掺Tb-硅基发光材料制备过程中结构及发光性能

采用溶胶 凝胶技术,制备了不同退火温度下掺Tb3＋的SiO2玻璃,掺Tb3＋的凝胶玻璃在448,544,585,620 nm显示Tb3＋的5D4 7FJ(J=3,4,5,6)的特征发光光谱.通过不同退火温度下样品的激发光谱、发射光谱、红外光谱、远红外光谱及差热 热重谱研究了掺Tb3＋的硅基材料由凝胶向玻璃转变过程中的结构变化及对Tb3＋发光性能的影响.结果显示,在50～100 ℃退火温度下,凝胶大部分吸附水分子被除去,在150～500 ℃退火温度区,是凝胶向玻璃转变的主要结构变化区,并且其发光强度也明显增加,到800 ℃时趋于稳定.这些现象得出一个结论,Tb3＋的发光跃迁被O－H基强烈猝灭而随退火温度的升高而加强.     

溶胶-凝胶法制备掺Eu3+的SiO2玻璃的结构及发光性

利用溶胶-凝胶技术制备了掺不同量Eu3+和不同退火温度下的SiO2凝胶和玻璃,通过在不同退火温度下样品的激发光谱、发射光谱、红外光谱和差热-热重曲线,研究了掺Eu3+的SiO2玻璃材料的结构和发光性能。结果显示当Eu3+的掺杂量大于1.86%（质量分数）,Eu3+的发光强度趋于稳定,当样品的退火温度大于300℃时,SiO2凝胶玻璃中吸附的水已基本除净,此时显示出Eu3+的特征发射光谱,谱带位置分别是614,596,588,577nm,分别归属于5D0-7F2,5D0-7F1,5D0-7F0跃迁,对应的激发光谱显示6个峰,位置分别是318,362,380,393,412,462nm,说明300～500℃是凝胶向玻璃转变的关键温度,而水对Eu3+的发光有强烈的淬灭作用。     

溶胶—凝胶法制备掺Eu^3＋的SiO2玻璃的结构及发光性能

利用溶胶－凝胶技术制备了掺不同量Eu^3 和不同退火温度下的SiO2凝胶和玻璃,通过在不同退火温度下样品的激光发谱,发射光谱,红外光谱和差热－热重曲线,研究了掺Eu3 的SiO2玻璃材料的结构和发光性能,结果显示,当Eu3 的掺杂量大于1．86％（质量分数）,Eu^3 的发光强度趋于稳定,当样品的退火温度大于300度时,SiO2凝胶玻璃中吸附的水已基本除净,此时显示出Eu^3 的特征发射光谱,谱带位置分别是614,596,577nm,分别归属于^5Do-7F2,5D0-7F1,^5D0-^7F0跃迁,对应的激光发光谱显示6个峰,位置分别是318,362,380,393,412,462nm,说明300－500度是凝胶向玻璃转变的关键温度,而水对Eu^3 的发光有强烈的淬灭作用。     

LiGdSiO4：Eu^3＋,Bi^3＋的低温合成及其发光行为的研究

在实验室中.采用溶胶一凝胶法,在比较低的温度下。合成出Li Gd_(0.958)SiO_4:0.035Eu~(3+),0.007Bi~(3+)发光体。利用红外光谱、X射线粉末衍射谱、热重及差热分析、激发光谱和发光光谱,研究了由凝胶至发光晶体的转变过程,讨论了Eu~(3+)、Bi~(3+)在稀土硅酸盐中的发光行为。     

掺Eu的SiO2-B2O3体系和SiO2-B2O3-Na2O体系的结构及Eu3+的发光性质

采用溶胶-凝胶技术制备了掺Eu3+的以SiO2-B2O3和SiO2-B2O3-Na2O为基质的玻璃态发光材料. 通过激发光谱、发射光谱研究了Eu3+的发光性质, 通过红外光谱、 TEM 、 XRT进一步研究了基质结构变化对发光性能的影响. 结果显示 材料经 600 ℃退火处理后, 结构已十分稳定. 在588 nm和613 nm处显示弱的Eu3+的特征发射光谱, 对应于Eu3+的5D0-7Fj(j=1,2)跃迁. 以SiO2-B2O3为基质的玻璃材料的红外光谱显示形成了Si-O-B键. 该结构对Eu3+的发光有严重的淬灭作用, 使Eu3+的发光强度大大减弱. 以SiO2-B2O3-Na2O为基质的玻璃材料显示Eu3+的发光增强, 红外光谱显示不存在Si-O-B键的振动吸收. 可能是Na取代B的位置, 形成了Si-O-Na键. 此结构对Eu3+的发光有一定增加作用.     

Tb掺杂SiO2-B2O3-NaF玻璃的制备及发光性质

使用正硅酸乙酯、硼酸和氟化钠为前驱体,0.10 mol•L-1TbCl3溶液为掺杂剂,通过溶胶-凝胶方法制备了Tb3＋掺杂的SiO2-B2O3-NaF玻璃,研究了Tb3＋在SiO2-B2O3-NaF体系中的发光性质,结果显示发光体能产生强的绿色发光(544 nm),归属于Tb3＋的5D4—7F5电子跃迁.Tb3＋含量不同时,除发光强度不同外,其发射光谱基本相同,并且在低掺杂Tb3＋样品和低退火温度样品中检测到了来自5D3跃迁产生的峰,其跃迁随Tb3＋掺杂浓度的增加和退火温度的升高而发生猝灭,这种现象归因于5D3－5D47F6—7F0和/或5D3—7F07F6—5D4跃迁中发生了交叉弛豫现象.Tb3＋在SiO2-B2O3-NaF玻璃中的激发光谱由一个宽峰和一系列窄峰组成,宽峰最大波长位于230 nm,对应于Tb3＋的4f 8—4f 75d 1跃迁,一系列窄峰位于300～380 nm处,归属于4f 8跃迁,所有发光材料的XRD和TEM测试显示材料是非晶态的.     

硼离子对铕掺杂SiO2干凝胶发光性能的影响

采用溶胶-凝胶法制备了Al单掺和B，Al共掺的Eu掺杂SiO2干凝胶。利用荧光光谱、IR，XRD，DSC，TG／DTG等技术研究了硼离子、退火温度对样品发光性质的影响。经500℃以上退火处理用248nm激发的样品，产生Eu^3＋离子^5D0→^7FJ的特征发射，^5D0→^7F1的跃迁分裂为两个峰。比较615nm处的发光强度，掺硼酸样品的发光强度是不加硼酸发光强度的3．3倍。这是因为B离子的加入，在材料中形成了Si—O—B键，破坏了网络的对称性，加强了Eu^3＋的红光发射。当退火温度上升到850℃用350nm激发时，样品有很强的Eu^2＋蓝光发射。Al单掺的发射中心在437nm处，发射半峰宽约为70nm，而B，Al共掺样品的发光中心蓝移到425nm处，单掺样品的蓝光强度几乎是共掺样品强度的2倍。这是由于硼酸的加入改变了基质的网络结构，从而导致单掺和共掺样品发射峰位和强度的改变。     

溶胶-凝胶法制备掺Sm3+的SiO2玻璃的结构及发光性能

利用溶胶-凝胶技术制备了掺不同量Sm3+和不同退火温度下的SiO2凝胶和玻璃,通过三维荧光光谱、激发光谱、发射光谱的测试,确定了Sm3+在SiO2凝胶玻璃中的最佳激发波长为360 nm,最强发射波长为610 nm,激发光谱的峰位置在360、393、464 nm处,发射光谱的峰位置在578、591、595、610、732nm处,分别归属于4G5/2-6H5/2、4G5/2-6H7/2、4G5/2-6H11/2跃迁,并证明当掺杂量达到1.15%时,Sm3+的发光最强,当Sm3+的掺杂量超过1.15%时,发生浓度猝灭效应.     

增强掺Tb凝胶玻璃荧光性能的有机螯合体的选择

采用原位合成技术, 用溶胶凝胶法制备了稀土离子(Tb^3＋), β-二酮及协同体共掺的二氧化硅玻璃, 测量了它们发射光谱和红外光谱, 并进行了XRD, SEM和TG-DSC测试. 探讨各不同成分原位合成稀土有机配合物在二氧化硅玻璃中的发光性能及热处理温度对发光性能的影响. 结果表明, 在凝胶玻璃中掺入能级较匹配的β-二酮, 可以使稀土离子的荧光增强; 合适的协同体的引用也能使稀土离子的荧光增强. 这些结果为今后制备荧光较强的含Tb离子的SiO₂凝胶玻璃提供了一定的依据.     

Tb3+在燃烧法制备的CaLaAl3O7粉体中的发光性能

采用柠檬酸燃烧法制备了稀土TB3 掺杂的CaLa1-xAl3O7:xTb3 发光材料的前驱粉末,在低于700℃退火处理时,得到非晶态样品,而高于800℃退火处理后为纯相的CaLa1-xAl3O7:xTb3 粉末样品.通过三维荧光光谱、激发光谱和发射光谱研究了Tb3 在CaLaAl3O7基质中的发光性能及Tb3 掺杂量、退火温度和柠檬酸与金属离子的配比等对发光强度的影响.结果显示.非晶态和晶态CaLa1-xAl3O7:xTb3 品都可发光,在240 nm波长光的激发下,CaLaAl3O7:Tb3 粉体产生Tb3 的特征发射峰,归属于5D4-7FJ(J=6,5,4,3)跃迁,主发射峰位置均在543 nm处(5D4-7F5跃迁),随着粉末逐渐成相5D4-7F5跃迁明显增强.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.