Retention and separation of some organic water pollutants with unloaded and tri-n-octylamine loaded polyester-based polyurethane foams

The analytical utility of unloaded and polyester-based polyurethane loaded foams with tri-n-octylamine (TOA) in the removal of some phenols from water were carried out. In static mode, the TOA-loaded foams showed a good affinity of extraction towards the tested compounds as compared to the untreated foams. The various parameters affecting the retention efficiency of the tested compounds from aqueous media by the foam were examined via batch technique. The TOA-loaded foams were employed in column modes for the extraction and recovery of the tested phenols. The retention efficiency and the recovery of the tested compounds from the loaded foam column were up to 98.5%. Sorption of the compounds by the foam were brought by solvent extraction mechanism. The molecular weight and the pK(a) of the compounds play an important role in the extraction process. The height equivalent to a theoretical plate (HETP) of the TOA-foam column was found in the range 1.8-2.05 +/- 0.1 mm at flow-rates up to 10 cm(3)/min. Separation of some of the tested phenols was also carried out by the TOA-foam columns. The membrane properties of the polyester foam sorbents give unique advantages over conventional granular sorbents in rapid, versatile and effective separations and preconcentrations of the tested compounds.     

An investigation into the sorption of benzoic acids by polyurethane membrane

The extraction mechanism of organic compounds by ether- and ester-type polyurethane membrane has been investigated through a detailed study of sorption of monobromobenzoic acids. The effects of solution concentration, extraction time, surface area, pH, salts, and temperature on extraction were studied. It was found that monobromobenzoic acids are extracted in their neutral form, and that the extraction is controlled primarily by the relative strength of intra- and intermolecular hydrogen bonding. The ether-type polyurethane membrane allows a more efficient removal of monobromobenzoic acids from solution than the ester-type membrane. The extraction of benzoic acids with the ether-type membrane decreases as the temperature increases. When the ester-type polyurethane membrane is used, an extraction maximum is observed at room temperature with a decrease in extraction at lower and higher temperatures.     

Supported liquid membrane work-up in combination with liquid chromatography and electrochemical detection for the determination of chlorinated phenols in natural water samples

Summary A sample preparation method has been developed for the determination of chlorinated phenols in water. The method is based on a supported liquid membrane extraction system connected on-line to liquid chromatography with electrochemical detection. The supported liquid membrane technique utilizes a porous PTFE membrane. The membrane is impregnated with an organic solvent which forms a barrier between two aqueous phases and enables selective extraction. The technique can easily be coupled in a flow system. In this investigation five chlorinated phenols (1–5 chlorine atoms) were extracted from natural water samples. Extraction for 30 minutes resulted in detection limits of approximately 25 ng L^–1.     

Extraction of aromatic acids and phenols by polyurethane foam

The extraction of several aromatic acids and phenols including salicylic acid, 8-hydroxyquinoline, 1-amino-2-naphthol-4-sulphonic acid and cinnamic acid in the presence of various protonated alkylamines, ammonia and alkali metal cations from aqueous solution by polyurethane foam has been investigated. These compounds are extracted only in the neutral form by a solvent extraction mechanism. The mechanism has been confirmed by the salting-out effect and pH studies. With the exception of 8-hydroxyquinoline, the compounds are more extractable by polyether foam than by polyester foam, suggesting that hydrogen bonding is stronger with the polyether foam.     

Extraction of free phenols from blood by a liquid membrane enzyme reactor

The development of a liquid membrane enzyme reactor for the extraction of phenols from blood and plasma is described. Phenol permeation across the liquid membrane is studied, the transport of the toxins is linked with an enzymatic reaction. The encapsulation of the enzyme is described in detail. The stability of the multi-emulsion as well as the loss of enzyme activity during encapsulation and treatment axe examined thoroughly. The resulting liquid surfactant membrane emulsion is applied in in-vitro experiments to remove phenols from blood and plasma.     

Preconcentration and separation of some organic water pollutants with polyurethane foam and activated carbon

Summary Although pesticides and phenols, cause reproductive failure in many areas of the world, there is a no effective means of treating waste water containing these compounds. This work deals with the adsorption of insecticides and phenols from aqueous solution by untreated porous polyurethane foam and activated carbon. Static experiments showed that in comparison with activated carbon a reasonable percentage of the compounds was adsorbed by the foam. Attempts were therefore made to extract these species from aqueous solution by foam column chromatography.The results showed that the adsorption of the compounds was brought about by a mechanism similar to that of solvent extraction. The effect of various experimental conditions such as temperature, extracting medium, pH, contact time, volume of sample flow rate, compound concentration, and eluting solvents on the retention and separation of the compounds has been determined. The height equivalent to a theoretical plate (HETP) was calculated from breakthrough capacity curves and from chromatograms obtained from polyurethane foam columns for the insecticide Dyfonate; values were in the range 2.1–2.3 mm at 10–15 ml min^–1. Extraction of the compounds from natural water, and subsequent recovery, were both found to be complete. The high capacity of polyurethane provides advantages over activated carbon; in particular, large sample volumes can be analyzed at high flow rates.     

在线液膜萃取富集流动注射分光光度法测定水中挥发酚

选用无毒性的磷酸三丁酯为流动载体，煤油为膜溶剂的液膜萃取体系，建立了液膜在线萃取富集流动注射分光光度法测定水中挥发酚的新方法。对实验条件进行了优化，在最优条件下，方法的检出限为0．0007mg/L；线性范围为0．001～0．01mg/L。应用于自来水及河水中挥发酚的检测，结果满意。     

Direct determination of chlorophenols present in liquid samples by using a supported liquid membrane coupled in-line with capillary electrophoresis equipment

Actually there is a great trend on the development of effective analytical methods for monitoring trace levels of various phenols which can indicate, among others compounds, the water quality. A simple, inexpensive supported liquid membrane (SLM) device was used in combination with commercially available capillary electrophoresis (CE) equipment for the direct determination of chlorophenols in surface water samples. The manifold was used simultaneously to extract and preconcentrate the analytes from liquid samples. In the extraction set-up, the donor phase (4 mL) was placed in the CE vial, where a micro-membrane extraction unit (MMEU) accommodating the acceptor phase (100 μL) in its lumen was immersed. The supported liquid membrane was constructed by impregnating a porous Fluoropore Teflon (PTFE) membrane with a water-immiscible organic solvent (dihexyl ether). The extraction process was optimized with regard to the pH of the donor and acceptor phases, membrane liquid, extraction time and voltage applied to the inlet or outlet vial during extraction. The chlorinated phenols pentachlorophenol (PCP), 2,3,6 trichlorophenol (TCP) and 2,6 dichlorophenol (DCP) were thus efficiently separated by CE, using tris(hydroxymethyl)aminomethane (Tris) and an NaH₂PO₄ solution containing 1% (v/v) methanol at pH 10.5 as running buffer.     

Liquid–solid disk extraction followed by supercritical fluid elution and gas chromatography of phenols from water

A method combining the techniques of liquid – solid disk extraction (LSDE) and supercritical fluid elution (SFE) has been developed for the phenols regulated by the Clean Water Act. LSDE uses a disk or membrane made of polytetrafluoroethylene (PTFE) fibrils impregnated with small particles, e.g. styrene divinylbenzene (SDB) resin, to extract phenols from water. After disk extraction the retained analytes are eluted from the disk using SFE. SFE is used as an alternative to liquid solvent elution with an organic solvent. Analytes are separated, identified, and quantified using gas chromatography – ion trap detector mass spectrometry (GC-ITDMS). The method is capable of sub parts per billion detection limits, and precision of 5–28% RSD. Evaluation of various disks or membranes, such as C₁₈-silica disks, SDB disks, and ion exchange membranes, has also been performed for the extraction of phenols from water. The results obtained from the in-situ aqueous acetylation of phenols and extraction of their acetates are quantitative. The utilization of LSDE and SFE techniques has proven to be a more effective approach than liquid – liquid extraction in minimizing air pollution and solvent waste.     

The distribution coefficients of phenol and substituted phenols in the ammonium sulfate-poly-N-vinylpyrrolidone-water system

The extraction of phenols from water-salt solutions was performed using a water-soluble polymer (poly-N-vinylpyrrolidone). The distribution coefficients, the degree of extraction of 13 phenols, and interrelation between the extraction characteristics and structure of distributed compounds were determined. The conditions of the process were optimized to provide maximum extraction of phenols by poly-N-vinylpyrrolidone from water-salt solutions.     

Ionic liquid based three-phase liquid-liquid-liquid solvent bar microextraction for the determination of phenols in seawater samples

For the first time, an ionic liquid based three-phase liquid-liquid-liquid solvent bar microextraction (IL-LLL-SBME) was developed for the analysis of phenols in seawater samples. The ionic liquid, 1-butyl-3-methylimidazolium hexafluorophosphate ([BMIM][PF(6)]), was used as the intermediary solvent for LLL-SBME, enhancing the extraction efficiency for polar analytes. In the procedure, the analytes were extracted from the aqueous sample into the ionic liquid intermediary and finally, back-extracted into an aqueous acceptor solution in the lumen of the hollow fiber. The porous polypropylene membrane acted as a filter to prevent potential interfering materials from being extracted, and no additional cleanup was required. After extraction, the acceptor solution could be directly injected into a high-performance liquid chromatographic system for analysis. Six phenols, 2-nitrophenol, 4-chlorophenol, 2,3-dichlorophenol, 2,4-dichlorophenol, 2,4,6-trichlorophenol and pentachlorophenol were selected here as model compounds for developing and evaluating the method. The most influential extraction parameters were evaluated, including the ionic liquid, the composition of donor solution and acceptor solution, the extraction time and the extraction temperature, the effect of ionic strength, and the agitation speed. Under the most favorable extraction parameters, the method showed good linearity (from 0.05-50 to 0.5-50 μg/L, depending on the analytes) and repeatability of extractions (RSD below 8.3%, n=5). The proposed method was compared to conventional three-phase LLL-SBME and ionic liquid supported hollow fiber protected three-phase liquid-liquid-liquid microextraction, and showed higher extraction efficiency. The proposed method was demonstrated to be a simple, fast, and efficient method for the analysis of phenols from environmental water samples.     

Determination of phenols in water by on-line solid-phase disk extraction and liquid chromatography with electrochemical detection

Poly(styrene-divinylbenzene) (PS-DVB) membrane extraction disks were used as sorbents for the on-line solid phase extraction of 13 phenols (nitro and chlorophenols) in river and tap waters. Determination was performed by liquid chromatography with electrochemical detection (LC-ED). An acetate buffer-acetonitrile-methanol mixture as mobile phase and amperometric detection at +1100 mV were used. High water volumes, up to 250 ml, can be preconcentrated without loss of phenols (recoveries between 80% and 100%) except for the more polar ones. Moreover, detection limits between 0.01 and 0.1 μg l⁻¹ in tap water and between 0.1 and 1.0 μg⁻¹ in river water were obtained. The method has been applied to the analysis of two river water samples.     

SPME-GC联用测定环境水样中的酚类化合物

建立了固相微萃取与气相色谱联用技术测定环境水样中酚类化合物的方法. 探讨了pH、离子强度、萃取头类型、萃取时间以及解析时间等条件对酚类化合物萃取量的影响, 优化了GC仪器条件. 在优化的条件下, 酚类化合物的响应值与浓度有良好的线性关系, 线性范围为0.20～200 μg/L, 检出限在0.019～0.10 μg/L之间, 相对标准偏差(RSD, n=5)为4.4%～11%, 水样平均加标回收率为92.2%～101.9%, 所建立的方法可测定环境水样中的酚类化合物.     

Effect of moisture on supercritical fluid extraction of polynuclear aromatic hydrocarbons and phenols from soil using an automated extractor

An automated supercritical fluid extraction system was evaluated with polynuclear aromatic hydrocarbons and phenols to demonstrate extraction efficiency, collection efficiency, and sample cross contamination. Results showed that 75/25 glass beads/octadecyl silica provided the highest collection efficiency for these classes of compounds. Also, the automated SFE system was used to study the effect of different percentages of water (w/w) in soil on extraction efficiency of fortified PAH and phenols at different temperatures and pressures. Results showed that the presence of (available) water in soil (>10%) does, increase extraction efficiency of higher molecular weight PAH at higher temperature. Also it was demonstrated that temperature rather than pressure had a marked effect on extraction efficiency. The extraction efficiency of phenols from soil which contained 5% of water, using pure supercritical CO₂, was higher than those obtained from dry soil or soil containing 1 % water. Extraction of phenols from soil did not show a dependence on pressure or temperature.     

固相萃取/高效液相色谱法测定茶油中的多种天然酚类物质

建立了同时分离、检测茶油中23种酚类物质的高效液相色谱方法.比较了液液萃取、固相萃取两种方法的提取效果,并优化了流动相、检测波长、进样量等参数.23种酚类物质在优化条件下均可有效分离,并在0.059～9.115μg/g范围内具有良好的线性关系,相关系数为0.9776～1.0000,检出限为0.041～0.379μg/g...     

The separation and isolation of gold by selective extraction and transport through a polyurethane ether-type membrane

The separation and isolation of gold(III) by selective extraction and transport through a ether-type polyurethane membrane was studied. Gold was found to be extracted into the membrane in strongly acidic solutions of HCl and HBr as the HAuBr(4) and HAuCl(4) complexes. Once extracted, the HAuCl(4) and HAuBr(4) complexes diffuse through the membrane and are recovered quantitatively in a receiving cell solution. This phenomenon was studied for the separation of a variety of binary metal solutions as well as for the separation of gold from a solution of gold ore. The preconcentration of gold was also achieved by adjusting the starting and receiving cell solution volumes.     

Static–dynamic sequential superheated liquid extraction of phenols and fatty acids from alperujo

Superheated liquids of different polarity have been used for sequential extraction of fatty acids and phenols from alperujo. Multivariate methodology has been used to optimise the static–dynamic extraction. Forty-two minutes are required to complete extraction (20 mg/kg of fatty acids and up to 2,200 mg/kg of hydroxytyrosol in the raw material used). The efficacy of the extraction has been demonstrated and compared with that of conventional methods (Folch and stirring-based methods for fatty acids and phenols, respectively), which needed 4.5 and 24 h for the extraction of fatty acids and phenols, respectively. The non-polar and polar extracts were injected into GC–MS and HPLC–MS–MS equipment, respectively, for individual separation–quantification of the target compounds. The simplicity of the experimental setup and the low costs of the raw material make the proposed method advisable when extraction of both fractions is required.     

地质环境样品中挥发酚分析现状与进展

挥发酚被列为环境优先控制的有机污染物,已成为评价环境污染的重要指标之一。该文简述了挥发酚的化学性质及地质环境来源,概括了国内外挥发酚测定的相关标准方法,从样品预处理技术和检测技术两方面综述了近年来地质环境样品中挥发酚分析的研究现状。重点对溶剂萃取、蒸馏、固相萃取、固相微萃取和吹扫捕集等样品预处理技术,以及4-氨基安替比林分光光度法、紫外和荧光分光光度法、溴化容量法、气相色谱法、液相色谱法和酚生物传感器法等技术在地质环境样品中挥发酚分析上的应用进行了较为全面的总结,并对其未来的发展趋势进行了展望,为进一步研究挥发酚的分析技术及其环境应用提供参考。     

PMBP-loaded polyurethane foam as an extractant for thorium nitrate from aqueous solution

A study on extraction of thorium with 1-phenyl-3-methyl-4-benzoyl-pyrazolone-5 (PMBP)-loaded polyurethane foam is described. Open-cell polyurethane foam has proved to be effective as supporting material for PMBP. Thorium nitrate can be quantitatively extracted by PMBP-loaded polyurethane foam over a wide pH range. The effect of equilibrium time, pH, thorium concentration, various anions and flow-rate on the extraction efficiency of thorium is examined. A technique of extraction chromatography column with PMBP foam cylinder has been developed for trace thorium analysis of bulky water samples.     

Isolation and bioactivities of organic acids and phenols from walnut shell pyroligneous acid

Based on differences in acidity, organic acids and phenols were enriched by pH gradient extraction method from walnut shell pyroligneous acid. Contents of organic acids and phenols were measured by acid-base titration method and Folin colorimetric assay, respectively to assess the effectiveness of the extraction. In addition, the antimicrobial activity of the organic acids and antioxidant activity of phenols extracted were investigated. Chemical components of the extracts that were from the optimal concentrations of NaHCO₃ and NaOH were measured by GC-MS. The results showed that 5% NaHCO₃ could enrich the highest amount of organic acids, whereas 4% NaOH could enrich the highest amount of phenols. The enriched organic acids exhibited high antimicrobial activity, and the enriched phenols exhibited antioxidant activity under low concentrations, and demonstrated dosage dependency.