掺杂稀土离子晶体中的电磁感应光透明现象

对在掺杂稀土离子晶体中实现电磁感应光透明进行了实验研究。首先,以Er3＋∶YAG晶体为样品,用旋转波近似下的密度矩阵方程理论计算了探测场的吸收特性随Er3＋离子浓度的变化规律,结果表明：在探测场失谐Δp=0时,形成了一个对于探测光透明的窗口,从而在理论上论证了在掺杂稀土离子晶体中实现电磁感应光透明效应的可行性。设计了一个以Pr3＋∶Y2SiO5晶体为样品的实验激发方案,吸收光谱显示,当温度为6 K时其在共振吸收峰处可形成一个完全透明的窗口,实现了在掺杂离子晶体中的电磁感应光透明。实验还分析了工作温度、耦合场失谐对探测光透过率的影响,结果显示：当样品温度上升到15 K时,透明窗口消失;耦合场的失谐量越大,透射率越小。     

YAG晶体中Tm^3＋离子的荧光特征分析

计算了ＹＡＧ晶体中Ｔｍ＾３＋离子辐射跃迁几率Ａｉｊ，无辐射跃迁几率Ｗｉｊ，交叉弛豫几率Ｐ，荧光寿命τｉ和荧光分支比βｉｊ等荧光特征参量，并利用这些值及跃迁速率方程讨论了＾３Ｆ４能级荧光强度与掺杂浓度的关系，得出当激发光的泵浦速率从１０＾２～１０＾６ｓ＾－１时，Ｔｍ＾３＋离子的最佳相对浓度Ｘｏｐ在４．９～６．４％之间。     

YAG晶体中Ce^3＋对Er^3＋的敏化作用

通过求解（Ｃｅ，Ｅｒ）：ＹＡＧ和Ｅｒ：ＹＡＧ的能级跃迁速率方程，讨论了Ｃｅ＾３＋对Ｅｒ＾３＋离子的敏化作用。表明掺Ｃｅ＾３＋可增强Ｅｒ＾３＋离子１．６６μｍ波长的激光强度，但仅改变了１．６６μｍ波长激光粒子数反转，即Ｎ２（＾４Ｉ１２／２）〉Ｎ１（＾４Ｉ１５／２）与Ｅｒ＾３＋离子浓度的关系。     

Er：YLF晶体中Er^3＋离子的光谱特征

利用居地－奥非脱（Ｊｕｄｄ－Ｏｆｅｌｔ）理论计算了Ｅｒ＾３＋离了在氟化钇锂（ＬｉＹＦ４简写为ＹＬＦ）晶体中的辐射跃迁几率Ａｊｊ无辐射跃迁几率ωＪＪ及激发态荧光寿命τ，并根据荧光动力学方程计算出各激发态布居数ＮＪ与掺杂浓度ｘ的关系，对２．７μｍ激光（＾４Ｉ１１／２→＾４Ｉ１３／２）来说，掺杂浓度要大于～３ａｔ％，才能实现布居数反转，对波长为１．７３μｍ的＾４Ｉ１３／２→＾４Ｉ１５／２跃迁，存在荧光强     

Role of amorphous silicon domains of Er^3＋ emission in the Er—doped hydrogenated amorphous silicon suboxide film

An investigation on the correlation between amorphous Si (a-Si) domains and Er^{3+} emission in the Er-doped hydrogenated amorphous silicon suboxide (a-Si:O:H) film is presented. On one hand, a-Si domains provide sufficient carriers for Er^{3+} carrier-mediated excitation which has been proved to be the highest excitation path for Er^{3+} ion; on the other hand, hydrogen diffusion from a-Si domains to amorphous silicon oxide (a-SiO_x) matrix during annealing has been found and this possibly decreases the number of nonradiative centres around Er^{3+} ions. This study provides a better understanding of the role of a-Si domains on Er^{3+} emission in a-Si:O:H films.     

相干驱动场的线宽对电磁感应透明的影响

考虑相干驱动场的线宽，探讨了其对双激发态原子三能级系统中的电磁感应透明现象的影响，得到结论：相干驱动场的线宽抑制了介质对弱探测光的透明。     

掺Er^3＋离子Sr3Y2（BO3）4晶体光谱性能的研究

研究了提拉法生长的掺Er^3＋的Sr3Y2（BO3）4晶体的吸收光谱和荧光光谱。应用J—O理论分析并计算了光谱参数,得到唯象参数Ω2、Ω4和Ω6分别为11．90×10^-20cm^2、3．44×10^-20cm^2和1．92×10^-20cm^2。在Er^3＋：Sr3Y2（BO3）4晶体中,Er^3＋在1533nm波长的发射截面为1．00×10^-20cm^2,^4I13／2→^I15／2能级跃迁的荧光寿命和辐射寿命分别为0．58ms和4．10ms,良好的光谱性能表明Er^3＋：Sr3Y2（BO3）4晶体可能成为潜在的1．55μm波段的一种激光材料。     

Ce^3＋离子敏化Eu^3＋：Cr^3＋：Sm^3＋：YAG外延层的荧光现象

对Ce^3 :Eu^3 :Cr^3 :Sm^3 :YAG外延层中的荧光敏经现象进行了报道和分析，在较高浓度的Ce^3 离子掺杂时，外处层在蓝色、绿色波段出现了新的荧光谱线，可解释为在Ce^3 离子每化作用下，Eu^3 离子产生了由高位激发态能级^5Di(i=1,2,3）直接到基态能级^7Fj(j=0,1,2,3）的辐射跃迁过程，并且这种Ce^3 :Eu^3 :Cr^3 :Sm^3 :YAG外延层还是一种新颖的白色单晶荧光材料。     

温度对晶体中稀土离子(E)-型能级电磁感应透明的影响

运用产经典理论，在Pr^3 ：YSO晶体Pr离子E－型三级级系统中，求解了探测光吸收在不同光跃迁驰豫速率与自旋跃迁驰豫速率下的瞬态及稳态解，得到了电磁感应透明现象，分析了两种驰豫对电磁感应透明的,人而揭示了掺稀土离子晶体中电磁感应透明对温度的依赖性。     

Influence of doping the pump-chamber material in a flashlamp pumped Er:YAG laser

The influence of the conversion of pump light of wavelengths below 400 nm into pump light with a central wavelength of 500 nm in a Europium doped quartzglass pump chamber has been investigated. The results are compared to the ones from an undoped quartzglass. The measurements resulted in a reduction of the slope efficiency by a factor of two for the doped quartzglass compared to the undoped one. Furthermore, the pump-pulse lengths around 80 μs lead to a decrease in the slope efficiency compared to pump-pulse lengths above 100 μs.     

Er3+:YVO4中Er3+的光谱参数计算

根据掺杂Er3+(0.5%)的YVO4样品的吸收光谱,用Jubb-Ofelt理论拟合出唯象强度参最Ωλ,并由此计算了激发能级的振子强度、自发辐射跃迁速率、荧光分支比和积分发射截面等光谱参量.并根据这些光学参量,分析了Er3+:YVO4晶体的应用价值.其中,特别是4I13/2→4I15/2, 2H11/2→4I15/2, 4S3/2→4I15/2和4F9/2→4I15/2等几个强发光能级具有较大的振子强度(大于10-6)和积分发射截面(大于10-18cm),分别分析了它们的应用前景,因此非常值得关注.并且,本文结果和Capobianco等所报道的Er3+(2.5 mol%):YVO4晶体强度参量结果很相近.而且,通过比较掺Er3+钒酸钇晶体和掺Er3+其他晶体的光学性能,可以看出钒酸钇晶体作为激光晶体的优点.最后,还根据Er3+在晶体中的对称性,利用群论讨论了Er3+在YVO4晶场中各能级的劈裂情况.     

Er3+:GdVO4中Er3+离子的光谱参数计算和晶场中能级分裂的讨论

对Er3+:GdVO4样品的光谱参数以及Er3+在晶场中能级的分裂情况进行了研究.首先对样品进行了吸收光谱的测量,接着用Judd-Ofelt理论拟合出了Er3+在GdVO4晶体中的强度参量Ωt,并由此计算了跃迁的振子强度、自发辐射跃迁速率、荧光分支比和积分发射截面.通过计算结果可以发现有较多能级之间的跃迁都有大于10-6的振子强度和大于10-18 cm的积分发射截面,并且具有较高的荧光分支比,特别是2H11/2→4I15/2,4S3/2→4I15/2,4F9/2→4I15/2和4I13/2→4I15/2等几个强发光能级除了具有较大的振子强度和积分发射截面外还有很好的应用前景,因此也更加值得关注.最后还利用群论讨论了Er3+离子在GdVO4晶场中各能级的分裂情况并对各Stark子能级的Jz混杂情况进行了分析.     

Er,Yb:YAG微晶玻璃发光特性的研究

高温熔制Er³⁺，Yb³⁺离子掺杂CaO-Y₂O₃-Al₂O₃-SiO₂系统玻璃，并进行微晶化处理，研究了微晶玻璃中Er³⁺离子的发光及上转换发光特性，分析了微晶玻璃上转换发光机理.结果表明：原始玻璃经热处理得到了Er,Yb:YAG微晶玻璃，微晶玻璃中Er³⁺离子在室温下⁴I_13/2→⁴I_15/2跃迁产生横盖1450—1650nm区间的超宽带荧光，荧光半高宽达180nm，这可能由于YAG微晶相中Er³⁺离子与玻璃相中残留Er³⁺离子的共同发光；Er³⁺与Yb³⁺离子局域基质声子能量的降低使微晶玻璃Er³⁺离子上转换发光强度与原始玻璃相比显著提高，绿光、红光上转换荧光强度比玻璃样品分别增强约7和3倍；微晶化后Er³⁺，Yb³⁺离子局域环境发生变化也导致微晶玻璃中Er³⁺离子绿光、红光上转换发光相对强度发生变化. 关键词： 铒 镱:钇铝石榴石 微晶玻璃 荧光光谱     

Er~(3+)∶YVO_4的频率上转换动力学分析

测量并分析了980nm抽运下Er3+∶YVO4晶体的上转换荧光,建立了描述Er3+离子跃迁的速率方程。通过求解速率方程并拟合1550nm,980nm和550nm的荧光衰减实验曲线,得到了4I13/2+4I13/2→4I15/2+4I9/2,4I11/2+4I11/2→4I15/2+4F7/2的频率上转换系数C22=9.221×10-17cm3s-1,C33=7.545×10-17cm3s-1。通过测量980nm抽运下的550nm荧光衰减谱,得到了4S3/2能级的主要上转换机制是以激发态吸收为主。     

Highly oriented crystalline Er:YAG and Er:YAP layers prepared by PLD and annealing

High quality, thick, highly oriented crystalline thin films of Yttrium Aluminum Garnet (Y₃Al₅O₁₂) and Yttrium Aluminum Perovskite (YAlO₃) doped with Erbium were prepared by pulsed laser deposition. Samples were created in vacuum or oxygen environment. Depositions were arranged at room temperature, or at high substrate temperatures ranging from 800 to 1100 °C. Amorphous layers were annealed by laser, or in oven (argon flow, temperatures in range from 1200 to 1400 °C). Fused silica and sapphire (0 0 0 1) were used as substrates. Properties of films were characterized by X-ray diffraction, atomic force microscopy, and by photoluminescence measurement. Size of crystalline grains was in the range 116-773 nm. Thickness of layers was up to 17 μm.     

Er3+及Er3+/Yb3+共掺铋酸盐玻璃光谱性质研究

制备了Ed3+及Ed3+/Yb3+共掺铋酸盐玻璃,测试了样品的吸收光谱、荧光光谱.应用Judd-Oflet理论计算了Er3+在铋酸盐玻璃中的光谱强度参数,分别为Ω2=(5.47-2.92)×10-20cm2,Ω4=(2.16-1.22)×10-20cm2,Ω6=(1.29-0.80)×10-20cm2.比较了Er3+及Er3+/Yb3+共掺铋酸盐玻璃在980 nm附近的吸收截面和1.5μm的荧光发射光谱强度,Er3+/Yba+共掺铋酸盐玻璃的荧光光谱半高宽达到91 nm,比Er3+单掺铋酸盐玻璃大15 nm.用McCumber理论计算了Ed3+在1.5 μm的受激发射截面σe=1.00×10-20cm2.比较了Ed3+在不同基质中的光谱特性,结果表明铋酸盐玻璃更适合作为掺铒光纤放大器的基质材料.     

Effect of Er:YAG laser energy on the morphology of enamel/adhesive system interface

The aim of this study was to evaluate in vitro the influence of Er:YAG laser energy variation to cavity preparation on the morphology of enamel/adhesive system interface, using SEM. Eighteen molars were used and the buccal surfaces were flattened without dentine exposure. The specimens were randomly assigned to two groups, according to the adhesive system (conventional total-etching or self-etching), and each group was divided into three subgroups (bur carbide in turbine of high rotation, Er:YAG laser 250 mJ/4 Hz and Er:YAG laser 300 mJ/4 Hz) containing six teeth each. The enamel/adhesive system interface was serially sectioned and prepared for SEM. The Er:YAG laser, in general, produced a more irregular adhesive interface than the control group. For Er:YAG laser 250 mJ there was formation of a more regular hybrid layer with good tag formation, mainly in the total-etching system. However, Er:YAG laser 300 mJ showed a more irregular interface with amorphous enamel and fused areas, for both adhesive systems. It was concluded that cavity preparation with Er:YAG laser influenced on the morphology of enamel/adhesive system interface and the tissual alterations were more evident when the energy was increased.     

Robust hollow devices and waveguides for Er:YAG laser radiation

Fluorocarbon-polymer (FCP) coated silver hollow stainless steel (St) devices and waveguides have been developed for Er:YAG laser radiation. Full liquid phase techniques have been adopted to coat the silver and FCP layers inside the stainless steel hollow structure. Both straight and bent robust hollow devices have been fabricated as the output optical elements for the delivery system of medical Er:YAG lasers. A robust hollow waveguide with the length of about 1.6 m has also been realized as an actual delivery system.