Spectrofluorimetric kinetic determination of selenium (IV) by flow injection analysis in cationic micellar medium

A sensitive catalytic kinetic spectrofluorimetric method for determining ng ml(-1) of selenium by flow injection analysis has been developed. The method, based on the catalytic effect of Se (IV) on the reduction of resorufin by sulphide, in the presence of cetylpyridinium chloride, is monitored spectrofluorimetrically (lambda(ex)=480 nm; lambda(em)=583 nm). The linearity range of the calibration graph is dependent on the concentration of sulphide. The variables affecting the rate of the reaction were investigated. The method is simple, rapid, precise, sensitive, and widely applicable. The limit of detection is 1 ng ml(-1) Se (IV), and the calibration range is 5-1000 ng ml(-1). Sampling rate is 60 samples h(-1), and the relative standard deviation of 12 determinations of 100 ng ml(-1) Se was 0.76%. The determination of Se (IV) in the presence of Se (VI) and total selenium is described. The method was applied to the determination of Se in selenium tablets, and several synthetic samples.     

Separation and determination of selenium(IV) and molybdenum(VI) in mixtures by selective precipitation with potassium thiocarbonate

A simple method for the separation and determination of selenium(IV) and molybdenum(VI) in mixtures, based on selective precipitation with potassium thiocarbonate, has been developed. The procedure allows quantitative determination of 10-100 mg of selenium or 10-70 mg of molybdenum at pH 0.5-1.0. No interference by a wide range of other metal ions is observed.     

Determination of trace selenium by solid substrate-room temperature phosphorescence enhancing method based on potassium chlorate oxidizing phenyl hydrazine-1,2-dihydroxynaphthalene-3,6-disulfonic acid system

A new method for the determination of trace selenium based on solid substrate-room temperature phosphorimetry (SS-RTP) has been established. This method was based on the fact that in HCl-KCl buffer solution, potassium chlorate could oxidize phenyl hydrazine to form chloridize diazo-ion after being heated at 100 degrees C for 20 min, and then the diazo-ion reacted with 1,2-dihydroxynaphthalene-3,6-disulfonic acid to form red azo-compound which could emit strong room temperature phosphorescence (RTP) signal on filter paper. Selenium could catalyze potassium chlorate oxidizing the reaction between phenyl hydrazine and 1,2-dihydroxynaphthalene-3,6-disulfonic acid, which caused the sharp enhancement of SS-RTP. Under the optimum condition, the relationship between the phosphorescence emission intensity (DeltaIp) and the content of selenium obeyed Beer's law when the concentration of selenium is within the range of 1.60-320 fg spot-1 (or 0.0040-0.80 ng ml-1 with a sample volume of 0.4 microl). The regression equation of working curve can be expressed as DeltaIp=13.12+0.4839CSe(IV) (fg spot-1) (n=6), with correlation coefficient r=0.9991 and a detection limit of 0.28 fg spot-1 (corresponding to a concentration range of 7.0x10(-13) g ml-1 Se(IV), n=11). After 11-fold measurement, R.S.D. were 2.8 and 3.5% for the samples containing 0.0040 and 0.80 ng ml-1 of Se(IV), respectively. This accurate and sensitive method with good repeatability has been successfully applied to the determination of trace selenium in Chinese wolfberry and egg yolk with satisfactory results. The mechanism of the enhancement of phosphorescence was also discussed.     

Kinetic-spectrophotometric determination of selenium in natural water after preconcentration of elemental selenium on activated carbon

A simple, accurate, sensitive and selective method is described for rapid determination of ultra-trace quantities of selenium. Selenium (IV) was collected on activated carbon after reduction to elemental Se by l-ascorbic acid. The collected selenium was then determined based on its accelerating effect on the oxidation reaction of methyl orange with bromate in acidic media. Total amount of Se(IV) and Se(VI) were collected on AC after their reduction by hydrazine. Se(IV), Se(VI) and total selenium could be determined by the method. Selenium in the range 10-10 000 ng could be determined by the method. The method was used to the determination of Se(IV), Se(VI) and total selenium in natural water with satisfactory results.     

Kinetic spectrophotometric determination of trace amounts of selenium and vanadium

A sensitive kinetic spectrophotometric method has been developed for the determination of Se(IV) over the range of 45 to 4000 ng in 10 mL of solution. The method is based on the catalytic effect of Se(IV) on the reduction reaction of bromate by hydrazinium dichloride, with subsequent reaction of Ponceau S with products of the above reaction (chlorine and bromine), causing color changing of Ponceau S. Method development includes optimization of time interval for measurement of slope, pH, reagents concentration, and temperature. The optimized conditions yielded a theoretical detection limit of 33 ng/¶10 mL of solution of Se(IV). The interfering effects were studied and removed. The method was applied to the determination of selenium in spiked water, Kjeldahl tablet, selenium tablet, and shampoo. Vanadium(V) has an inhibition effect on the catalyzed reaction of bromate and hydrazine by selenium. Using this effect, V(V) can be determined in the range of 70 to 2500 ng in 10 mL of solution. The optimization procedure includes pH and selenium concentration. An extraction method was used for interference removal. The method was applied to the determination of vanadium in petroleum.     

A highly sensitive colour reaction for Se(IV) with the iodide-rhodamine B-PVA system Spectrophotometric determination of trace amounts of selenium in water

A highly sensitive spectrophotometric method for determination of selenium(IV) has been developed, based on Se(IV) oxidation of I(-) to I(-)(3) in a weak-acid medium, then formation of the 1:1 ion-association complex of I(-)(3) with Rhodamine B in the presence of poly(vinyl alcohol). The molar absorptivity is 1.97 x 10(5)l.mole(-1).cm(-1). Preconcentration of Se(IV) and elimination of interfering ions is achieved by an improved thiol cotton method, so the determination has very good selectivity. Se(IV) at mug/l. levels in tap water, hot-spring water and river water has been satisfactorily determined by the method.     

Determination of inorganic selenium species by miniaturised isotachophoresis on a planar polymer chip

The use of miniaturised isotachophoresis to allow the simultaneous determination of two inorganic selenium species has been investigated using a poly(methyl methacrylate) chip with a 44-mm-long, 200-microm-wide, 300-microm-deep separation channel. The miniaturised device included an integrated on-column, dual-electrode conductivity detector and was used in conjunction with a hydrodynamic fluid transport system. A simple electrolyte system has been developed which allowed the separation of selenium(IV) and selenium(VI) species to be made in under 210 s. The limits of detection were calculated to be 0.52 mg L(-1) for selenium(IV) and 0.65 mg L(-1 )for selenium(VI). The method allowed the separation of the selenium species from a range of common anions including fluoride, nitrate, nitrite, phosphate, sulfate and sulfite.     

Flow-injection simultaneous determination of selenium(IV) and selenium(IV + VI) using photooxidative coupling of p-hydrazinobensenesulfonic acid with N-(1-naphthyl)ethylenediamine

A flow-injection spectrophotometric method has been developed for the simultaneous determination of selenium(IV) and (IV + VI) at nanogram per milliliter levels. It is based on the catalytic effect of selenium(IV) on the photooxidative coupling of p-hydrazinobenzenesulfonic acid (HBS) with N-(1-naphthyl)ethylenediamine (NED) to form an azo dye (λ_max = 538 nm). In this reaction, bromide acted as an activator for the catalysis of selenium(IV) and an reducer for selenium(VI) to selenium(IV) in an acidic medium which allowed the determination of selenium(IV + VI). A sample solution, being split by Y-piece into two portions, passed through the low-temperature coil (4 m, 25 °C) and the high-temperature coil (20 m, 100 °C). By monitoring the absorbance of the dye produced in the two portions, selenium(IV) and (IV + VI) in the range of 0.2–6 ng ml⁻¹ were determined simultaneously. The relative standard deviations for 3 ng ml⁻¹ selenium(IV) and (VI) (n = 10) were 1.2 and 1.3%, respectively. There were few interfering ions in the selenium determination. The proposed method was applied to the determination of selenium(IV) and (VI) in natural water samples.     

Kinetic spectrophotometric determination of trace amounts of selenium and vanadium

A sensitive kinetic spectrophotometric method has been developed for the determination of Se(IV) over the range of 45 to 4000 ng in 10 mL of solution. The method is based on the catalytic effect of Se(IV) on the reduction reaction of bromate by hydrazinium dichloride, with subsequent reaction of Ponceau S with products of the above reaction (chlorine and bromine), causing color changing of Ponceau S. Method development includes optimization of time interval for measurement of slope, pH, reagents concentration, and temperature. The optimized conditions yielded a theoretical detection limit of 33 ng/?10 mL of solution of Se(IV). The interfering effects were studied and removed. The method was applied to the determination of selenium in spiked water, Kjeldahl tablet, selenium tablet, and shampoo. Vanadium(V) has an inhibition effect on the catalyzed reaction of bromate and hydrazine by selenium. Using this effect, V(V) can be determined in the range of 70 to 2500 ng in 10 mL of solution. The optimization procedure includes pH and selenium concentration. An extraction method was used for interference removal. The method was applied to the determination of vanadium in petroleum. Received: 20 October 1998 / Revised: 17 April 1999 / Accepted: 3 June 1999     

Cathodic stripping voltammetric determination of selenium(IV) at a thin-film mercury electrode in a thiocyanate-containing electrolyte

The well-known method for the determination of selenium(IV), which is based on the cathodic stripping voltammetry of copper(I) selenide, has been adapted for application at the thin-film mercury electrode on glassy carbon (TFME). Insufficient reproducibility and sensitivity have been overcome by using a 0.1 mol/L HClO₄ electrolyte solution containing 0.02 mol/L thiocyanate ions. Thiocyanate ions have been found to increase the peak height of the selenium response and shift it to more positive potentials. This behaviour is explained by an adsorption of SCN^– at the interface glassy carbon/Cu₂Se and its action as an electron transfer catalyst between glassy carbon and copper(I) selenide. A 3σ-detection limit of 75 ng/L Se^(IV) has been achieved. The relative standard deviation is 5.2% at 5 μg/L selenium(IV). The influence of cadmium(II), arsenic(III), zinc(II), iron(III) and lead(II) ions on the selenium response has been studied. In case of lead ions, a new signal occurred at more negative potentials than the reduction of Cu₂Se. This signal, which is probably due to the reduction of PbSe, can also be used for the determination of selenium(IV).     

Anion-exchange resin modified with bismuthiol-II, as a new functional resin for the selective collection of selenium(IV)

A functional resin for the collection of selenium(IV) has been prepared simply by the conversion of a common ion-exchange resin with bismuthiol-II which has three functional properties, namely the capabilities of selective reaction with selenium(IV), ion-exchange reaction with ion-exchange resin and strong physical sorption to the ion-exchange resin matrix. The binding ratio of selenium(IV) to bismuthiol-II on the resin was confirmed to be 1:4. The reaction was represented as follows: 4RSH + H(2)SeO(3)--> R-S-Se-S-R + R-S-S-R + 3H(2)O. Highly selective sorption of selenium(IV) was achieved, based on the formation of stable selenotrisulphide on the resin. Selenium(IV) sorbed on bismuthiol-II resin was eluted effectively with 8-13M nitric acid or some thiols, such as cysteine and penicillamine. In the cases of thiols, the elution of selenium was found to be also based on the formation of selenotrisulphide, and the bismuthiol-II resin was regenerated. Satisfactory results were obtained when this resin was applied to the determination of selenium(IV) in river, estuarine or sea water samples.     

Cathodic stripping voltammetric determination of selenium(IV) at a thin-film mercury electrode in a thiocyanate-containing electrolyte

The well-known method for the determination of selenium(IV), which is based on the cathodic stripping voltammetry of copper(I) selenide, has been adapted for application at the thin-film mercury electrode on glassy carbon (TFME). Insufficient reproducibility and sensitivity have been overcome by using a 0.1 mol/L HClO₄ electrolyte solution containing 0.02 mol/L thiocyanate ions. Thiocyanate ions have been found to increase the peak height of the selenium response and shift it to more positive potentials. This behaviour is explained by an adsorption of SCN^– at the interface glassy carbon/Cu₂Se and its action as an electron transfer catalyst between glassy carbon and copper(I) selenide. A 3σ-detection limit of 75 ng/L Se^(IV) has been achieved. The relative standard deviation is 5.2% at 5 μg/L selenium(IV). The influence of cadmium(II), arsenic(III), zinc(II), iron(III) and lead(II) ions on the selenium response has been studied. In case of lead ions, a new signal occurred at more negative potentials than the reduction of Cu₂Se. This signal, which is probably due to the reduction of PbSe, can also be used for the determination of selenium(IV). Received: 13 November 1996 / Revised: 19 December 1996 / Accepted: 24 December 1996     

Spectrophotometric determination of trace amounts of selenium with catalytic reduction of bromate by hydrazine in hydrochloric acid media

A method is presented for the determination of selenium, based on the catalytic effect of selenium(IV) on the reduction reaction of BrO(-)(3) by N(2)H(4).2HCl. The decolourization of Methyl Orange by the reaction products was used to monitor the reaction spectrophotometrically at 525 nm. This method is precise, highly sensitive, simple, rapid, widely applicable and selective for the determination of selenium(IV) and total selenium. The variables which affected the reaction rate were fully investigated and the optimum conditions were established. Selenium, as low as 1 ng/ml, can be determined by this method. The relative standard deviation of 20 ng of selenium was 0.94% (N = 10). The method was applied to the determination of Se(IV) in a health-care product.     

Organic and inorganic selenium speciation in environmental and biological samples by nanometer-sized materials packed dual-column separation/preconcentration on-line coupled with ICP-MS

A novel, fast, and cheap nonchromatographic method for direct speciation of dissolved inorganic and organic selenium species in environmental and biological samples was developed by flow injection (FI) dual-column preconcentration/separation on-line coupled with ICP-MS determination. In the developed technique, the first column packed with nanometer-sized Al(2)O(3) could selectively adsorb the inorganic selenium [Se(IV), Se(VI)], and the retained inorganic selenium could be eluted by 0.2 mol l(-1) NaOH, while the organic Se [selenocystine (SeCys(2)) and selenomethionine (Se-Met)] was not retained. On the other hand, the second column packed with mesoporous TiO(2) chemically modified by dimercaptosuccinic acid (DMSA) could selectively adsorb Se(IV) and SeCys(2) and barely adsorb Se(VI) and Se-Met. When the sample solution was passed through the column 1, separation of inorganic selenium and organic selenium could be achieved first. Then, the effluent from column 1 was successively introduced into the column 2 and the speciation of organic selenium could be attained due to the different adsorption behaviors of Se-Met and SeCys(2) on DMSA modified TiO(2). After that, the eluent from column 1 contained Se(IV), and Se(VI) was adjusted to desired pH and injected into column 2, and the speciation of Se(IV) and Se(VI) could also be realized thanks to their different retention on column 2. The parameters affecting the separation were investigated systematically and the optimal separation conditions were established. The detection limits obtained for Se(IV), Se(VI), Se-Met and SeCys(2) were 45-210 ng l(-1) with precisions of 3.6-9.7%. The proposed method has been successfully applied for the speciation of dissolved inorganic and organic selenium in environmental and biological samples. In order to validate the methodology, the developed method was also applied to the speciation of selenium in certified reference material of SELM-1 yeast, and the determined values were in good agreement with the certified values.     

Extraction spectrophotometric determination of selenium(IV) with J acid in environmental samples

A new simple and sensitive method for the extraction and spectrophotometric determination of selenium(IV) is described. Selenium(IV) is reacted with J acid (6-ANSA) to form a butanol extractable complex with maximum absorbance of 520 nm. Beer's law is obeyed in the range of 0.03-0.3 mg/l. of selenium. Molar absorptivity and Sandell's sensitivity are found to be 18.5 +/- (0.1) x 10(3) l. mol(-1). cm(-1) and 0.004 microg/cm(2), respectively. The analytical parameters were optimized and the method applied for the determination of selenium in polluted water, soil, dust, hair and plant materials. The method is compared with other reported methods and found to be superior to many of the reported methods.     

Coprecipitative Preconcentration and Differential Pulse Cathodic Stripping Voltammetric Determination of Selenium (IV)

Abstract

A DPCSV procedure for the determination of selenium (IV) with a prior preconcentrative coprecipitation on iron (III) hydroxide has been developed. The experimental conditions for coprecipitation of selenium (IV) onto iron (III) hydroxide, viz. pH, iron (III) concentration, volume of aqueous phase and selenium concentration, were optimized. The coprecipitated selenium (IV) is dissolved in 10 ml of 0.1 M HCl and analysed using DPCSV in the presence of copper (II). Selenium concentrations as low as 10–100 ng present in 500 ml of the aqueous phase could be determined. The method is precise and has been applied to the analysis of sea water and reference material samples.     

Ultraviolet Spectrophotometric Determination of Selenium by 1-Pyrrolidinecarbodithioate Method

Abstract

An ultraviolet spectrophotometric method for the determination of selenium has been developed using ammonium 1-pyrrolidinecarbo-dithioate. The selenium(IV)-1-pyrrolidinecarbodithioate complex is extracted with chloroform and the absorbance of the extract measured at 303 mμ. Conformity to Beer's law was found for 0.5 to 9 ppm of selenium.     

Catalytic polarographic determination of total selenium in tea leaves

The catalytic polarographic determination of selenium(IV) by use of the SeSO(2-)(3) -KIO(3) system is sensitive, accurate, rapid and requires only small quantities of sample. The detection limit for selenium(IV) is 0.04 ng/ml in the final solution. The working range of the calibration is 0.04-2.5 ng/ml. Se(VI) present can be reduced with hot hydrochloric acid to Se(IV), allowing determination of the total selenium.     

Differential determination of selenium(IV) and selenium(VI) with sodium diethyldithiocarbamate, ammonium pyrrolidinedithiocarbamate and dithizone by atomic-absorption spectrophotometry with a carbon-tube atomizer

The extraction behaviour of selenium(IV) and selenium(VI) with sodium diethyldithiocarbamate, ammonium pyrrolidinedithiocarbamate and dithizone in organic solvents has been investigated by means of flameless atomic-absorption spectrophotometry with a carbon-tube atomizer. The selective extraction of selenium(IV) and differential determination of selenium(IV) and selenium(VI) have been developed. With sodium diethyldithiocarbamate and carbon tetrachloride, when the aqueous phase/organic solvent volume ratio is 5 and the injection volume in the carbon tube is 20 microl, the sensitivity for selenium is 0.4 ng/ml for 1% absorption. The relative standard deviations are ca. 3%. Interference by many metal ions can he prevented by masking with EDTA. The proposed methods have been applied satisfactorily to determination of Se(IV) and Se(VI) in various types of water.     

Separation and determination of selenium in rocks, marine sediments and plankton by direct evolution with the bromide-condensed phosphoric acid reagent

A new method is presented for the quantitative separation and determination of selenium by direct evolution with the bromide-condensed phosphoric acid reagent (Br(-)-CPA) from rocks, marine sediments and plankton. In the reaction with the Br(-1)-CPA, selenium(IV) and (VI) in the solid samples are evolved as selenium tetrabromide, and can be collected in an absorbing solution of 0.3M hydrochloric acid and 06M perchloric add (1:1), and then determined spectrophotometrically with 4-substituted o-phenylenediamines followed by the extraction of the resulting 5-substituted piazselenol into toluene. Elemental selenium and selenide do not react with the Br(-)-CPA, but can be determined after oxidation to selenite with potassium iodate. Therefore, successive distillations, the first with Br(-)-CPA and the second with IO(3)(-)-Br(-)-CPA, give a satisfactory means of diflerential determination of selenium(IV) and (VI), and elemental selenium and selenide. This method can be successfully applied for the separation of selenium in the neutron-activation analysis of standard rock samples, marine sediments and plankton, giving good and reliable results.