首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 828 毫秒
1.
Two different biodegradable latex polymers functionalised by hydroxy (1) or gluconamide (2) groups proved to be good immobilisation matrixes for glucose oxidase. The responses of these biosensors to glucose additions were measured by potentiostating the modified electrodes at 0.6 V/SCE in order to oxidise the hydrogen peroxide generated by the enzymatic oxidation of glucose in the presence of oxygen. The response of such electrodes was evaluated as a function of film thickness, pH and temperature. Rotating disk electrode experiments showed the influence of the enzyme on the structure of both latex films, namely a marked improvement in matrix permeability. The high permeability of the latex 1 based enzyme sensor (bilayer, P(m)=8.10x10(-4) cm s(-1)) resulted in a high dynamic range. Furthermore, the activation energy for a latex 1 sensor was determined to be 44.55 and 18.03 kJ mol(-1), respectively depending on the conformation of the enzyme.  相似文献   

2.
《Electrophoresis》2018,39(16):2131-2135
An electrochemical sensor for the detection of glucose using thread‐based electrodes and fabric is described. This device is relatively simple to fabricate and can be used for multiple readings after washing with ethanol. The fabrication of the chip consisted of two steps. First, three thread‐based electrodes (reference, working, and counter) were fabricated by painting pieces of nylon thread with either layered silver ink and carbon ink or silver/silver chloride ink. The threads were then woven into a fabric chip with a beeswax barrier molded around the edges in order to prevent leaks from the tested solutions. A thread‐based working electrode consisting of one layer of silver underneath two layers of carbon was selected to fabricate the final sensor system. Using the chip, a PBS solution containing glucose oxidase (GOx) (10 mg/mL), potassium ferricyanide (K3[Fe(CN)6]) (10 mg/mL) as mediator, and different concentrations of glucose (0‐25 mM), was measured by cyclic voltammetry (CV). It was found that the current output from the oxidation of glucose was proportional to the glucose concentrations. This thread‐based electrode system is a viable sensor platform for detecting glucose in the physiological range.  相似文献   

3.
A feasible method to fabricate glucose biosensor was developed by covalent attachment of glucose oxidase (GOx) to a gold nanoparticle monolayer modified Au electrode. Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) of ferrocyanide followed and confirmed the assemble process of biosensor, and indicated that the gold nanoparticles in the biosensing interface efficiently improved the electron transfer between analyte and electrode surface. CV performed in the presence of excess glucose and artificial redox mediator, ferrocenemethanol, allowed to quantify the surface concentration of electrically wired enzyme (Gamma(E)(0)) on the basis of kinetic models reported in literature. The Gamma(E)(0) on proposed electrode was high to 4.1 x 10(-12) mol.cm(-2), which was more than four times of that on electrode direct immobilization of enzyme by cystamine without intermediate layer of gold nanoparticles and 2.4 times of a saturated monolayer of GOx on electrode surface. The analytical performance of this biosensor was investigated by amperometry. The sensor provided a linear response to glucose over the concentration range of 2.0 x 10(-5)-5.7 x 10(-3) M with a sensitivity of 8.8 microA.mM(-1).cm(-2) and a detection limit of 8.2 microM. The apparent Michaelis-Menten constant (K(m)(app)) for the sensor was found to be 4.3 mM. In addition, the sensor has good reproducibility, and can remain stable over 30 days.  相似文献   

4.
A carbon nanotube paste (CNTP) electrode and a carbon nanotube paste/glucose oxidase (CNTP/GOx) electrode were prepared, and the electrochemiluminescent (ECL) behavior of luminol in the presence of glucose was investigated in detail at each of these electrodes. Compared to the classical carbon paste (CP) electrode, the CNTP electrode incorporating glucose oxidase greatly enhanced the response of the ECL sensor to glucose due to the electrocatalytic activity of the carbon nanotubes, the specificity of the enzymatic reaction, and the sensitivity of the luminol ECL reaction. Under optimal conditions, the electrode was found to respond linearly to glucose in the concentration range 1.0x10(-6) approximately 2.0x10(-3) mol/L, and the detection limit (defined as the concentration that can be detected at a signal-to-noise ratio of 3) was found to be a glucose concentration of 5.0x10(-7) mol/L. The method used to prepare the CNTP/GOx electrode was very convenient, and the electrode surface could be renewed in the case of fouling by simply polishing or cutting it to expose a new and fully active surface. The relative standard deviations (RSD) were found to be 6.8% and 8.9% for the CNTP electrode and the CNTP/GOx electrode (n=6). The electrode retained 95% of its initial response after two weeks.  相似文献   

5.
《Analytical letters》2012,45(19-20):1973-1986
Abstract

A very small glucose sensor has been realized, which consists of a gold working electrode with a glucose oxidase immobilized membrane on it, and a gold counter electrode, all made on a sapphire substrate. By using the pH sensitive ISFET as a reference electrode, the potential for a solution, whose pH is constant, can be measured and irreversible metal electrodes, such as gold or platinum, can be used as working electrode and counter electrode. The sensor is very suitable for miniaturizing and mass production, because the Integrated Circuit (IC) fabrication process can be applied. The glucose oxidase immobilized membrane was also deposited by a lift off method, one of the IC processes. A glucose concentration, from 1 to 100 mg/dl, was measured with good linear current output.  相似文献   

6.
Yang H  Kang SK  Choi CA  Kim H  Shin DH  Kim YS  Kim YT 《Lab on a chip》2004,4(1):42-46
In this paper we argue for the use of iridium oxide (IrO(x)) electrodes as quasi-reference electrodes in microfabricated biosensors and biochips that operate in buffered solutions. The simple microfabrication of these electrodes consists of a one-step electrodeposition of IrO(x) onto a microfabricated platinum (Pt) electrode. The IrO(x) electrode potential was found to vary less than 20 mV over 9 days after stabilization for 1 day in a phosphate-buffered saline (PBS) solution; this behavior of the electrode potential was found to be easily reproduced. Moreover, the electrode potential was found to vary by less than 15 mV in the initial hour of its use; this behavior of the electrode potential was also found to be reproducible. The performance of a microfabricated glucose sensor employing an IrO(x) reference electrode is characterized in this paper in order to evaluate the usefulness of this new IrO(x) electrode as a quasi-reference electrode. The glucose sensor consists of a recessed microfabricated Pt electrode array, an electrodeposited IrO(x) film, an inner layer composed of an electropolymerized poly(m-phenylenediamine)/glucose oxidase (PMPD/GOx) film, and an outer or protective layer composed of Teflon and polyurethane (PU) films. The response of this sensor was found to be equivalent to the response of the same sensor employing a commercial Ag/AgCl reference electrode. These results show that a microfabricated IrO(x) electrode can be used as a quasi-reference electrode in microfabricated biosensors and biochips operating in buffered solutions.  相似文献   

7.
A biocompatible needle-type glucose sensor with a 3-electrode configuration was constructed. A platinum-electroplated carbon stick was used as the working electrode, Ag/AgCl as the reference electrode, and a disposable hypodermic needle made of stainless steel as the counter electrode. A Nafion membrane, an immobilized glucose oxidase (GOD) membrane, and a biocompatible membrane with diffusion-limiting effect were coated successively onto the working electrode. The sensor showed a rapid response (< 120 s in batch operation), good reproducibility (RE < 3%), good stability (over 36 h in control serum), a wide dynamic range (5-600 mg/dL glucose), and superior biocompatibility. It was used to determine glucose in serum. The data obtained from the sensor showed good agreement with that from a clinical autoanalyzer (R > 0.95).  相似文献   

8.
A novel BOD biosensor has been fabricated from a microbial membrane on an oxygen electrode; a porous inorganic Al2O3 sol-gel matrix was used to immobilize the yeast. Use of the sensor is convenient and rapid compared with the official BOD5 method. The gelation time required to form the microorganism membrane was less than 15 min. There was linear relationship between the response (sensor current) and BOD values ranging from 10-50 mg x L(-1). The lifetime of the BOD biosensor was more than 30 days at ambient temperature.  相似文献   

9.
A method is developed for quantitative determination of glucose using electrochemical impedance spectroscopy (EIS). The method is based on immobilized glucose oxidase (GOx) on the topside of gold mercaptopropionic acid self-assembled monolayers (Au-MPA-GOx SAMs) electrode and mediation of electron transfer by parabenzoquinone (PBQ). The PBQ is reduced to hydroquinone (H(2)Q), which in turn is oxidized at Au electrode in diffusion layer. An increase in the glucose concentration results in an increase in the diffusion current density of the H(2)Q oxidation, which corresponds to a decrease in the faradaic charge transfer resistance (R(ct)) obtained from the EIS measurements. Glucose is quantified from linear variation of the sensor response (1/R(ct)) as a function of glucose concentration in solution. The method is straightforward and nondestructive. The dynamic range for determination of glucose is extended to more than two orders of magnitude. A detection limit of 15.6 microM with a sensitivity of 9.66 x 10(-7) Omega(-1)mM(-1) is obtained.  相似文献   

10.
Grobler SR  Rechnitz GA 《Talanta》1980,27(3):283-285
A potentiometric sensor has been developed by coupling dental plaque with a flat-surface glass electrode. Selectivity of this electrode for hexoses and pentoses has been tested. The electrode responds linearly to beta-d(+)glucose, d(+)mannose, d(+)galactose and beta-d(-)fructose over a narrow concentration range between 10(-4) and 10(-3)M, but has negligible response to the other hexoses and pentoses. This "plaque" electrode, using live bacterial cells, may serve as a model for the development of other selective electrodes for carbohydrates.  相似文献   

11.
Solid-state technology and pulse electroplating were used to fabricate a glucose biosensor based on hydrogen peroxide detection. This glucose biosensor was composed of thin-film electrodes, and enzyme-immobilized and deactivated enzyme-immobilized membranes. The electrodes were fabricated by metallic film deposition. Cr and Ni adhesive layers were applied successively by vapour deposition on the thermally oxidized SiO2 isolating layer on a silicon substrate, and then the two metallic layers were patterned by the photolithographic method. Subsequently, a 1 μm thick Au layer was applied by means of pulse electroplating, forming two anodes and one common cathode in each sensor chip. On one anode, glucose oxidase (GOD) was immobilized by cross-linking with bovin serum albumin and glutaraldehyde. A deactivated GOD-immobilized membrane was formed on the other anode, which worked as a reference working electrode. A novel differential measurement system was used to treat the output signals of the two anodes by adjusting the initial position of the response curves, compensating amplifications of the individual IV converters and treating the output signals with a subtraction circuit in order to decrease measurement error. The test results showed that the signal of ascorbic acid up to 4.5 mmol 1−1 or uric acid up to 1.2 mmol 1−1 was successfully cancelled. Glucose concentrations in the range 0.02–4.0 mmol/1 could be detected and an excellent linear response was obtained in the low concentration range. The correlation coefficient between the result of the enzyme electrode and the clinically enzymatic method for glucose measurement in human serum was 0.9912. Correlated results between the biosensor method and the routine clinical method for the measurement of glucose concentration in urine were obtained. The lifetime of the enzyme electrode was over 2 months.  相似文献   

12.
A glucose sensor was developed by electrocopolymerization using pyrroles containing a tris-bipyridine (bpy) osmium complex (Os-py), pyrrole (py), pyrrole propanoic acid (PPA) and glucose oxidase (GOx) to improve the key performance characteristics, such as the sensitivity, selectivity, and long-term stability. Tris-bipyridine osmium pyrrole complexes with four different methylene moieties were utilized to correlate the methylene length with the glucose sensor performance. The electrocatalytic response of glucose was clearly observed at electrodes modified with Os-py, except for the electrode immobilized with the Os-py complex containing the shortest methylene moiety. The current response to glucose increased up to a concentration of 100 mmol dm(-3). The electrocatalytic response to glucose at the [Os(bpy)(2)(py(6)-bpy)](2+/3+)/py/PPA/GOx electrode was stable for more than 100 days. Dissolved oxygen and potential interference compounds (ascorbic acid, uric acid, and acetaminophen) minimally perturbed the current response to glucose at the [Os(DM-bpy)(2)(py(6)-bpy)](2+/3+)/py/PPA/GOx electrode. Based on these results, a longer methylene moiety appears to improve the performance characteristics of a glucose sensor fabricated via the electropolymerization of tris-bipyridine osmium pyrrole complexes.  相似文献   

13.
A carbon-paste chemically modified with glucose oxidase and a ferrocene-containing siloxane polymer was further modified by coating the electrode surface with a poly(ester-sulfonic acid) cation-exchanger, Eastman AQ-29D. The polymer is obtained as a homogeneous aqueous dispersion at pH 5–6; when dried, the polymer coating is not water-soluble. The coating was shown not to be detrimental to the enzyme activity but to prevent electrochemically active anionic interferents such as ascorbate and urate from reaching the electrode surface. The polymer coating also prevented glucose oxidase from leaking out of the carbon paste into the contacting solution and protected the electrode surface from fouling agents present in urine and bovine serum albumin. Uncoated electrodes lost some 10-2-15% of their original response to glucose after storage in buffer for three weeks whereas the response of the coated electrodes remained constant. Calibration curves for glucose were strictly linear up to about 5 mM for uncoated and up to 20 mM for coated electrodes. The response current to glucose was not decreased after coating.  相似文献   

14.
A new concept is described for monitoring a biomolecule with a sensor having an enzyme entrapped in a conducting polymer. This is based on the sensitivity of the electroactive polymer itself to changes of pH in solution. The concept has been investigated for a glucose sensor with glucose oxidase (GOD) immobilized in a polypyrrole (PPy) layer on an inert platinum electrode. Measurements with a Pt/PPy/GOD electrode for glucose concentrations in the physiological range gave a linear correlation with logarithm of concentration over one decade with a satisfactory dynamic response. There was practically no change of slope or range of linear response to glucose after several days of use; this was in contrast to the amperometric response of the detector when there was about a 50% loss of sensitivity.  相似文献   

15.
A glucose sensor is prepared by adsorption of the mediator Meldola blue (N,N-dimethyl-7-amino-1,2-benzophenoxazinium ion, as well as glucose dehydrogenase, on the surface of a carbon electrode. The nicotinamide coenzyme, whhich is present in the solution, is reduced in the enzymatic reaction and is re-oxidized amperometrically at 0 mV vs. Ag/AgCl. The properties of such electrodes depend on whether the mediator or the enzyme is adsorbed first; possible models for the molecular arrangements at the surface are discussed. The modified electrode is mounted in a flow-through cell in a flow-injection system and tested with 50-μl injections of β-d-glucose. The calibration graphs were linear in the range 5 × 10?6—2 × 10?3 M βd glucose with the highest sensitivity at pH 6.0. The membrane-free enzyme electrode has a fast response; peak widths are 12 s at half height (flow rate 0.7 ml min?1, making it possible to process 100 samples h?1.  相似文献   

16.
Amperometric glucose sensors were prepared by electropolymerization of a pyrrole derivative having the positively charged group, 3-(1-pyrrolyl)propyltrimethylammonium bromide, in the presence of glucose oxidase on bare and Nafion-coated platinum electrodes. Linear relationships between the glucose concentration and the response current for the electrode with and without Nafion inner film were up to 10.0 and 6.0 mmol dm−3, respectively. The introduction of Nafion inner film lowered the influence of electroactive compounds, such as ascorbic acid, uric acid, and acetoaminophen, on the sensor response, but was not able to eliminate the influence of these compounds sufficiently. However, Nafion inner film was effective in increasing the electrode stability. The response current of the electrode with Nafion film remained stable for more than 50 days, while that without Nafion film was significantly reduced after 20 days of use.  相似文献   

17.
Semiconductor fabrication technology was used for development of ion sensitive field effect transistor (ISFET) and micro-electrodes which have been utilized as transducers of enzyme-based microbiosensors. A urea sensor consisted of two ISFETs; one ISFET is urease-coated ISFET and the other ISFET is reference ISFET. A linear relationship was obtained between the initial rate of voltage change and the logarithm of urea concentration over the range 1.3 to 16.7 mM. ATP and hypoxanthine sensors were also developed utilizing ISFET as a transducer. Furthermore, microelectrodes such as hydrogen peroxide and oxygen sensors were prepared by the silicone fabrication technology. A glucose sensor consisted of a hydrogen peroxide electrode and immobilized glucose oxidase membrane. A linear relationship was observed between the current increase and the concentration of glucose (1–100 mg dl−1). A microoxygen electrode was constructed from Au electrodes, polymer matrix containing alkaline electrolyte and a photocross-linkable polymer membrane. This electrode was used as a transducer in microglucose sensor. A microglutamic acid sensor is also described.  相似文献   

18.
A novel glucose biosensor is presented as that based on a glassy carbon electrode modified with hollow gold nanoparticles (HGNs) and glucose oxidase. The sensor exhibits a better differential pulse voltammetric response towards glucose than the one based on conventional gold nanoparticles of the same size. This is attributed to the good biological conductivity and biocompatibility of HGNs. Under the optimal conditions, the sensor displays a linear range from 2.0?×?10?6 to 4.6?×?10?5?M of glucose, with a detection limit of 1.6?×?10?6?M (S/N?=?3). Good reproducibility, stability and no interference make this biosensor applicable to the determination of glucose in samples such as sports drinks.
Figure
A novel glucose biosensor was prepared based on glucose oxidase, hollow gold nanoparticles and chitosan modified glassy carbon electrode. The electrode showed a good response for the glucose. The sensor has been verified by the determination of glucose in sport drink  相似文献   

19.
Xia Chu  Daxue Duan  Guoli Shen  Ruqin Yu 《Talanta》2007,71(5):2040-2047
A new amperometric biosensor for glucose was developed based on adsorption of glucose oxidase (GOx) at the gold and platinum nanoparticles-modified carbon nanotube (CNT) electrode. CNTs were covalently immobilized on gold electrode via carbodiimide chemistry by forming amide linkages between carboxylic acid groups on the CNTs and amine residues of cysteamine self-assembled monolayer (SAM). The fabricated GOx/Aunano/Ptnano/CNT electrode was covered with a thin layer of Nafion to avoid the loss of GOx in determination and to improve the anti-interferent ability. The immobilization of CNTs on the gold electrode was characterized by quartz crystal microbalance technique. The morphologies of the CNT/gold and Ptnano/CNT/gold electrodes have been investigated by scanning electron microscopy (SEM), and the electrochemical performance of the gold, CNT/gold, Ptnano/gold and Ptnano/CNT/gold electrodes has also been studied by amperometric method. In addition, effects of electrodeposition time of Pt nanoparticles, pH value, applied potential and electroactive interferents on the amperometric response of the sensor were discussed.

The enzyme electrode exhibited excellent electrocatalytic activity and rapid response for glucose in the absence of a mediator. The linear range was from 0.5 to 17.5 mM with correction coefficient of 0.996. The biosensor had good reproducibility and stability for the determination of glucose.  相似文献   


20.
A cyclic voltammetric study of the oxidation of glucose on an electrochemically formed platinum oxide layer of a platinum electrode was carried out in both the absence and presence of an underpotential-deposited thallium or lead layer. An enhanced effect on the oxidation of glucose was observed in oxide-covered platinum electrodes compared to bare platinum electrodes. This enhancement remained in the presence of an underpotential-deposited thallium or lead layer. The presence of the underpotential-deposited metal layer significantly increased the anodic peak current and the response to changes in glucose concentration over the concentration range of 0 to 10800 mg/100 cm3 (0 to 0.6 M). The presence of the underpotential-deposited thallium layer appears to alter the mechanisms of the electrochemical oxidation of glucose on the platinum electrode. This is reflected by the results-the anodic peak current is directly proportional to the voltage scan rate applied in the cyclic voltammetric study on a bare platinum electrode, whereas it is directly proportional to the square root of the voltage scan rate in the presence of an underpotential-deposited thallium layer.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号