Surface water preparation procedure for chromatographic determination of polycyclic aromatic hydrocarbons and polychlorinated biphenyls

A new sample preparation procedure for the analysis of polycyclic aromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs) in water containing suspended particulate matter (SPM) has been developed. A specially designed filtration vessel coupled directly to an SPE cartridge was used for this purpose. SPM separation and analyte isolation/concentration were carried out in a single step. Both the SPE cartridge and the suspended matter collected on the filter were solvent extracted, and analyte recoveries were determined. Analyte recoveries from the filtrate ranged from 64 to 100% of the spiked amount for PAHs with the highest aqueous solubilities, and did not exceed 20% for those with the lowest solubilities. Total recoveries of PAHs from surface water containing 21 mg l(-1) SPM ranged from 65 to 121%. PCB recoveries from the particulate matter reached over 10% of the spiked amount, while those from the filtrate ranged from 20 to 57%. Total PCBs recoveries ranged from 34 to 69%.     

Polycyclic aromatic hydrocarbon analysis in different matrices of the marine environment

Polycyclic aromatic hydrocarbons (PAHs) were determined in marine samples of various types, i.e. seawater, sediment and mussel homogenate samples. The samples were spiked with standard PAH mixtures in both polar (acetonitrile) and non-polar (i-octane) solvents, then extracted. Extraction from seawater was performed by liquid/liquid extraction to hexane (LLE) and with solid phase extraction (SPE) discs. The water samples were filtered and unfiltered seawater, and redistilled water for comparison. The discs with PAHs adsorbed from water samples, and also the sediment and mussel homogenate samples, were extracted with acetonitrile by sonication. PAHs in the disc extracts and from the LLE were cleaned-up using TLC and next determined by GC/MS/IT (with ion-trap) and HPLC-DAD/UV. The analytical procedures were verified with deuterated PAH standard mixtures. The large differences in PAH recoveries (from 12 to 86% for sum, and from 3 to 135% for particular PAHs) do not depend solely on the type of matrix and analytical procedure applied (e.g. standard solvent, volume of evaporated sample), but also on the concentration and molecular structure of the analyte. Usually, only a fraction of each PAH content in the matrix is determined, depending on the particulate matter in seawater and the sorption properties of the solid matrix. The recoveries of deuterated PAHs are higher than those of non-deuterated compounds.     

PAH and PCB determination of the concentration gradient in moss Pleurozium schreberi near a highway,and seasonal variability at the background reference site

Moss (Pleurozium schreberi) was investigated as biomonitor of atmospheric polycyclic aromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs). Samples were collected at a distance of 10, 50 and 100 m from a highway and were seasonally collected in a forest stand near a regional background air pollution station situated approximately 30 km from the highway. The samples from the background area were dried using two different techniques in parallel, air-drying and freeze-drying. Simultaneous pressurised liquid extraction of PAHs and PCBs was performed, followed by purification using gel permeation chromatography of the crude extract. The concentration of the 15 most important Environmental Protection Agency (EPA) PAHs was determined by gas chromatography coupled with ion-trap mass spectrometry with a selected ion storage acquisition programme, and the PCB concentrations were determined using a mass spectrometer operated in tandem mass spectrometry (MS/MS) mode. Acceptable recoveries and quality parameters for PAHs and PCBs were achieved with the use of pressurised liquid extraction followed by gel permeation chromatography. The detection limit was <0.76 ng g^?1 for PAHs and <0.04 ng g^?1 for PCBs. Possible contamination of the moss samples by 3-ring PAHs and PCBs in the atmosphere was found during air drying. Increased PAH and PCB concentrations caused by car engine exhausts and by asphalt and oil evaporation were found near the highway. Generally, the PAH and PCB concentrations in moss decreased exponentially with distance from the highway. The organic compound concentrations close to the background station showed seasonal fluctuations corresponding to the fluctuations in the local air temperature and particle concentration.     

Optimization and validation of HPLC-UV-DAD and HPLC-APCI-MS methodologies for the determination of selected PAHs in water samples

Polycyclic aromatic hydrocarbons (PAHs) are environmental contaminants resulting from emissions of a variety of sources including industrial combustion, discharge of fossil fuels, and residential heating. Because of their mutagenic and carcinogenic properties, the study of PAHs in environmental matrices is of great importance. In this work, the extraction of 9 out of the 16 PAH priority pollutants according to the U.S. Environmental Protection Agency is carried out through liquid-liquid extraction (LLE) and solid-phase extraction (SPE). The determination of PAHs is made by high-performance liquid chromatography with diode-array detection and liquid chromatography-atmospheric pressure chemical ionization mass spectrometry. Between the extraction techniques used, LLE is revealed to be efficient in the extraction of the higher molecular weight PAHs, though SPE is adequate for the extraction of all PAHs. In the real water samples analyzed, no PAH is detected under the analysis conditions used.     

Sources of Errors Associated with the Determination of PAH and PCB Analytes in Water Samples

Abstract

This work describes the problems occurring in routine determination of polyaromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs) in water. On the basis of experiments carried out, sources of analyte losses in a particular step of the analytical procedure were identified and assessed. Primary attention has been paid to evaluation of the?following:

• degree of adsorption of analytes from the group of PCBs and PAHs on the walls of glass vessels used during sample pretreatment and storage

• influence of excess of solvent evaporation from extracts on analyte recoveries

• influence of material of extraction column (glass, polyethylene) on analyte recovery during the solid extraction process.

     

Fully automated trace level determination of parent and alkylated PAHs in environmental waters by online SPE-LC-APPI-MS/MS

Polycyclic aromatic hydrocarbons (PAHs) are ubiquitous compounds that enter the environment from natural and anthropogenic sources, often used as markers to determine the extent, fate, and potential effects on natural resources after a crude oil accidental release. Gas chromatography-mass spectrometry (GC-MS) after liquid–liquid extraction (LLE+GC-MS) has been extensively used to isolate and quantify both parent and alkylated PAHs. However, it requires labor-intensive extraction and cleanup steps and generates large amounts of toxic solvent waste. Therefore, there is a clear need for greener, faster techniques with enough reproducibility and sensitivity to quantify many PAHs in large numbers of water samples in a short period of time. This study combines online solid-phase extraction followed by liquid chromatography (LC) separation with dopant-assisted atmospheric pressure photoionization (APPI) and tandem MS detection, to provide a one-step protocol that detects PAHs at low nanograms per liter with almost no sample preparation and with a significantly lower consumption of toxic halogenated solvents. Water samples were amended with methanol, fortified with isotopically labeled PAHs, and loaded onto an online SPE column, using a large-volume sample loop with an auxiliary LC pump for sample preconcentration and salt removal. The loaded SPE column was connected to an UPLC pump and analytes were backflushed to a Thermo Hypersil Green PAH analytical column where a 20-min gradient separation was performed at a variable flow rate. Detection was performed by a triple-quadrupole MS equipped with a gas-phase dopant delivery system, using 1.50 mL of chlorobenzene dopant per run. In contrast, LLE+GC-MS typically use 150 mL of organic solvents per sample, and methylene chloride is preferred because of its low boiling point. However, this solvent has a higher environmental persistence than chlorobenzene and is considered a carcinogen. The automated system is capable of performing injection, online SPE, inorganic species removal, LC separation, and MS/MS detection in 28 min. Selective reaction monitoring was used to detect 28 parent PAHs and 15 families of alkylated PAHs. The methodology is comparable to traditional GC-MS and was tested with surface seawater, rainwater runoff, and a wastewater treatment plant effluent. Positive detections above reporting limits are described. The virtual absence of sample preparation could be particularly advantageous for real-time monitoring of discharge events that introduce PAHs into environmental compartments, such as accidental releases of petroleum derivates and other human-related events. This work covers optimization of APPI detection and SPE extraction efficiency, a comparison with LLE+GC-MS in terms of sensitivity and chromatographic resolution, and examples of environmental applications.     

Determination of sixteen polycyclic aromatic hydrocarbons in aqueous and solid samples from an Italian wastewater treatment plant

A robust procedure for the determination of 16 US EPA PAHs in both aqueous (e.g. wastewaters, industrial discharges, treated effluents) and solid samples (e.g. suspended solids and sludge) from a wastewater treatment plant (WWTP) is presented. Recovery experiments using different percentages of organic modifier, sorbents and eluting solvent mixtures were carried out in Milli-Q water (1000 mL) spiked with a mixture of the PAH analytes (100 ng/L of each analyte). The solid phase extraction (SPE) procedures applied to spiked waste water samples (1000 mL; 100 ng/L spiking level) permitted simultaneous recovery of all the 16PAHs with yields >70% (6-13% RSD). SPE clean up procedures applied to sewage and stabilized sludge extracts, showed percent recoveries in the range 73-92% (7-13% RSD) and 71-89% (7-12% RSD), respectively. The methods were used for the determination of PAHs in aqueous and solid samples from the WWTP of Fusina (Venice, Italy). Mean concentrations, as the sum of the 16PAHs in aqueous and suspended solid samples, were found to be approx. in the 1.12-4.62 microg/L range. Sewage and stabilized sludge samples contained mean PAH concentrations, as sum of 16 compounds, in the concentration range of 1.44-1.26 mg/kg, respectively. Extraction and clean up procedures for sludge samples were validated using EPA certified reference material IRM-104 (CRM No. 912). Instrumental analyses were performed by coupling HPLC with UV-diode array detection (UV-DAD) and fluorescence detection (FLD).     

Persistent organic pollutants (POPs) at Ross Sea (Antarctica)

The most significant findings on the presence of persistent organic pollutants (POPs) in the marine ecosystem at Ross Sea are presented. Seawater samples were collected in many sampling sites located in a large area of the Ross Sea during various Italian expeditions in Antarctica. Two classes of POPs were considered, namely polychlorobiphenyls (PCBs) and polycyclic aromatic hydrocarbons (PAHs). The results highlighted the presence of these compounds in seawater samples at a total concentration level of about 50 pg/l for PCBs, and 220 pg/l for PAHs. Moreover, seawater samples showed low to high molecular weight PAHs (LMW/HMW) and phenanthrene to anthracene (PHE/ANT) ratios higher than 1 and 5, respectively, which may suggest the predominance of a petrogenic source (i.e. petroleum product contamination). Results were also obtained on the POP depth profile in the water column at Cape Adere, where two water masses converge and mix, i.e. the Modified Circumpolar Deep Water (MCDW) and the High Salinity Shelf Water (HSSW). According to both the PAH and temperature profiles a two-fold higher PAH and PCB concentration was observed for MCDW samples with respect to HSSW. This result represents the first experimental evidence of the external input of pollutants in this area of the Ross Sea coming from the outer oceanic circulation.     

A comparison of the performance of two chromatographic and three extraction techniques for the analysis of PAHS in sources of drinking water

The aim of this work is to establish a sensitive and reliable method for the analysis of the 16 priority Environmental Protection Agency-defined polycyclic aromatic hydrocarbons (PAHs) found in water samples. Gas chromatography (GC)-mass spectrometry (MS) and high-performance liquid chromatography (HPLC)-fluorescence detection (FLD)-UV techniques are optimized to obtain an adequate resolution of all compounds. Validation of the methods is carried out, and a good performance is observed for both techniques. The HPLC-FLD-UV technique is somewhat more sensitive than the GC-MS technique for the determination of PAHs; thus, the HPLC-FLD-UV method is used to follow up both the solid-phase extraction (SPE) analysis using cartridges and discs and the liquid-liquid extraction (LLE), which are also evaluated for the extraction of the PAHs. Low recoveries between 43% and 79% are obtained using SPE cartridges, and higher values are obtained using SPE discs (56-96%) and LLE (60-105%). Better results are obtained using the LLE technique, and, thus, analysis of real water samples is carried out using this technique. LODs between 0.6 and 21 ng/L and relative standard deviations less than 15% are obtained using a spiked water sample analyzed using the full LLE HPLC-FLD-UV method.     

Ultrasound‐assisted magnetic SPE based on Fe3O4‐grafted graphene for the determination of polychlorinated biphenyls in water samples

An ultrasound‐assisted magnetic SPE procedure with an Fe₃O₄‐grafted graphene nanocomposite as the magnetic adsorbent has been developed to determine seven polychlorinated biphenyls (PCBs; PCB28, PCB52, PCB101, PCB118, PCB138, PCB153, and PCB180) simultaneously in 200 mL environmental water samples, in combination with GC–MS/MS. Several factors related to magnetic SPE efficiencies, such as the superparamagnetic intensity and amount of adsorbent, extraction time, sample pH, and desorption conditions were investigated. With the assistance of ultrasound, the extraction achieved the maximum within only 20 s, attributed to the powerful adsorptive ability of the magnetic adsorbent toward the PCBs. Under the optimized conditions, an excellent linearity was observed in the range of 0.1–100 ng/L for PCB28, 0.2–100 ng/L for PCB52, and 0.5–100 ng/L for the other five PCBs with the correlation coefficients ranging from 0.9988 to 0.9996. The mean recoveries at spiked levels of 5.0 and 10.0 ng/L were 84.9–108.5%, the coefficients of variations were <6.5%. With convenient magnetic separation, the synthesized magnetic adsorbent could be recycled more than ten times. The proposed method was demonstrated to be feasible, simple, rapid, and easy to operate for the trace analysis of the PCBs in environmental water samples.     

Determination of selected polychlorinated biphenyls in water samples by ultrasound-assisted emulsification-microextraction and gas chromatography-mass-selective detection

Ultrasound-assisted emulsification-microextraction (USAEME) procedure was developed for the determination of selected polychlorinated biphenyls (PCBs) in 10 mL of water samples by gas chromatography-mass-selective detection. After determination of the most suitable solvent and extraction time, several other parameters including solvent volume, centrifugation time and ionic strength of the sample were optimized using a 2³ factorial experimental design. The optimized USAEME procedure used 200 μL of chloroform as extraction solvent, 10 min of extraction with no ionic strength adjustment at 25 °C and 5 min of centrifugation at 4000 rpm. The limits of detection ranged from 14 ng L⁻¹ (for PCB153) to 30 ng L⁻¹ (for PCB101). Recoveries of PCBs from fortified distilled water are over 80% for three different fortification levels between 0.1 and 5 μg L⁻¹ and relative standard deviations of the recoveries are below 10%. The performance of the proposed method was compared with those involving traditional liquid-liquid extraction (LLE) and solid phase extraction (SPE) on the real water samples (i.e., tap and well water as well as domestic and industrial wastewaters, etc.) and comparable efficiencies were obtained. The proposed USAEME procedure has been demonstrated to be viable, simple, rapid and easy to use for residue analysis of PCBs in water samples.     

Bioelectrochemical immunoassay of polychlorinated biphenyl

A simple, rapid, and highly sensitive bioelectrochemical immunoassay method based on magnetic beads (MBs) and disposable screen-printed electrodes (SPE) has been developed to detect polychlorinated biphenyls (PCBs). The principle of this bioassay is based on a direct competitive enzyme-linked immunosorbent assay using PCB-antibody-coated MBs and horseradish peroxidase (HRP)-labeled PCB (HRP-PCB). A magnetic process platform was used to mix and shake the samples during the immunoreactions and to separate free and unbound reagents after the liquid-phase competitive immunoreactions among PCB-antibody-coated MBs, PCB analyte, and HRP-PCB. After a complete immunoassay, the HRP tracers attached to MBs were transferred to a substrate solution containing o-aminophenol and hydrogen peroxide for electrochemical detection. The different parameters, including the amount of HRP-PCB conjugates, immunoreaction time, and the concentration of substrate that governs the analytical performance of the immunoassay have been studied in detail and optimized. The detection limit of 10 pg mL⁻¹ was obtained under optimum experimental conditions. The performance of this bioelectrochemical immunoassay was successfully evaluated with untreated river water spiked with PCBs, and the results were validated by commercial PCB enzyme-linked immunosorbent assay kit, indicating that this convenient and sensitive technique offers great promise for decentralized environmental application and trace PCBs monitoring.     

Development of a solid-phase extraction method for the determination of polychlorinated biphenyls in water

Polychlorinated biphenyls (PCBs) in water were extracted with a rebuilt extraction unit using 47 mm C18 solid-phase extraction (SPE) disks. Three types of disks (SPEC, ENVI and Empore) were investigated for the extraction of seven PCBs from 11 reagent water spiked at two concentration levels (20 and 1000 ng/l). The Empore disks produced the best analyte recoveries (91-107% with R.S.D. of 1-8%) at the low concentration level and displayed no leaking tendency. Empore disks were therefore considered superior to ENVI and SPEC disks for the conditions outlined in this work. The obtained extracts were dried and purified in an additional clean-up step using custom-made columns containing Florisil and Na2SO4. For water containing large amounts of organic matter, a pre-filtration was included. Final analysis was carried out on a dual-column GC-electron-capture detection system with on-column injection. The optimised extraction method, including clean-up, was less time-consuming and used less hazardous organic solvents than conventional liquid-liquid extraction (LLE) methods. Recoveries were 92-102% with R.S.D. of 3-8%.     

Determination of polychlorinated biphenyls by liquid chromatography–atmospheric pressure photoionization–mass spectrometry

This study presents the atmospheric pressure photoionization (APPI) of high‐chlorinated (five or more chlorine atoms) polychlorinated biphenyls (PCBs) using toluene as dopant, after liquid chromatographic separation. Mass spectra of PCB 101, 118, 138, 153, 180, 199, 206 and 209 were recorded by using liquid chromatography‐APPI‐tandem mass spectrometry (LC‐APPI‐MS/MS) in negative ion full scan mode. Intense peaks appeared at m/z that correspond to [M ? Cl + O]^? ions, where M is the analyte molecule. Furthermore, a detailed strategy, which includes designs of experiments, for the development and optimization of LC‐APPI‐MS/MS methods is described. Following this strategy, a sensitive and accurate method with low instrumental limits of detection, ranging from 0.29 pg for PCB 209 to 8.3 pg for PCB 101 on column, was developed. For the separation of the analytes, a Waters XSELECT HSS T3 (100 mm × 2.1 mm, 2.5 µm) column was used with methanol/water as elution system. This method was applied for the determination of the above PCBs in water samples (surface water, tap water and treated wastewater). For the extraction of PCBs from water samples, a simple liquid–liquid extraction with dichloromethane was used. Method limits of quantification, ranged from 4.8 ng l^?1, for PCB 199, to 9.4 ng l^?1, for PCB 180, and the recoveries ranged from 73%, for PCB 101, to 96%, for PCB 199. The estimated analytical figures were appropriate for trace analysis of high‐chlorinated PCBs in real samples. Copyright © 2014 John Wiley & Sons, Ltd.     

Combined protocol for the analysis of polycyclic aromatic hydrocarbons (PAHs) and polychlorobiphenyls (PCBx) from sediments using focussed microwave assisted (FMW) extraction at atmospheric pressure

A microwave-assisted protocol has been developed using focussed microwaves at atmospheric pressure for the extraction of PAHs and PCBs from sediments. It combines extraction and purification assisted by microwaves. This protocol has been applied to the quantification of 12 individual PAHs, 8 individual PCBs and 8 PCB coeluted mixtures from two Standard Reference Materials and one natural sediment. The results for both classes of compounds (PAHs and PCBs) are good in terms of recoveries, which are always greater than 70% and in most cases around 100%. The reproducibility is also good with coefficients of variation below 10% in most cases. This protocol has the great advantage of saving time, the time dedicated to the preparation / extraction assisted by microwaves being reduced to less than half an hour.     

Combined protocol for the analysis of polycyclic aromatic hydrocarbons (PAHs) and polychlorobiphenyls (PCBs) from sediments using focussed microwave assisted (FMW) extraction at atmospheric pressure

A microwave-assisted protocol has been developed using focussed microwaves at atmospheric pressure for the extraction of PAHs and PCBs from sediments. It combines extraction and purification assisted by microwaves. This protocol has been applied to the quantification of 12 individual PAHs, 8 individual PCBs and 8 PCB coeluted mixtures from two Standard Reference Materials and one natural sediment. The results for both classes of compounds (PAHs and PCBs) are good in terms of recoveries, which are always greater than 70% and in most cases around 100%. The reproducibility is also good with coefficients of variation below 10% in most cases. This protocol has the great advantage of saving time, the time dedicated to the preparation / extraction assisted by microwaves being reduced to less than half an hour.     

Simple solid-phase extraction method for determination of polychlorinated biphenyls and selected organochlorine pesticides in human serum

A simple off-line solid-phase extraction (SPE) method for isolation of polychlorinated biphenyls (PCBs) and selected organochlorine pesticides (OCPs) from human serum has been developed. The procedure includes denaturation of serum proteins by a mixture of water-1-propanol, application of the sample by aspiration twice repeatedly through the SPE column and elution with a mixture of n-hexane-dichlormethane. After final clean-up the compounds of interest were analysed by gas chromatography with micro-electron capture detection (GC-microECD). The recoveries achieved for PCB congeners using spiked porcine serum samples were 99-120% and for OCPs 88-115%. Relative standard deviations (RSD) ranged from 3 to 7%. The method was applied to real human serum samples and the recoveries of analytes in the serum were proportionally recalculated considering the recovery of the internal standard PCB-174. PCB-103 served as a syringe standard to correct volume of samples analysed. The aim of this study was to develop an effective off-line SPE procedure by optimization of existing SPE methods to supply laborious, solvent- and time-consuming liquid-liquid extraction (LLE) in routine analytical process.     

Clean-up methods for polycyclic aromatic hydrocarbons analyses by capillary gas chromatography

Summary Comparative results of pre-treatment methods for the extracts of polycyclic aromatic hydrocarbons (PAHs) from airborne particulate matter for quantitative determination by gas chromatography (GC) are presented. The first method included liquid-liquid extraction and column liquid adsorption chromatography. In the second procedure the extract was fractionated by liquid-liquid chromatography and liquid adsorption chromatography. In the last procedure two different solid phase extraction (SPE) cartridges examined makes it possible to separate PAHs and remove paraffinic compounds which is very important for the quantitative GC analysis of the PAHs. Recoveries of PAH standards and some their derivatives were determined and the contents of 15 of the most important PAHs, were compared. Presented at the 21^st ISC held in Stuttgart, Germany, 15^th–20^th September, 1996     

Solid-phase extraction clean-up procedure for the analysis of PAHs in lichens

A clean-up procedure based on a solid-phase extraction column was optimized for determination of polycyclic aromatic hydrocarbons (PAHs) in lichen extracts to remove co-extracted compounds from the matrix in the final extract. Several kinds of solid phases were evaluated: normal phase (-NH₂ and alumina), strong anion exchange and reversed phase. The -NH₂ columns were the most effective by using a packed solid bed of 500?mg. The lichen raw extract was loaded on the column previously conditioned with dichloromethane and hexane. Hexane (0.5?mL) was used as rinsing solvent, and PAHs were quantitatively eluted (80–97%) using 2?mL of hexane–dichloromethane (65–35) as eluting solvent. In these conditions, even the heaviest PAHs were quantitatively eluted. The optimized SPE method provides a short time and low-solvent-consumption sample clean-up compared with other conventional methods based on column chromatography. The analytical procedure, dynamic sonication-assisted extraction, followed by the optimized solid-phase extraction clean-up, was used to determine the 16 EPA priority PAHs from native lichens collected from the Aragon valley in central Pyrenees. The PAH concentrations in lichen samples ranged from 352 to 1654?ng?g^?1, and the minimum concentration value was established as the regional reference PAH levels in the area.     

Quantification of volatile PAHs present at trace levels in air flow by aqueous trapping—SPE and HPLC analysis with fluorimetric detection

In the context of a European project, a new approach of sampling of volatile polycyclic aromatic hydrocarbons (PAHs) from air was developed. In fact, the aim of this project was to test the efficiency of an air cleansing prototype reactor, which was operating by non-thermal plasmolysis. With an eye to model the atmosphere ejected by the prototype, we needed to vaporise the volatile PAHs in an air stream at concentrations as low as those recommended by European Directives (96/62/CE) for PAHs in ambient air (i.e. 1 ng m⁻³). Our strategy was based on the analysis of PAHs trapped in an aqueous medium, in order to avoid important losses of volatile compounds observed during the delicate desorption-concentration step when classical solid supports are used. Then a study was carried out to determine: the design of the collecting part, the flow-rate of the air sampling, the nature and concentration of chemical additives used to enhance PAH solubility in water. The very highly diluted aqueous media obtained after the bubbling step were concentrated by solid-phase extraction (SPE) on hydrophobic cartridges and analysed on-line by reversed-phase HPLC with UV and fluorimetric detections. Lastly, the sampling technique was directly applied to the outlet of the air cleansing prototype and the analysis after 3-6 h of non-thermal plasmolysis showed that the target volatile PAHs were not present in an air stream initially polluted by volatile organic compounds.