用于白光LED的高亮度蓝白色荧光粉Ca2SiO3Cl2：Eu2+的发光性质

采用固相法在较低温度下合成了Eu²⁺激活的Ca₂SiO₃Cl₂高亮度蓝白色发光材料,并对其发光性质进行了研究。其发射光谱由两个谱带组成,峰值分别位于420,498nm处,归结为Ca₂SiO₃Cl₂晶体中占据两种不同Ca²⁺格位的Eu²⁺离子的5d→4f跃迁发射。改变Eu²⁺浓度,可以使样品的发光在蓝白色和绿白色之间变化。当Eu²⁺浓度为0.005mol^-1时,样品呈现很亮的蓝白色发光。两个发射峰的激发光谱均分布在250~410nm的波长范围内,峰值分别位于333,369nm处。Ca₂SiO₃Cl₂:Eu²⁺可被InGaN管芯产生的近紫外辐射有效激发,是一种性能良好的白光LED用单一基质蓝白色荧光粉。     

Eu2+掺杂浓度对Ca2MgSi2O7∶Eu2+荧光粉发光特性的影响

采用化学共沉淀法制备了Ca_2-xMgSi₂O₇:xEu²⁺绿色荧光粉.用X射线衍射仪、荧光分光光度计及光色综合测试系统对Ca_2-xMgSi₂O₇:xEu²⁺绿色荧光粉的相结构、发光性能进行了测试.结果表明:其激发光谱分布在300–480 nm波长范围,谱峰位于389,430 nm处,可以被InGaN管芯产生的360–480 nm辐射有效激发;在波长为430 nm蓝光激发下,其发射光谱谱峰位于531 nm处.Ca_2-xMgSi₂O₇:xEu²⁺绿色荧光粉的发光强度随Eu²⁺掺杂量的增加而增强,当Eu²⁺掺杂量x为0.04时,发光强度达到最大值,而后开始降低,发生浓度猝灭.根据Dexter能量共振理论,浓度猝灭是由电偶极-电偶极相互作用引起的. 关键词： 2MgSi₂O₇∶Eu²⁺')" href="#">Ca₂MgSi₂O₇∶Eu²⁺ 绿色荧光粉 发光特性 白光发光二极管     

Ca2GeO4 ∶Eu3+ 的电子结构和紫外-真空紫外发光特性的研究

采用高温固相法合成了发光材料Ca₂GeO₄ ∶Eu³⁺ ,并详细研究了其紫外-真空紫外发光特性. 发现并解释了Eu³⁺ 离子在空气中的自还原以及在不同波长激发下的颜色转换现象. Ca₂GeO₄ ∶Eu³⁺ 在163—230和301,466 nm处具有强激发带,表明Ca₂GeO₄ ∶Eu³⁺ 关键词： 2GeO₄ ∶Eu³⁺')" href="#">Ca₂GeO₄ ∶Eu³⁺ 光致发光机理 空气中自还原 颜色转换     

Eu2+,Mn2+在BaZnP2O7中的发光及Eu2+→Mn2+能量传递

采用高温固相法合成了BaZnP₂O₇:Eu²⁺,Mn²⁺荧光粉,并对其发光性质及Eu²⁺对Mn²⁺的能量传递机理进行了研究.Eu²⁺和Mn²⁺在380 nm和670nm的发射峰分别由Eu²⁺的5d—4f跃迁和Mn²⁺的⁴T₁(^{4关键词： 磷酸盐 2+}')" href="#">Eu²⁺ 2+')" href="#">Mn²⁺ 能量传递     

Ca$lt;sub$gt;2$lt;/sub$gt;Si（O$lt;sub$gt;4-$lt;i$gt;x$lt;/i$gt;$lt;/sub$gt;N$lt;sub$gt;$lt;i$gt;x$lt;/i$gt;$lt;/sub$gt;）：Eu$lt;sup$gt;2+$lt;/sup$gt;绿色荧光粉的制备及其发光性能

利用在Ca-Si-O干凝胶前驱体中添加Si₃N₄的方法于非还原气氛下合成了含N固溶体Ca₂Si（O_4-xN_x）：Eu²⁺绿色荧光粉. 通过X射线衍射仪、扫描电子显微镜以及荧光分光光度计分别分析了产物的物相结构、颗粒形貌和发光性能. 结果显示,Si₃N₄与前驱体的混合物在非还原气氛（纯氮气）下于1100℃焙烧后获得含N固溶体Ca₂Si（O_4-xN_x）：Eu²⁺荧光粉,特别是其中Eu³⁺被还原为Eu²⁺,产物的晶体结构与βup -Ca₂SiO₄相一致. Ca₂Si（O_4-xN_x）：Eu²⁺能够被270–400 nm 范围内的紫外线有效激发,其发射光谱呈宽带发射. 随着N含量的增加,发射峰出现一定程度红移（501–504 nm）,而且发光强度显著提高. 当Eu²⁺浓度为0.25 mol%时发光强度达最大值,浓度超过0.25 mol%时,发光强度显著降低,出现浓度猝灭 效应. 关键词： 白光LED 荧光粉 溶胶凝胶法 3N₄')" href="#">Si₃N₄     

Li+和Er3+掺杂对Ba2SiO4：Eu2+发光性能的影响

采用化学沉淀法一次煅烧工艺制备了Ba_1.99-x/2-2ySiO₄:Eu_0.01²⁺, Li_x+y²⁺, Eu_y³⁺绿色荧光粉, 用X射线衍射仪和荧光分光光度计对样品的晶体结构、发光性能进行表征. 结果表明: 少量Eu²⁺, Li⁺和Er³⁺的共掺杂没有改变晶体结构; 其激发光谱分布在270–440 nm波长范围, 谱峰位于288 nm, 360 nm处, 可以被InGaN 管芯产生的360–410 nm辐射有效激发; 在360 nm近紫外光激发下, 测得其发射光谱峰值在500 nm 处, 是Eu²⁺4f⁶5d¹→4f⁷跃迁的典型发射; 荧光粉发光强度随着Li⁺掺杂量的增大先增强, 后减弱, 当x=0.1时, 发光强度最大; 随着Li⁺, Er³⁺共掺杂量的增加(y=0.012), 出现位于530 nm和488 nm的发射峰, 对应于Er³⁺的²H_11/2→⁴I_15/2和⁴F_7/2→⁴I_15/2特征发射, 同时分析了Eu²⁺→Er³⁺的能量传递过程. 关键词： 化学沉淀法 2SiO₄：Eu²⁺,Li⁺,Er³⁺')" href="#">Ba₂SiO₄：Eu²⁺,Li⁺,Er³⁺ 能量传递 发光性能     

MgO对Sr2SiO4:Eu2+荧光粉发光性质的影响

通过在Sr₂SiO₄:Eu²⁺荧光粉中加入MgO,提高了Sr₂SiO₄:Eu²⁺荧光粉的蓝光和黄光发射带的发射强度,研究了MgO浓度对Sr₂SiO₄:Eu²⁺荧光粉发光强度的影响。当Mg与Si的量比在1.0附近时,荧光粉的亮度较高,且发光颜色为白色。通过调节Sr₂SiO₄:yEu²⁺ ,MgO荧光粉中Eu²⁺的掺杂浓度,可以调节荧光粉的发光颜色。用Sr₂SiO₄:Eu²⁺ ,MgO和400 nm的InGaN管芯制备的白光LED,色坐标优于α'-Sr₂SiO₄:Eu²⁺和β-Sr₂SiO₄:Eu²⁺荧光粉制成的白光LED,显色指数和流明效率高于β-Sr₂SiO₄:Eu²⁺和α'-Sr₂SiO₄:Eu²⁺制成的白光LED。     

Ca2SiO4:Dy3+材料的制备及其发光特性

采用高温固相法制备了Ca₂SiO₄:Dy³⁺发光材料.在365nm紫外光激发下,测得Ca₂SiO₄:Dy³⁺材料的发射光谱为一多峰宽谱,主峰分别位于486nm,575nm和665nm处;监测575nm发射峰,测得材料的激发光谱为一多峰宽谱,主峰分别位于331nm,361nm,371nm,397nm,435nm,461nm和478nm处.研究了Dy³⁺掺杂浓度对Ca₂SiO₄:Dy³⁺材料发射光谱及发光强度的影响,结果显示,随Dy³⁺浓度的增大,黄、蓝发射峰强度比(Y/B)逐渐增大,利用Judd-Ofelt理论解释了其原因;随Dy³⁺浓度的增大,Ca₂SiO₄:Dy³⁺材料发光强度先增大,在Dy³⁺浓度为4 mol%时到达峰值,而后减小,根据Dexter理论其浓度猝灭机理为电偶极-电偶极相互作用.研究了电荷补偿剂Li⁺,Na⁺和K⁺对Ca₂SiO₄:Dy³⁺材料发射光谱的影响,结果显示,不同电荷补偿剂下,随电荷补偿剂掺杂浓度的增大,Ca₂SiO₄:Dy³⁺材料发射光谱强度的演化趋势相同,即Ca₂SiO₄:Dy³⁺材料发射峰强度先增大后减小,但不同电荷补偿剂下,材料发射峰强度最大处对应的补偿剂浓度不同,对应Li⁺,Na⁺和K⁺时,浓度分别为4mol%,4mol%和3mol%. 关键词： 白光LED 2SiO₄:Dy³⁺')" href="#">Ca₂SiO₄:Dy³⁺ 发光特性 电荷补偿     

H3BO3对BaAl2Si2O8：Eu2+蓝色荧光粉物相组成和发光特性的影响

采用化学共沉淀法一次煅烧工艺合成了BaAl₂Si₂O₈：Eu²⁺蓝色荧光粉.用X射线衍射仪、荧光分光光度计和扫描电镜测试了助熔剂H₃BO₃对BaAl₂Si₂O₈：Eu²⁺蓝色荧光粉物相结构、发光性能、形貌等的影响.研究表明：化学共沉淀法一次煅烧工艺合成的BaAl₂Si₂O₈：Eu²⁺蓝色荧光粉为单相,H₃BO₃的加入使基质结构由六方相转变成单斜相,并引起发射主峰位置和发射强度的变化;BaAl₂Si₂O₈：Eu²⁺蓝色荧光粉的发光强度随着H₃BO₃加入量的增加先增强,后减弱,当加入H₃BO₃的质量分数为1.5%时,发光强度最大;H₃BO₃的加入使合成BaAl₂Si₂O₈：Eu²⁺蓝色荧光粉的颗粒呈类球形,分布更加均匀,粒度更小. 关键词： 3BO₃')" href="#">H₃BO₃ 2Si₂O₈：Eu²⁺')" href="#">BaAl₂Si₂O₈：Eu²⁺ 发光特性 化学共沉淀法     

Sr2+掺杂荧光粉Ca2Nb2O7：Eu3+的发光特性

采用高温固相法制备出Ca_1.97-xSr_xNb₂O₇：3%Eu³⁺（x=0.10,0.50,1.0,1.5,1.97）红色荧光粉,研究了Ca_1.97-xSr_xNb₂O₇：3%Eu³⁺的发光特性及Sr²⁺的浓度对该荧光粉发光性质的影响。随着Sr²⁺浓度的改变,Ca_2-xSr_xNb₂O₇：Eu³⁺的XRD呈现不同的相。Ca_1.97Nb₂O₇：3%Eu³⁺（x=0）的激发光谱中,302 nm附近的强宽带来自于O^2-→Eu³⁺电荷转移跃迁,272 nm附近的肩峰来自于NbO^7-₆基团的电荷转移跃迁,350~600 nm范围内的锐锋属于Eu³⁺的特征4f-4f组内跃迁。在398 nm激发下,发射光谱的最强峰位于616 nm,属于Eu³⁺的⁵D₀→⁷F₂电偶极跃迁,发射出强烈的红光。当Ca²⁺逐渐被Sr²⁺取代时,Ca_2-xSr_xNb₂O₇：Eu³⁺的各激发峰的强度先提高后降低,且O^2-→Eu³⁺电荷转移跃迁发生明显红移。少量Sr²⁺的掺杂可以有效提高Ca_2-xSr_xNb₂O₇：Eu³⁺ 的红光发射强度,当x=0.01时该荧光粉的红光发射达到最强,可以被紫外LED芯片激发。     

用于白光LED的单一基质白光荧光粉Ca2SiO3Cl2:Eu2+，Mn2+的发光性质

用高温固相法合成了Eu²⁺，Mn²⁺共激活的Ca₂SiO₃Cl₂高亮度白色发光材料，并对其发光性质进行了研究. 该荧光粉在近紫外光激发下发出强的白色荧光，Eu^{2+中心形成峰值为419 nm和498 nm的特征宽带，通过Eu2+中心向Mn2+中心的能量传递导致了峰值为578 nm的发射，三个谱带叠加从而在单一基质中得到了白光. 激发光谱均分布在250—415 nm的波长范围，红绿蓝三个发射带的激发谱峰值分别位于385 nm，412 nm，370 nm和396 nm处，可以被InGaN管芯产生的紫外辐射有效激发. Ca₂SiO₃Cl₂:Eu2+，Mn2+是一种很有前途的单一基质白光LED荧光粉.}     

Intense green/yellow emission in Ca8Zn(SiO4)4Cl2:Eu, Mn through energy transfer for blue-LED lighting

Eu²⁺ and Mn²⁺ co-doped Ca₈Zn(SiO₄)₄Cl₂ phosphors have been synthesized by a high temperature solid state reaction. Energy transfer from Eu²⁺ to Mn²⁺ is observed. The emission spectra of the phosphors show a green band at 505 nm of Eu²⁺ and a yellow band at 550 nm of Mn²⁺. The excitation spectra corresponding to 4f⁷-4f⁶5d transition of Eu²⁺ cover the spectral range of 370-470 nm, well matching UV and/or blue LEDs. The shortening of fluorescent lifetimes of Eu²⁺ followed by simultaneous increase of fluorescent intensity of Mn²⁺ with increasing Mn²⁺ concentrations is studied based on energy transfer. Upon blue light excitation the present phosphor can emit intense green/yellow in comparison with other chlorosilicate phosphors such as Eu²⁺ and Mn²⁺ co-doped Ca₈Mg(SiO₄)₄Cl₂ and Ca₃SiO₄Cl₂, demonstrating a potential application in phosphor converted white LEDs.     

Luminescence characteristics of Eu2+ activated Ca2SiO4 Sr2SiO4 and Ba2SiO4 phosphorsfor white LEDs

<正>This paper investigates the luminescence characteristics of Eu²⁺ activated Ca₂SiO₄,Sr₂SiO₄ and Ba₂SiO₄ phosphors. Two emission bands are assigned to the f-d transitions of Eu²⁺ ions doped into two different cation sites in host lattices,and show different emission colour variation caused by substituting M²⁺ cations for smaller cations.This behaviour is discussed in terms of two competing factors of the crystal field strength and covalence.These phosphors with maximum excitation of around 370 nm can be applied as a colour-tunable phosphor for light-emitting diodes（LEDs） based on ultraviolet chip/phosphor technology.     

Synthesis, luminescence and crystallographic structure of Eu-doped garnet-type yafsoanite Ca3Te2(ZnO4)3

A red-emitting phosphor of Eu³⁺-doped calcium–tellurium–zinc oxide, Ca₃Te₂(ZnO₄)₃, with a garnet-type structure was synthesized by high temperature solid-state reactions. This phosphor exhibited a strong red emission. The photoluminescence excitation spectrum showed that Ca₃Te₂(ZnO₄)₃:Eu³⁺ can be effectively excited by UV–visible light. The property of long-wavelength excitation for this material has a benefit as a red phosphor in application of white light-emitting diodes. The colour coordinates were calculated. The excitation and emission spectra and luminescence decay curves were obtained using a pulsed, tunable, narrowband dye laser. Crystallographic sites and charge compensation mechanism of Eu³⁺ ions were discussed. The emission line from Eu³⁺ in intrinsic crystallographic site in the lattice was located at 579.56 nm. The emission line from Eu³⁺ in another disturbed site, which is created by the defects created by the charge-compensation, was located at 580.88 nm. The disordered crystallographic sites of Eu³⁺ are benefit for their strong red luminescence corresponding to the ⁵D₀→⁷F₂ transition.     

White light-emitting Mg0.1Sr1.9SiO4:Eu phosphors

Divalent europium-activated strontium orthosilicate Sr₂SiO₄:Eu²⁺ and Mg_0.1Sr_1.9SiO₄:Eu²⁺ phosphors were synthesized through the solid-state reaction technique. Their luminescent properties under ultraviolet excitation were investigated. The X-ray diffraction (XRD) results show that these phosphors are of α′-Sr₂SiO₄ phase with a trace of β-Sr₂SiO₄. Doping of Eu²⁺ ion into the crystal lattice results in the lattice constant being expended, while Mg²⁺ makes the lattice constant shrinking. A solid solution with the same crystal structure is formed when Eu²⁺ or Mg²⁺ substitutes part of Sr²⁺ ions and occupies the same lattice sites. The Sr₂SiO₄:Eu²⁺ phosphors show two emission spectra peaked at 535 and 473 nm originated from the 5d-4f transition of Eu²⁺ ion doped in two different Sr²⁺ sites in the host lattice. By substitution of 0.1 mol of Sr²⁺ with Mg²⁺, these two emission bands are tuned to be in the blue and yellow region (459 and 564 nm for Mg_0.1Sr_1.88SiO₄:Eu_0.02), respectively. The tuning effect is discussed. With a combination of the blue and yellow emission bands the phosphors show white color, indicating that these phosphors may become promising phosphor candidates for white light-emitting diodes (LEDs).     

Sr和Ba替代对Eu掺杂Ca2.955Si2O7的结构和发光特性的影响研究

利用固相反应法制备了Sr和Ba替代的Ca_2.955-xM_xSi₂O₇: 0.045Eu²⁺ (M= Sr, Ba, x= 0.1-0.5)系列荧光粉, 利用较大离子半径的Sr和Ba元素替代Eu掺杂Ca_2.955-xM_xSi₂O₇ 中的Ca元素,研究Sr和Ba替代对样品结构和发光特性的影响. X射线衍射测试结果表明,少量Sr和Ba替代不会改变基质的晶体结构, 样品仍然为单斜晶系.未替代前, Ca_2.955Si₂O₇: 0.045Eu²⁺ 样品的发射峰在574 nm左右,随着Sr含量的增加,样品的发射峰发生蓝移; 而Ba含量在x= 0.1-0.4时不会引起发射峰位置的移动, 但x= 0.5样品的发射峰发生蓝移.同等含量的Sr和Ba部分替代样品中的Ca元素, Ba替代样品的光谱强度较强.     

A white light emitting phosphor Sr1.5Ca0.5SiO4:Eu, Tb, Eu for LED-based near-UV chip: Preparation, characterization and luminescent mechanism

In this work, we report preparation, characterization and luminescent mechanism of a phosphor Sr_1.5Ca_0.5SiO₄:Eu³⁺,Tb³⁺,Eu²⁺ (SCS:ETE) for white-light emitting diode (W-LED)-based near-UV chip. Co-doped rare earth cations Eu³⁺, Tb³⁺ and Eu²⁺ as aggregated luminescent centers within the orthosilicate host in a controlled manner resulted in the white-light phosphors with tunable emission properties. Under the excitation of near-UV light (394 nm), the emission spectra of these phosphors exhibited three emission bands: one broad band in the blue area, a second band with sharp lines peaked in green (about 548 nm) and the third band in the orange-red region (588-720 nm). These bands originated from Eu²⁺ 5d→4f, Tb³⁺⁵D₄→⁷F_J and Eu³⁺⁵D₀→⁷F_J transitions, respectively, with comparable intensities, which in return resulted in white light emission. With anincrease of Tb³⁺ content, both broad Eu²⁺ emission and sharp Eu³⁺ emission increase. The former may be understood by the reduction mechanism due to the charge transfer process from Eu³⁺ to Tb³⁺, whereas the latter is attributed to the energy transfer process from Eu²⁺ to Tb³⁺. Tunable white-light emission resulted from the system of SCS:ETE as a result of the competition between these two processes when the Tb³⁺ concentration varies. It was found that the nominal composition Sr_1.5Ca_0.5SiO₄:1.0%Eu³⁺, 0.07%Tb³⁺ is the optimal composition for single-phased white-light phosphor. The CIE chromaticity calculation demonstrated its potential as white LED-based near-UV chip.     

Energy transfer between activators at different crystallographic sites in Sr3SiO5:Eu

A yellow phosphor, Sr₃SiO₅:Eu²⁺, was synthesized by a high temperature solid-state method. Sr₃SiO₅:Eu²⁺ exhibits a single yellow emission under the blue radiation excitation. However, Sr₃SiO₅:Eu²⁺ shows a two-peak emission under the ultraviolet radiation excitation when Eu²⁺ doping content is less than 0.01 mol. Moreover, the blue emission disappears and the yellow emission reaches the peak value when Eu²⁺ doping content is 0.01 mol. Namely, the energy transfer takes place between the Eu²⁺ activators, which is located at two different crystallographic sites in the Sr₃SiO₅. And the energy transfer mechanism is the dipole-dipole interaction.     

Photoluminescence investigations of Zn2SiO4 co-doped with Eu and Tb ions

Zinc silicate phosphors co-doped with Eu³⁺ ions and also with both Eu³⁺ and Tb³⁺ ions were prepared by high temperature solid state reaction in air or reducing atmosphere. The luminescence characteristics of the prepared phosphors were investigated. While in the samples prepared in air, Eu³⁺ emission was found to be dominant over Tb³⁺ emission, in the samples prepared in reducing atmosphere, intense Eu²⁺ emission at 448 nm was found to be predominant over narrow Tb³⁺ emission. Luminescence studies showed that Eu³⁺ ions occupy asymmetric sites in Zn₂SiO₄ lattice. The intense f-f absorption peak of Eu³⁺ at 395 nm observed in these phosphors suggests their potential as red emitting phosphors for near ultra-violet light emitting diodes.     

A potential red-emitting phosphor CaSrAl2SiO7:Eu for near-ultraviolet light-emitting diodes

A novel red-emitting phosphor CaSrAl₂SiO₇:Eu³⁺ was firstly synthesized through the high temperature solid state reaction at 1300 °C. The structure, diffuse reflection spectra, photoluminescence spectra, color-coordinate parameters and quantum efficiencies (QE) of phosphors were investigated. The obtained CaSrAl₂SiO₇:Eu³⁺ phosphors have the same structure with that of the Ca₂Al₂SiO₇ and Sr₂Al₂SiO₇ phosphor, which have the melilite structure. Optical properties were studied as a function of Eu³⁺ concentration x, when x>0.14, the intensity of absorption of the f–f transitions of Eu³⁺ at 393 nm is stronger than that of the broad charge transfer transition band (CTB) around 254 nm, and which matches well with the output lights of NUV–LEDs, whereas, the concentration of Eu³⁺x≤0.14, the absorption of 393 nm is weaker than that of CTB. The underlying reason of Eu³⁺ concentration on their luminescent properties was investigated and discussed in detail. As a result, comparing with the commercial red phosphor Y₂O₂S:Eu³⁺, the CaSrAl₂SiO₇:xEu³⁺ (x>0.14) phosphor exhibited excellent color purity and much higher brightness and could be considered as promising red phosphors for NUV–LEDs.