Giant dielectric constant response of the composites in ternary system CuO-TiO2-CaO

The subsolidus phase relations of the ternary system CuO-TiO₂-CaO sintered at 950 °C in air have been determined by powder X-ray diffraction method. Only one ternary compound CaCu₃Ti₄O₁₂ was found in this system. From room-temperature dielectric property mapping at 10 kHz, a giant dielectric constant (ε_r>10⁴) was observed for most of the ceramic composites in the CuO-rich region and in the region along the CaO-CuO binary line. The composites in the CaCu₃Ti₄O₁₂-rich region were found to give a comparable giant dielectric constant when sintered at 1050 °C. The particular microstructure of larger grains with predominant phase surrounded by smaller grains with the secondary phases was found in such composites with a high dielectric constant. The relations between structures and dielectric properties were investigated. An internal barrier layer capacitance effect is the most probable mechanism to explain this particular dielectric behavior.     

Sol-gel synthesis of mesoporous CaCu3Ti4O12 thin films and their gas sensing response

A new sol-gel synthesis procedure of stable calcium copper titanate (CaCu₃Ti₄O₁₂—CCTO) precursor sols for the fabrication of porous films was developed. The composition of the sol was selected in order to avoid the precipitation of undesired phases; ethanol was used as solvent, acetic acid as modifier and poly(ethyleneglycol) as a linker agent. Films deposited by spin-coating onto oxidized silicon substrates were annealed at 700 °C. The main phase present in the samples, as detected by X-ray diffraction and Raman spectroscopy, was CaCu₃Ti₄O₁₂. Scanning electron microscopy analysis showed that mesoporous structures, with thicknesses between 200 and 400 nm, were developed as a result of the processing conditions. The films were tested regarding their sensibility towards oxygen and nitrogen at atmospheric pressure using working temperatures from 200 to 290 °C. The samples exhibited n-type conductivity, high sensitivity and short response times. These characteristics indicate that CCTO mesoporous structures obtained by sol-gel are suitable for application in gas sensing.     

Effect of the addition of B2O3 and BaO-B2O3-SiO2 glasses on the microstructure and dielectric properties of giant dielectric constant material CaCu3Ti4O12

The effect of the addition of glassy phases on the microstructure and dielectric properties of CaCu₃Ti₄O₁₂ (CCTO) ceramics was investigated. Both single-component (B₂O₃) and multi-component (30 wt% BaO-60 wt% B₂O₃-10 wt% SiO₂ (BBS)) glass systems were chosen to study their effect on the density, microstructure and dielectric properties of CCTO. Addition of an optimum amount of B₂O₃ glass facilitated grain growth and an increase in dielectric constant. However, further increase in the B₂O₃ content resulted in its segregation at the grain boundaries associated with a reduction in the grain size. In contrast, BBS glass addition resulted in well-faceted grains and increase in the dielectric constant and decrease in the dielectric loss. An internal barrier layer capacitance (IBLC) model was invoked to correlate the dielectric constant with the grain size in these samples.     

A novel microwave dielectric ceramic Ca2Zn4Ti16O38: Preparation and dielectric properties

A novel microwave dielectric powder with composition of Ca₂Zn₄Ti₁₆O₃₈ was synthesized through a citrate sol-gel process. The development of crystalline phases with heat-treating temperature for the gel derived powders was evaluated by using thermo-gravimetric analysis and X-ray powder diffraction analysis techniques. The pure phase of Ca₂Zn₄Ti₁₆O₃₈ with crichtonite crystal structure was obtained at relatively low temperature of 1000 °C. The synthesized powder has high reactivity and the dense ceramics with single crystalline phase were obtained at low sintering temperature of 1100 °C. Impedance spectroscopy and microwave dielectric measurements on sintered samples showed the present compound to be a modest dielectric insulator with excellent dielectric properties of ε_r∼47-49, Qf value ∼27,800-31,600 GHz and τ_f∼+45 to +50 ppm/°C. It shows comparable microwave dielectric properties to other moderate-permittivity microwave dielectrics, but much lower sintering temperature of 1100 °C.     

The chemical and dielectric properties of epoxy/(Ba0.8Sr0.2)(Ti0.9Zr0.1)O3 composites for embedded capacitor application

The characteristics of epoxy/(Ba_0.8Sr_0.2)(Ti_0.9Zr_0.1)O₃ (BSTZ) composites are investigated for the further application in embedded capacitor device. The effects of BSTZ ceramic powder filler ratio on the chemical, physical and dielectric properties of epoxy/BSTZ composites are studied. Differential scanning calorimeter (DSC) thermal analysis is conducted to determine the optimum values of hardener agent, curing temperature, reaction heat, and glass transition temperature (T_g). The hardener reaction process starts at about 115 °C and completes at about 200 °C, for that it is appropriate to process of epoxy/BSTZ composites in the range of temperature. The highest glass transition temperature (T_g) of 155 °C is obtained at one equivalent weight ratio (hardener/epoxy). Only the BSTZ phase can be detected in the XRD patterns of epoxy/BSTZ composites. The more BSTZ ceramic powder is mixed with epoxy, the higher crystalline intensity of tetragonal BSTZ phase are revealed in the XRD patterns. The dielectric constant measured at 1 MHz increases from 5.8 to 23.6 as the content of BSTZ ceramic powder in the epoxy/BSTZ composites increases from 10 to 70 wt%. The loss tangents of the epoxy/BSTZ composites slightly increase with the increase of measurement frequency.     

Effect of surface fluorination and conductive additives on the electrochemical behavior of lithium titanate (Li4/3Ti5/3O4) for lithium ion battery

Effect of surface fluorination and conductive additives on the charge/discharge behavior of lithium titanate (Li_4/3Ti_5/3O₄) has been investigated using F₂ gas and vapor grown carbon fiber (VGCF). Surface fluorination of Li_4/3Ti_5/3O₄ was made using F₂ gas (3 × 10⁴ Pa) at 25-150 °C for 2 min. Charge capacities of Li_4/3Ti_5/3O₄ samples fluorinated at 70 °C and 100 °C were larger than those for original sample at high current densities of 300 and 600 mA/g. Optimum fluorination temperatures of Li_4/3Ti_5/3O₄ were 70 °C and 100 °C. Fibrous VGCF with a large surface area (17.7 m²/g) increased the utilization of available capacity of Li_4/3Ti_5/3O₄ probably because it provided the better electrical contact than acetylene black (AB) between Li_4/3Ti_5/3O₄ particles and nickel current collector.     

(La0.4Ba0.4Ca0.2)(Mn0.4Ti0.6)O3: A new titano-manganate with a high dielectric constant and antiferromagnetic interactions

A new perovskite-based titano-manganate, (La_0.4Ba_0.4Ca_0.2)(Mn_0.4Ti_0.6)O₃, has been prepared by the ceramic route at 1100°C. This oxide was found to possess the cubic perovskite structure with  Å (space group ). The refined composition as obtained by Rietveld analysis of powder X-ray data was found to be (La_0.44Ba_0.38Ca_0.18)(Mn_0.43Ti_0.57)O_2.91(3) (R_p=0.0704, wR_p=0.0828). The composition was also ascertained by Energy dispersive X-ray analysis. Iodometric studies led to a slightly higher oxygen content (compared to Rietveld refinement) corresponding to an average manganese oxidation state of 3.05. The above oxide was found to exhibit high dielectric constant (ε) of 6980 at 1 kHz decreasing to 590 at 100 kHz. At high temperatures (200°C) it shows an unusually high dielectric constant of 20,000 at 1 kHz. In addition to the dielectric properties, detailed magnetic studies show evidence of long-range antiferromagnetic interactions near 5 K. The presence of unusually high dielectric constant coupled with the long-range magnetic interactions may open up interesting applications.     

Preparation of a new pyrochlore-type compound Na0.32Bi1.68Ti2O6.46(OH)0.44 by hydrothermal reaction

A new pyrochlore-type Na_0.32Bi_1.68Ti₂O_6.46(OH)_0.44 with the cubic cell of a=10.339(5) Å was prepared by hydrothermal reaction using TiO₂ (anatase) and Bi₂O₃ in NaOH solution. This compound was obtained when the molar ratio of NaOH/TiO₂ was above 2 and the reaction temperature was above 240 °C. The TG-curve of as-prepared sample showed a mass loss of 0.8 mass% which was caused by release of OH group. This compound decomposed to a pyrochlore-type compound and a layered-type Na_0.5Bi_4.5Ti₄O₁₅ above 800 °C. The optical band gap of Na_0.32Bi_1.68Ti₂O_6.46(OH)_0.44 was estimated to be 2.5 eV.     

Role of doping and CuO segregation in improving the giant permittivity of CaCu3Ti4O12

The dopant role on the electric and dielectric properties of the perovskite-type CaCu₃Ti₄O₁₂ (CCTO) compound is evidenced. Impedance spectroscopy measurements show that the relevant permittivity value attributed to sintered CCTO is due to grain boundary (g.b.) effects. The g.b. permittivity value of the pure CCTO can be increased of 1-2 orders of magnitude by cation substitution on Ti site and/or segregation of CuO phase, while the bulk permittivity keeps values 90<ε_r<180. Bulk and g.b. conductivity contributions are discussed: electrons are responsible for the charge transport and a mean bulk activation energy of 0.07 eV is obtained at room temperature for all the examined samples. The g.b. activation energy ranges between 0.54 and 0.76 eV. Defect models related to the transport properties are proposed, supported by electron paramagnetic resonance measurements.     

Synthesis, structure and electrical properties of Cu3.21Ti1.16Nb2.63O12 and the CuOx-TiO2-Nb2O5 pseudoternary phase diagram

Subsolidus phase relations in the CuO_x-TiO₂-Nb₂O₅ system were determined at 935 °C. The phase diagram contains one new phase, Cu_3.21Ti_1.16Nb_2.63O₁₂ (CTNO) and one rutile-structured solid solution series, Ti_1−3xCu_xNb_2xO₂: 0<x<0.2335 (35). The crystal structure of CTNO is similar to that of CaCu₃Ti₄O₁₂ (CCTO) with square planar Cu²⁺ but with A site vacancies and a disordered mixture of Cu⁺, Ti⁴⁺ and Nb⁵⁺ on the octahedral sites. It is a modest semiconductor with relative permittivity ∼63 and displays non-Arrhenius conductivity behavior that is essentially temperature-independent at the lowest temperatures.     

Thermo-Raman spectroscopy in situ monitoring study of solid-state synthesis of NiO-Al2O3 nanoparticles and its characterization

Hyphenation of thermogravimetric analyzer (TGA) and thermo-Raman spectrophotometer for in situ monitoring of solid-state reaction in oxygen atmosphere forming NiO-Al₂O₃ catalyst nanoparticles is investigated. In situ thermo-Raman spectra in the range from 200 to 1400 cm⁻¹ were recorded at every degree interval from 25 to 800 °C. Thermo-Raman spectroscopic studies reveal that, although the onset of formation is around 600 °C, the bulk NiAl₂O₄ forms at temperatures above 800 °C. The X-ray diffraction (XRD) spectra and the scanning electron microscopy (SEM) images of the reaction mixtures were recorded at regular temperature intervals of 100 °C, in the temperature range from 400 to 1000 °C, which could provide information on structural and morphological evolution of NiO-Al₂O₃. Slow controlled heating of the sample enabled better control over morphology and particle size distribution (∼20-30 nm diameter). The observed results were supported by complementary characterizations using TGA, XRD, SEM, transmission electron microscopy, and energy dispersive X-ray analysis.     

Preparation and photocatalytic activity of ZnO/TiO2/SnO2 mixture

ZnO/TiO₂/SnO₂ mixture was prepared by mixing its component solid oxides ZnO, TiO₂ and SnO₂ in the molar ratio of 4?1?1, followed by calcining the solid mixture at 200-1300 °C. The products and solid-state reaction process during the calcinations were characterized with powder X-ray diffraction (XRD), thermogravimetric and differential thermal analysis (TG-DTA), UV-Vis diffuse reflectance spectroscopy (UV-Vis DRS) and Brunauer-Emmett-Teller measurement of specific surface area. Neither solid-state reaction nor change of crystal phase composition took place among the ZnO, TiO₂ and SnO₂ powders on the calcinations up to 600 °C. However, formation of the inverse spinel Zn₂TiO₄ and Zn₂SnO₄ was detected at 700-900 and 1100-1200 °C, respectively. Further increase of the calcination temperature enabled the mixture to form a single-phase solid solution Zn₂Ti_0.5Sn_0.5O₄ with an inverse spinel structure in the space group of . The ZnO/TiO₂/SnO₂ mixture was photocatalytically active for the degradation of methyl orange in water; its photocatalytic mass activity was 16.4 times that of SnO₂, 2.0 times that of TiO₂, and 0.92 times that of ZnO after calcination at 500 °C for 2 h. But, the mass activity of the mixture decreased with increasing the calcination temperature at above 700 °C because of the formation of the photoinactive Zn₂TiO₄, Zn₂SnO₄ and Zn₂Ti_0.5Sn_0.5O₄. The sample became completely inert for the photocatalysis after prolonged calcination at 1300 °C (42 h), since all of the active component oxides were reacted to form the solid solution Zn₂Ti_0.5Sn_0.5O₄ with no photocatalytic activity.     

Effect of sintering on the ionic conductivity of garnet-related structure Li5La3Nb2O12 and In- and K-doped Li5La3Nb2O12

Garnet-structure related metal oxides with the nominal chemical composition of Li₅La₃Nb₂O₁₂, In-substituted Li_5.5La₃Nb_1.75In_0.25O₁₂ and K-substituted Li_5.5La_2.75K_0.25Nb₂O₁₂ were prepared by solid-state reactions at 900, 950, and 1000 °C using appropriate amounts of corresponding metal oxides, nitrates and carbonates. The powder XRD data reveal that the In- and K-doped compounds are isostructural with the parent compound Li₅La₃Nb₂O₁₂. The variation in the cubic lattice parameter was found to change with the size of the dopant ions, for example, substitution of larger In³⁺(r_CN6: 0.79 Å) for smaller Nb⁵⁺ (r_CN6: 0.64 Å) shows an increase in the lattice parameter from 12.8005(9) to 12.826(1) Å at 1000 °C. Samples prepared at higher temperatures (950, 1000 °C) show mainly bulk lithium ion conductivity in contrast to those synthesized at lower temperatures (900 °C). The activation energies for the ionic conductivities are comparable for all samples. Partial substitution of K⁺ for La³⁺ and In³⁺ for Nb⁵⁺ in Li₅La₃Nb₂O₁₂ exhibits slightly higher ionic conductivity than that of the parent compound over the investigated temperature regime 25-300 °C. Among the compounds investigated, the In-substituted Li_5.5La₃Nb_1.75In_0.25O₁₂ exhibits the highest bulk lithium ion conductivity of 1.8×10⁻⁴ S/cm at 50 °C with an activation energy of 0.51 eV. The diffusivity (“component diffusion coefficient”) obtained from the AC conductivity and powder XRD data falls in the range 10⁻¹⁰-10⁻⁷ cm²/s over the temperature regime 50-200 °C, which is extraordinarily high and comparable with liquids. Substitution of Al, Co, and Ni for Nb in Li₅La₃Nb₂O₁₂ was found to be unsuccessful under the investigated conditions.     

Ferroelectric perovskite-type barium copper niobate: BaCu1/3Nb2/3O3

A perovskite-type BaCu_1/3Nb_2/3O₃ was prepared by high temperature reaction using BaCO₃, CuO and Nb₂O₅. The X-ray powder diffraction pattern of this compound was indexed with the tetragonal cell with the lattice parameters of a=4.0464(4) and c=4.1807(4) Å (c/a=1.033). This compound had the tetragonal perovskite-type structure in which the B site was occupied statistically by Nb and Cu atoms. From high temperature X-ray powder diffraction patterns this compound had a phase transition from the tetragonal to cubic symmetry in the temperature range of 500-600 °C. The P-E and S-E hysteresis loops occurred at room temperature and the apparent maximum in the temperature dependence of the dielectric constant was observed at 520 °C. The temperature dependence of the inverse of magnetic susceptibility exhibited paramagnetic behavior.     

Investigation on the growth of CaCu3Ti4O12 thin film and the origins of its dielectric relaxations

Using the radio frequency magnetron sputtering, CaCu₃Ti₄O₁₂ (CCTO) thin films were deposited on platinized silicon substrates. The influence of annealing temperature on structures and morphologies of the thin films was investigated. The high annealing temperature increased the crystallinity of the films. Temperature dependence of the dielectric constant revealed an amazing different characteristic of the dielectric relaxation at ∼10 MHz, whose characteristic frequency abnormally increased with the decrease of the measuring temperature unlike the relaxations due to extrinsic origins. Meanwhile, the dielectric constant at high frequencies was close to the value derived from the first principle calculation. All these gave the evidences to ascribe this relaxation to the intrinsic mechanism.     

Defect microstructures of TiO2 rutile due to Zr dissolution and expulsion

Defect microstructure of Zr-dissolved TiO₂ polycrystals, homogenized as rutile structure at 1600 °C and then aged at 900 °C for 2-200 h in air, was characterized by analytical electron microscopy. Diffuse diffractions occurred at 1/2(211) as a result of Zr⁴⁺ substitution for Ti⁴⁺ with volume/charge compensating defect clusters. Upon annealing at 900 °C, plate-like Guinier and Preston (G.P.) zone appeared with the plate surface parallel to (100) and (010) and in association with dislocations. Commensurate superstructures with apparent triple {101} and {111} periodicity also occurred as metastable intermediates, which are presumably the precursor of the equilibrium ZrTi₂O₆ precipitate.     

New high permittivity tetragonal tungsten bronze dielectrics Ba2LaMNb4O15: M=Mn, Fe

The new phases Ba₂LaMNb₄O₁₅: M=Mn, Fe were prepared by solid state reaction at 1100 °C. They have the tetragonal tungsten bronze structure, space group P4/mbm, at room temperature. The two octahedral sites show partial order of M and Nb with preferential occupancy of the smaller B(1) sites by M. Both phases have high permittivities 90±15 over the range 10-320 K. Ba₂LaFeNb₄O₁₅ is highly insulating with bulk conductivity ?10⁻⁸ ohm⁻¹ cm⁻¹ at 25 °C and tan δ?0.001 over the range 100-320 K and at 10⁵ Hz. Solid solutions between these new phases and the compositionally and structurally related relaxor ferroelectric Ba₂LaTi₂Nb₃O₁₅ show gradual loss of ferroelectric behaviour attributed to replacement of polarisable Ti⁴⁺ by a mixture of (Mn, Fe)³⁺ and Nb⁵⁺.     

Effect of magnetostrictive phase on structural, dielectric and electrical properties of NiFe2O4 + Pb0.93La0.07(Zr0.60Ti0.40)O3 composites

Particulate composites of NiFe₂O₄ (NFO) and Pb_0.93La_0.07 (Zr_0.60Ti_0.40) O₃ (PLZT) were synthesized by solid-state reaction technique. Structure and surface morphological studies were carried out using X-ray diffraction and scanning electron microscopy techniques, respectively. Frequency dependent variation of dielectric constant (), loss tangent (tan δ) and ac resistivity for (x) NFO + (1−x) PLZT composites in the range 100 Hz–5 MHz at room temperature were studied. The temperature dependence of dielectric constant (′), loss tangent (tan δ) was studied in wide temperature range of measurement at fixed frequencies. Also DC resistivity measurements were carried out in the temperature range of 300 K–923 K. Structural, dielectric and electrical properties show notable change due to presence of magnetostrictive NFO phase along with PLZT.     

Structural phase transitions in the relaxor ferroelectric Pb2Bi4Ti5O18

The relaxor ferroelectric Pb₂Bi₄Ti₅O₁₈ has been studied by Rietveld refinement of powder neutron diffraction data collected at temperatures of 100, 250 and 400 °C. Our refinements are compatible with the ‘average’ crystal structure of Pb₂Bi₄Ti₅O₁₈ undergoing the phase transition sequence F2mm→I4mm→I4/mmm as a function of increasing temperature, with the latter phase being observed above the known ferroelectric Curie temperature, T_m, and the intermediate phase consistent with a previously observed dielectric anomaly around 207 °C. The results are, however, in conflict with both observation of a symmetry lowering (to space group B2eb) in the lowest temperature phase, observed by electron diffraction, and also with electrical property measurements, which suggest both a- and c-axis polarisation up to T_m. Nevertheless, these crystallographic results are consistent with the observation of relaxor behaviour in this material, and underline the importance of considering ‘long-range’ versus ‘local’ structural effects in relaxor materials.     

Visible and infrared luminescence properties of Er-doped Y2Ti2O7 nanocrystals

Er³⁺-doped Y₂Ti₂O₇ nanocrystals were fabricated by the sol-gel method. While the annealing temperature exceeds 757 °C, amorphous pyrochlore phase Er_xY_2−xTi₂O₇ transfers to well-crystallized nanocrystals, and the average crystal size increases from ∼70 to ∼180 nm under 800-1000 °C/1 h annealing. Er_xY_2−xTi₂O₇ nanocrystals absorbing 980 nm photons can produce the upconversion (526, 547, and 660 nm; ²H_11/2→⁴I_15/2, ⁴S_3/2→⁴I_15/2, and ⁴F_9/2→⁴I_15/2, respectively) and Stokes (1528 nm; ⁴I_13/2→⁴I_15/2) photoluminescence (PL). The infrared PL decay curve is single-exponential for Er³⁺ (5 mol%)-doped Y₂Ti₂O₇ nanocrystals but slightly nonexponential for Er³⁺ (10 mol%)-doped Y₂Ti₂O₇ nanocrystals. For 5 and 10 mol% doping concentrations, the mechanism of up-converted green light is the two-photon excited-state absorption. Much stronger intensity of red light relative to green light was observed for the sample with 10 mol% dopant. This phenomenon can be attributed to the reduced distance between Er³⁺-Er³⁺ ions, resulting in the enhancement of the energy-transfer upconversion and cross-relaxation mechanisms.