Poly(vinyl chloride) membrane cesium ion-selective electrodes based on lipophilic calix[6]arene tetraester derivatives

New lipophilic tetraesters of calix[6]arene and calix[6]diquinone are investigated as cesium ion-selective ionophores in poly(vinyl chloride) membrane electrodes. For an ion-selective electrode based on calix[6]arene tetraester I, the linear response is 1x10(-6)-1x10(-1) M of Cs(+) concentrations. The selectivity coefficients for cesium ion over alkali, alkaline earth and ammonium ions are determined. The detection limit (log a (Cs (+))=-6.31) and the selectivity coefficient (log k (Cs (+),Rb (+))(pot )=-1.88) are obtained for polymeric membrane electrode containing calix[6]arene tetraester I.     

Triethylene glycol ether end-grafted carbosilane dendrimer: a potential ionophore for potassium ion recognition.

The performance of a newly synthesized carbosilane dendrimer bearing four triethylene glycol ether (TEG) units, Si(CH2CH2CH2Si(Me)2CH2CH2CH2(OCH2CH2)3Me)4 (1), as ionophores in ion-selective electrodes has been investigated. Optimization of the plasticized polyvinyl chloride membrane composition has produced electrodes that exhibit a Nernstian response for potassium ions. The best general characteristics exhibited by the electrodes were found when the membrane composition ratio of DPE:1:NaTPB:PVC 60:3:2:35 (wt%) was used. The response of the electrode was linear with a Nernstian slope of 58.3 mV/decade over the K+ ion concentration range of 1.9x10(-7) to 1.0x10(-1) M with a detection limit of 3.1x10(-7) M. The response time to achieve a 95% steady potential for the K+ concentration ranging from 1.0x10(-1) to 1.0x10(-8) M was less than 10 s, and it was found that the electrode is suitable for use within a pH range of 5.5-8.5. The selectivity coefficients (log KPotK+,Mn+)), which were determined by the fixed interference method, showed good selectivity for K+ against most of the interfering cations. The influence of this selective ion-binding behavior using electrospray ionization time-of-flight (ESI-TOF) mass spectrometric studies is discussed.     

Cesium ion-selective electrodes based on 1,3-alternate thiacalix[4]biscrown-6,6

Four thiacalix[4]biscrown ethers with 1,3-alternate conformation were examined for the potentiometric responses in poly(vinyl chloride) membrane electrodes. Their potentiometric selectivities toward potassium and cesium ions over other alkali, alkaline earth, and transition metal ions were measured by the fixed interference method (FIM). Among the ionophores, 1,3-alternate thiacalix[4]biscrown-6,6 showed a high selectivity for cesium over potassium ion and so was optimized as a Cs⁺-selective electrode. The electrode exhibited a linear response with a near Nernstian slope of 57.6 mV per decade in the concentration range of 1.0×10⁻⁶ to 3.2×10⁻² M. It was suitable for use in aqueous solution in a wide range of pH 2.5-12.5 and had a fast response time of ca. 5 s. On the basis of 1,3-alternate thiacalix[4]biscrown-6,6, the electrode has a wide linear range and selectivity for cesium ion over potassium ion better than those previously reported with other ionophores.     

Mercury(II) ion-selective electrodes based on heterocyclic systems

Mercury ion-selective electrodes (ISEs) were prepared with a polymeric membrane based on heterocyclic systems: 2-methylsulfanyl-4-(4-nitro-phenyl)-l-p-tolyl-1H-imidazole (I) and 2,4-diphenyl-l-p-tolyl-1H-imidazole (II) as the ionophores. Several ISEs were conditioned and tested for the selection of common ions. The electrodes based on these ionophores showed a good potentiometric response for Hg2+ ions over a wide concentration range of 5.0 x 10(5-) - 1.0 x 10(-1)M with near-Nernstian slopes. Stable potentiometric signals were obtained within a short time period of 20 s. The detection limits, the working pH range of the electrodes were 1.0 x 10(-5) M and 1.6-4.4 respectively. The electrodes showed better selectivity for Hg2+ ions over many of the alkali, alkaline-earth and heavy metal ions. Also sharp end points were obtained when these sensors were used as indicator electrodes for the potentiometric titration of Hg2+ ions with iodide ions.     

Potentiometric determination of silver(I) by selective membrane electrode based on derivative of porphyrin.

The performance of silver metal complexes with meso-tetraphenylporphyrin ([H2T(4-CH3)]PP) as ionophores for ion-selective electrodes was studied. The electrode exhibited linear response with Nernstian slope of 59.2 +/- 1.0 mV per decade within the concentration range of 1.0 x 10(-7)-1.0 x 10(-1) M silver ions. The limit of detection as determined from the intersection of the extrapolated linear segments of the calibration plot, was 1.0 x 10(-7) M. The response time of the electrode was < 10 s over the entire concentration range. The silver-selective electrode exhibited good selectivity for Ag(I) with respect to alkali, alkaline earth and heavy metal ions. The electrodes could be used at least three months without a considerable divergence in their potential. The electrodes are suitable for use in aqueous solutions in a wide pH range of 3.0-9.0. They were used as indicator electrodes in titration of Ag(I) with sodium iodide solution and were successfully applied to direct determination of silver in real samples.     

Highly selective PVC-membrane electrodes based on Co(II)-Salen for determination of nitrite ion.

A cobalt(II) derivative was used as a suitable ionophore for the preparation of a polymeric membrane nitrite-selective electrode. The electrode reveals a Nemstian behavior over a very wide NO2- ion concentration range (1.0 x 10(-6)-1.0 x 10(-1) M) and a very low detection limit (5.0 x 10(-7) M). The potentiometric response is independent of the pH of solution in the pH range 4.0-9.5. The electrode shows advantages such as low resistance, fast response and, most importantly, good selectivity relative to a wide variety of inorganic and organic anions. In fact, the selectivity behavior of the proposed NO2- ion-selective electrode shows great improvements compared to the previously reported electrodes for nitrite ion. The proposed electrodes could be used for at least 2 months without any significant changes in potentials. The electrode was successfully applied to the determination of nitrate ion concentrations in sausage and milk samples.     

Calixazacrown ethers for copper(II) ion-selective electrode

Five novel 1,3-alternate calix[4]azacrown ethers having 2-picolyl, 3-picolyl, and benzyl unit on the nitrogen atom were synthesized and used as ionophores for transition metal-selective polymeric membrane electrodes. The electrode based on 2-picolyl armed 1,3-alternate calix [4] azacrown ether exhibited Nernstian response toward copper (II) ion over a concentration range (10(-4.5) M-10(-2.5) M). The detection limit was determined as 10(-5) M in pH 7 and the selectivity coefficients for possible interfering cations were evaluated. Anions in the sample solution strongly affected the electrode response.     

Optimization of polymeric triiodide membrane electrode based on clozapine-triiodide ion-pair using experimental design

Central composite design (CCD) and response surface methodology (RSM) were developed as experimental strategies for modeling and optimization of the influence of some variables on the performance of a new PVC membrane triiodide ion-selective electrode. This triiodide sensor is based on triiodide-clozapine ion-pair complexation. PVC, plasticizers, ion-pair amounts and pH were investigated as four variables to build a model to achieve the best Nernstian slope (59.9 mV) as response. The electrode is prepared by incorporating the ion-exchanger in PVC matrix plasticized with 2-nitrophenyl octal ether, which is directly coated on the surface of a graphite electrode. The influence of foreign ions on the electrode performance was also investigated. The optimized membranes demonstrate Nernstian response for triiodide ions over a wide linear range from 5.0 x 10(-6) to 1.0 x 10(-2)mol L(-1) with a limit of detection 2.0 x 10(-6) mol L(-1) at 25 degrees C. The electrodes could be used over a wide pH range 4-8, and have the advantages of easy to prepare, good selectivity and fast response time, long lifetime (over 3 months) and small interferences from hydrogen ion. The proposed electrode was successfully used as indicator electrode in potentiometric titration of triiodide ions and ascorbic acid.     

Cesium-ion selective electrodes based on calix[4]arene dibenzocrown ethers

Four calix[4]arene dibenzocrown ether compounds have been prepared and evaluated as Cs(+)-selective ligands in solvent polymeric membrane electrodes. The ionophores include 25,27-bis(1-propyloxy)calix[4]arene dibenzocrown-6 1, 25,27-bis(1-alkyloxy)calix[4]arene dibenzocrown-7s 2 and 3, and 25,27-bis(1-propyloxy)calix[4]arene dibenzocrown-8 4. For an ion-selective electrode (ISE) based on 1, the linear response concentration range is 1x10(-1) to 1x10(-6) M of Cs(+). Potentiometric selectivities of ISEs based on 1-4 for Cs(+) over other alkali metal cations, alkaline earth metal cations, and NH(4)(+) have been assessed. For 1-ISE, a remarkably high Cs(+)/Na(+) selectivity was observed, the selectivity coefficient (K(Cs,Na)(Pot)) being ca. 10(-5). As the size of crown ether ring is enlarged from crown-6 (1) to crown-7 (2 and 3) to crown-8 (4), the Cs(+) selectivity over other alkali metal cations, such as Na(+) and K(+), is reduced successively. Effects of membrane composition and pH in the aqueous solution upon the electrode properties are also discussed.     

Coated-wire copper(II)-selective electrode based on phenylglyoxal-α-monoxime ionophore

A copper(II) ion-selective electrode based on a recently synthesized 2-quinolyl-2-phenylglyoxal-2-oxime (phenylglyoxal-alpha-monoxime) has been developed. The PVC-based membrane containing phenylglyoxal-alpha-monoxime, dibutyl phthalate as plasticizer, and sodium tetraphenylborate as anion excluder and membrane modifier, was directly coated on the surface of a platinum-wire electrode. The response of the electrode was linear with a near-Nernstian slope of 28.2 mV decade(-1) within the Cu2+ ion concentration range 1x10(-6)-1x10(-1) mol x L(-1). The response time for the proposed electrode to achieve a 95% steady potential for Cu2+ concentrations ranging from 1x10(-1) to 1x10(-6) mol x L(-1) is between 10 and 50 s, and the electrode is suitable for use within the pH range of 3 to 6.5. The electrode has a detection limit of 5x10(-7) mol x L(-1) Cu2+ and its selectivity relative to several alkali, alkaline earth, transition, and heavy metal ions was good. The coated-wire electrode could be used for at least two months without a considerable alteration of its potential. Applications of the electrode for determination of copper in milk powder samples and as an indicator electrode for potentiometric titration of Cu2+ ion using EDTA are reported.     

Tetrabenzyl pyrophosphate as a new class of neutral carrier responsive to lead ion

Tetrabenzyl pyrophosphate and diphenylphosphinic anhydride, with two phosphoryl groups (PO) as ligating sites, can be used as novel ionophores to make Pb(2+)-selective membrane electrodes. A good result was obtained with tetrabenzyl pyrophosphate, and the electrode based on this ionophore and bis(1-butylpentyl) adipate as a solvent mediator in a poly(vinyl chloride) membrane matrix exhibited a near-Nernstian response to Pb(2+) in the concentration range of 1x10(-5)-1x10(-2) M with a slope of 28.7 mV per concentration decade in a solution containing 0.1 M Mg(NO(3))(2). The limit of detection was 3x10(-6) M. The selectivity of this electrode to other metal cations was comparable to the best case in many Pb(2+)-selective electrodes so far developed. Addition of potassium tetrakis(p-chlorophenyl)borate (40 mol% relative to tetrabenzyl pyrophosphate) caused a drastic change in the response slope (53.3 mV per concentration decade), probably due to the formation of PbA(+), where A stands for anions present in the sample solution, and decreased significantly the electrode selectivity to other metal cations.     

Novel Cesium‐Selective Electrodes Based on Lipophilic 1,3‐Bisbridged Cofacial‐calix[6]crowns

Five bisbridged calix[6]crowns have been investigated as Cs⁺ ionophore in PVC membrane electrodes. As ionophores, three 1,3‐bisbridged calix[6]crown‐4‐ethers( I–III ), 1,3‐bisbridged calix[6]crown‐5‐ether( IV ), and 1,3‐bisbridged calix[6]crown‐6‐ether( V ) have been evaluated. The membranes all give good Nernstian response in the concentration range from 1×10^?7 to 1×10^?1 M of cesium ion. The best detection limits (?log aequation/tex2gif-inf-1.gif=7.08–7.36) are obtained for electrode membranes containing 1,3‐bisbridged cofacial‐calix[6]crown‐4‐ethers( I‐III ), and the values are the lowest compared with those reported previously. The highest selectivity coefficients [ 3.74(Cs/K), 2.63(Cs/Rb)] are obtained for the membrane of 1,3‐bisbridged calix[6]crown‐4‐ether( II ), and these values are also the highest compared with previous reports for Cs⁺‐ISEs. The highest selectivity towards cesium ion is attributed to the geometrically cofacial positions of two crown‐ethers in calix[6]crowns in order to provide the complex of cesium ion and eight oxygens of cofacial crowns.     

Neutral bidentate organophosphorus compounds as novel ionophores for potentiometric membrane sensors for barium(II)

Bis(diarylphosphine oxide) naphthalene compounds are used as novel ionophores in plasticized poly(vinyl chloride) matrix membrane sensors for barium ions. The most favorable sensor was 1,2-bis(diethylphenylphosphine oxide)naphthalene containing potassium tetrakis(4-chlorophenyl)borate as lipophilic salt and o-nitrophenyloctyl ether as plasticizer for ion-selective electrode membrane construction. The electrode showed excellent properties. It gave a linear response with a Nernstian slope of 30 mV per decade within the concentration range 10(-1)-10(-5) mol L(-1) BaCl2. The electrode exhibits a high selectivity towards Ba2+ with respect to Li+, Na+, K+, Rb+, Cs+, NH4+, Ag+, Mg2+, Ca2+, Sr2+, Mn2+, Fe2+, Co2+, Ni2+, Cu2+, Zn2+, Cd2+, Pb2+, Al3+, La3+, and Ce3+ ions. The electrode response was stable over a wide pH range (3-11). The lifetime of the electrode was about 2 months. It was successfully applied to the determination of Ba2+ contents in some rocks.     

Farbstoffe durch Amin-HCN-Austauschreaktion am 2-Dicyanmethylen-1,3-indandion,I Synthesen mit Nitrilen, 32. Mitt.

Zusammenfassung 2-Dicyanmethylen-1,3-indandion setzt sich mit arom. Aminen sowie mit subst. Hydrazinen unter Austausch von HCN um. Die erhaltenen Anilino-(1,3-dioxo-2-indanyliden)acetonitrile 2a–g sind intensiv gelb-orange bis dunkelrot und besitzen potentielle Farbstoffeigenschaften.

---

Syntheses with nitriles, XXXII: Dyes obtained from 2-Dicyanomethylene-1.3-indandione by amine-HCN-exchange, I

2-Dicyanomethylene-1.3-indandione reacts with aromatic amines and subst. hydrazines, resp., while HCN is eliminated. The anilino-(1.3-dioxo-2-indanylidene)acetonitriles obtained are orange to dark-red products with properties of dyes.

---

---

Mit 2 Abbildungen

---

Herrn Prof.E. Ziegler, Graz, zum 60 Geburtstag gewidmet.     

Ion-selective electrode for aluminum determination in pharmaceutical substances, tea leaves and water samples

A novel ion-selective PVC membrane sensor for Al(III) ions based on 6-(4-nitrophenyl)-2-phenyl-4-(thiophen-2-yl)-3,5-diaza-bicyclo[3.1.0]hex-2-ene (NTDH) as a new ionophore has been prepared and studied. The electrode exhibit a good response for aluminum ion over concentration range of 1.0x10(-6) to 1.0x10(-1) mol L(-1) with a Nernstian slope of 19.6+/-0.4 mV per decade and low detection limit of 6.3x10(-7) mol L(-1). The best performance was obtained with membrane composition 30% poly(vinyl chloride), 62% acetophenone, 5% oleic acid, 3% ionophore and 2 ml tetrahydrofuran. NTDH-based electrode was suitable for aqueous solutions of pH 3. It has relatively fast response time (approximately 10 s) and can be used at least for 3 months without any considerable divergence in potentials. The proposed membrane electrode revealed good selectivity for Al(III) ions over a wide variety of other cations. The standard electrode potentials were determined at different temperatures and used to calculate the isothermal coefficient of the electrode. The formation constant and stoichiometry ratio of ionophore-Al(III) complex were calculated at 25 degrees C by using segmented sandwich membrane method. It was used in non-aqueous solvents and also as indicator electrode in potentiometric determination of Al(III) ions in some real samples.     

Spectrophotometric determination of vitamin E (alpha-tocopherol) using copper(II)-neocuproine reagent

A coated graphite-epoxy ion-selective electrode for bismuth(III), based on the ion-pair between the [Bi(EDTA)](-) anion and tricaprylylmethylammonium cation (Aliquat 336S) incorporated onto a poly(vinylchloride) (PVC) matrix is constructed. A thin membrane film of this ion-pair, dibutylphthalate (DBPh) or ortho-nitrophenyloctylether (o-NPOE) in PVC was deposited directly onto a Perspex(R) tube which contained a graphite-epoxy conductor substrate attached to the end of a glass tube. The coating solution was prepared by dissolving 30% (w/w) of PVC in 10 ml of tetrahydrofuran following addition of 65% (w/w) DBPh or o-NPOE and 5% (w/w) of the ionic pair. The effect of pH, EDTA concentration and some cation and anion on the electrode response is investigated. The bismuth(III) ion-selective electrode shows a linear response in the bismuth(III) concentration range from 1.0 x 10(-8) to 1.0 x 10(-1) mol 1(-1) and 1.0 x 10(-7) to 1.0 x 10(-1) mol 1(-1) and a slope of 56.8 and 59.2 mV dec.(-1) for the polymeric membranes containing DBPh and o-NPOE, respectively. The lifetime of this electrode was superior to 1 year (over 1600 determinations for each polymeric membrane), with practical detection limits of 6.3 x 10(-9) and 4.4 x 10(-8) mol 1(-1) with these plasticizers. Application of this electrode with bismuth(III) determination in a stomach anti-acid sample is described.     

The synthesis and membrane transport characteristics of macrocyclic polyether ligands composed of 1,10-phenanthroline as carriers for primary amine species

Four macrocyclic polyether derivatives of o-phenanthroline were synthesized and used as neutral carriers for preparing poly(vinyl chloride) (PVC) membrane electrodes to sense primary amine species. The potentiometric response characteristics of the electrodes prepared were investigated. The electrode sensitive to benzyl amine as model analyte showed a linear response range of 8.0 x 10(-6)-0.1 mol/l with a detection limit of 8.9 x 10(-7) mol/l and a slope of 56.5 mV/decade. The linear potentiometric response of the mexiletine-sensitive electrode was 4.7 x 10(-6)-0.1 mol/l, and the detection limit was 5.0 x 10(-7)1 mol/l with a slope of 59.0 mV/decade. The transfer behavior of amines and ammonium ions through an organic phase was investigated by means of the bulk liquid membrane transport experiment. The effects of pH, counter anions and other factors on the transfer of the amine and ammonium species were studied. The mass transfer rates of the test species facilitated by macrocyclic polyether derivatives of o-phenanthroline were determined and the following sequence was found: benzyl amine > ethyl amine > tetramethyl ammonium > triethyl amine > diethyl amine > K(+) > ammonium > Na(+) > Ca(2+) > Mg(2+). This was exactly the potentiometric selectivity sequence of the membrane electrodes prepared by using these carriers. The mechanism of transfer of benzyl amine through a membrane phase induced by the carriers has been elucidated on the basis of experimental observations.     

Selective electrodes for silver based on polymeric membranes containing cali

Silver ion-selective electrodes were prepared with polymeric membranes based on two calix[4]arene derivatives functionalized by two hydroxy and two benzothiazolylthioethoxy groups. The electrodes all gave a good Nernstian response of 58mV decade(-1) for silver in the activity range 5 x 10(-6)-10(-1) M, the limits of detection reached 10(-5.8) M and exhibited high selectivity towards alkali, alkaline earth and some transition metal ions. The electrode was used as indicator electrode in titrations of Ag+ with Cl- ion.     

Anion selective polymeric membrane electrodes based on cyclopalladated amine complexes

The potentiometric anion selectivity of two polymer membrane based electrodes (I and II) formulated with two new cyclopalladated amine complexes as the active components are examined. The electrodes exhibit a non-Hofmeister selectivity pattern with a significantly enhanced response towards thiocyanate, iodide and nitrite. The graph potential versus log c is linear over the concentration range 10(-6)-6x10(-2) M thiocyanate with electrode I and 10(-6)-10(-3) M with electrode II; 10(-5)-10(-2) M iodide with electrode I and 10(-3)-6x10(-2) M with electrode II; and 10(-3)-6x10(-2) M nitrite with both electrodes. The influence of the plasticizer and pH are studied. The potentiometric selectivity coefficients for I, II and blank membrane electrodes are reported. The selective interaction between Pd(II) thiocyanate, iodide and nitrite is postulated to be the reason for its higher response.     

Strontium ion-selective electrodes based on the diamides with pyridine ring as ionophores

Poly(vinyl chloride) membrane strontium ion-selective electrodes were developed by using three lipophilic diamides containing pyridine ring as ionophores. The relationship between the structure of the ionophores and the performance of these electrodes, as well as the effects of the plasticizers and additives, were investigated. The Sr(2+)-electrode based on N,N,N',N'-tetracyclohexyl-2,6-pyridine-bis(methyleneoxy acetamide) as neutral carrier, potassium tetrakis (p-chlorophenyl) borate (KTpClPB) as additive, and o-nitrophenyloctyl ether (o-NPOE) as plasticizing solvent. It exhibits excellent properties with a Nernstian slope of 29 mV/pSr(2+)and a linearity range of 2x10(-5) to 1x10(-2) M at 25 degrees C, K(Sr,Ba)(Pot)=2x10(-2).