Determination of molybdenum in steel by adsorptive stripping voltammetry in a homogeneous ternary solvent system.

A new alternative approach for the determination of molybdenum in steel is proposed, using adsorptive stripping voltammetry (AdSV). The determinations are performed in a homogeneous ternary solvent system (HTSS) composed of N,N-dimethylformamide, ethanol and water, with alpha-benzoinoxime (alpha BO) as the complexing agent and a sodium acetate-acetic acid buffer as the support electrolyte. The HTSS composition was optimized by mixture design modelling. The AdSV measurements were performed in the differential pulse mode using an accumulation potential of -1050 mV. Under these optimized experimental conditions, the Mo(VI)-alpha BO reduction current peak potential is observed at potentials near -1250 mV, much lower than those usually reported, and the calibration plot follows the polynomial equation I = 0.359 + 0.265 [CMo(VI)] - 0.015 [CMo(IV)]2 (r2 = 0.997), for Mo concentrations up to 10.0 micrograms L-1. There is a linear range in this calibration plot for Mo(VI) concentrations up to 0.20 microgram L-1, defined by the equation I = 0.353 + 0.385 [CMo(VI)] (r2 = 0.980). In both cases, I is the absolute value for the current in microA and CMo(VI) is the concentration of Mo in microgram L-1. The detection limit for this linear concentration range was estimated as 20 pg L-1. A RSD of 0.43% is associated with the signals at a Mo(VI) level of 0.72 microgram L-1. From the common method-interfering species tested, only iron at Fe/Mo(VI) ratios above 500 and vanadium and tungsten at M/Mo(VI) ratios above 100 appear to affect the analytical response significantly. Phosphorous may also reduce the analytical signal at P/Mo(VI) ratios above 100, due to the formation of the competitive P-Mo complex. The suggested routine procedure was tested by analyzing four stainless steel samples and the results compared well with the ICP-AES measurements. The higher sensitivity of this method permits direct determination of Mo(VI) in steels, eliminating the need of analyte concentration or separation steps in the sample processing procedure.     

Radiochemical solvent extraction of molybdenum/VI/ using99Mo tracer

A radiochemical solvent extraction method has been developed for the micro determination of Mo/VI/ using⁹⁹Mo tracer. It involves removal of^99mTc by ethyl methyl ketone /EMK/ and extraction of Mo with tri-n-butyl phosphate /TBP/ from 5M HCl. Different parameters affecting the extraction such as pH dependence, nature of solvent and interferences due to other radionuclides have been studied. The method can be used up to 2 g of Mo.     

Metal chelate exchange in the organic phase-I Theory: application in spectrophotometry and complex chemistry

Metal chelates, extracted from an aqueous phase by organic solvents, can react with other chelating agents (or their metal chelates) dissolved in the same solvent. This exchange of metal chelates in the organic phase can be used for (1) investigation of the exchange equilibrium and composition of the metal chelates formed, (2) determination of the extraction constants, (3) preparation of new inner-complexes soluble in organic solvents, and (4) spectrophotometric determination of small amounts of metals. The theory and experimental verification of this phenomenon are given. The extraction constants of silver and zinc diethyldithiocarbamates in carbon tetrachloride have been determined by means of the extraction constants of the corresponding dithizonates. A mixed complex of arsenic(III) with dithizone and diethyldithiocarbamic acid has been prepared and its properties studied. A simple method for spectrophotometric determination of microgram quantities of arsenic is proposed.     

Alpha-benzoinomixe: Extracting agent for uranium(VI), tungsten(VI), molybdenum(VI) and some transition metals of the iron family

The effect of pH on the percent extraction of vanadium(V), iron(II), cobalt(II), nickel(II), copper(II), molybdenum(VI), tungsten(VI) and uranium(VI) by -benzoinoxime in different solvents has been studied. The maximum recovery is not appreciably affected by the nature of the solvent, but occurs at different pH values for different metals. The pH corresponding to maximum extraction increases with increasing hydrolysis pK of the species in aqueous solution, and decreases with increasing stability constant of the complexes formed. Alpha-benzoinoxime allows the separation of these metal ions into three groups: V(V), Mo(VI) and W(VI) are extracted at pH=2, U(VI) at pH=5, Fe(II), Cu(II), Co(II) and Ni(II) at around pH=10.     

Direct voltammetric determination of Mo(VI) in plants: the need for a multivariate study of interferences

A multivariate modelling procedure using a second order composite design showed that the adsorptive stripping voltammetry (AdSV) technique used for molybdenum determination in a N,N-dimethylformamide (DMF)-ethanol-water homogeneous ternary solvent system (HTSS) using α-benzoinoxime (αBO) as the complexing agent and a sodium acetate-acetic acid buffer as the supporting electrolyte is much more tolerant to the presence of phosphorous (as phosphate) and iron than it could be presumed. Instead of the concentration ratios of P/Mo=100 and Fe/Mo=500, determined by univariate experiments, these values were respectively raised to 97,500 and 4200 when the phosphate and Fe(III) levels are varied simultaneously from 0.625 to 2.500 and from 0.006 to 0.150 mg l⁻¹, respectively, in the voltammetric cell, keeping the molybdenum concentration constant at 3.00 μg l⁻¹. This allowed us to propose a straightforward AdSV-HTSS procedure for the determination of Mo(VI) in plants. The AdSV results compared favourably with those obtained by using graphite furnace atomic absorption spectrometry (GFAAS) and with the results of samples from the International Plant-Analytical Exchange (IPE) programme of Wageningen University (The Netherlands).     

Sequential Injection Photometric Determination of Molybdenum Using Organic Wetting Film Extraction

Wetting film extraction was combined with colorimetry to determine nanogram amounts of molybdenum(VI). The simple extraction procedure enhanced sensitivity and selectivity while maintaining a high sample throughput. Extraction and back extraction steps were exploited to exclude interference from the 31 metal species and 11 anions tested. In the first step, molybdenum(VI) was extracted into a toluene film as an ion paired complex. Molybdenum(VI) reacted with thiocyanate to form anionic molybdenum(V) and/or molybdenum(VI) thiocyanate complexes. The complexes were extracted into a toluene film containing tetraheptylammonium bromide as ion pairing reagent. The thiocyanate ligands were displaced by 1,5-diphenylcarbazone (DPC) to form a more intensely colored complex (λ_max= 540 nm). DPC was introduced in the back extraction solvent, methanol. The relative standard deviation was 2.5% for 50 ng ml⁻¹of molybdenum(VI) (n= 10) at a rate of 25 samples h⁻¹. The detection limit (3 × baseline noise) was 2.5 × 10⁻⁸M.     

Separation of the Oxyanions of Re(VII), Mo(VI), Cr(VI), W(VI), and V(V) from a Multicomponent Solution at pH 6 by foam Fractionation

Abstract

An experimental investigation is presented of the foam separation of the oxyanions of Re(VII), Mo(VI), Cr(VI), W(VI), and V(V). The pH 6.0, multicomponent aqueous solutions are 1.0 × 10 ^?6 M in each metal. The effect of chloride competition with the metal oxyanions for the cationic surfactant is determined with NaCl concentrations up to 0.3 M. With proper NaCl concentration adjustments, V(V) can be separated completely from the other four metals, and Re(VII) and Mo(VI) from the other three. Pulsed surfactant dosage is investigated for 1.0 × 10 ^?6 M Mo(VI) solutions at pH 6.0 and 3.1.     

A solvent extraction study of molybdenum chloride and molybdenum thiocyanate complexes

The effect of reducing agents on molybdenum(VI) solutions in hydrochloric acid was studied by a solvent extraction technique to elucidate the composition of the colored molybdenum thiocyanate complex. Neither copper(I) chloride nor ascorbic acid have any effect on the extraction of MoO₂Cl₂; it is inferred that tin(II) chloride reduces Mo(VI) stepwise to a polynuclear Mo(V)·Mo(VI) complex and then to Mo(V). The colored thiocyanate complex produced by copper(I) and by ascorbic acid differs only slightly in extraction characteristics from the uncolored Mo(VI) complex. It is suggested that the color may be produced by an isomerization reaction of MoO₂(SCN)₂, and thus that the colored species may be a hexavalent rather than pentavalent molybdenum complex.     

Simultaneous spectrophotometric determination of molybdenum and selenium,and of molybdenum and tellurium

A method is reported for the extraction of molybdenum-phenylfluorone by chloroform. The extraction is complete whether perchlorate ions are present or not but the extractions in the presence of perchlorate ions gave a somewhat more sensitive procedure for the spectrophotometric determination of molybdenum in the solvent phase as the molybdenum-phenylfluorone complex.A procedure is reported for the simultaneous determination of molybdenum and selenium, and molybdenum and tellurium. The method involves first the formation and solvent extraction of the molybdenum-phenylfluorone complex by chloroform in the presence of perchlorate ions, followed by determination of selenium in the remaining aqueous phase as selenium-diethyldithiocarbamate complex after solvent extraction with 2-ethyl-1-hexanol in the presence of perchlorate ions. A similar procedure is reported for the simultaneous determination of molybdenum and tellurium except that in the determination of molybdenum, the phenylfluorone complex is extracted by chloroform in the absence of perchlorate ions. Tellurium is determined in the remaining aqueous phase as tellurium-diethyldithiocarbamate complex after solvent extraction by 2-ethyl-1-hexanol solvent extraction in the presence of perchlorate ions.     

Liquid-liquid extraction of molybdenum(VI) and uranium(VI) by LIX 622

The order of extraction of Mo(VI) from 1M acid solutions by 5% (v/v) LIX 622 (HL) in benzene is HCl>HNO₃>HClO₄>H₂SO₄, and extraction decreases with increasing concentration of HCl and H₂SO₄, and increases slightly with increasing concentration of HNO₃ and HClO₄. The extracted species is shown to be MoO₂L₂ as established by IR data of organic extracts and the extracted species in the solid form. Extraction is almost quantitative at and above 10% LIX 622, and is found to be independent of [Mo(VI)] in the range of 10^–4 to 10^–3 M. The diluents CCl₄, CHCl₃ and C₆H₆ are found to be superior to solvents of high dielectric constant for extraction of Mo(VI). Extraction of uranium(VI) by 10% (v/v) LIX 622 in benzene was found to increase with increasing equilibrium pH (3.0 to 6.0), and becomes quantitative at pH 5.9. Tributyl phosphate acts as a modifier up to 2% (v/v). Thorium(IV) is almost not extracted by LIX 622 or its mixture. Separation of Mo(VI) and U(VI) is feasible.     

Toluene/ter-butanol mixed solvent for the selective extraction of Cr(VI) from divalent heavy metals.

A solvent-extraction system comprising toluene/ter-butanol (ter-BuOH) mixed solvent as the organic phase was developed to selectively extract Cr(VI) from acidic chloride media in the presence of divalent metals, namely Cd(II), Co(II), Cu(II), Ni(II) and Zn(II) under 5 M CaCl2 salting-out conditions. Chromium(VI) was selectively extracted as a solvated ion-pair of [ter-BuOH2+ x CrO3Cl-] at ter-BuOH mole fractions of between 0.1 and 0.6 (9.0-57.2% in volume). Divalent metals were extracted at ter-BuOH mole fraction over 0.6 with extraction percents of Co (< 20%), Cu (< 15%), Ni (< 10%) and Zn (< 20%). The concentrations of Ca2+, water and ter-BuOH in the organic phase and ter-BuOH in the aqueous phase were determined to find out the effects on the extraction of Cr(VI). The chemical species of Cr(VI) in acidic chloride media containing 5 M CaCl2 and 0.1 M HCl was confirmed to be the CrO3Cl- species. The effects of the acid, salt concentrations in the aqueous phase and the solvent composition of a mixed organic solvent on the extraction of Cr(VI) were evaluated. Based on the above studies, the extraction mechanism was elucidated and the optimum extraction conditions were determined.     

Polarographic behaviour of uranium (VI) in organic solutions

Polarographic determination of uranium (VI) has been studied in the organic extraction phase TBP—diluent along with a selected aprotic solvent (i. e. dimethyl sulfoxide or N,N-dimethylformamide). DMF was found more suitable because it dissolves the organic extraction phase better than DMSO. U (VI) extracted in TBP-kerosene, n-hexane, cyclohexane, n-dodecane, benzene, from nitric acid medium can be determined in an organic solution (e. g. 50% DMF-30% TBP-20% kerosene) where it gives a well defined wave. In the organic solution, nitric acid added and/or extracted from the aqueous phase was found as an excellent supporting electrolyte for uranium determination.     

Extraction of molybdenum(VI) by 4-(5-nonyl)pyridine in benzene from aqueous mineral acid solutions containing thiocyanate ions

Extraction of Mo(VI) by 4-(5-nonyl)pyridine (NPy) in benzene from mineral acid solutions containing thiocyanate ions has been investigated at room temperature (23±2°C). From mineral acid (HCl, HNO₃, and H₂SO₄) solutions alone Mo(VI) is not extracted quantitatively while the presence of small amounts of KSCN in the system augments the extraction by a large factor. Stoichiometric studies indicate that ion-pair type complexes (NPyH)₂·[MoO₂(SCN)₄] are responsible for the extraction. Separation factors determined at fixed extraction conditions (0.1M Npy/C₆H₆–0.1M acid +0.2M KSCN) reveal that Ag(I), Cu(II), Co(II), Zn(II), Hg(II) and U(VI) are co-extracted while a clean separation from alkali metals, alkaline earths and some transition metals like Ln(III), Zr(IV), Hf(IV), Cr(III), Cr(VI) and Ir(III) is possible. Some of the complexing anions like oxalate, citrate, acetate, thiosulfate or ascorbate do not affect the degree of extraction of Mo(VI) allowing it to be recovered from diverse matrices.     

Extraction of metal ions with a primary amine

This paper describes some experimental results obtained at the extraction of sulfate solutions of U(VI), Mo(VI), V(V), Ce(IV), Zr(IV), Fe(III), Al(III) with a benzene solution of Primene JMT. The aqueous solutions consist of metal sulfates (or other metal salts) in the presence of sulfuric acid with a concentration range of 0–2.1 mol·dm^–3, the concentration of amine in the organic phase being 0.1–0.3 mol·dm^–3. The presence of various species of metal ions in the aqueous phase is considered and the equilibrium concentration of substances extracted in the organic phase is determined. On the basis of the results of chemical analysis (concentration of metals and sulfate ions) the composition of the prevailing complexes in the organic phase is proposed.     

Microwave-assisted solvent extraction and gas chromatography ion trap mass spectrometry procedure for the determination of persistent organochlorine pesticides (POPs) in marine sediment

Microwave-assisted solvent extraction of persistent organochlorine pesticides (POPs) in marine sediment was developed and optimized by means of two-level factorial designs. Six variables (microwave power, extraction time and temperature, amount of sample, solvent volume, and sample moisture) were considered as factors in the optimization process. The results show that the amount of sample to be extracted and solvent volume are statistically significant for the overall recovery of the studied pesticides, although compromise conditions have to be established with the object of avoiding overpressure in closed vessels. After extraction, a clean up step including the use of a silica cartridge was performed prior to chromatographic determination in order to remove interferences. The optimized procedure was compared to conventional Soxhlet extraction. The MS-MS ion preparation mode was applied to improve the sensitivity and selectivity of the chromatographic technique.     

Speciation, liquid-liquid extraction, sequential separation, preconcentration, transport and ICP-AES determination of Cr(III), Mo(VI) and W(VI) with calix-crown hydroxamic acid in high purity grade materials and environmental samples

A new functionalized calix[6]crown hydroxamic acid is reported for the speciation, liquid-liquid extraction, sequential separation and trace determination of Cr(III), Mo(VI) and W(VI). Chromium(III), molybdenum(VI) and tungsten(VI) are extracted at pH 4.5, 1.5 M HCl and 6.0 M HCl, respectively with calixcrown hydroxamic acid (37,38,39,40,41,42-hexahydroxy7,25,31-calix[6]crown hydroxamic acid) in chloroform in presence of large number of cations and anions. The extraction mechanism is investigated. The various extraction parameters, appropriate pH/M HCl, choice of solvent, effect of the reagent concentration, temperature and distribution constant have been studied. The speciation, preconcentration and kinetic of transport has been investigated. The maximum transport is observed 35, 45 and 30 min for chromium(III), molybdenum(VI) and tungsten(IV), respectively. For trace determination the extracts were directly inserted into the plasma for inductively coupled plasma atomic emission spectrometry, ICP-AES, measurements of chromium, molybdenum and tungsten which increase the sensitivity by 30-fold, with detection limits of 3 ng ml⁻¹. The method is applied for the determination of chromium, molybdenum and tungsten in high purity grade ores, biological and environmental samples. The chromium was recovered from the effluent of electroplating industries.     

Micro-determination of As(V), V(V), Mo(VI), W(VI) in the presence of Cu(II), Ni(II) and Zn(II)

A rapid procedure is described for the separation and determination of 0.025 mg to 1.0 mg quantities of As(V), V(V), Mo(VI) and W(VI) from small quantities of Cu(II), Ni(II), and Zn(II) using silica gel as the selective sorbent for the cations. The individual anionic components, which remain in the supernatant solution after separation from the cations, are determined by colorimetric methods. The complete recovery of As(V) in supernatant solution has also been tested radiometrically using⁷⁶As as the radioactive indicator. The sorbed cations after extraction with dilute hydrochloric acid are determined by EDTA titrations.     

Determination of chromium(VI) in the soil organic fraction

A procedure was developed for determining chromium(VI) in the soil organic fraction; it consisted of three steps: the preparation of a soil solution; the isolation and separation of chromium(VI) and chromium(III); and the determination of chromium(VI). Soil solutions were prepared by leaching soil samples with a Na₄P₂O₇ solution (the Rudd method). Chromium(VI) was extracted from the soil solution with a solution of sodium diethyldithiocarbamate in n-amyl alcohol; the conditions of the extraction and separation of chromium(VI) and chromium(III) were optimized. Chromium(VI) in solutions was determined after back extraction by spectrophotometry with diphenylcarbazide or by flame atomic absorption spectrometry. The procedure was validated using a reference soil sample, and the material balance of chromium in the systems under study was calculated.     

Test analysis method using ion pairs of pyrocatechol azo derivatives and trihydroxyfluorones with cetylpyridinium and their chelates with metal ions immobilized on paper

A two-stage procedure is proposed for the immobilization of ion pairs of pyrocatechol azo derivatives and trihydroxyfluorones and their chelates with metal ions on paper. It is demonstrated that ion pairs of phenylfluorone and thiazolylazopyrocatechol with cetylpyridinium can be used for the test determination of 0.01-10 mg/L Ti(IV), 0.05-20 mg/L Mo(VI), and 0.1–20 mg/L W(VI) and V(V) by the length of the colored zone of test strips after their contact with a test solution and for the determination of 0.01-0.5 mg/L Al and Mo(VI) and 0.001-0.1 mg/L Ti(IV) by the color intensity of reactive papers after passing a test solution. Chelates of Mo(VI) with tiazolylazopyrocatechol and of Sb(III) with phenylfluorone are used for the test determination of 0.01-1000 mg/L cationic surfactants. The selectivity of reactions is studied, and procedures are proposed for the determination of the above elements in different materials. The relative standard deviation of the results of analysis is no higher than 50%.     

Determination of aqueous plutonium oxidation states by solvent extraction

The reliability of two solvent extraction techniques for the determination of Pu oxidation states in solution was tested with low-ionic-strength solutions and with high-Na and high-Mg brines that contained Pu concentrations sufficient for spectrophotometric analysis. One procedure only differentiates between reduced Pu [Pu(III) and Pu(IV)] and oxidized Pu [Pu(V) and Pu(VI)], whereas the second procedure was designed to differentiate between Pu(IV), Pu(V), and Pu(VI) in solution. Both procedures successfully differentiated between oxidized and reduced Pu in both dilute solutions and brines when tested with samples that contained only the Pu(IV), Pu(V), or Pu(VI) oxidation states. However, when the second solvent extraction procedure, which differentiates between Pu(V) and Pu(VI), was employed for solutions that did not contain a strong oxidant to maintain the Pu(VI) oxidation state, significant quantities of Pu(VI) were reduced to Pu(V) during extraction, indicating that accurate quantification of Pu(V) and Pu(VI) is not possible with this procedure.Work supported by the U. S. Department of Energy under Contract DE-ACO6-76RLO 1830.