Alternative method for measurement of albumin/creatinine ratio using spectrophotometric sequential injection analysis

A simple, automatic and practical system for successive determination of albumin and creatinine has been developed by combining sequential injection analysis (SIA) and highly sensitive dye-binding assays. Albumin detection was based on the increase in the absorbance due to complex formation between albumin and eosin Y in acidic media. The absorbance of the complex was monitored at 547 nm. For the creatinine assay, the concentration of creatinine was measured by reaction with alkaline picrate to form a colored product which absorbs at 500 nm. The influences of experimental variables such as effects of pH, reagent concentration, standard/sample volume and interferences were investigated. Under optimal conditions, the automated method showed linearity up to 20 mg L⁻¹ for albumin and 100 mg L⁻¹ for creatinine. The 3σ detection limits were 0.6 and 3.5 mg L⁻¹ for albumin and creatinine, respectively, and the relative standard deviations (n = 10) were 2.49% for 20 mg L⁻¹ albumin, and 3.14% for 20 mg L⁻¹ creatinine. Application of the proposed method to the direct analysis of urinary samples yielded results which agreed with those obtained from the Bradford protein assay and a creatinine enzymatic assay according to a paired t-test. The results obtained should be a step towards developing a fully automated and reliable analytical system for clinical research, which requires direct determination of albumin and creatinine and/or its ratios.     

Using sequential injection analysis for fast determination of phosphate in coastal waters

A sequential injection analysis system (SIA) is described which is suited for the fast determination of filterable molybdate reactive phosphate (FRP, 0.2 μm) in coastal waters. It processes up to 270 samples per hour with a detection limit (3σ) of 0.05 μM and is used for surface mapping of phosphate in areas with steep concentration gradients like the Wadden Sea. The determination is based on the reaction of phosphate with acidic molybdate to phosphomolybdate, which builds non-fluorescent ion pairs with rhodamine 6G. The remaining rhodamine fluorescence is detected at 550 nm with an excitation at 470 nm. Syringe pump, valve and detector were controlled by a self made python programme, which was optimised for high speed SIA measurements in monitoring applications.     

Immunosensor for the determination of azidothymidine: its utilization as detector in a sequential injection analysis system

An amperometric immunosensor based on graphite paste (graphite powder and paraffin oil) has been constructed for the assay of azidothymidine (AZT). The graphite paste is impregnated with anti-AZT. The immunosensor can be reliably used for the assay of AZT in its pharmaceutical formulation. The potential used for AZT assay was 435 mV vs Ag/AgCl electrode. The surface of the immunosensor can be regenerated by simply polishing, obtaining fresh immunocomposite ready to be used in a new assay. Due to its reliability, the immunosensor was successfully used as a detector in a sequential injection analysis system, and gave reliable results for on-line assay of AZT purity in raw material and AZT contents in pharmaceutical formulations.     

Spectrofluorimetric determination of aluminum in drinking waters by sequential injection analysis

A selective procedure for the determination of Al³⁺ in drinking and natural waters is proposed. The analytical procedure is based both on the complex formation between Al³⁺ and 8-hydroxyquinoline-5-sulfonic acid (HQS) and on a fluorimetric detection of the complex. The reaction was carried out in presence of thioglycolic acid as a masking agent. This procedure has been adapted to a sequential injection analysis (SIA) system. Operative conditions both for batch and SIA procedures were investigated including reagent concentration, volumes, pH and wavelengths used for the fluorimetric detection. Batch procedure allows determination of Al³⁺ at ppb level (LOQ: 2.8 μg l⁻¹) within a working range of 2.2-300 μg l⁻¹. The SIA procedure was successfully employed for the determination of Al³⁺ in several commercial drinking and tap waters.     

顺序注射催化动力学光度法测定织物和室内空气中痕量甲醛

在磷酸介质中 ,甲醛可以催化溴酸钾氧化　花青的反应使其退色 ,据此建立了顺序注射催化动力学光度法测定织物和室内空气中痕量甲醛的新方法。方法的线性范围 0 .5～ 7.0 μg mL ,检出限 0 .1 μg mL。用于树脂整理特殊织物和室内空气中痕量甲醛的测定 ,回收率在 97.0 %～ 1 0 5 .0 %之间。     

The development of sequential injection analysis coupled with lab-on-valve for copper determination

A sequential injection analysis (SIA) using lab-on-valve with air segmentation and spectrophotometric detection was designed for copper(II) determination. It is based on the reaction of copper(II) and 2-carboxy-2′-hydroxy-5′-sulfoformazyl benzene (Zincon) in a weak alkaline solution between the air zones. Beer's Law was obeyed over the range of 0.1-2.0 mg L⁻¹ copper(II) with a correlation coefficient 0.9985 and a slope of 0.2893 absorbance unit/mg L⁻¹. The relative standard deviation was 2.0% for a series of 10 measurements of 0.5 mg L⁻¹ copper(II) solution. The detection limit (3 S/N) and the limit of quantification (LOQ) were 0.05 and 0.17 mg L⁻¹ respectively. This method has been successfully applied to determination of copper(II) in wastewater with a sample throughput of 120 h⁻¹. The method is superior to the batchwise method in that it provides fully automation, rapidity, less reagents and sample consumption with little waste generation.     

At-line determination of formaldehyde in bioprocesses by sequential injection analysis

A sequential injection analysis (SIA) method for the at-line determination of formaldehyde in a cultivation process of Pichia pastoris is presented. A genetically modified yeast strain was used for cultivation processes wherein methanol feed induced the production of the recombinant protein 1-3del I-TAC. Recurring measurements of culture medium, its blank and including standard addition were performed with Nash reagent using an automated syringe device and photometric detection. The apparatus was coupled via a laboratory-made flow-through adapter to a continuous filtered and cell-medium flow from the bioreactor. At-line monitoring of formaldehyde was performed at two cultivations, each of 250 h during fed-batch phases with glycerol and methanol as carbon sources. High reliability, robustness and reproducibility of the method, the software and the instrumentation as well as the high selectivity of the reaction were demonstrated.     

An automatic system for acidity determination based on sequential injection titration and the monosegmented flow approach

An automatic sequential injection system, combining monosegmented flow analysis, sequential injection analysis and sequential injection titration is proposed for acidity determination. The system enables controllable sample dilution and generation of standards of required concentration in a monosegmented sequential injection manner, sequential injection titration of the prepared solutions, data collecting, and handling. It has been tested on spectrophotometric determination of acetic, citric and phosphoric acids with sodium hydroxide used as a titrant and phenolphthalein or thymolphthalein (in the case of phosphoric acid determination) as indicators. Accuracy better than |4.4|% (RE) and repeatability better than 2.9% (RSD) have been obtained. It has been applied to the determination of total acidity in vinegars and various soft drinks. The system provides low sample (less than 0.3 mL) consumption. On average, analysis of a sample takes several minutes.     

Chemical speciation by sequential injection analysis: an overview

The simplicity of the sequential injection (SIA) manifold and its low need for maintenance makes it an ideal tool in speciation. As miniaturization and reduction of reagent consumption are also ultimate goals in chemical sensing, it is useful to review the use of combined injection and programmed flow as a central issue in designing SIA systems with chemical sensors and structurally simplified chemical analysers. This overview gives an insight into the current state, analytical scope and performance characteristics of sequential injection systems as analytical tools for speciation. The suitability of SIA for speciation analysis is illustrated by the methods used in the conduits of sequential injection systems for the chemical conversion of different chemical forms into detectable chemical species. Configurations of the basic sequential injection speciation analysis systems were designed around a multi-syringe-time-based-injection system with one detector, direct and indirect speciation of different forms using a single detector including diode array detection and direct speciation of different forms using multiple detection.

Examples showing the use of SIA for the simultaneous determination or speciation of metal ions, inorganic anions and organic compounds are given with some recent results from our research groups.     

Reversed flow injection and sandwich sequential injection methods for the spectrophotometric determination of copper(II) with cuprizone

Two new flow methods, flow injection analysis (FIA) and sequential injection analysis (SIA), for the spectrophotometric determination of Cu(II) in water at trace levels have been developed and optimised. Both methods are based on the reaction with oxalic acid bis(cyclohexylidene hydrazide) (cuprizone) in alkaline media. The two procedures have been developed for the final aim to compare their performances and to offer new rapid heavy metals analysis tools, avoiding the use of extraction steps. A detailed study of the physico-chemical parameters affecting the systems performances has been carried out. The reversed FIA and sandwich SIA approaches offered the best sensitivity. In both cases, an extremely good linearity has been obtained within the range 0.06-4 μg ml⁻¹ (correlation coefficient r=0.9999), whereas the observed detection limits were 0.013 and 0.004 μg ml⁻¹, for FIA and SIA, respectively. Furthermore, due to the great similarity of the diffusion zones in the reaction slugs, our approach offers the opportunity to compare the two methods in analogous conditions. This SIA method, besides keeping its typical reagent saving features, offered analytical performances equivalent to those of FIA. To obtain these results, an original “stop-flow like” method was successfully employed in the SIA approach. Both methods were validated by analysis of real water samples, after copper addition, and certified reference samples of fortified and waste waters.     

A sequential injection fluorometric procedure for rapid determination of total protein in human serum

A sensitive procedure for the quantification of total protein bovine serum albumen (BSA) in human serum was presented with sequential injection sampling and fluorometric detection. A few microliters of sample and fluorescamine solutions were aspirated into the holding coil to facilitate the reaction of protein with fluorescamine by giving rise to a blue-green-fluorescent derivative. The derivative was afterwards excited by a 400 nm radiation from a UV radiator, and the emitted fluorescence was monitored at the wavelength of 470 nm. By loading 5.0 μl of sample and 4.0 μl of fluorescamine solution 0.075% (m/v), a linear calibration graph was obtained within 0.3-12.5 μg ml⁻¹, and a detection limit (3σ) of 0.1 μg ml⁻¹ was achieved, along with a sampling frequency of 40 h⁻¹ and a R.S.D. value of 2.1% at the 5.0 μg ml⁻¹ levels. Protein contents in human serums were analyzed by using the present procedure, and reasonable agreements were obtained with those obtained by a documented spectrophotometric (Biuret) method.     

A review on sequential injection methods for water analysis

The development of fast, automatic and less expensive methods of analysis has always been the main aim of flow methodologies. The search for new procedures that still maintain the reliability and accuracy of the reference procedures is an ever growing challenge. New requirements are continually added to analytical methodologies, such as lower consumption of samples and reagents, miniaturisation and portability of the equipment, computer interfaces for full decision systems and so on. Therefore, the development of flow methodologies meeting the extra requirements of water analysis is a challenging work.Sequential injection analysis (SIA) presents a set of characteristics that make it highly suitable for water analysis. With sequential injection analysis, most routine determinations in waters can be performed more quickly with much lower reagent consumption when compared to reference procedures. Additionally, SIA can be a valuable tool for analyte speciation and multiparametric analysis. This paper critically reviews the overall work in this area.     

Simultaneous determination of pH, chloride and nickel in electroplating baths using sequential injection analysis

A sequential injection analysis system was developed to quantify pH, chloride and nickel in electrolytic baths, in the ranges 1-5 pH units, and 0.1-1.0 and 0.1-1.6 mol l⁻¹, respectively. To enable pH and chloride determination, potentiometric detection with two ion-selective electrodes in a tubular configuration was used. Nickel concentrations were assessed using colorimetric detection at 660 nm. pH was determined prior to nickel determination and just after sample injection (500 μl) into a 0.025 mol l⁻¹ phosphate buffer carrier stream at pH 6.3 and a 9.10 ml min⁻¹ flow rate. For chloride determination, on-line dialysis through a cellulose membrane was used to enable sample dilution and matrix separation. A 2⁵⁻¹ fractional factorial design based on the carrier solution composition and the levels of the hydrodynamic parameters was used for system optimization. At the optimized settings a sampling rate of 40 samples h⁻¹ was attained, with precision and accuracy statistically indistinguishable from those achieved with conventional procedures.     

Fluorescence optosensing implemented with sequential injection analysis: a novel strategy for the determination of labetalol

The coupling of sequential injection analysis and optosensing has been developed for the first time. It has been applied to the determination of labetalol in both pharmaceuticals and urine samples, with the analytical signal (native fluorescence) being monitored directly on sensing zone microbeads. The solid support used was the nonionic silica gel C₁₈, using 20% methanol–water (v:v) as a carrier. By using a 1.5-ml sample volume , we achieved a detection limit of 3.3 ng ml⁻¹. This sensitivity allowed the determination of the compound in urine samples. A recovery study was carried out at the labetalol levels usually found in urine after pharmaceuticals administration, and recovery percentages close to 100% were obtained. The relative standard deviation was 3.4% for 100 ng ml⁻¹ labetalol. No pretreatment was needed for urine samples, only an appropriate dilution, therefore minimizing the time required per sample analysis. In addition, the determination of the analyte was also carried out in one pharmaceutical, with a satisfactory result being obtained.     

High-sensitivity methods for sequential injection determination of the main constituents of alloys

A sequential injection system with spectrophotometric detection was proposed for the determination of copper, zinc and lead in brass. In view of the high analyte concentrations and the sensitivity of the involved catalytic methods, optimization of the flow system was carried out aiming mild reaction conditions. Copper and lead determinations were based on the catalytic effects of Cu²⁺ and Pb²⁺ on the oxidation rates of resorcinol and pyrogallol red by H₂O₂, respectively, and zinc determination involved precipitate formation after oxidation of 1-nafthylethylenediamine by K₃Fe(CN)₆. The analytical procedures were designed with some common parameters such as pH=9.0 (borate system), λ=530 nm, and H₂O₂ as oxidizing agent; system geometry was maintained.The proposed system is rugged, and base line drift is not observed during 4 h operation periods. Twenty samples are run per hour (60 determinations) and reagent consumption is minimal, thus avoiding drawbacks related to waste management. Precise results (R.S.D.<1.0%; n=7) are obtained and a detection limit of 1% (w/w) was estimated for the three analytes. Results were in agreement with flame atomic absorption spectrometry.     

Automated sequential injection fluorimetric determination and dissolution studies of Ergotamine Tartrate in pharmaceuticals

A fully automated flow system for drug-dissolution studies based on the sequential injection analysis (SIA) was described and used for monitoring dissolution profiles of Ergotamine Tartrate (ET) in pharmaceutical formulations. 50 μl of dissolution medium was taken for each measurement at a flow rate of 40 μl s⁻¹ and detected by fluorescence detector using λ_ex=236 nm (λ_em≥390 nm). The calibration curve was linear over the range 0.03–0.61 mg l⁻¹ of ET (sufficient for the dissolution tests). Equation of the calibration curve was calculated giving the following values: F=117.7 c+0.80 (n=6); r=0.9998. Detection limit was 0.01 mg l⁻¹ of ET. The R.S.D. is less than 0.54 and 0.86% (n=10) when determining 0.61 and 0.03 mg l⁻¹ of ET in standard solution, respectively. The dissolution test of Bellaspon tablets (0.3 mg of ET in 1 tablet) was programmed for 20 min, with a continuous sampling rate of 120 h⁻¹ under conditions required by BP 1993.     

Comparison of soluble manganese(IV) and acidic potassium permanganate chemiluminescence detection using flow injection and sequential injection analysis for the determination of ascorbic acid in Vitamin C tablets

The limits of detection (3s) for ascorbic acid were 5×10⁻⁸ M with acidic potassium permanganate using both flow injection analysis (FIA) and sequential injection analysis (SIA) whereas the soluble manganese(IV) afforded 1×10⁻⁸ M and 5×10⁻⁹ M for FIA and SIA, respectively. Determinations of ascorbic acid in Vitamin C tablets were achieved with minimal sample pretreatment using a standard additions calibration and gave good agreement with those of iodimetric titration.     

SIAmate-a compact and modular sequential injection analysis controller

A number of sequential injection analysis (SIA) measurement methods have been developed during the last years. Almost all have been used in laboratory conditions with good results, but very few have been implemented as on-line methods, applied to non-stop measurements, producing immediate results for process control. The transfer of an SIA system from laboratory to an industrial facility [J. Ruzicka, Anal. Chim. Acta 261 (1992) 3] requires a whole new range of details to be taken into account. Some SIA platform related topics will be discussed. There are numerous ways of building an SIA system that meets the needs of the industry. One alternative, SIAmate, is presented.     

Development of a capillary electrophoresis system coupled to sequential injection analysis and evaluation by the analysis of nitrophenols

A combination of a laboratory-made capillary electrophoresis system and a sequential injection analysis equipment is described. For characterization, the system was successfully applied to the separation and quantification of nitrophenols. A blue LED was used as light source, and hydrodynamic injection was carried out by using a pressure-stable solenoid valve and an inflatable pressure reservoir. A good reproducibility of migration time (0.5%) and peak heights (5%) were obtained. The calibration by using peak heights was found to be linear up to 776?µmol?L^?1 for all three compounds. The system was robust and reliable for autonomous analysis without observation. All maintenance requirements including the conditioning of the capillary and flushing of both buffer reservoirs were carried out automatically. Instrumentation aspects of the capillary electrophoresis part are compared with former described hyphenated flow systems showing maximal operation versatility. Instrumental control and data evaluation were carried out using the software package AutoAnalysis.     

Microfabricated electroosmotic pump for capillary-based sequential injection analysis

A microfabricated electroosmotic pump with an integrated serpentine isolation channel was developed on a glass chip and applied to a capillary-based sequential injection analysis (SIA) system for an enzyme inhibition assay. The pump chip contains an anode reservoir, an ion-exchange membrane electric field decoupler (EFD) that also serves as a cathode reservoir, parallel pump channels and an isolation channel. A two-step etching process was adopted to etch the pump channels to a depth of 20 μm and the isolation channel to a depth of 90 μm. The pump flow rate was very stable: the relative standard deviation (RSD) of the pump rate was 1.9% for propulsion and 2.3% for aspiration. The pump chip was successfully applied to a capillary-based sequential injection analysis system with a confocal fluorescence detector. For repetitive analysis of a 13 μM fluorescein solution, an RSD of 0.6% was attained, which demonstrated the flow stability of the EOF pump. The system was then applied to an enzyme inhibition assay, the diethylenetriaminepentaacetic acid (DTPA) inhibition of the β-galactosidase-catalyzed hydrolysis of fluorescein di(β-d-galactopyranoside). Reproducible results (RSD<3.0%) were obtained.