Thermal studies of hypervalent iodine reagents

The use of unconventional synthesis methods in the formation of CaO·2Al₂O₃ (CA₂) is justified because it reduces the formation temperature of the compound. CA₂ is formed by classical method at temperatures above 1,400 °C. The polymeric precursor method allows a significant temperature decrease in CA₂ synthesis reaching temperatures of 1,000 °C. This paper deals with CA₂ synthesis by “citrate” method which is often presented as Pechini method, starting from a mixture of citric acid, ethylene glycol and calcium, and aluminum nitrates. A method based on the formation of a polymeric precursor was also used, starting from a mixture of acrylic acid and nitrates of calcium and aluminum. The results showed a net difference in favor of samples obtained from acrylic acid, which by annealing at 800 °C for 1 h, contain pure CA₂. The samples obtained from citric acid, after annealing at 800 °C are amorphous. After annealing at 900 °C in all samples CA₂ is single phase.     

Physical and electrochemical properties of (La0.3Sr0.7)0.93TiO3–δ synthesized by Pechini method as an anode material for solid oxide fuel cells

The lanthanum strontium titanate (LST) has to be calcined at significantly high temperature (above 1,300 °C) to obtain its pure perovskite structure when synthesized by conventional solid-state method, which is main reason for reducing active surface area. In this study, A-site deficient (La_0.3Sr_0.7)_0.93TiO₃ was synthesized by Pechini method. Although the prepared powders were calcined at 600 °C, the pure perovskite structure can be obtained without any secondary phase such as TiO₂. Moreover, the porosity and surface area are 6 times and one order of magnitude higher in the LST powders synthesized by Pechini method than in the powders synthesized by solid-state method. Based on these results, the LST electrode (Pechini) leads to two times lower electrode resistance than the LST electrode (solid-state). Thus, the LST powders synthesized by Pechini can contributes to saving the energy needed for calcination process as well as increasing the porosity and active surface area, enhancing physical and electrochemical properties in SOFC anode.     

The thermal behavior of some polymeric precursors used in CaAl12O19 synthesis

CaAl₁₂O₁₉ was synthesised using three different precursors: (a) a polyesteric type precursor resulted from the traditional Pechini method; (b) a polyesteric type precursor resulted from the reaction between citric acid and calcium and aluminum nitrates; and (c) a polymeric type precursor resulted from the reaction between acrylic acid and calcium an aluminum nitrates. The thermal behavior of the three precursors used in the CaAl₁₂O₁₉ synthesis was monitored to underline the thermal effects associated to the CaAl₁₂O₁₉ formation. Thermal analyses performed on precursors do not reveal clear differences regarding the thermal effects assigned to calcium aluminates formation, at temperatures over 800?°C. In contrast, thermal analysis of samples pre-fired at 200?°C, and especially at 600?°C, show clear differences between samples obtained in different ways. It is noted that in samples obtained from acrylic acid and nitrates, and citric acid and nitrates, CA₆ is practically single phase after calcination at 1,200?°C. However, in the sample obtained from citric acid, ethylene glycol, and nitrates, calcined at 1,200?°C, CA₆ is present along with CA₂ and ??-Al₂O₃.     

Crystallization study of SrSnO3:Fe

Alkaline earth stannates have recently become important materials in ceramic technology due to its application as humidity sensor. In this work, alkaline earth stannates doped with Fe³⁺ were synthesized by the polymeric precursor method, with calcination at 300 °C/7 h and between 400 and 1100 °C/4 h. The powder precursors were characterized by TG/DTA after partial elimination of carbon. Characterization after the second calcination step was done by X-ray diffraction, infrared spectroscopy, and UV?Cvis spectroscopy. Results confirmed the formation of the SrSnO₃:Fe with orthorhombic perovskite structure, besides SrCO₃ as secondary phase. Crystallization occurred at 600 °C, being much lower than the crystallization temperature of perovskites synthesized by solid state reaction. The analysis of TG curves indicated that the phase crystallization was preceded by two thermal decomposition steps. Carbonate elimination occurred at two different temperatures, around 800 °C and above 1000 °C.     

Influences of synthesis route and preparation process on the electrochemical properties of Fe-doped strontium cobaltite

SrCo_0.8Fe_0.2O_3-δ (SCF), as a promising cathode material for intermediate temperature solid oxide fuel cells, possesses a high catalytic activity for the reduction of O₂ to 2O²⁻. The SCF powder was successfully synthesized by the solid state reaction method and Pechini method and characterized using XRD, particle analysis, and electrochemical performance measurements. Smaller-particle-size SCF materials (SCF-P) with single phase are obtained at lower synthesis temperature by the Pechini method and possess better electrochemical performance as compared with those prepared by the solid state reaction method. The reason is that the Pechini method involves the mixing of elements at atomic level, so pure SCF phase formation can be accelerated and showed high electrocatalytic activity. The preparation procedure of SCF cathode was firstly investigated using electrochemical impedance spectroscopy. Results show that the total polarization resistance and the low-frequency resistance decrease gradually with the reduction of the calcination temperature for the SCF cathodes. The SCF-P cathode sintered at 1,000 °C possesses the highest porosity and the best electrochemical performance. It is the result of a comprehensive function of three-phase boundary length, porosity of cathode, and the adhesion between cathode and electrolyte. The charge-transfer process, together with the adsorption, dissociation, and diffusion of oxygen, has a strong influence on the whole reaction process of the cathode. The influence of binder amounts on the performance of the SCF-P cathodes was also studied.     

Heterogeneous Fenton reactants: a study of the behavior of iron oxide nanoparticles obtained by the polymeric precursor method

Nanoparticles composed of iron oxides and iron salts were obtained from polymeric resins produced by polymerizing Fe²⁺-citrate and Fe³⁺-citrate complexes with ethylene glycol. The citric acid:Fe molar ratio was varied to obtain different synthesis conditions. The materials were treated at 450 °C for 2 h to obtain nanoparticles, which were characterized by XRD, Mössbauer spectroscopy, FEG, CHNS, atomic absorption and surface area through N₂ physisorption. Rhodamine B photo degradation in the presence of these nanoparticles and hydrogen peroxide was carried out to analyze the possible behavior of nanoparticles as heterogeneous Fenton reactants. UV–visible spectroscopy revealed that the catalytic activity in the presence of nanoparticles obtained with a citric acid:Fe molar ratio of 12:1 was the condition that provided the best results in this work.     

Thermal and structural investigation of SnO<Subscript>2</Subscript>/Sb<Subscript>2</Subscript>O<Subscript>3</Subscript> obtained by the polymeric precursor method

SnO₂-based materials are used as sensors, catalysts and in electro–optical devices. This work aims to synthesize and characterize the SnO₂/Sb₂O₃-based inorganic pigments, obtained by the polymeric precursor method, also known as Pechini method (based on the metallic citrate polymerization by means of ethylene glycol). The precursors were characterized by thermogravimetry (TG) and differential thermal analysis (DTA). After characterization, the precursors were heat-treated at different temperatures and characterized by X-ray diffraction. According to the TG/DTA curves basically two-step mass loss process was observed: the first one is related to the dehydration of the system; and the second one is representative to the combustion of the organic matter. Increase of the heat treatment temperature from 500 to 600°C and 700°C resulted higher crystallinity of the formed product.     

Synthesis of Cu2Mo6S8 powders and thin films from intermediate oxides prepared by polymeric precursor method

Powders and thin films of the copper molybdenum sulfide Cu₂Mo₆S₈ were synthesized from intermediate oxides prepared by polymeric precursor method based on Pechini process. In the case of the thin films, deposition was performed onto R-plane sapphire single crystal by spin coating. The influence of temperature and duration of the 3 step heat treatment cycle (calcination, sulfurization and reduction) were investigated to optimize the synthesis conditions. The first step of calcination under air atmosphere performed for 3 h at 450 °C and 400 °C is suitable to obtain the intermediate oxides powders and thin films, respectively. The sulfurization treatment at 600 °C for 2 h under H₂S/H₂ gas flow followed by reduction at 650 °C for 4 h under H₂ gas flow allowed to obtain Cu₂Mo₆S₈ in powder or thin film form. In the last case, a multilayer process led to dense and homogeneous films. Moreover, the insertion and superconducting behaviour of the final powders allowed to validate the Cu₂Mo₆S₈ synthesis by this moderate temperature process.     

Mullite crystallization using fully hydrolyzed silica sol: the gelation temperature influence

Mullite is an aluminosilicate widely used as a structural material for high temperature applications. This paper studies the effect of the gelation temperature on the synthesis of two mullite precursors: polymeric and colloidal silica, using both in fully-hydrolyzed silica sol, derived from sodium silicate. The gels were synthesized using aqueous silicic acid and aluminum nitrate. Ethylene glycol was added into polymeric gels. Two gelation temperatures were used: 80 and 100 °C. In the polymeric precursor, the increasing of the gelation temperature caused an increase in the silica incorporation inside the mullite crystalline lattice at 1,000 °C, and it also generated an increase in the reaction extent at all calcination temperatures. In the colloidal precursors, these effects were more intense than in the polymeric precursors in terms of yield. Colloidal samples calcined at 1,250 °C crystallized cristobalite and alpha alumina in addition to mullite when they were previously gelled at 80 °C. On the other hand, the same sample gelled at 100 °C led to only crystallized mullite. The reaction extent increased by more than 20 % for colloidal samples gelled at 100 °C compared to colloidal samples gelled at 80 °C (calcined at 1,250 °C). This increase was due to the almost total incorporation of alumina and silica in the crystalline lattice of mullite.     

Influence of annealing temperature on the electrochemical and surface properties of the 5-V spinel cathode material LiCr0.2Ni0.4Mn1.4O4 synthesized by a sol–gel technique

LiCr_0.2Ni_0.4Mn_1.4O₄ was synthesized by a sol–gel technique in which tartaric acid was used as oxide precursor. The synthesized powder was annealed at five different temperatures from 600 to 1,000 °C and tested as a 5-V cathode material in Li-ion batteries. The study shows that annealing at higher temperatures resulted in improved electrochemical performance, increased particle size, and a differentiated surface composition. Spinel powders synthesized at 900 °C had initial discharge capacities close to 130 mAh g^?1 at C and C/2 discharge rates. Powders synthesized at 1,000 °C showed capacity retention values higher than 85 % at C/2, C, and 2C rates at 25 °C after 50 cycles. Annealing at 600–800 °C resulted in formation of spinel particles smaller than 200 nm, while almost micron-sized particles were obtained at 900–1,000 °C. Chromium deficiency was detected at the surface of the active materials annealed at low temperatures. The XPS results indicate presence of Cr⁶⁺ impurity when the annealing temperature was not high enough. The study revealed that increased annealing temperature is beneficial for both improved electrochemical performance of LiCr_0.2Ni_0.4Mn_1.4O₄ and for avoiding formation of Cr⁶⁺ impurity on its surface.     

The synthesis of nano-sized undoped,Bi doped and Bi,Cu co-doped SrTiO3 using two sol–gel methods to enhance the photocatalytic performance for the degradation of dibutyl phthalate under visible light

Two sol–gel methods (the citric acid gel and the Pechini methods) were used for the preparation of nano-sized undoped, Bi-doped and Bi, Cu co-doped SrTiO₃ samples to optimize their properties for the photocatalytic degradation of dibutyl phthalate. The perovskite-like phase was detected for the samples prepared by the citric acid gel method after calcination at 800 °C for 3 h, while in the case of the Pechini method; it was detected after calcination at 800 °C for 9 h. The particle size of the samples prepared by the citric acid gel method is greater than that of the samples prepared by the Pechini method. Cu doping in both methods increased the particle size. Cu doping, Bi doping and Bi, Cu co-doping in both methods shifted the absorption edge to the visible light range as well. The band gap of Bi, Cu co-doped SrTiO₃ is smaller than that of Bi doped SrTiO₃, which in turn is smaller than that of undoped SrTiO₃. The highest removal of the total organic carbon (TOC) of DBP was obtained using a Bi, Cu co-doped SrTiO₃ sample prepared by the citric acid gel method. TOC removal of DBP followed pseudo-first order kinetics.     

Environmentally benign sol–gel derived nanocrystalline rod shaped calcium doped cerium phosphate yellow-green pigment

Nanocrystalline rod shaped calcium doped cerium phosphate yellow-green pigment particles having an average length of ~100 nm and aspect ratio 10 even after calcination at 600 °C have been realized through an aqueous sol–gel process. The morphology, particle size and identification of the phase are determined by using different analytical tools such as transmission electron microscopy (TEM), photon correlation spectroscopy (PCS), Fourier-transform IR (FTIR) and X-ray diffraction (XRD). Brunauer–Emmett–Teller (BET) nitrogen adsorption analysis showed the pigment particles are mesoporous texture having specific surface area 42 m² g^?1 and average pore size 153 Å. Thermogravimetric (TG) analysis is used to explain the thermal phase stability of the pigment. UV–Visible spectroscopy and colorimetric analysis are also done. The typical yellow-green color has been obtained even after heating to as low as 600 °C, which is 300 °C lesser than reported. Systematic study on synthesis and effect of temperature on color are presented.     

Influence of pH and microwave calcination on the morphology of KGd(WO<Subscript>4</Subscript>)<Subscript>2</Subscript> particles derived by Pechini Sol–Gel method

KGd(WO₄)₂ (KGW) particles were synthesized at 3.5, 5.5 and 7.5 pH values by Pechini polymeric complex sol–gel method using potassium nitrate, gadolinium nitrate, ammonium paratungstate, citric acid and ethylene glycol as starting materials. Deionized water was used as solvent. Polymeric precursor gel was formed with citric acid as complexing agent and ethylene glycol as binder. Synthesized gel was analyzed by FT-IR spectroscopy. Prepared precursor gels were further annealed using resistive and microwave processes at 550 and 700 °C, respectively. The properties of heat treated samples were characterized by powder XRD, FT-IR, Raman and SEM analysis to understand the crystallinity, organic liberation, tungstate ribbon formation and surface morphology, respectively. The phase formation and different phases of intermediate oxides in pre-fired samples were investigated by powder XRD. Organic liberation in the samples in relation to temperature, and the carbon content in the pre-fired powder was analyzed using FT-IR spectrum. Raman spectrum reveals the formation of tungsten ribbons as well as the quality of the samples. The morphological changes at different synthesis conditions were observed with SEM micrographs.     

Microcalorimetric study of the effect of manganese on the growth and metabolism in a heterogeneously expressing manganese-dependent superoxide dismutase (Mn-SOD) strain

DSC, SEM–EDS, XRD and high-temperature XRD analysis was used to study thermal and crystallization behaviour of yttrium aluminate glasses prepared in the form of microspheres. The glasses YA-E (eutectic composition from the pseudo-binary system Al₂O₃–Y₃Al₅O₁₂) and YA-G (a composition identical to the stoichiometric Y₃Al₅O₁₂ (YAG) phase) were prepared by combination of the Pechini method with flame synthesis. The resulting microspheres were largely amorphous, but contained traces of yttrium–aluminium garnet as the main crystalline phase embedded in the yttrium aluminate glass matrix. Crystallization of the YAG phase was observed as the dominant exothermic process on DSC curves. From the DSC records, the basic thermal characteristics of the matrix glass, i.e. T _g (glass transition temperature), T _x (onset of crystallization peak temperature), T _f (temperature of the inflection point of the crystallization peak) and T _p (maximum of crystallization peak temperature), were determined. HT XRD experiments in the temperature interval 750–1200 °C and isothermal HT XRD experiments at 932, 998 and 1200 °C with 6-h holding time were also performed. Crystallization experiments at lower temperatures 932 °C (YA-E) and 915 °C (YA-G) were conducted to study phase development in a low-temperature region. Crystallization experiments at higher temperatures (1000, 1300 and 1500 °C) with maximum holding time of 6 h were performed to study crystallization of α-Al₂O₃ in the eutectic system. The SEM and SEM–EDS examination of polished cross sections of crystallized microspheres revealed slow volume crystallization of the YAG phase in the AY-E glass. Eventually, polycrystalline microspheres with fine-grained microstructure were prepared after 6-h treatment at 1500 °C.     

Synthesis of nanosized (Li,La){Ti,Nb,Ta}O3 particles using the sol-gel method

Nanoparticles of lithium titanate, niobate, and tantalate with the structure of defect perovskite were synthesized using the Pechini method. The formation of single-phase lithium lanthanum titanate was shown to occur at 700°C. The average particle size was d ～ 15 nm. For niobate and tantalate, the formation of the perovskite phase started at 900°C; the average particle size in this case was 50–100 nm.     

Solid-state synthesis of undoped and Sr-doped K<Subscript>0.5</Subscript>Na<Subscript>0.5</Subscript>NbO<Subscript>3</Subscript>

The solid-state synthesis of undoped K_0.5Na_0.5NbO₃ (KNN) and KNN doped with 1, 2 and 6 mol% Sr, from potassium, sodium and strontium carbonates with niobium pentoxide, was studied using thermal analysis and in situ high-temperature X-ray diffraction (HT-XRD). The thermogravimetry and the differential thermal analyses with evolved-gas analyses showed that the carbonates, which were previously reacted with the moisture in the air to form hydrogen carbonates, partly decomposed when heated to 200 °C. In the temperature interval where the reaction was observed, i.e., between 200 and 750 °C, all the samples exhibited the main mass loss in two steps. The first step starts at around 400 °C and finishes at 540 °C, and the second step has an onset at 540 °C and finishes with the end of the reaction between 630 and 675 °C, depending on the particle size distribution of the Nb₂O₅ precursor. According to the HT-XRD analysis, the perovskite phase is formed at 450 °C for all the samples, regardless of the Sr content. The formation of a polyniobate phase with a tetragonal tungsten bronze structure was detected by HT-XRD in the KNN with the largest amount of Sr dopant, i.e., 6 mol% of Sr, at 600 °C.     

Intercalation of tris-(2,2′-bipyridyl) ruthenium (II) in α- and γ-zirconium phosphate: synthesis, thermal behaviour and X-ray characterization

Intercalation compounds such as the ruthenium trisbipyridyl complex in inorganic layered ion-exchangers (α- and γ-zirconium phosphate) have been synthesized using the batch method. There is no loss of bipyridyl ligand from the metal ion during the exchange of the ruthenium trisbipyridyl complex in these host matrices. The materials obtained are thermally stable up to ~330 °C (γ-phase) or ~380 °C (α-phase). The complex decomposition occurs in one or more steps and at ~600 °C the complex decomposition is complete. The X-ray patterns of ruthenium materials show a new phase with an increase in the interlayer distance with respect to the initial phase. Microanalysis measurements confirm the fact that the ruthenium complex is not modified when exchanged and the complex decomposition depends on its position in the host matrices.     

Photocatalytic behavior of α-Bi2Mo3O12 prepared by the Pechini method: degradation of organic dyes under visible-light irradiation

Nanoparticles of α-Bi₂Mo₃O₁₂ were prepared by the Pechini method. The process of formation of the bismuth molybdate was followed by simultaneous thermogravimetric and differential thermal analysis (TGA/DTA). Different samples of α-Bi₂Mo₃O₁₂ were obtained at 400, 450, and 500 °C, and characterized by X-ray powder diffraction (XRD), nitrogen physisorption (BET), and scanning electron microscopy (SEM). When observed by SEM, the morphology of the sample obtained at the lowest temperature consisted of semi-spherical particles with an average diameter of 150 nm. On the other hand, the highest calcination temperature led to the formation of sintered particles of 500–600 nm. The photocatalytic activity of α-Bi₂Mo₃O₁₂ was tested by photodegradation of the organic dyes rhodamine B (rhB) and indigo carmine (IC) under visible-light irradiation. The bismuth molybdate nanoparticles were able to bleach aqueous solutions of both organic dyes. The sample obtained at 400 °C was the best photocatalyst with half-lives, t _1/2, of 108 and 154 min for rhB and IC, respectively.     

Sol–gel synthesis of mesoporous WO3–TiO2 composite thin films for photochromic devices

Mesoporous WO₃–TiO₂ composite films were prepared by a sol gel based two stage dip coating method and subsequent annealing at 450, 500 and 600 °C. An organically modified silicate based templating strategy was adopted in order to obtain a mesoporous structure. The composite films were prepared on ITO coated glass substrates. The porosity, morphology, and microstructures of the resultant products were characterized by scanning electron microscopy, N₂ adsorption–desorption measurements, μ-Raman spectroscopy and X-ray diffraction. Calcination of the films at 450, and 500 °C resulted in mixed hexagonal (h) plus monoclinic phases, and pure monoclinic (m) phase of WO₃, respectively. The degree of crystallization of TiO₂ present in these composite films was not evident. The composite films annealed at 600 °C, however, consist of orthorhombic (o) WO₃ and anatase TiO₂. It was found that the o-WO₃ phase was stabilized by nanocrystalline anatase TiO₂. The thus obtained mesoporous WO₃–TiO₂ composite films were dye sensitized and applied for the construction of photochromic devices. The device constructed using dye sensitized WO₃–TiO₂ composite layer heat treated at 600 °C showed an optical modulation of 51 % in the NIR region, whereas the devices based on the composite layers heat treated at 450, and 500 °C showed only a moderate optical modulation of 24.9, and 38 %, respectively. This remarkable difference in the transmittance response is attributed to nanocrystalline anatase TiO₂ embedded in the orthorhombic WO₃ matrix of the WO₃–TiO₂ composite layer annealed at 600 °C.     

Synthesis and properties of magnetic fluids produced on the basis of magnetite particles

Magnetic fluids based on magnetite synthesized by the chemical condensation method at temperatures of 25, 40, 60, and 80°C were obtained and studied. Magnetite particles were examined by X-ray phase and X-ray fluorescence analyses and electron microscopy. The average size of the coherent scattering region of magnetite particles was 13–17 nm, depending on the synthesis temperature. Magnetic fluids were synthesized from magnetite particles obtained at 25 and 80°C, with water and octane serving as carrier fluids. The NMR method was used to determine the saturation magnetization and average magnetic moment of the particles: for water-based magnetic fluids, 2100 A m^–1 and 5.7 × 10^–19 A m² at magnetite particle synthesis temperature of 25°C and 3670 A m^–1 and 4.6 × 10^–19 A m² at magnetite particle synthesis temperature of 80°C; for octane-based magnetic fluids, 2250 A m^–1 and 4.1 × 10^–19 A m² at magnetite particle synthesis temperature of 25°C.