A simple simultaneous flow injection method based on phosphomolybdenum chemistry for nitrate and nitrite determinations in water and fish samples

A direct spectrophotometric flow injection method for the simultaneous determination of nitrite and nitrate has been developed. The method is based on the oxidation of a phosphomolybdenum blue complex by the addition of nitrite and the decrease in absorbance of the blue complex is monitored at 820 nm. The injected sample is split into two segments. One of the streams was directly reacted with the above reagent and detected as nitrite. The other stream was passed through a copperised cadmium reductor column where reduction of nitrate to nitrite occurs, and the sample was then mixed with the reagent and passed through the cell of the spectrophotometer to be detected as nitrite plus nitrate. The conditions for the flow injection manifold parameters were optimised by experimental design and the concentration of nitrite and nitrate was determined in the linear range from 0.05 to 1.15 mug ml(-1) nitrite and 0.06 to 1.6 mug ml(-1) nitrate with a detection limit of 0.01 mug ml(-1) for nitrite and 0.025 mug ml(-1) for nitrate. The method is suitable for the simultaneous determination of nitrite and nitrate in fish and water samples with a sampling rate of 25+/-2 sample per hour.     

Column-switching high-performance liquid chromatographic analysis of carbamazepine and its principal metabolite in human plasma with direct sample injection using an alkyl-diol silica (ADS) precolumn

In this paper, the on-line coupling of solid-phase extraction, based on a restricted-access support with high-performance reverse phase chromatography for the analysis of carbamazepine (CBZ) and carbamazepine-10,11-epoxide (CBZ-E) in human plasma samples is described. A precolumn packed with 25 mum C(18) alkyl-diol support is used for direct plasma injection. Using column-switching techniques, the analytes were enriched on the precolumn by a 5 mM phosphate buffer (pH 7) with 2% of methanol solution at a flow-rate of 0.8 ml min(-1), while proteins and endogenous hydrophilic substances in plasma were washed off to waste. The enriched analytes were then back-flushed onto the analytical C(18) column, separated by a mixture of 10 mM phosphate buffer (pH 7) acetonitrile (70:30 v/v) solution at a flow-rate of 1.0 ml min(-1) and detected by the ultraviolet absorbance set at 212 and 285 nm and without transfer loss. Linear calibration graphs were obtained for sample injection volumes of 50 (0.2-4.0 of mug of CBZ ml(-1) and 0.1-5.0 mug of CBZ-E ml(-1), respectively), and 20 mul (5.0-20.0 mug of CBZ ml(-1)); in either case the r-value was >0.9963. Recoveries from spiked plasma samples were quantitative for both analytes and the coefficients of variation were below 3.83%. The lowest samples concentrations that can be quantified with acceptable accuracy and precision was 0.2 mug CBZ ml(-1) and 0.1 mug CBZ-E ml(-1) when a sample volume of 50 mul was injected. Concentrations of 0.08 and 0.05 mug ml(-1) of CBZ and CBZ-E were considered the limit of detection for a signal-to-noise ratio of 3. Furthermore, the developed column-switching method was successfully applied to the determination of CBZ and CBZ-E in plasma samples of patients submitted to CBZ therapy.     

Simultaneous spectrophotometric determination of nitrite and nitrate by flow-injection analysis

An automatic direct spectrophotometric method for the simultaneous determination of nitrite and nitrate by flow-injection analysis has been developed. Nitrite reacts with 3-nitroaniline in the presence of hydrochloric acid (0.96-1.8 M HCl or pH 0.5-0.7) to form a diazonium cation, which is subsequently coupled with N-(1-naphthyl)-ethylenediamine dihydrochloride to form a stable purple azo dye, the absorbance of which is measured at 535 nm. Nitrate is reduced on-line to nitrite in a copper-coated cadmium column which is then treated with azo dye reagent and the absorbance due to the sum of nitrite and nitrate is measured; nitrate is determined from the difference in absorbance values. A copper column incorporated into the reaction manifold before the copperised cadmium column not only improves the long-term accuracy, but also extends the life time of the copperised cadmium column. Various analytical parameters, such as effect of acidity (pH), flow rate, sample size, dispersion coefficient, time, temperature, reagent concentration and interfering species, were studied. The calibration graphs were rectilinear for 0.1-3.5 mug ml(-1) of NO(3) and 10 ng ml(-1)-2.2mug ml(-1) of NO(2). The method is successfully applied to some food samples (meat, flour and cheese), environmental waters (inland and surface), beer and soil samples. Up to 30 samples can be analysed per hour with a relative precision of approximately 0.1-2%.     

Indirect laser-induced fluorescence detection for capillary electrophoresis using a frequency-doubled diode laser

A blue (452 nm) frequency-doubled diode laser with a quasi-cw optical output power of 10 microW is used for indirect laser-induced fluorescence detection in combination with the capillary electrophoretic separation of inorganic anions. As fluorescing probe ion the anion of 8-hydroxypyrene-1,3,6-trisulfonic acid (HPTS) was selected having an absorption maximum of 454 nm in alkaline medium. Employing a capillary coated with linear acrylamide, baseline separation of eight inorganic anions was possible within 5 min. With a separation buffer containing 50 micromol.L(-1) HPTS and 10 mmol.L(-1) lysine the limits of detection for sulfate, nitrite, nitrate, azide, thiocyanate, and chlorate were between 0.9 and 4.7 micromol.L(-1). Separation of chloride and sulfate was achieved by adding 0.25 mmol.L(-1) calcium hydroxide to the separation buffer. Inorganic anions in several mineral and tap water samples have been determined with the technique developed and results are compared to data obtained by ion chromatography in combination with conductivity detection after conductivity suppression.     

Simultaneous electrochemical determination of nitrate and nitrite in aqueous solution using Ag-doped zeolite-expanded graphite-epoxy electrode

In this work a new electrochemical sensor based on an Ag-doped zeolite-expanded graphite-epoxy composite electrode (AgZEGE) was evaluated as a novel alternative for the simultaneous quantitative determination of nitrate and nitrite in aqueous solutions. Cyclic voltammetry was used to characterize the electrochemical behavior of the electrode in the presence of individual or mixtures of nitrate and nitrite anions in 0.1 M Na₂SO₄ supporting electrolyte. Linear dependences of current versus nitrate and nitrite concentrations were obtained for the concentration ranges of 1-10 mM for nitrate and 0.1-1 mM for nitrite using cyclic voltammetry (CV), chronoamperometry (CA), and multiple-pulsed amperometry (MPA) procedures. The comparative assessment of the electrochemical behavior of the individual anions and mixtures of anions on this modified electrode allowed determining the working conditions for the simultaneous detection of the nitrite and nitrate anions. Applying MPA allowed enhancement of the sensitivity for direct and indirect nitrate detection and also for nitrite detection. The proposed sensor was applied in tap water samples spiked with known nitrate and nitrite concentrations and the results were in agreement with those obtained by a comparative spectrophotometric method. This work demonstrates that using multiple-pulse amperometry with the Ag-doped zeolite-expanded graphite-epoxy composite electrode provides a real opportunity for the simultaneous detection of nitrite and nitrate in aqueous solutions.     

Determination of tin in canned foods by UV/visible spectrophotometric technique using mixed surfactants

The complex of tin(IV) with bromopyrogallol red (BPR) in the presence of nonyl phenoxy polyethoxyethanol (OP) and cetyltrimethylammonium bromide (CTAB) has a sensitive absorption peak at 304 nm. Under the optimal conditions, Beer's law is obeyed over the range 0.1-2.5 mug ml(-1) Sn(IV) with molar absorptivity being 8.2 x 10(4) l mol(-1) cm(-1) and detection limit 0.018 mug ml(-1). As compared with the visible method which also uses BPR as chromogenic reagent (lambda(max) = 550 nm), our method is sensitive and selective because of the complex's high, sharp absorption peak. In addition, the present method is simple and rapid, no heating or standing is needed. By means of the mixed surfactants the precipitation caused by the ion association of cetyltrimethylammonium cation and I(-)(3) anion is avoided if iodide is used for separating micro amounts of tin(IV) from a sample matrix. An application of the proposed method to the determination of Sn(IV) in a canned food was made with satisfactory results.     

Spectrophotometric determination of bismuth and EDTA by means of the reaction of bismuth with pyrocatechol violet in the presence of septonex

The reaction of bismuth(III) with Pyrocatechol Violet in the presence of the cationic surfactant Septonex was studied and the optimal conditions for its analytical use were found (lambda = 612 nm, pH = 3.1, C(PV) = 4 x 10(-5)M, C(Sept), = 5 x 10(-4)M). The Lambert-Beer law is obeyed over the bismuth range 0.1-7.5 mug/ml. Decomposition of the Bi-PV-Septonex complex was utilized for indirect determination of ethylenediaminetetra-acetic acid at concentrations of 0.3-7.4 mug/ml.     

Determination of procaine, benzocaine and tetracaine by sequential injection analysis with permanganate-induced chemiluminescence detection

Local anaesthetics procaine hydrochloride (I), benzocaine (II), and tetracaine hydrochloride (III) were determined by the technique of sequential injection analysis (SIA) with chemiluminescence (CL) detection. The CL was emitted during the oxidation of the analytes by permanganate in aqueous sulphuric acid in the presence of various CL enhancers (4-hydroxybiphenyl, Rhodamine B, glycolaldehyde, glutaraldehyde and formic acid). The optimum enhancer or reagent concentrations, order and volumes of the injected zones were: 0.37 M formic acid (40, 23 or 28 mul for I-III, respectively), sample (40 mul), 2.3 M H(2)SO(4) (20, 16 or 18 mul for I-III, respectively), and 0.5 mM KMnO(4) (19, 13 or 15 mul for I-III, respectively). After a double (or single for III) reversal of the flow the mixed zone was pushed into the detector at a flow rate of 100 mul s(-1). The transient CL signal was recorded at >/=390 nm. The calibration graphs relating the intensity of the emission (peak heights) to the concentration of the analytes were curvilinear (a second order polynomial showed the best fit) and they were suitable for determining I-III in the ranges 0.5-50, 0.5-25 and 0.2-25 mug ml(-1), respectively. The limits of detection (3sigma) were 0.3 mug ml(-1) for I and II and 0.1 mug ml(-1) for III. The sample throughput was 120 h(-1). The relative standard deviations were 相似文献   

Mixed micellar medium for the spectrophotometric determination of molybdenum in molybdenum/tungsten mixtures

Effects of cetyltrimethylammonium bromide (CTAB) and/or nonylphenoxypolyethoxyethanol (OP) on the absorption spectra of the complexes of molybdenum and tungsten with bromopyrogallol red (BPR) were studied. Based on these effects, a mixture of CTAB and OP was thus selected as a medium for the selective and sensitive determination of Mo in Mo/W binary mixtures. Under the optimum conditions, Beer's law was obeyed over the range 0.06-0.8 mug ml(-1) Mo with molar absorptivity being 1.3x10(5) l mol(-1) cm(-1) and detection limit 0.025 mug ml(-1). For 1.0 mug Mo, at least 20 mug W did not interfere in the determination of Mo with average recovery and relative standard deviation being 99.5% and <2%, respectively. The method developed maintained the features of simplicity and rapidity and, moreover, its selectivity and sensitivity enhanced greatly due to the use of CTAB/OP mixed micellar medium. When coupled with a compatible concentration method, the proposed method could be used for the determination of trace Mo in natural waters.     

Determination of trace europium based on new fluorimetric system of europium(III) with thenoyltrifluoroacetone and N,N'-dinaphthyl-N,N'-diphenyl-3,6-dioxaoctanediamide

In the present paper, N,N'-dinaphthyl-N,N'-diphenyl-3,6-dioxaoctanediamide acts as a specific reagent for enhancing the fluorescence intensity of Eu(III) complex with thenoyl trifluoroacetone (TTA), the spectrofluorimetric determination of trace amounts of Eu(III) based on the above system was carried out and its luminescence mechanism was studied. The excitation and emission wavelengths are 343.6 and 613.3 nm, respectively. The fluorescence intensities vary linearly with the concentration of europium(III) in the range 3.647x10(-3)-3.039 mug ml(-1) for the original fluorescence with a detection limit down to 2.279x10(-4) mug ml(-1) and the standard deviation is 0.063 mug ml(-1) for 10 times measurements, and in the range 7.598x10(-4)-0.0243 mug ml(-1) (SD=0.035 for 15 times measurements), 0.06078-0.6100 mug ml(-1) (SD=0.52 for 10 times measurements) for the first derivative fluorescence signal with a detection limit down to 8.566x10(-5) mug ml(-1). The interferences of other rare earths and some of inorganic ions are described. This method is a direct, rapid, selective and sensitive analytical method for the determination of trivalent europium in rare earth ore samples and high purity of rare earth oxides.     

On the spectrophotometric flow injection determination of chromium(VI) in natural waters after on-line preconcentration on activated alumina

The feasibility of chromium(VI) preconcentration on to activated alumina in a continuous flow system with spectrophotometric detection was investigated. Chemical and flow variables, and the influence of concomitant species were studied both with and without preconcentration systems. The best results were obtained by using a 2.5 cm long, 1.6 mm i.d. alumina minicolumn, and selecting 1 x 10(-4) M nitric acid as the preconcentrating medium and 0.1 M ammonium hydroxide as the eluent. The eluted chromium(VI) was mixed with diphenylcarbazide in acidic medium and the absorbance of the colored complex was measured at 540 nm. Linear calibrations for 5, 25 and 50 ml sample volumes were established over the concentration ranges 10-50 mug 1(-1), 2-10 mug 1(-1) and 1-5 mug 1(-1) with sensitivity enhancements of 44, 196 and 392 and detection limits (3sigma) of 3.0 mug 1(-1), 0.3 mug 1(-1) and 0.2 mug 1(-1), respectively. The methods is relatively fast and cheap. Natural waters were analyzed with use of the developed procedure.     

Fluorimetric trace determination of cerium(III) with sodium triphosphate

Sodium triphosphate acts as a specific reagent for enhancing the fluorescence intensity of cerium(III). The purpose of this study was to investigate the spectrofluorimetric determination of trace amounts of Ce(III) in sodium triphosphate solution. The excitation and emission wavelengths are 303.5 nm and 353 nm respectively. Optimum sodium triphosphate concentration is found to be 0.074 g l(-1) at room temperature. The fluorescence varies linearly with the concentration of cerium(III) in the range 0.001-45 mug ml(-1). The detection limit is 9.4 x 10(-4)mug ml(-1). The relative standard deviations for 30 mug ml(-1) and 0.05 mug ml(-1) Ce(III) in 0.074 g l(-1) sodium triphosphate solution are 1.1% and 0.72% respectively. Quenching effects of other lanthanides and some inorganic anions are described. This method is a direct and rapid analytical method for the determination of Ce(III) in rare earth mixtures and cerium concentrates.     

Determination of sugars using ligand-exchange capillary electrophoresis

The capabilities of the ligand-exchange capillary electrophoresis mode (working electrolyte, 1 mM copper(II) and 175 mM NH3; 30 mbar, 10 s; +25 kV; 245 nm; 20°C) for the determination of sugars (glucose, fructose, and sucrose) in real samples (fruit juices, wines, and drug preparations) were studied. With the use of glucose as an example, the detection limits for direct (as sugar—copper(II) complexes; 245 nm) and indirect (working electrolyte, 5 mM tryptophan and 50 mM NaOH; 30 mbar, 10 s; +10 kV; 280 nm; 20°C) UV detection were compared: ≈21 and ≈8 mg/L (for direct and indirect detection, respectively).     

Development of a polypyrrole-based amperometric detector for the determination of certain anions in water samples

The development of a polypyrrole-based modified electrode for use in the detection of anions in flow-injection analysis and ion chromatography is described. Chloride, nitrate, nitrite, perchlorate, bromide, carbonate, sulphate and phosphate were detected by using flow-injection analysis combined with the polypyrrole-based CME electrochemical detector. All of the anions were detected conveniently and reproducibly over a linear concentration range 1-100 mug/ml. A detection limit of 0.1 mug/ml was obtained for chloride and a limit of 1.0 mug/ml for all of the other anions. Chloride, nitrate, sulphate and phosphate, following separation using ion chromatography, were detected simultaneously by using a conductivity detector and the polypyrrole-based CME electrochemical detector in series. Both methods of detection yielded similar results with comparable sensitivity, linearity and limits of detection. This method was then applied to the analysis of fresh water samples. The electrode was stable over a 2-week period of operation with no evidence of chemical or mechanical deterioration.     

Spectrophotometric determination of DNA using a near infrared probe 1,1'-disulfobutyl-3,3,3',3'-tetramethylindotricarbocyanine

A direct spectrophotometric determination of DNA in solution has been developed using a near infrared probe, 1,1'-disulfobutyl-3,3,3',3'-tetramethylindotricarbocyanine (DSTCY). In pH = 7.5 Tris-HCl buffer, the reaction of DSTCY with DNA was complete within 10 min at room temperature in the presence of cetyltrimethylammonium bromide (CTAB), which leaded to a sharp increase of the absorbance at 474 nm. The concentration of DNA can be determined in such wavelength with the linear range of 0.5-8.0 microg ml(-1) and the detection limit of 45 ng ml(-1).     

Identification and determination of active components in Angelica dahurica Benth and its medicinal preparation by capillary electrophoresis

A micellar electrokinetic capillary chromatography (MECC) method for the separation of three active components, imperatorin (IM), isoimperatorin (IO) and scopoletin (SC), in Angelica dahurica Benth and its preparation was developed. The optimum separation for these analytes was achieved using 10 mM borate, 20 mM SDS and 10%(v/v) acetonitrile, with applied voltage of 22 kV. All experiments were performed using a 50.0 cm (42.5 cm effective length)x75 mum I.D. fused-silica capillary. The linear calibration range was 12.0-800.0 mug ml(-1) for IM, 10.0-850.0 mug ml(-1) for IO and 3.5-600.0 mug ml(-1) for SC. The recoveries of three constituents were from 91.3 to 108.7%. Also, the dissociation constant (pKa) of SC was determined by the CE method established in this paper.     

Study of enzymatic reaction by electrophoretically mediated microanalysis in a partially filled capillary with indirect or direct detection

Electrophoretically mediated microanalysis (EMMA), in combination with a partial filling technique and indirect or direct detection, is described for the study of enzymes reacting with the high mobility inorganic or organic anions as substrates or products. Part of the capillary is filled with a buffer optimized for the enzymatic reaction, the rest of the capillary with the background electrolyte being optimal for the separation of substrates and products. With haloalkane dehalogenase, chosen as a model enzyme, the enzymatic reaction was performed in a 20 mM glycine buffer (pH 8.6). Because of the wide substrate specificity of this enzyme, utilizing chlorinated as well as brominated substrates and producing either nonabsorbing chloride or absorbing bromide ions, two different background electrolytes and detection approaches were adopted. A 10 mM chromate-0.1 mM cetyltrimethylammonium bromide background electrolyte (pH 9.2) was used in combination with indirect detection and 20 mM beta-alanine-hydrochloric acid (pH 3.5) in combination with direct detection. The Michaelis constant (K(m)) of haloalkane dehalogenase for 1-bromobutane was determined. The K(m) values 0.59 mM estimated by means of indirect detection method and 0.17 mM by means of direct detection method were comparable with the value 0.13 mM estimated previously by gas chromatography.     

Simultaneous determination of naproxen, salicylic acid and acetylsalicylic acid by spectrofluorimetry using partial least-squares (PLS) multivariate calibration

Determination of naproxen, salicylic acid and acetylsalicylic acid has been carried out in mixtures of up to three components by recording emission fluorescence spectra between 300 and 520 nm with an excitation wavelength of 290 nm. The excitation-emission spectra of these compounds are strongly overlapped, which does not permit their direct determination without previous separation by conventional methodologies. Here, a method is proposed for the determination of these chemicals by the use of a full-spectrum multivariate calibration method, partial least-squares (PLS). The experimental calibration matrix was designed with 18 samples. The concentrations were varied between 0.1 and 1.0 mug ml(-1) for naproxen, 0.5 and 5.0 mug ml(-1) for salicylic acid and from 2.0 to 12.0 mug ml(-1) for acetylsalicylic acid. The cross-validation method was used to select the number of factors. To check the accuracy of the proposed method, the optimized model, obtained using PLS-1, was applied to the determination of these compounds in pharmaceuticals and human serum samples previously spiked with different amounts of each chemical.     

Analysis of aesculin and aesculotin in Cortex fraxini by capillary zone electrophoresis

A simple method for quantitative analysis of aesculin and aesculetin in Cortex fraxini was developed using capillary zone electrophoresis (CZE). Berberin was employed as an internal standard, The running buffer was 6 mM Na(2)B(4)O(7) and 10 mM NaH(2)PO(4) (pH 6.70). The linear calibration range was 32-256 mug ml(-1) (r=0.9996) for aesculin and 23-230 mug ml(-1) (r=0.9993) for aesculetin. The contents of aeculin and aesculetin in C. fraxini were easily determined within 12 min the pKa values of aesculin and asculetin determined by CZE were 6.56 and 5.62, respectively. A simple method for estimation of the temperature inside the capillary during running was also proposed.     

A comparative study on various spectrometries with thin layer chromatography for simultaneous analysis of drotaverine and nifuroxazide in capsules

Three spectrophotometric methods including Vierordt's method, derivative, ratio spectra derivative, and thin layer chromatography (TLC)-UV densitometric method were developed for simultaneous determination of drotaverine HCl (DRT) and nifuroxazide (NIF) in presence of its impurity, 4-hydroxybenzohydrazide (4-HBH). In Vierordt's method, (E(1 cm)(1%)) values were calculated at 227 and 368 nm in the zero-order spectra of DRT and NIF. By derivative spectrophotometry, the zero-crossing method, drotaverine HCl was determined using the second derivative at 245 nm and the third derivative at 238 nm, while nifuroxazide was determined using the first derivative at 399 nm and the second derivative at 411 nm. The ratio spectra derivative spectrophotometry is basedon the measure of the amplitude at 459 nm for DRT and at 416 nm for NIF in the first derivative of the ratio spectra. Calibration graphs of the three spectrophotometric methods were plotted in the range 1-10 mug/ml of DRT and 2-20 mug/ml of NIF. TLC-UV densitometric method was achieved on silica gel plates using ethyl acetate : methanol : ammonia 33% (10 : 1 : 0.1 v/v/v) as the mobile phase. The Rf values were 0.74, 0.50, 0.30+/-0.01 for DRT, NIF and 4-HBH, respectively. On the fluorescent plates, the spots were located by fluorescence quenching and the densitometrical area were measured at 308 and 287 nm with linear range 0.2-4 mug/spot and 0.6-12 mug/spot for DRT and NIF, respectively. The proposed methods have been successfully applied to the commercial pharmaceutical formulation without any interference of excipients. Mean recoveries, relative standard deviations and the results of the proposed methods were compared with those obtained by applying the alternate methods.