碳糊电极吸附溶出伏安法测定游离钙

基于Ca(Ⅱ)-茜素红S(ARS)络合物在碳糊电极上的还原波,建立了吸附溶出伏安测定游离钙的新方法。在1.5×10-2mol/LKOH-2.0×10-5mol/LARS介质中,Ca(Ⅱ)-ARS络合物在碳糊电极上于-0.89V处产生一吸附还原波。当富集电位为.0.1V,富集时间90s,扫描速度为100mV/s时,该络合物单扫描阴极溶出峰的二阶导数峰电流与游离钙离子浓度在3.0×10-8~2.0×10-6mol/L范围内呈线性关系;检出限为9.4×10-9mol/L。在0.2mol/LHCl中清洗2min,该电极重现性良好。该方法可用于血清、牛奶和自来水中游离钙的测定。     

阴极溶出伏安法测定异烟肼的研究

报道了吸附阴极溶出伏安法测定异烟肼。探讨了电极反应机理。在０．０１ｍｇｏｌ／Ｌ硼砂底液中，峰电位为－１．４０Ｖ。峰电流与异烟肼浓度在４．０＊１０＾－７－１．５＊１０＾－５ｍｏｌ／Ｌ范围内呈良好的线性关系，相关系为０．９９１３。该方法用于异烟肼片剂的测定，获得满意结果。     

杯芳烃修饰玻碳电极吸附溶出伏安法测定微量铅

研究了以杯芳烃衍生物修饰玻碳电极,以其吸附溶出伏安法测定微量铅。对富集时间、铅的浓度、支持电解质、样品溶液pH值及部分离子干扰等进行了实验。实验发现以氢氧化钠溶液处理修饰电极可提高测定灵敏度,经过优化处理后,线性范围和检出限分别为5.0×10-7～1.0×10-5mol/L和1.0×10-8mol/L。应用本法对合成水样进行了测定,结果满意。本文还对吸附溶出机理进行了讨论。     

固体石蜡作粘合剂的纯碳糊电极的电化学活化及其应用于色氨酸的测定

研究了以固体石蜡作粘合剂的纯碳糊电极的电化学活主用于色氨酸直接测定的方法。活化后的电极对色氨酸的吸附能力大大增加，在ＨＡｃ－ＮａＣ溶液中，于＋０．３Ｖ富集后，于＝１．０１Ｖ出峰，用线扫伏安法测定时，二次微分溶电流，与色氨酸浓度在８－１０μｇ／Ｌ范围内成线性；检测限可达２μｇ／Ｌ；２倍的酪氨酸和其它氨基酸不干扰，用于氨基酸酸芭物样品和合成血清样品中色氨酸的测定，相对标准偏差小于２％。     

Adsorptive Stripping Voltammetric Detection of Single‐Stranded DNA at Electrochemically Modified Glassy Carbon Electrode

Electrochemically modified glassy carbon electrode (GCE) was used to study the electrochemical oxidation and detection of denatured single‐stranded (ss) DNA by means of adsorptive stripping voltammetry. The modification of GCE, by electrochemical oxidation at +1.75 V (vs.SCE) for 10 min and cyclic sweep between +0.3 V and ?1.3 V for 20 cycles in pH 5.0 phosphate buffer, results in 100‐fold improvement in sensitivity for ssDNA detection. We speculated that the modified GCE has a high affinity to single‐stranded DNA through hydrogen bond (specific static adsorption). Single‐stranded DNA can accumulate at the GCE surface at open circuit and produce a well‐defined oxidation peak corresponding to the guanine residues at about +0.80 V in pH 5.0 phosphate buffer, while the native DNA gives no signal under the same condition. The peak currents are proportional to the ssDNA concentration in the range of 0–18.0 μg mL^?1. The detection limit of denatured ssDNA is ca. 0.2 μg mL^?1 when the accumulation time is 8 min at open circuit. The accumulation mechanism of ssDNA on the modified GCE was discussed.     

槲皮素化学修饰碳糊电极吸附溶出伏安法测定痕量铅

建立了用槲皮素修饰碳糊电极测定痕量铅的新方法 ,在 0 .1 0mol L甲酸盐缓冲液 (pH 4.3 )中 ,于 -0 .1 0V(vs.SCE)搅拌富集 ,再在 -0 .70V静止还原 40s后 ,阳极化扫描 ,于 -0 .42V左右获得一灵敏的铅阳极溶出峰。在最佳条件下 ,富集不同时间 ,其二次导数峰电流与Pb2 + 在 1 .0× 1 0 - 8～ 8.0× 1 0 - 7mol L和 2 .0× 1 0 - 9～ 6.0× 1 0 - 8mol L两个范围内呈线性关系 ,检出限为 8.0× 1 0 - 1 0 mol L(S N =3 )。同时初步探讨了电极反应机理。     

Carbon Paste Electrode Plated with Lead Film. Voltammetric Characteristics and Application in Adsorptive Stripping Voltammetry

A lead film plated in situ at a carbon paste support was tested as a novel, potential electrode for adsorptive stripping voltammetric determination of cobalt traces in an ammonia buffer solution. To show the practical applicability of the new electrode, a catalytic adsorptive Co system in a supporting electrolyte containing 0.1 M ammonia buffer, 5×10^?4 M nioxime and 0.25 M nitrite was selected and investigated as a model solution. Pb and Co ions were simultaneously accumulated in situ on the electrode surface: Pb ions electrochemically at ?1.3 V) and then at ?0.75 V, at which potential the Co(II)‐nioximate complex was also pre‐concentrated via adsorption. Instrumental parameters, such as the time of nucleation and formation of Pb film deposits, the time of accumulation of the Co‐nioxime complex at the PbF/CPE, and the procedures of electrode regeneration, were optimized to obtain good reproducibility and sensitivity of the Co response. The optimized procedure yields favorable and highly stable stripping responses with good precision (RSD=3% for a 5×10^?8 M Co) and good linearity (up to 5×10^?7 M, coefficient of determination, R=0.996). The detection limit was 4×10^?10 M Co (0.023 μg L^?1) for an accumulation time of 120 s. The method enables the determination of Co in the presence of high excesses of Ni or Zn. The voltammetric data were correlated with the structural characterization by scanning electron microscopy (SEM) and X‐ray fluorescence spectroscopy (XRF).     

Catalytic Adsorptive Stripping Voltammetry at a Carbon Paste Electrode for the Determination of Amiodarone

Voltammetry using solid electrodes usually suffers from the contamination due to the deposition of the redox products of analytes on the electrode surface. The contamination has resulted in poor reproducibility and overelaborate operation procedures. The use of the chemical catalysis of oxidant on the reduction product of analyte not only can eliminate the contamination of analyte to solid electrodes but also can improve the faradaic response of analyte. This work introduced both the catalysis of oxidant K2S2O8 and the enhancement of surfactant Triton X-100 on the faraday response of amiodarone into an adsorptive stripping voltammetry at a carbon paste electrode for the determination of amiodarone. The method exhibits high sensitivity, good reproducibility and simple operation procedure. In 0.2 mol·L^-1 HOAc-NaOAc buffer （pH=5.3） containing 2.2×10^-2 mol·L^-1 K2S2O8 and 0.002% Triton X-100, the 2.5th-order derivative stripping peak current of the catalytic wave at 0.3 V （vs. Ag/AgCl） is rectilinear to amiodarone concentration in the range of 2.0×10^-10-2.3×10^-8 mol·L^-1 with a detection limit of 1.5×10^-10 mol·L^-1 after accumulation at 0 V for 30 s.     

碳糊电极阳极吸附伏安法测定环丙沙星

报道了用碳糊电极阳极吸附伏安法测定环丙沙星的新方法.在 0. 40mol/L的NH4Ac HAc(pH4. 30)缓冲液中,使用JP 303极谱分析仪,环丙沙星在碳糊电极 (CPE)上有一灵敏的吸附伏安氧化峰,峰电位为1. 12V(vs.SCE).该氧化峰的二阶导数峰电流与环丙沙星的浓度在 8. 0×10-9 ~8. 0×10-7 mol/L(富集 90s)范围内成良好的线性关系,相关系数为 0. 998 8,检出限为 4. 0×10-9 mol/L(S/N=3,富集 110s).探讨了环丙沙星在碳糊电极上的伏安性质和电极反应机理,并且成功应用于人体尿样中环丙沙星含量的测定.加入回收实验,回收率在95. 5%至 103. 9%之间.     

碳糊电极阳极吸附伏安法测定氧氟沙星

碳糊电极阳极吸附伏安法测定氧氟沙星;氧氟沙星; 阳极吸附伏安法; 碳糊电极     

玻碳电极吸附伏安法测定痕量硫化物的研究

研究了利用玻碳电极吸附伏安法测定痕量硫化物的新方法。在含高铁离子的酸性溶液中,硫化物与对-氨基苯二甲基盐酸盐(p-ADAD)反应生成亚甲基蓝,采用线性扫描伏安法亚甲基蓝于-0.30 V(vs.SCE)在玻碳电极上出现灵敏的还原峰,峰电流与S2-浓度在0～25μg/mL范围内呈良好的线性关系。优化了实验条件,研究了电极反应机理。该方法具有灵敏、简便、快速、避免汞污染等特点。已成功用于多种水样中痕量硫化物的测定,回收率为98.0%～104.6%,结果令人满意。     

Highly Sensitive and Selective Adsorptive Stripping Voltammetric Method Employing a Lead Film Screen‐printed Electrode for Determination of Cobalt as its Nioximate Complex

A carbon screen‐printed electrode modified in‐situ with lead film (PbF‐SPCE) was applied for the adsorptive stripping voltammetric determination of Co(II) in the form of a complex with 1,2‐cyclohexanedione dioxime. Lead film was electrochemically deposited in situ on SPCE from a 0.2 M ammonia buffer solution (pH 8.7) containing 5 ? 10^?5 M Pb(NO₃)₂ and 5 ? 10^?5 M nioxime. Due to the very low LOD (0.003 µgL^?1, i.e., 0.05 nmol L^?1 Co(II); t_acc=120s), the developed procedure could be rated among the most sensitive methods employing SPEs. The Ni(II) signal was significantly lower than the Co(II) one and the separation of Ni(II) and Co(II) peaks was even better at the PbF‐SPCE than at the hanging mercury drop electrode.     

Adsorptive Cathodic Stripping Voltammetric Method for Determination of Gallium Using an In Situ Plated Lead Film Electrode

The in situ plated lead film electrode was proposed for the first time for adsorptive stripping voltammetric determination of gallium in water samples. The method was based on simultaneous lead film formation and Ga(III)‐cupferron complex preconcentration at ?0.7 V and its cathodic stripping during the potential scan. The composition of the supporting electrolyte, cupferron concentration, conditions of lead film formation, potential and time of accumulation were studied in detail. Under optimum conditions the limit of detection was 3.8×10^?9 mol L^?1. The proposed procedure was validated in the course of Ga(III) determination in waste water certified reference materials.     

Adsorptive Stripping Voltammetric Measurements of Trace Molybdenum at the Bismuth Film Electrode

Bismuth‐film electrodes on glassy‐carbon substrates have been successfully applied for adsorptive‐stripping voltammetric measurements of trace molybdenum in the presence of chloranilic acid (CAA). The procedure is based on the preconcentration of the molybdenum‐chloranilic acid complex at a preplated bismuth film electrode held at ?0.55 V (vs. Ag/AgCl), followed by a negatively‐sweeping square‐wave voltammetric scan. Factors influencing the adsorptive stripping performance, including different ligands, solution pH, CAA concentration, preconcentration time and potential, have been optimized. The response compares favorably with that observed at mercury film electrodes, and is linear over the 5–50 μg/L Mo concentration range (one min preconcentration). A detection limit of 0.2 μg/L molybdenum is obtained following a 10 min accumulation. High stability is indicated from the reproducible response of a 100 μg/L molybdenum solution (n= 60; RSD=2.6%). Applicability to seawater samples is demonstrated.     

Adsorptive Stripping Voltammetric Determination of Albendazole at a Hanging Mercury Drop Electrode

ABSTRACT

Albendazole is determined by differential-pulse adsorptive cathodic stripping voltammetry at a hanging mercury drop electrode using the reduction peak of its copper(II) complex at ?0.28V at an accumulation potential 0.0V vs. Ag/AgCl electrode. The optimum conditions of pH, accumulation potential and accumulation time were studied. The calibration graph for the determination of albendazole was linear in the range 3.0X10^?8 - 9X10^?7M with a relative standard deviation of 2.8%. The detection limit was 1.0X10^?8M after 180s accumulation at 0.0V. The effect of common excipients and metal ions on the peak height of albendazole was studied. The presence of Cu²⁺ ions forms a stable complex with albendazole which is strongly adsorbed at the mercury electrode surface. The method was applied to the determination of the drug in commercially available dosage forms.     

Simultaneous Adsorptive Cathodic Stripping Voltammetric Determination of Nickel(II) and Cobalt(II) at an In Situ Bismuth‐Modified Gold Electrode

A study on the simultaneous determination of Ni(II) and Co(II) dimethylglyoximates (Ni‐DMG and Co‐DMG) through adsorptive cathodic stripping voltammetry at an in situ bismuth‐modified gold electrode (Bi‐AuE) is reported. The key operational parameters, such as Bi(III) concentration, accumulation potential and accumulation time were optimized and the morphology of the Bi‐microcrystals deposited on the Au‐electrode was studied. The Bi‐AuE allowed convenient analysis of trace concentrations of solely Ni(II) or of Ni(II) and Co(II) together, with cathodic stripping voltammograms characterized by well‐separated stripping peaks. The calculated limit of detection (LOD) was 40 ng L^?1 for Ni(II) alone, whereas the LOD was 98 ng L^?1 for Ni(II) and 58 ng L^?1 for Co(II), when both metal ions were measured together. The optimized method was finally applied to the analysis of certified spring water (NIST1640a) and of natural water sampled in the Lagoon of Venice. The results obtained with the Bi‐AuE were in satisfactory agreement with the certified values and with those provided by complementary techniques, i.e., ICP‐OES and ICP‐MS.     

Square Wave Adsorptive Stripping Voltammetric Determination of Cyromazine Insecticide with Multi-Walled Carbon Nanotube Paste Electrode

The electrochemical behavior of cyromazine (N-cyclopropyl-1,3,5-triazine-2,4,6 triamine) insecticide has been studied at newly prepared multi-wall carbon nanotubes paste electrodes using square wave stripping voltammetry. The cyromazine was accumulated at 0.0 mV [vs. Ag/AgCl (3 M NaCl)] and a well-defined anodic peak obtained at +1110 mV in 0.1 M H₂SO₄. The cyclic voltammetric measurements showed an irreversible nature of oxidation wave in the range of scan rates comprised between 500 and 4000 mV s^?1. The calibration curve obtained from square wave stripping voltammetry was linear in the range 0.41 to 83.30 µg/mL with a detection limit of 0.12 µg/mL. The method was applied to the direct determination of cyromazine in natural water samples. Recoveries calculated for river and tap water samples spiked with 10.0 µg/mL level were 101.5 ± 1.9% and 100.6 ± 2.3% at 95% confidence level, respectively. The method was extended to the determination of cyromazine in agrochemical formulation Trigard® with a recovery of 100.49% and accuracy was in agreement with that obtained by HPLC comparison method. Influences of some interfering ions and pesticides were also investigated.     

邻苯三酚红修饰碳糊电极吸附伏安法测定痕量铋

报道了采用邻苯三酚红修饰碳糊电极测定痕量铋的方法。在０．３０ｍｏｌ／Ｌ的ＨＣｌ溶液中,于－０．１０Ｖ搅拌富集３ｍｉｎ,然后在－０．３５Ｖ静止还原６０ｓ,再进行阳极化扫描,在－０．１０Ｖ左右获得灵敏的铋溶出峰,二次导数民流与铋浓度在１．０＊１０＾－９－６．０＊１０＾－７ｍｏｌ／Ｌ范围内呈线性关系,同限为５＊１０＾－１０ｍｏｌ／Ｌ。对电极反应机理进行了讨论。     

Cathodic and Adsorptive Stripping Votammetry of Naftazone

Abstract

Naftazone (1,2-naphthoquinone-2-semicarbazone) undergoes a reversible two-electron transfer in both acidic and alkaline solutions and also gives rise at pH > 7 to an anodic wave attributed to the formation of a mercury derivative. Cathodic stripping voltammetry is proposed to determine the compound down to 5 × 10^?9 M after accumulation of its mercury salt formed at -0.05V in a 0.05M sodium hydroxide solution. These results have been compared with those obtained by performing an adsorptive collection of the drug in a pH 3 sodium perchlorate solution. Concentrations ranging from 1 × 10^?7 to 2 × 10^?7M can be easily investigated, the detection limit being 7 × 10^?11M. The influence of several operational parameters has also been considered.     

固态汞合金电极吸附伏安法测定酪氨酸

采用白合金粉与汞混合制成汞合金糊,涂布在固体石蜡碳糊电极表面,固化后制得固态汞合金电极,并首先应用于酪氨酸的测定。在含Co2 的pH 9.2的硼砂-NaOH底液中,用线性扫描伏安法在-0.80~-1.30V范围内进行扫描,酪氨酸于-1.05 V出现灵敏的还原峰,酪氨酸的浓度与峰电流在1.0×10-7~1.0×10-5mol/L范围内呈线性关系。该法已用于复方氨基酸注射液中酪氨酸含量的测定,加标回收率达96%~102%。该电极既保留了汞电极的优点,又避免了汞电极有毒、使用不方便的缺点。