Solid-state ion selective electrode based on polypyrrole conducting polymer nanofilm as a new potentiometric sensor for Zn2+ ion

A pencil graphite electrode (PGE) electrodeposited by a polypyrrole conducting polymer doped with tartrazine (termed as PGE/PPy/Tar) was prepared and used as a zinc (II) solid-state ion-selective electrode. For the preparation of the zinc sensor electrode, electrodeposition of a polypyrrole nanofilm was carried out potentiostatically (E _app?=?0.75 V vs SCE) in a solution containing 0.010 M pyrrole and 0.001 M tartrazine trisodium salt. A pencil graphite and Pt wire were used as working and auxiliary electrodes, respectively. The introduced electrode in the current paper can be fabricated simply and was found to possess high selectivity, exhibited wide working concentration range, sufficiently rapid response, potential stability, and very good sensitivity to Zn (II) ion. The sensor electrode showed a linear Nernstian response over the range of 1.0?×?10^?5 to 1.0?×?10^?1 M with a slope of 28.23 mV per decade change in zinc ion concentration. A detection limit of 8.0?×?10^?6 M was obtained. The optimum pH working of the electrode was found to be 5.0.     

Potentiometric determination of sulfonamides with a silver sulfide electrode

The silver sulfide membrane electrode shows well-defined responses to several pharmaceutically important sulfonamides over the concentration range 10^-1–10^-4 M. Both direct and titrimetric determinations of sulfonamides are described and applied to pharmaceutical dosage forms.     

Potentiometric propranolol-selective sensor based on molecularly imprinted polymer

A novel potentiometric sensor based on molecularly imprinted polymer (MIP) for propranolol, an adrenergic-blocking drug, was designed. The influence of molecularly imprinted polymer particle content and sodium tetraphenylborate additives in polyvinylchloride membrane was shown. The electrodes show near-Nernstian responses down to 10^?4–10^?5?M propranolol concentration. The potentiometric response of MIP-based sensor for propranolol in mixed nonaqueous medium was shown at first. Sensor selectivity relative to various inorganic cations, atenolol and metoprolol, was reported. Direct potentiometry was used to determine propranolol in aqueous modeling solutions and pharmaceutical preparations with good results.     

Calcium ion selective membrane electrode

The calcium salts of the mono- and diesters of [4-(1,1,3,3-tetramethylbutyl)phenyl phosphoric acid] have been prepared, and the individual esters as well as mixtures of the esters have been used with several varieties of polyvinyl chloride to construct macro membrane electrodes selective to calcium ions. These electrodes have been calibrated by using solutions of CaCl₂ and Ca ion buffers. The mixed ester electrodes showed Nernstian response in the concentration range 10^-1 to 10^-7M; the diester electrodes showed Nernstian response down to 7.9 x 10^-8M. The detection limit of the mixed ester electrode was 10^-8M, whereas that of the diester electrode was 7.9 x 10^-9M. Contrary to these results, the monoester electrodes showed unsatisfactory behavior. The responses of both the mixed ester and diester electrodes to calcium ions were not affected by the presence of sodium, potassium, or other divalent ions. Only ferric and lanthanum ions showed interferences with the electrode response to calcium ions. p]The electrode response was independent of pH in the approximate range 5–8 at a CaCl₂ concentration of 10^-4M. As the Ca ion concentration was increased, the range of pH independence widened to approximately 4–8. The dynamic response time constant of the mixed ester electrode was in the range 0.7–1.5 sec, whereas that of the diester electrode was in the range 0.5–0.75 sec.     

Potentiometric sensor for sensitive and selective detection of heparin

A polymeric membrane ion-selective electrode for determination of heparin is described in this paper.Protamine is incorporated into the organic membrane phase and functions as sensing element for selective recognition of heparin.The proposed membrane electrode exhibits high selectivity for heparin over lipophilic anions such as thiocyanide and salicylate.The potentiometric response to the concentration of heparin is Unear in the range of 0.01-0.4 U/mL and a lower detection limit of 0.005 U/mL can be achieved.     

茜素S选择电极的研制和应用

本文报道了茜素S电极的研制和应用。比较了季铵盐、季鏻盐、碱性染料和邻二氮菲金属配合盐作为活性物质、各种介体溶剂以及活性物质在膜相中的含量对电极性能的影响。以三辛基甲基氯化铵制成的PVC膜型电极对茜素S在2×10~(-4)～5×10~(-7)M浓度范围内呈Nernstian响应,检测下限为2×10~(-7)M。测定了一些阴离子的选择系数,ClO_4~-,CNS~-,I~-以及能与茜素S配合的金属离子有明显干扰。报道了以茜素S电极为指示电极,用EDTA和茜素S为滴定剂滴定钪和稀土的情况。以茜素8电位滴定钪及钴-钐合金中的钐,都获得良好的结果。     

Preparation and application of a new glucose sensor based on iodide ion selective electrode

An electrode for glucose has been prepared by using an iodide selective electrode with the glucose oxidase enzyme. The iodide selective electrode used was prepared from 10% TDMAI and PVC according our previous study. The enzyme was immobilized on the iodide electrode by holding it at pH 7 phosphate buffer for 10 min at room temperature. The H₂O₂ formed from the reaction of glucose was determined from the decrease of iodide concentration that was present in the reaction cell. The iodide concentration was followed from the change of potential of iodide selective electrode. The potential change was linear in the 4×10⁻⁴ to 4×10⁻³ M glucose concentration (75-650 mg glucose/100ml blood) range. The slope of the linear portion was about 79 mV per decade change in glucose concentration. Glucose contents of some blood samples were determined with the new electrode and consistency was obtained with a colorimetric method. The effects of pH, iodide concentration, the amount of enzyme immobilized and the operating temperature were studied. No interference of ascorbic acid, uric acid, iron(III) and Cu(II) was observed. Since the iodide electrode used was not an AgI-Ag₂S electrode, there was no interference of common ions such as chloride present in biological fluids. The slope of the electrode did not change for about 65 days when used 3 times a day.     

Potentiometric determinations with the silver sulfide membrane electrode : Part I. Determination of cyanide

The possibilities of the silver sulfide membrane electrode for the determination of cyanide are described; determinations by multiple standard addition and titration have been studied, and interferences have been checked. The determination of cyanide in solutions containing various metal complexes, and the evolution method for separation of hydrogen cyanide are discussed. Automatic titration can be used for samples containing 1 p.p.m. cyanide, and the standard addition method for 1 p.p.b. cyanide.     

溶胶-凝胶硫离子传感器的研制及应用

报道了溶胶 凝胶硫离子传感器的制备方法及其在硫离子检测中的应用。采用循环伏安法(CV)对传感器修饰过程进行了表征,对其电化学过程的可行性及其响应机理进行了探讨。传感器在6.0×10-7～1.0mol L范围内符合Nernst方程式,线性相关系数r=0.9991,方法的检出限为2.0×10-7mol L。于4℃干态保存4周,响应信号基本不变,已用于环境水样的分析。     

Conducting polymer membranes for low activity potentiometric ion sensing

Conducting polymer (CP) films, used as ion-sensing membranes under open circuit potentiometric conditions, are usually characterised with rather high detection limit, in the range of 10⁻⁴-10⁻⁵ mol dm⁻³. This effect is unfavourable, not only from the point of view of CP applications in potentiometry as ion sensitive membranes, but also when these materials are used as ion-to-electron transducers (solid contacts) for ion-selective electrodes. The theoretical considerations presented underline the crucial role of spontaneous processes of polymer charging/discharging—the source of observed high detection limit of sensors comprising CP layer under zero current conditions. Although the mechanism of occurring process is different from that observed for plastic, solvent polymeric based ion-selective electrodes, the ultimate result—alteration of activity of electrolyte at the membrane/solution interface leading to elevation of the detection limit—is the same.The method of estimation of parameters characterising spontaneous charge transfer processes is presented. The values obtained can be used to calculate the resulting polymer/solution interface activity of electrolyte ions, thus the detection limit of CP membrane can be theoretically predicted.A method of lowering of the detection limit of conducting polymer membranes, applying galvanostatic polarisation to compensate the spontaneous process of polymer charging/discharging, is presented.The experimental results obtained for poly(pyrrole), poly(N-methylpyrrole) and poly(3,4-ethylenedioxythiophene) are in good accordance with predictions of the presented model.     

Potentiometric determinations with the silver sulfide membrane electrode : Part II. Determination of Sulfur Compounds

A simple, sensitive and fast titrinetric method for sulfur determinations with the silver sulfide membrane electrode is described. Sulfide and sulfate can be determined in one sample. A sensitive sulfate determination is possible after reduction with hydrogen iodide—sodium hypophosphite—acetic acid. Other inorganic sulfur compounds can also be determined. Sparingly soluble metal sulfides can be determined after treatment with strong acid. A reduction with Raney nickel is suitable for the estimation of elementary sulfur and organic sulfur compounds; combustion of the samples in an oxygen flask may be necessary. The methods outlined are applied to the determination of sulfur in steel, some petroleum products and aerosols. When different methods are used, different kinds of sulfur compounds present in an unknown sample can be distinguished.     

Highly selective electrogenerated chemiluminescence (ECL) for sulfide ion determination at multi-wall carbon nanotubes-modified graphite electrode

In the present work, a novel method for immobilization of carbon nanotubes (CNTs) on the surface of graphite electrode was proposed. We further found that superoxide ion was electrogenerated on this CNTs-modified electrode, which can react with sulfide ion combing with a weak but fast electrogenerated chemiluminescence (ECL) emission, and this weak ECL signal could be enhanced by the oxidative products of rhodamine B. In addition, the rate constant of this electrochemical reaction k⁰ was investigated and confirmed that the speed of electrogenerating superoxide ion was in accordance with the subsequent fast CL reaction. Thus, the fast CL reaction of superoxide ion with target brought in the possibility of high selectivity based on time-resolved, relative to other interferences. Based on these findings, an excellently selective and highly sensitive ECL method for sulfide ion was developed. Under the optimum conditions, the enhancing ECL signals were linear with the sulfide ion concentration in the range from 6.0 × 10⁻¹⁰ to 1.0 × 10⁻⁸ mol L⁻¹, and a 2.0 × 10⁻¹⁰ mol L⁻¹ detection limits (3σ) was achieved. In addition, the proposed method was successfully used to detect sulfide ion in environmental water samples.     

Potentiometric detection in ion chromatography using a metallic copper indicator electrode

Summary A metallic copper electrode housed in a suitable flowcell is shown to be a sensitive and versatile potentiometric detector for ion chromatography. This electrode may be used for direct or indirect detection of many inorganic anions and cations and also for organic acids. In the direct detection mode, electrode response is based on either complexation of copper ions at the electrode surface by eluted species, or on oxidation and reduction reactions for eluted species which are strong oxidants or reductants. Direct detection is therefore applicable to such species as amino acids, organic acids, chloride, bromide, iodide, chlorate, bromate and iodate. Indirect detection is possible for anions which do not complex copper ions, provided a copper complexing ligand (such as phthalate) is used in the eluent; cations which complex this ligand are also detectable. Indirect detection may be used for species such as nitrite, nitrate, acetate, formate, succinate, benzoate, alkaline earth ions and transition metal ions. Electrode calibration relationships are discussed and sample separations are presented, together with some typical detection limits attainable in the direct and indirect detection modes.Presented in part at a National Symposium on Ion Chromatography, held at the University of New South Wales, Kensington, Australia, Nov. 21, 1984.     

Potentiometric enzyme electrode for uric acid.

An enzyme electrode for uric acid, with immobilized uricase on a pCO₂ membrane electrode, is described. Evaluation studies show that the enzyme electrode attains performance characteristics similar to homogeneous enzymatic conversion of uric acid under optimum solution conditions. Comparison of analyses carried out with the enzyme electrode and classical procedures on urine control samples demonstrates acceptable accuracy and precision for the electrode method.     

Preparation and application of selenite ion selective electrode

A new selenite ion selective electrode using 4,6-dibromopiaselenole as active material, PVC as membrane matrix and dibutyl phthalate as plasticizer has been developed. An analytically useful potential change occurs from about 10(-6)-10(-1)M Se(IV), and the slope of the linear portion is -23.6 mV/10-fold change in Se(IV) concentration at a temperature of 21 degrees . The electrode shows fairly good selectivity for selenite ion over other anions and has been used for the successful determination of total selenium in human hair.     

Potentiometric estimation of sulfide ion using the Fe(III)-EDTA complex

The Fe(III)-EDTA complex reacts with sulfide ion in a fast electron transfer reaction, oxidising the latter to elemental sulfur and getting itself reduced to Fe(II). The reaction has been developed for the quantitative estimation of sulfide ion by titration against the Fe(III)-EDTA complex, measuring the redox potential of the system. Repeated use of a given quantity of the complex solution by the process of regeneration has been demonstrated. The possibility of its practical application in liquid phase oxidation processes of recovering sulfur from H₂S is emphasized.     

Highly-sensitive ion selective electrode based on molecularly imprinted polymer particles for determination of tetracycline in aqueous samples

In this work, a highly-sensitive polymeric membrane ion selective electrode for determination of tetracycline was constructed by using molecularly imprinted polymer (MIP) particles as quasi-ionophore. The water-compatible MIP particles targeting tetracycline were synthesized with tetracycline as a template molecule, methacrylic acid as a functional monomer, ethylene glycol dimethacrylate as a cross-linker, 2,2′-azobisisobutyronitrile as an initiator and lanthanum ion as a mediator. Benefited from the distinctive performance of the quasi-ionophore and the optimized composition of the membrane and the inner filling solution, the lower detection limit of the electrode was decreased to about 1 × 10⁻⁸ mol/l. It exhibited a good electrode slope 59.8 mV/decade near the theoretical Nernstian one, with a wide linear working range from 2.0 × 10⁻⁸ to 1.0 × 10⁻³ mol/l. Due to the specific recognition of tetracycline by the MIP particles, the selectivity coefficients for routine interferences were less than 10⁻⁴. The fabricated electrode should be used in pH 2–4, response time of which was less than 200 s when the concentration of tetracycline was higher than 1.0 × 10⁻⁶ mol/l and no more than 30 min at the concentration of 1.0 × 10⁻⁸ mol/l. Finally, the proposed highly-sensitive ion selective electrode has been successfully applied to the determination of tetracycline in aqueous samples.     

A novel ion selective sensor for promethium determination

This is a first promethium(145) ion-selective sensor based on the comparative study of two Schiff base ligands (X(1) and X(2)) as neutral ionophores. Effect of various plasticizers: 2-nitrophenyloctylether (o-NPOE), dibutyl phosphonate (DBP), dioctylphthalate (DOP), tri-(2-ethylhexyl) phosphate (TEHP), dibutyl butylphosphonate (DBBP), chloronaphthalene (CN) and anion excluders: potassium tetrakis (p-chloropheny1) borate (KTpClPB), sodiumtetraphenylborate (NaTPB) and oleic acid (OA) have been studied. The membrane with a composition of ionophore (X(1)/X(2)):KTpClPB:PVC:o-NPOE (w/w, %) in the ratio of 5:5:30:60 exhibited best performance. The best responsive membrane sensors (8 and 21) exhibited working concentration range of 4.5×10(-7)-1.0×10(-2) M and 3.5×10(-6)-1.0×10(-2) M with a detection limits of 3.2×10(-7) M and 2.3×10(-6) M and Nernstian slopes of 20.0±0.5, 19.5±0.5 mV decade(-1) of activity, respectively. The sensor no. 8 works satisfactorily in partially non-aqueous media up to 10% (v/v) content of methanol, ethanol and acetonitrile. Analytical application of the proposed sensor has been demonstrated in determination of promethium (III) ions in spiked water samples.     

Potentiometric Cr(VI) selective electrode based on novel ionophore-immobilized PVC membranes

For the determination of Cr(VI) concentrations with a potentiometric ion-selective electrode (ISE), ionophore-immobilized membranes were prepared by ultraviolet (UV)-induced graft polymerization followed by chemical treatment. Novel ionophores comprising various amine structures were immobilized onto poly(vinyl chloride) (PVC) matrixes, and these were examined to determine Cr(VI) selectively. Of the three ionophores examined in this study, the membranes with N,N,N,N-tetrakis(3-aminopropyl)-1,4-butanediamine (DABAm4) exhibited the highest Cr(VI) ion selectivity in both extraction and potentiometry experiments. The plasticizer in the membrane was optimized as 1.0 ml o-nitrophenyl octyl ether (NPOE)/g PVC to form diffusible channels. The potentiometric studies revealed that the performance of DABAm4-immobilized PVC was equivalent to that of mobile ionophores in supported liquid membranes (SLMs). A reproducible response of Cr(VI) was attained within a response time of 1 s in the range of 2.16 × 10⁻⁶ to 0.1 M, using the membrane prepared in this study. The selectivity for the Cr(VI) ion against the other interfering ions was compared reasonably between a solvent extraction and potentiometry. The long-term response of the Cr(VI) ISE showed slight deterioration over a continuous operation for 6 months, while the detection limit slightly decreased due to the leaching-out of the plasticizer. The ISE along with the DABAm4 immobilized membrane showed a higher Cr(VI) ion selectivity and more stable response under long-term usage than ISEs with typical SLMs.     

Potentiometric response and mechanism of anionic recognition of heterocalixarene-based ion selective electrodes

The ion selective electrode (ISE)-based potentiometric approach is shown to be an effective means of characterizing the anion recognition sites in the molecular receptor calix[2]pyridino[2]pyrrole (CPP). In particular, potentiometric pH-measurements involving the use of experimental PVC-membranes based on CPP revealed the existence of both mono- and diprotonated forms of the receptor under readily accessible conditions. Based on these analyses, apparent surface protonation constants for this heterocalixarene were found to lie between 8.5-8.9 (pK_B1) and 3.3-3.8 (pK_B2). CPP was found to interact with targeted anionic analytes based on both coulombic and hydrogen bond interactions, as inferred from varying the kinds of ionic sites present within the membrane phase. Potentiometric selectivity studies revealed that CPP preferred “Y-shaped” anions (e.g. acetate, lactate, benzoate) over spherical anions (e.g. fluoride and chloride), fluoride over chloride within the set of spherical anions, and the ortho-isomer over the corresponding meta- and para-isomers in the case of hydroxybenzoate (salicylate and congeners). In the context of this study, the advantages of potentiometric determinations of acetylsalicylic acid using optimized PVC-membranes based on CPP relative to more conventional PVC-membrane ISEs based on traditional anion exchanger were also demonstrated.