the characterization of the surface structure of polymers and surfactant adsorption layers on polymer surfaces and also the determination of the energy characteristics of polymer surfaces at different interfaces, which are used to optimize the choice of polymers in the solution of actual practical problems, are demonstrated.     

Molecular dynamics simulations of polyelectrolyte adsorption

We have performed molecular dynamics simulations of polyelectrolyte adsorption at oppositely charged surfaces from dilute polyelectrolyte solutions. In our simulations, polyelectrolytes were modeled by chains of charged Lennard-Jones particles with explicit counterions. We have studied the effects of the surface charge density, surface charge distribution, solvent quality for the polymer backbone, strength of the short-range interactions between polymers and substrates on the polymer surface coverage, and the thickness of the adsorbed layer. The polymer surface coverage monotonically increases with increasing surface charge density for almost all studied systems except for the system of hydrophilic polyelectrolytes adsorbing at hydrophilic surfaces. In this case the polymer surface coverage saturates at high surface charge densities. This is due to additional monomer-monomer repulsion between adsorbed polymer chains, which becomes important in dense polymeric layers. These interactions also preclude surface overcharging by hydrophilic polyelectrolytes at high surface charge densities. The thickness of the adsorbed layer shows monotonic dependence on the surface charge density for the systems of hydrophobic polyelectrolytes for both hydrophobic and hydrophilic surfaces. Thickness is a decreasing function of the surface charge density in the case of hydrophilic surfaces while it increases with the surface charge density for hydrophobic substrates. Qualitatively different behavior is observed for the thickness of the adsorbed layer of hydrophilic polyelectrolytes at hydrophilic surfaces. In this case, thickness first decreases with increasing surface charge density, then it begins to increase.     

Surface-grafting of phosphates onto a polymer for potential biomimetic functionalization of biomaterials

In the human body, phosphate groups play important roles in signaling and the biological functions of proteins and peptides. Despite the importance of phosphate groups, polymer surfaces have not been directly grafted with phosphate groups by chemical reactions because the usual organic solvents used to graft phosphate groups can dissolve or swell polymers. We focused this study on grafting phosphate groups onto a poly(ethylene-co-acrylic acid) (PEAA) surface in an aqueous solution. O-phospho L-serine and O-phosphoethanolamine were grafted on PEAA surfaces to introduce phosphate groups by activating carboxylic acid groups of PEAA using N-hydroxysuccinimide (NHS) and 1-ethyl-3-(3-dimethylaminopropyl)carbodiimide (EDC) in an aqueous environment. X-ray photoelectron spectroscopy (XPS) was used to elucidate the process by which surface grafting occurs and the process that the phosphate group is cleaved into a phosphate ion and a hydrolyzed molecule at high pH. It was found that under appropriate reaction conditions the phosphate groups could be successfully grafted on the polymer surfaces. The phosphate-grafted polymer surfaces showed lower water contact angles than the initial polymer surfaces likely due to their highly mobile and hydrophilic phosphate side groups. This work demonstrates a technique to successfully graft phosphate groups onto organic polymer surfaces in a biocompatible aqueous environment, which may open new avenues to functionalizing synthetic polymeric and natural macromolecule derived biomaterials.     

DNA-conjugated polymers for self-assembled DNA chip fabrication.

We developed two DNA-conjugated polymers, one based on polyallylamine and the other on polyacrylic acid, for use in DNA chips. A 30-mer single-stranded DNA probe and thioctic acid were covalently attached to polyallylamine as sidechains. The same single-stranded DNA and 3-(pyridyldithio)propionyl hydrazide were covalently attached to polyacrylic acid as sidechains. Both DNA-conjugated polymers could be specifically immobilized onto a gold sensor substrate by a self-assembly technique. The interactions between fully matched DNA and each DNA-conjugated polymer were investigated by surface plasmon resonance. A gold surface modified with either DNA-conjugated polymer recognized fully matched DNA much better than unmatched DNA. The hybridization selectivity and efficiency of DNA-conjugated polyallylamine was optimized by adjusting the pH so as to reduce the effects of cationic polymer sidechains. The hybridization selectivity and efficiency of DNA-conjugated polymers were higher than those of a conventional immobilized thiol-based DNA. The coating of DNA-conjugated polymers reduced nonspecific adsorption of DNA by the gold substrate. DNA-conjugated polyacrylic acid was more selective toward fully matched DNA than was DNA-conjugated polyallylamine. Therefore, DNA-conjugated polymers show promise for application in novel DNA chips.     

Surface modification on microfluidic devices with 2-methacryloyloxyethyl phosphorylcholine polymers for reducing unfavorable protein adsorption

Surface modification of polymer materials for preparing microfluidic devices including poly(dimethyl siloxane) (PDMS) was investigated with phospholipids polymers such as poly(2-methacryloyloxylethyl phosphorylcholine(MPC)-co-n-butyl methacrylate) (PMB) and poly(MPC-co-2-ethylhexyl methacrylate-co-2-(N,N-dimethylamino)ethyl methacrylate) (PMED). The hydrophilicity of every surface on the polymer materials modified with these MPC polymers increased and the value of zeta-potential became close to zero. The protein adsorption on the polymer materials with and without the surface modification was evaluated using a protein mixture of human plasma fibrinogen and serum albumin. Amount of proteins adsorbed on these polymeric materials showed significant reduction by the surface modification with the MPC polymers compared to the uncoated surfaces ranging from 56 to 90%. Furthermore, we successfully prepared PDMS-based microchannel which was modified by simple coating with the PMB and PMED. The modified microchannel also revealed a significant reduction of adsorption of serum albumin. We conclude that the MPC polymers are useful for reducing unfavorable protein adsorption on microfluidic devices.