In/HZSM-5催化剂上CH4选择还原NO机理研究

考察了CH⁴+O₂,NO+CH₄(+O₂)与NO₂+CH₄(+O₂)反应体系中CH₄的转化活性.结果表明,浸渍法制备的In/HZSM₅催化剂上CH₄选择还原NO过程中,NO₂的形成起到了活化甲烷的作用.根据NO和NO₂在In/HZSM₅与HZSM₅样品上的TPD及IR研究结果,认为在载体HZSM₅的酸性位及In/HZSM₅催化剂的活性中心In位上均可形成NO₂,NO₂与CH₄的反应在In位上进行.     

铈铁锆三元复合氧化物上碳烟的催化燃烧

采用水热法制备了纯CeO₂、Fe₂O₃和系列Ce₀.5Fe₀.5-xZr_{xO2复合氧化物催化剂,采用XRD、Raman、H2-TPR和BET等方法对其进行了表征,并利用程序升温氧化反应(TPO)技术研究了其碳烟燃烧催化性能。结果表明,Zr⁴+完全进入CeO2晶格中形成了固溶体,而Fe³+较难进入CeO2晶格中,部分Fe2O3分散在固溶体表面。固溶体形成产生的氧空位和表面高度分散的氧化铁协同作用是铈铁锆三元复合氧化物具有较高碳烟燃烧催化性能的关键。同时,与单纯的铈铁二元复合氧化物相比,Zr⁴+的掺杂明显提高了催化剂的抗老化能力,使Ce0.5Fe0.5-xZrxO2复合氧化物显示出更好的应用前景。在系列样品中,Ce0.5Fe0.30Zr0.20O2样品由于形成了最多的固溶体并具有良好分散性的表面Fe2O3,显示出最好的催化活性和稳定性。其催化碳烟的起燃温度(ti)和峰顶温度(tp)分别为251℃和310℃,长时间高温老化后其ti和tp仍较低,分别为273℃和361℃。}     

多孔离子交换树脂内Eu3+离子的分步扩散

用同位素交换法研究了Eu³⁺离子在D72和D751树脂内的扩散过程.应用分步孔道扩散方程将粒内有效扩散系数D_e分解为孔道扩散系数D_p和固相扩散系数D_g,表明该方程可用于描述多孔树脂内的动力学过程.实验表明,D_e、D_p、D_g均随反应温度的升高而增大.计算了实验条件下的Eu³⁺的自扩散活化能;D72树脂的D_p和D_g对温度的响应比D751树脂大,其D_e、D_p、D_g值亦均大于D751树脂;Eu³⁺在溶液中的自扩散系数D_s＞D_p,说明离子在树脂孔道内的自扩散不能完全等同于其在溶液中的自扩散.     

不同整比性VO2纳米粉体的合成

以V₂O₅,HCl,N₂H₄·2HCl和NH₄HCO₃为原料合成了紫红色多晶(NH₄)₅[(VO)₆(CO₃)₄(OH)₉]·10H₂O(I),产率80％～95％.在N₂气流中对前体I进行了TG/DTG和DTA热分析.研究了前体I在N₂-空气气流中热解时氧分压(po₂)和反应温度对产物VO₂整比性的影响.结果表明,在500℃条件下,VO_x中的x值与po₂呈正比关系,在po₂=30.3Pa条件下,在450～520℃区间,产物为缺氧VO₂;在t<450℃和t>520℃时,产物为富氧VO₂.在合适的条件下,成功地合成了从VO_1.927到VO_2.080之间不同整比性的VO₂粉体.产物组成均匀,其XRD谱未观察到非VO₂的杂质峰.VO₂粉体颗粒的平均粒径为20nm,粒度分布均匀并呈球形.     

臭氧氧化结合湿法喷淋对玻璃窑炉烟气同时脱硫脱硝实验研究

采用臭氧氧化结合湿法喷淋对模拟玻璃窑炉烟气开展了同时脱硫脱硝实验研究.采用不同溶液(NaOH、Na₂S)进行了喷淋实验.结果表明,保证溶液pH值在10以上,NaOH浓度对NO_x脱除效率无影响,SO₂的存在促进了NO_x吸收.当O₃/NO物质的量比为1.6、溶液NaOH浓度为0.5%时,NO_x脱除效率可达70%,SO₂脱除效率在99%以上.往喷淋液中添加Na₂S,NO_x脱除效率随Na₂S浓度增加而提高,SO₂的存在对NO_x脱除效率无影响.当O₃/NO物质的量比为1.2、溶液中NaOH浓度为0.5%、添加剂Na₂S浓度为0.6%时,NO_x脱除效率可达70%,SO₂脱除效率在95%以上.60 min长时间运行实验证明,模拟烟气中的NO_x经碱液和添加剂吸收后主要以NO^-₂的形式存在于喷淋液中,且NO_x脱除效率不随溶液pH值的变化而变化.     

β-Bi2O3修饰Bi2WO6光催化降解苯酚及其可能机理

采用简单混合法制备了一系列Bi₂O₃/Bi₂WO₆复合光催化剂. 在紫外光降解水中苯酚的过程中, Bi₂O₃/Bi₂WO₆的光催化活性随Bi₂O₃含量的增加呈现先增大后减小的趋势. 当Bi₂O₃最佳负载量等于12.5% (质量分数, w)时, 该复合光催化剂的活性大约是单一Bi₂WO₆的4 倍. 固体样品表征表明, Bi₂O₃主要以β-Bi₂O₃存在, 复合光催化剂是Bi₂O₃和Bi₂WO₆的简单混合物. 此外, 在电催化氧化水的过程中, β-Bi₂O₃/Bi₂WO₆薄膜电极的光电流远大于β-Bi₂O₃和Bi₂WO₆薄膜电极的光电流之和. Bi₂O₃对Bi₂WO₆光催化的促进作用是由于前者接受后者的光生空穴, 提高Bi₂WO₆光生载流子的分离效率, 从而加快了O₂的还原和苯酚的降解.     

CeO2/TiO2复合纳米纤维的制备及光催化性能研究

采用静电纺丝技术和水热合成法制备了CeO₂/TiO₂复合纳米纤维. 利用X射线衍射(XRD)、拉曼光谱(Raman)、扫描电镜(SEM)、透射电镜(TEM)和比表面积测定(BET)等分析测试手段对样品的形貌及结构进行了表征, 并以罗丹明B的脱色降解为模式反应, 考察了样品的光催化性能. 结果表明: CeO₂纳米粒子均匀地生长在TiO₂纳米纤维表面, 形成了异质结构的CeO₂/TiO₂复合纳米纤维光催化材料. 通过改变碱源, 可以得到不同形貌的CeO₂. CeO₂的存在增加了TiO₂纳米纤维的比表面积, 有效地实现TiO₂光生电子和空穴的分离, 增强了体系的量子效率, 与纯TiO₂纳米纤维相比光催化活性明显提高. 初步探讨了异质结的形成机理.     

C59(C6H4OCH3)N的结构、光谱和二阶非线性光学性质的理论研究

用INDO系列方法对由(C₅₉N)₂和苯甲醚合成的衍生物C₅₉(C₆H₄OCH₃)N进行了理论研究,得到了分子的稳定构型.结果表明,C₅₉(C₆H₄OCH₃)N具有C_s对称性.以优化构型为基础讨论了分子的UV-Vis光谱、NMR谱线数,结果与实验符合得很好.本文还计算了C₅₉(C₆H₄OCH₃)N的二阶非线性光学系数β_μ,结果表明这种物质具有较大的二阶非线性光学系数.     

互穿结构及混合配体对金属-有机骨架材料分离性能的影响

在以前的工作中, 我们利用蒙特卡洛和分子动力学模拟计算了具有互穿性结构及混合配体的金属-有机骨架材料(metal-organic frameworks, MOFs)分离CH₄/H₂的吸附选择性及扩散选择性. 研究了材料的互穿结构及混合配体对材料用于分离CH₄/H₂性能的影响. 在本工作中, 我们将以前的工作进行了扩展, 详细研究了材料的互穿结构及混合配体对材料用于分离CO₂/CH₄, CO₂/N₂和CO₂/H₂等含有CO₂的气体混合物性能的影响. 此外, 为了进一步阐明材料的结构对于其分离性能的影响, 我们亦研究了材料用于分离CH₄/H₂及CH₄/N₂. 从我们的结果可以看出, 相比无互穿结构的MOFs材料, 具有互穿结构的MOFs材料对所研究的所有混合气体的渗透选择性明显提高. 这是因为具有互穿结构的MOFs材料对混合气体的吸附选择性明显高于无互穿结构的MOFs材料. 结果表明, 如果将材料作为膜用于气体混合物分离, 使材料产生互穿结构是提高材料分离性能的一个很好的策略.     

微波辅助合成具有优异电化学性能的rGO/CeO2超级电容器电极材料

CeO₂具有良好的赝电容, 但有关碳/CeO₂复合材料的电化学性能有待改善. 本工作采用简单的微波辅助合成法, 将氧化石墨烯与Ce(NO₃)₃混合发生氧化还原反应, 获得还原氧化石墨烯(rGO)/CeO₂复合材料. 通过形貌观察, CeO₂以颗粒形式均匀分布在褶皱的rGO上, 且沿着rGO表面仿形生长; 纳米级CeO₂颗粒之间存在微小间隙. N₂吸/脱附测试结果表明, rGO/CeO₂具有大的比表面积和介孔孔径, 有益于与电解液充分接触. 通过电化学测试, rGO/CeO₂的比电容高达468 F•g^-1, 经过10000次充放电循环, 电容保持率高达107.3%. 优异的循环稳定性归因于大表面积的rGO与均匀薄层的CeO₂良好的协同效应减少了离子传输的阻力以及CeO₂颗粒之间微小的间隙, 缓解了Ce⁴⁺还原为Ce³⁺过程中发生的晶格膨胀. 将rGO/CeO₂组装成对称型超级电容器rGO/CeO₂||rGO/CeO₂获得的能量密度达18.16 Wh•kg^-1. rGO/CeO₂作为超级电容器电极材料具有广阔前景.     

A new method for the determination of mobile phase volume in normal and reversed-phase liquid chromatography

Summary A new method for the determination of the mobile phase volume (V _m) in liquid chromatography is presented based on the model regarding the retention of ionic solutes in the presence of eluent electrolytes. TheV _m value can be determined by measuring the retention volumes of two ions that have the same charge in two eluent electrolyte systems. Compared with the methods using isotopically labelled eluent components or inorganic salts asV _m markers, the method presented is proved to give more reasonableV _m values for both normal and reversed-phase liquid chromatography. As well as in binary mixed solvent systems, theV _m values in single solvent systems can be determined by this method.     

Evaluation of Dead Time Calculation in Reversed-Phase Liquid Chromatography Using a Multiparametric Mathematical Method

In reversed phase liquid chromatography (RP-HPLC), the validity of a multiparametric non-linear least-squares regression iterative method for the determination of the column dead time t_M and the regression parameter (slope b), based on the use of alkan-2-ones, alkyl aryl ketones, and 1-nitroalkanes has been evaluated. The determination of t_M and b has been extensively studied for two mobile phase systems acetonitrile-water and methanol-water on seven octadecyl-C₁₈ and one octyl C₈ analytical columns. The calculated t_M and b values were compared with those obtained by Guardino's and Grobler's methods. The influence exerted thereon by the nature of the homologous series, the mobile phase composition, and the packing materials were investigated.     

Photopyroelectric method

High resolution measurements have been performed with a photopyroelectric (PPE) technique to study the static and dynamic thermal parameters behaviour in the critical region of different liquid and solid samples. In particular the specific heat (c), the thermal diffusivity (D) and the thermal conductivity (k) have been simultaneously determined in the critical region around the antiferromagnetic/paramagnetic (AP) phase transition occurring in FeF₂ and around the Smectic-A/Nematic (AN) phase transition occurring in the 8S5 liquid crystal.The high resolution of the measuring technique has allowed the determination of thec andD critical exponents and amplitude ratio of their critical terms.     

Techniques used to study the chemistry of gas phase elemental clusters

Recent studies of the chemistry of elemental clusters (such as C _n , Si _n , and Fe _n ) in the gas phase have revealed a number of fascinating results. This review article discusses and compares the various techniques that have been used to investigate the chemical properties of gas phase elemental clusters. Examples are provided of the often complimentary information that can be obtained from the different methods.     

Water effect on the gelation behavior of polyacrylonitrile/dimethyl sulfoxide solution

The gelation behavior of polyacrylonitrile (PAN)/dimethyl sulfoxide (DMSO) solution containing different amounts of water has been investigated using various methods. The ternary phase diagram of PAN/DMSO/water system indicated that water enhanced the temperature at which phase separation of PAN/DMSO solution occurred. Intrinsic viscosities [η] of dilute PAN/DMSO solution and PAN/DMSO/water solution at varied temperatures were measured to examine the influence of water on the phase behavior of PAN/DMSO solution. The presence of water in the solution gave rise to elevated critical temperature T_c. The gelation temperature T_g obtained by measuring the loss tangent tan δ at different oscillation frequencies in a cooling process was found to increase with increased water content in the solution. The critical relaxation exponent n value, however, changed little with varied concentration. During the aging process, the gelation rate of PAN/DMSO solution increases with the water level. The n values of the PAN/DMSO solutions with 2 wt% and 4 wt% water were a little larger than that of the solution without water, which may be explained by the turbid gel resulted from phase separation. The n values obtained in the aging process were larger than those obtained in the cooling process for the same three solutions, ascribed to the weaker gel with less cross-linking points formed in long time. Water led to the formation of denser gel structure. The coarser gel surface can also be attributed to the phase separation promoted by water.     

Investigating polymer blend miscibility with forward recoil spectrometry

We tested forward recoil spectrometry (FRES) as a method to determine miscibility by measuring coexistence compositions in binary polymer blends. In this study, equilibrium phase compositions were determined for a compositionally symmetric poly(styrene‐ran‐methyl methacrylate) random copolymer (S_0.49‐r‐MMA) and two homopolymers, deuterated polystyrene (dPS) and deuterated poly(methyl methacrylate) (dPMMA). Sample preparation, film dewetting, and beam damage were addressed, and the results for these polymer blends were in good agreement with those obtained through other experimental techniques. Deuteration had a strong effect on the miscibility of the dPS/S_0.49‐r‐MMA and dPMMA/S_0.49‐r‐MMA blends, to the extent that the asymmetric miscibility observed separately for the PS/S_0.49‐r‐MMA and PMMA/S_0.49‐r‐MMA blends was not found. Although this deuteration effect may limit the applicability of FRES for some polymer systems, the accuracy with which phase compositions can be determined with FRES makes it an attractive alternative to other less quantitative methods for investigating blend miscibility. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1547–1552, 2000     

层状钙钛矿化合物 (n-CnH2n+1NH3)2ZnCl4非等温固-固相变动力学的确定

确定了具有层状钙钛矿结构,脂肪链C原子数从12到18四氯合锌酸二烷基铵(C_nH_2n+1NH₃)₂ZnCl₄系列化合物的非等温固-固相变动力学。采用Kissinger和Ozawa两种动力学模型,对不同温度下测定的每个样品DSC热分析曲线进行数据处理,计算固-固相变过程的活化能E_a。实验结果表明,随着C原子数的增加,脂肪链的有序度和刚度降低,导致固-固相变活化能E_a随C原子数的增大而降低。两种模型方法的计算活化能E_a的结果相一致。并且各个化合物的固-固相变反应级数不随升温速率和烷基链长变化而变化,总保持为1。     

Unusual asymmetry in halobenzenes,a solid-state,gas-phase and theoretical investigation

The molecular structures of 1-Br-4-F-C₆H₄ and 1-Cl-4-F-C₆H₄ have been studied in the gas phase using gas electron diffraction (GED) and ab initio methods. The structure of 1-Cl,4-F-C₆H₄ in the crystalline phase has also been studied, but whilst the gaseous structures were found to possess C _2v symmetry, the solid-state structure was found to be quite distorted, with three molecules in the asymmetric unit. These fragments only possess C _s symmetry in the plane of the molecules, as opposed to the C _2v symmetry observed in the gas phase. The bonding motifs within the solid-state structure are very unusual and unexpected, with quite different C–F bond lengths for the three moieties, and are a result of weak hydrogen-halogen interactions within the structure.     

Methods for evaluating the association of some extractants in low polarity solvents

On the basis of vapor phase osmometry data the activity coefficients of TBP, D2EHPA and some tertiary amines have been calculated. The applicability of various methods for the evaluation of association constantsK _i in the extraction systems is presented.     

Plastic deformation of poly(tetramethylene oxide). II. Molecular orientation as measured by x-ray diffraction and NMR measurements

The orientation of the crystalline and amorphous phases in uniaxially drawn samples of polytetramethylene oxide has been studied by x-ray and NMR methods. Pole figure measurements give the orientation of the crystalline phase. Its dependence on the draw ratio does not obey the pseudoaffine model. The crystalline fraction is derived from NMR measurements at temperatures between T_g and T_m, where the free induction decay (FID) of the unoriented sample can be analyzed in terms of a rigid (crystalline), a constrained, and an amorphous phase. Low temperature (T < T_g) measurements of the NMR second-moment anisotropy in protonated and deuterated samples give a mean orientation of the chains higher than that corresponding to the crystalline phase. The lack of anisotropy in the tail of the FID at temperatures between T_g and T_m indicates no appreciable anisotropy in the truly amorphous interlamellar phase. From this and from the ratio of the P₄/P₂ orientations, factors which obey the “most probable distribution,” it is concluded that the amorphous orientation is due to the layer of constrained chains at the surface of the lamellae.