Hybrid mesoporous materials for on-line preconcentration of Cr(VI) followed by one-step scheme for elution and colorimetric determination at ultratrace levels

An hybrid mesoporous material synthesised in our laboratories for solid phase extraction (SPE) in flow through systems has been used for analytical purposes. The solid was obtained from mesoporous silica MCM-41 functionalized with 3-aminopropyltriethoxy silane by Sol-Gel methodology. In order to exploit the large sorption capacity of the material together with the possibility of modeling it for anions retention, a microcolumn (MC) filled with the solid was inserted in a flow system for preconcentration of Cr(VI) and its determination at ultratrace levels in natural waters. The analytical methodology involved a reverse flow injection system (rFI) holding a MC filled with the solid for the analyte extraction. Elution and colorimetric detection were carried out with 1-5 diphenylcarbazide (DPC) in sulfuric acid. DPC produced the reduction of Cr(VI) to Cr(III) together with the generation of a cationic red complex between Cr(III) and 1-5 diphenylcarbazone which was easily eluted and detected with a visible spectrophotometer. Moreover, the filling material got ready for the next sample loading remaining unspoiled for more than 300 cycles.The effect of several variables on the analytical signal as well as the influence of cationic and anionic interferences were discussed. Particular attention was given to sulfuric acid interference since it is the required media for the complex generation.Under optimal conditions, 99.8% of Cr(VI) recovery was obtained for a preconcentration time of 120 s (sample and DPC flow rates = 1 mL min⁻¹) and an elution volume of 250 μL. The limit of detection (3 s) was found to be 0.09 μg L⁻¹ Cr(VI) with a relative standard deviation (n = 10, 3 μg L⁻¹) of 1.8.Since no Cr(III) was retained by the solid material and Cr(VI) was completely adsorbed, electrothermal atomic absorption spectrometry (ET AAS) determinations of Cr(III) were also performed by simply measuring its concentration at the end of the microcolumn after Cr(VI) retention by the mesoporous solid.Applications to the determination of Cr(VI) and Cr(III) in natural waters and the validation of the methodology were also studied.     

Simultaneous extraction and preconcentration of uranium and thorium in aqueous samples by new modified mesoporous silica prior to inductively coupled plasma optical emission spectrometry determination

A new synthesized modified mesoporous silica (MCM-41) using 5-nitro-2-furaldehyde (fural) was applied as an effective sorbent for the solid phase extraction of uranium(VI) and thorium(IV) ions from aqueous solution for the measurement by inductively coupled plasma optical emission spectrometry (ICP OES). The influences of some analytical parameters on the quantitative recoveries of the analyte ions were investigated in batch method. Under optimal conditions, the analyte ions were sorbed by the sorbent at pH 5.5 and then eluted with 1.0 mL of 1.0 mol L⁻¹ HNO₃. The preconcentration factor was 100 for a 100 mL sample volume. The limits of detection (LOD) obtained for uranium(VI) and thorium(IV) were 0.3 μg L⁻¹. The maximum sorption capacity of the modified MCM-41 was found to be 47 and 49 mg g⁻¹ for uranium(VI) and thorium(IV), respectively. The sorbent exhibited good stability, reusability, high adsorption capacity and fast rate of equilibrium for sorption/desorption of uranium and thorium ions. The applicability of the synthesized sorbent was examined using CRM and real water samples.     

Speciation of vanadium in water with quinine modified resin micro-column separation/preconcentration and their determination by fluorination assisted electrothermal vaporization (FETV)-inductively coupled plasma optical emission spectrometry (ICP-OES)

A simple and selective method of flow injection (FI) using a micro-column packed with quinine modified resin as solid phase extractant has been developed for preconcentration and separation of trace amount of vanadium(V) and vanadium(IV) in water samples, followed by determination with fluorination assisted electrothermal vaporization (FETV)-inductively coupled plasma optical emission spectrometry (ICP-OES). At pH 3 ∼ 3.8, the modified resin is selective towards V(V) and almost not towards V(IV), while, V(IV) could be quantitatively adsorbed by the modified resin at pH 5 ∼ 7. The two vanadium species adsorbed by modified resin could be readily desorbed quantitatively with 0.3 ml of 0.5 mol l⁻¹ HCl. Both vanadium species in elution were then determined by ETV-ICP-OES with the use of polytetrafluoroethylene (PTFE) as chemical modifier. Effects of acidity, sample flow rate, concentration of elution solution and interfering ions on the recovery of the analytes have been systematically investigated. Under the optimal conditions, the adsorption capacities of the quinine modified resin for V(V) and V(IV) are 7.6 and 8.0 mg g⁻¹, respectively. The detection limit (3σ) of V is 0.072 ng ml⁻¹ for FETV-ICP-OES and 0.56 pg ml⁻¹ for FETV-ICP-MS with enrichment factor of 62.5, and the relative standard deviation (R.S.D.) is 4.9% (n = 9, C = 0.2 μg ml⁻¹) and 3.8% (n = 9, C = 1.0 ng ml⁻¹), respectively. The proposed method has been applied to the determination of trace V(V) and V(IV) in different water samples, and the recoveries of V(V) and V(IV) are 100 ± 10%. In order to further verify the accuracy of the developed method, FETV-ICP-MS was employed to analyze the vanadium species in water samples after separation/preconcentration, and analytical results are in good agreement with that obtained by the proposed method. The developed method was also applied to the analysis of the total V in GBW07401 soil certified reference material and in GBW07605 tea leaves certified reference material, and the determined values coincided with the certified values very well.     

Sorption of As(V) from waters using chitosan and chitosan-immobilized sodium silicate prior to atomic spectrometric determination

A natural biosorbent containing amine functional groups, chitosan, and a novel sorbent, chitosan-immobilized sodium silicate, were prepared and utilized for the selective sorption of As(V) from waters prior to its determination by atomic spectrometric techniques, namely, hydride generation atomic absorption spectrometry (HGAAS) and inductively coupled plasma mass spectrometry (ICP-MS). Chitosan was synthesized from chitin and sodium silicate was used as the immobilization matrix due to its straightforward synthesis. Through sequential sorption studies, it was shown that chitosan-immobilized sodium silicate has exhibited a better chemical stability than the chitosan itself which demonstrates the advantage of immobilization method. Both chitosan and chitosan-immobilized sodium silicate were shown to selectively adsorb As(V), arsenate, from waters at pH 3.0 at which neither chitin nor sodium silicate displayed any sorption towards As(V). The sorption of arsenate by chitosan is supposed to have electrostatic nature since pH of 3.0 is both the point at which the amino groups in chitosan are protonated and also the predominant form of As(V) is H₂AsO₄⁻. A pre-oxidation step is required if both As(III) and As(V) are to be determined. Desorption from the sorbents was realized with 1.0% (w/v) l-cysteine prepared in a pH 3.0 solution adjusted with HCl. Among the possible interfering species tested, only Te(IV) and Sb(III) were shown to cause a decrease in the sorption capacity especially at high interferant concentrations. High concentrations of Sb(III) also resulted in gas phase interference during hydride generation.The validity of the method was checked both via spike recovery experiments and also through the analysis of a standard reference material. Spike recovery tests were carried out with four different types of water; namely, ultra-pure, bottled drinking, tap, and sea water; and percent recovery values were found to be 114 (±4), 112 (±2), 43 (±4), and 0 (±1), respectively. It was concluded that the proposed methodology can be applied efficiently to low-to-medium ionic strength solutions, such as most drinking waters. The accuracy of the method was additionally investigated through the analysis of a standard reference material and a good correlation was found between the determined (26.6 ± 2.4 μg L⁻¹) and the certified (26.67 μg L⁻¹) value.     

Mesoporous silica-based electrochemical sensor for sensitive determination of environmental hormone bisphenol A

Bisphenol A (BPA) is an emerging contaminant with severe toxic effects such as disrupting endocrine system or causing cancer, therefore, developing sensitive and selective sensor for BPA is very important and interesting. Herein, MCM-41, a kind of mesoporous silica, was synthesized and then used to prepare an electrochemical sensor for BPA. For better comparison, carbon nanotubes, activated carbon, silica gel and graphite were also employed to prepare electrochemical sensor for BPA. The electrochemical behaviors of BPA at different electrochemical sensors were investigated. Compared with other sensors, the MCM-41 sensor greatly enhances the response signal of BPA due to the large active surface area and high accumulation efficiency. The effects of pH value, accumulation time and sensor composition were examined. The linear range is from 2.2 × 10⁻⁷ to 8.8 × 10⁻⁶ mol L⁻¹, and the limit of detection is evaluated to be 3.8 × 10⁻⁸ mol L⁻¹. Finally, the MCM-41 sensor was successfully employed to determine BPA in water samples.     

Speciation of arsenic(III) and arsenic(V) by inductively coupled plasma-atomic emission spectrometry coupled with preconcentration system

A novel and simple flow-based method was developed for the simultaneous determination of As(III) and As(V) in freshwater samples. Two miniature columns with a solid phase anion exchange resin, placed on two 6-way valves were utilized for the solid-phase collection/concentration of arsenic(III) and arsenic(V), respectively. As(III) could be retained on the column after its oxidation to As(V) species with an oxidizing agent. The collected analytes were then sequentially eluted by 2 M nitric acid and introduced into ICP-AES. Potassium permanganate was examined as potential oxidizing agent for conversion of As(III) to As(V). The standard deviation of the analytical signals (peak height) for the replicate analysis (n = 5) of 0.5 μg l⁻¹ solution were 3 and 5% for As(III) and As(V), respectively. The limit of detection (3σ) for both As(III) and As(V) were 0.1 μg l⁻¹. The proposed system produced satisfactory results on the application to the direct analysis of inorganic arsenic species in freshwater samples.     

Amino-functionalized mesoporous silica modified glassy carbon electrode for ultra-trace copper(II) determination

This paper described a facile and direct electrochemical method for the determination of ultra-trace Cu²⁺ by employing amino-functionalized mesoporous silica (NH₂-MCM-41) as enhanced sensing platform. NH₂-MCM-41 was prepared by using a post-grafting process and characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM) and fourier transform infrared (FTIR) spectroscopy. NH₂-MCM-41 modified glassy carbon (GC) electrode showed higher sensitivity for anodic stripping voltammetric (ASV) detection of Cu²⁺ than that of MCM-41 modified one. The high sensitivity was attributed to synergistic effect between MCM-41 and amino-group, in which the high surface area and special mesoporous morphology of MCM-41 can cause strong physical absorption, and amino-groups are able to chelate copper ions. Some important parameters influencing the sensor response were optimized. Under optimum experimental conditions the sensor linearly responded to Cu²⁺ concentration in the range from 5 to 1000 ng L⁻¹ with a detection limit of 0.9 ng L⁻¹ (S/N = 3). Moreover, the sensor possessed good stability and electrode renewability. In the end, the proposed sensor was applied for determining Cu²⁺ in real samples and the accuracy of the results were comparable to those obtained by inductively coupled plasma optical emission spectrometry (ICP-OES) method.     

Trinuclear Schiff base complexes with uranium(V) and copper(II) or zinc(II) ions

Treatment of the uranium(IV) complexes [{ML¹(py)}₂U^IV] (M = Cu, Zn; L¹ = N,N′-bis(3-hydroxysalicylidene)-1,3-propanediamine) with silver nitrate in pyridine led to the formation of the corresponding cationic uranium(V) species which were found to be thermally unstable and were converted back into the parent U^IV complexes; no electron transfer was observed in solution between the U^IV and U^V compounds. In the crystals of [{ML¹(py)}₂U^IV][{ML¹(py)}₂U^V][NO₃], the neutral U^IV and cationic U^V species are clearly identified by the distinct U–O distances. Similar reaction of [{ZnL²(py)}₂U^IV] [L² = N,N′-bis(3-hydroxysalicylidene)-1,4-butanediamine] with AgNO₃ gave crystals of [{ZnL²(py)}U^V{ZnL²(py)₂}][NO₃] but the copper counterpart was not isolated. Crystals of [{ZnL¹(py)}₂U^V][OTf] · THF (OTf = OSO₂CF₃) were obtained fortuitously from the reaction of [Zn(H₂L¹)] and U(OTf)₃.     

Modified mesoporous silica materials for on-line separation and preconcentration of hexavalent chromium using a microcolumn coupled with flame atomic absorption spectrometry

A modified SBA-15 mesoporous silica material NH₂-SBA-15 was synthesized successfully by grafting γ-aminopropyl-triethoxysilane. The material was characterized using transmission electron microscopy (TEM) and Fourier transform infrared/Raman (FT-IR/Raman) spectroscopy, and used for the first time in a flow injection on-line solid phase extraction (SPE) coupled with flame atomic absorption spectrometry (FAAS) to detect trace Cr (VI). Effective sorption of Cr (VI) was achieved at pH 2.0 with no interference from Cr (III) and other ions and 0.5 mol L⁻¹ NH₃·H₂O solution was found optimal for the complete elution of Cr (VI). An enrichment factor of 44 and was achieved under optimized experimental conditions at a sample loading of 2.0 mL min⁻¹ sample loading (300 s) and an elution flow rate of 2.0 mL min⁻¹ (24 s). The precision of the 11 replicate Cr (VI) measurements was 2.1% at the 100 μg L⁻¹ level with a detection limit of 0.2 μg L⁻¹ (3 s, n = 10) using the FAAS. The developed method was successfully applied to trace chromium determination in waste water. The accuracy was validated using a certified reference material of riverine water (GBW08607).     

Preparation of a new Cd(II)-imprinted polymer and its application to determination of cadmium(II) via flow-injection-flame atomic absorption spectrometry

A new cadmium(II)-imprinted polymer based on cadmium(II) 2,2′-{ethane-1,2-diylbis[nitrilo(E)methylylidene]} diphenolate-4-vinylpyridine complex was obtained via suspension polymerization. The beads were used as a minicolumn packing for flow-injection-flame atomic absorption spectrometry (FI-FAAS) determination of cadmium(II) in water samples. Sorption effectiveness was optimal within pH range of 6.6-7.7. Nitric acid, 0.5% (v/v) was used as eluent. Fast cadmium(II) sorption by the proposed material enabled to apply sample flow rates up to 10 mL min⁻¹ without loss in sorption effectiveness. Enrichment factor (EF), concentration efficiency (CE) and limit of detection (LOD, 3σ) found for 120-s sorption time were 117, 39.1 min⁻¹ and 0.11 μg L⁻¹, respectively. Sorbent stability was proved for at least 100 preconcentration cycles (RSD = 2.9%). When compared to non-imprinted polymer the new Cd(II)-imprinted polymer exhibited improved selectivity towards cadmium(II) against other heavy metal ions, especially Cu(II) and Pb(II), as well as light metal ions. Accuracy of the method was tested for ground water and waste water certified reference materials and fortified water. The method was applied to Cd(II) determination in natural water samples.     

A simple and fast method for chlorsulfuron and metsulfuron methyl determination in water samples using multiwalled carbon nanotubes (MWCNTs) and capillary electrophoresis

A new method to determine metsulfuron methyl (MSM) and chlorsulfuron (CS) in different water samples was developed. It consists in a solid phase extraction (SPE) procedure using multiwalled carbon nanotubes (MWCNTs) as sorbent material in combination with capillary zone electrophoretic determination. To carry out the pre-concentration step, a simple flow injection system was developed and optimized. Thus, 250 μL of aqueous solution containing methanol 50% (v/v) and acetonitrile 2% (v/v) as eluent, 10 mL of sample and a flow rate of 1.15 mL min⁻¹ were selected. The CE variables also were optimized. A rapid determination and good resolution of two herbicides were obtained within 9 min using a simple electrophoretic buffer (50 mmol L⁻¹ sodium tetraborate with 3% of methanol, pH = 9.0). Under the optimum conditions, the calibration curves were linear between 0.5 and 6 μg L⁻¹ for MSM and CS with R² = 0.995 and 0.997, respectively. The repeatability of the proposed method, expressed as relative standard deviation (RSD), varied between 4.1% and 5.4% (n = 10) and the detection limits for MSM and CS were 0.40 and 0.36 μg L⁻¹, respectively. Good results were achieved when the proposed method was applied to spiked real water samples. The recoveries percentages of the two analytes were over the range 86-108%.     

Silica modified with zirconium oxide for on-line determination of inorganic arsenic using a hydride generation-atomic absorption system

In the present work, an on-line pre-concentration system, using SiO₂/ZrO₂ as solid phase adsorbent, for the determination of low concentrations of arsenic was developed.In this procedure, total inorganic arsenic present in the sample is reduced to As (III) with l-cysteine and the solution is passed into a glass column (?_i = 3 mm; h = 35 mm) containing 70 mg of SiO₂/ZrO₂ (100-230 mesh) to retain the As (III), with the solution flowing at 3.2 mL min⁻¹. After 2 min, the concentrated species are eluted with 3 mol L⁻¹ HCl (3.2 mL min⁻¹) loading a 150 μL loop while a 1.0% (m/v) sodium borohydride solution loads the other loop of a FI-HG AAS system. The elution step is carried out during 7 s and, at the same time, the SiO₂/ZrO₂ phase is regenerated for the next concentration cycle. The arsine generated is carried with N₂ (flow rate = 90 mL min⁻¹) to a quartz cell where the electrothermal atomization process occurs.Under these conditions, a 20-fold enrichment factor is obtained considering the increase of sensitivity in the analytical curve after the concentration step. The limits of detection and quantification were 0.05 and 0.35 μg L⁻¹, respectively, with an injection frequency of about 28 h⁻¹ and relative standard deviation lower than 8%. Four metallurgical reference materials were analyzed with the proposed method after their acid dissolution. The results obtained were in good agreement with certified values.     

Application of the spectral correction method and "neural networks" for simultaneous determination of V(V) and Al(III)

Simultaneous determination of V(V) and Al(III) was performed by application of neural networks when the calibration matrix was performed using β-correction spectra. Two reactions between V(V) and Al(III) and Alizarin Red S (ARS) as a ligand have been investigated and applied for the simultaneous spectrophotometric determination of these metal ions. The parameters controlling behavior of the system were investigated and optimum conditions selected. Feed-forward neural networks have been trained to quantify considered metal ions in mixtures under optimum conditions. Sigmoidal functions were used in the hidden and output layers. Determinations were made over the concentration range 0.10-7.80 μg ml⁻¹ of V(V) and 0.11-4.20 μg ml⁻¹ of Al(III). Applying this method satisfactorily to simultaneous determination of these metal ions in several synthetic solutions with total relative standard error less than 4.02% validated the proposed method.     

Synthesis of salicylaldehyde-modified mesoporous silica and its application as a new sorbent for separation, preconcentration and determination of uranium by inductively coupled plasma atomic emission spectrometry

A new functionalized mesoporous silica (MCM-41) using salicylaldehyde was utilized for the separation, preconcentration and determination of uranium in natural water by inductively coupled plasma atomic emission spectrometry (ICP-AES).Experimental conditions for effective adsorption of trace levels of U(VI) were optimized. The preconcentration factor was 100 (1.0 mL of elution for a 100 mL sample volume). The analytical curve was linear in the range 2-1000 μg L⁻¹ and the detection limit was 0.5 ng mL⁻¹. The relative standard deviation (R.S.D.) under optimum conditions was 2.5% (n = 10). Common coexisting ions did not interfere with the separation and determination of uranium at pH 5. The sorbent exhibited excellent stability and its sorption capacity under optimum conditions has been found to be 10 mg of uranium per gram of sorbent. The method was applied for the recovery and determination of uranium in different water samples.     

Oxovanadium(V) complexes incorporating tridentate aroylhydrazoneoximes: Synthesis, characterizations and antibacterial activity

Some new oxovanadium(V) complexes, [VOL^1-3(OEt)(EtOH)] (1-3), have been reported, which were obtained from the reaction of the Schiff bases H₂L^1-3 (where H₂L¹ = the salicylhydrazone of diacetyl monoxime; H₂L² = the 4-methoxy salicylhydrazone of diacetyl monoxime and H₂L³ = the 4-hydroxy salicylhydrazone of diacetyl monoxime) with VO(acac)₂ in a 1:1 molar ratio. Three 4-R-aroylhydrazoneoximes (V) have been used as ligands in the present study, differing in the inductive effect of the substituent R (R = H, OCH₃ and OH), in order to observe their influence, if any, on the redox potentials and biological activity of the complexes. All the synthesized ligands and metal complexes were successfully characterized by elemental analysis, IR, UV-Vis and NMR spectroscopy. An X-ray diffraction study of [VOL¹(OEt)(EtOH)] (1) reveals that the metal center has a distorted octahedral O₅N coordination sphere, where the O,N,O donor ligand and the ethoxo group constitute a satisfactory O₃N basal plane. Cyclic voltammetry of the complexes show a quasi-reversible cyclic voltammetric response in the potential range 0.29-0.36 V involving a single electron V(V)-V(IV) reduction. The complexes have also been screened for their antibacterial activity against Escherichia coli, Bacillus, Proteus and Klebsiella. Minimum inhibitory concentrations of these complexes and the antibacterial activities indicate compound 1 as the potential lead molecule for drug design.     

Analysis of interferents by means a D-optimal screening design and calibration using partial least squares regression in the spectrophotometric determination of Cr(VI)

Using a central composite design, the signal of the process for the spectrophotometric determination of hexavalent chromium (λ = 543 nm) is maximised and its variability minimised using as complexing agent 1,5-diphenylcarbazide in sufficiently acid medium. To analyse the interference of various analytes (Mo(VI), V(V), Fe(III) and Mn(VII)) on the Cr(VI) as a function of concentration of interferent, a factorial design was prepared at three levels of each (zero, medium and high concentration), which implies performing 81 determinations. However, a D-optimal design with just nine experiments is sufficiently good to estimate the model proposed.The interference of these metals makes it impossible to determine Cr(VI) when they are present in the sample. To avoid prior separation steps, a multivariate regression by partial least squares, PLS, is proposed to calibrate the Cr(VI) in the presence of these analytes varying the concentration of the Cr(VI) between 0.1 and 0.9 μg ml⁻¹ and that of the interferents between 3 and 5 μg ml⁻¹. The average errors obtained were 4.5% and 3.29% fitted and in prediction, respectively, with a standard error in prediction (RMSEP) of 0.016% presenting absence of both constant and proportional bias.The detection limit with the PLS regression in the presence of interferents is 0.1 μg ml⁻¹ with a probability of false positive equal to 5% and less than 5% for false negative. The capability of detection is similar to that obtained with the univariate calibration (absorbance at 543 nm) in absence of interferents.With the PLS regression it is possible to discriminate 0.085 μg ml⁻¹ of Cr(VI) in a sample with 0.5 μg ml⁻¹ of Cr(VI) with probabilities of false compliance and false non-compliance equal to 0.05. For the univariate calibration without interferents, it was established at 0.0971 μg ml⁻¹ of Cr(VI) for the same nominal concentration.In relation to interference of V(V), Fe(III) and Mn(VII), the PLS calibration could be an efficient alternative to the separation step for Cr(VI) spectrophotometric determination using 1,5-diphenylcarbazide.     

Sorption characteristics and chromatographic separation of gold (I and III) from silver and base metal ions using polyurethane foams

The influence of different parameters on the sorption profiles of trace and ultra traces of gold (I) species from the aqueous cyanide media onto the solid sorbents ion exchange polyurethane foams (IEPUFs) and commercial unloaded polyurethane foams (PUFs) based polyether type has been investigated. The retention of gold (I) species onto the investigated solid sorbents followed a first-order rate equation with an overall rate constant k in the range 2.2-2.8 ± 0.2 s⁻¹. The sorption data of gold (I) followed Freundlich and Langmuir isotherm models. Thus, the a dual-mode of sorption mechanism involving absorption related to “weak base anion exchanger” and an added component for “surface adsorption” seems the most likely proposed dual mechanism for retention profile of gold (I) by the IEPUFs and PUFs solid sorbents. The capacity of the IEPUFs and PUFs towards gold (I) sorption calculated from the sorption isotherms was found to be 11.21 ± 1.8 and 5.29 ± 0.9 mg g⁻¹, respectively. The chromatographic separation of the spiked inorganic gold (I) from de ionized water at concentrations 5-15 μg mL⁻¹ onto the developed IEPUFs and PUFs packed columns at 10 mL min⁻¹ flow rate was successfully achieved. The retained gold (I) species were then recovered quantitatively from the IEPUFs (98.4 ± 2.4%, n = 5) and PUFs (95.4 ± 3.4%, n = 5) packed columns using perchloric acid (60 mL, 1.0 mol L⁻¹) as a proper eluating agent. Thiourea (1.0 mol L⁻¹)-H₂SO₄ (0.1 mol L⁻¹) system was also used as eluating agent for the recovery of gold (I) from IEPUFS (95.4 ± 5.4%, n = 3) and also PUFs (93.4 ± 4.4%, n = 3) packed columns. The performance of the IEPUFs and PUFs packed columns in terms of the height equivalent to the theoretical plates (HETP), number of plates (N), and critical and breakthrough capacities towards gold (I) species were evaluated. The developed IEPUFs packed column was applied successfully for complete retention and recovery (98.5 ± 2.7) of gold (III) species spiked onto tap- and industrial wastewater samples at <10 μg Au mL⁻¹ after reduction to gold (I). The IEPUFs packed column was applied satisfactorily for complete retention and recovery (98.5 ± 2.7) of total inorganic gold (I) and/or gold (III) species spiked to tap- and industrial wastewater samples at <10 μg mL⁻¹ gold. Chromatographic separation of gold (I) from silver (I) and base metal ions (Fe, Ni, Cu and Zn) using IEPUFS packed columns was satisfactorily achieved. The proposed method was applied successfully for the pre-concentration and separation from anodic slime and subsequent FAAS determination of analyte with satisfactory results (recoveries >95%, relative standard deviations <4.0%).     

Development and validation of a hydrophilic interaction liquid chromatographic method for determination of aromatic amines in environmental water

A simple, precise, and accurate hydrophilic interaction liquid chromatographic (HILIC) method has been developed for the determination of five aromatic amines in environmental water samples. Chromatography was carried out on a bare silica column, using a mixture of acetonitrile and a buffer of NaH₂PO₄–H₃PO₄ (pH 1.5, containing 10 mM NaH₂PO₄) (85:15, v/v) as a mobile phase at a flow rate of 1 mL min⁻¹. Aromatic amines were detected by UV absorbance at 254 nm. The linear range of amines was good (r² > 0.998) and limit of detection (LOD) within 0.02–0.2 mg L⁻¹ (S/N = 3). The retention mechanism for the analytes under the optimum conditions was determined to be a combination of adsorption, partition and ionic interactions. The proposed method was applied to the environmental water samples. Aromatic amines were isolated from aqueous samples using solid-phase extraction (SPE) with Oasis HLB cartridges. Recoveries of greater than 75% with precision (RSD) less than 12% were obtained at amine concentrations of 5–50 μg L⁻¹ from 100 mL river water and influents from a wastewater treatment plant (WWTP). The present HILIC technique proved to be a viable method for the analysis of aromatic amines in the environmental water samples.     

A novel flow injection chemiluminescence determination of Cr(VI) with Dichlorotris(1,10-phenanthroline)ruthenium(II)

A selective novel reverse flow injection system with chemiluminescence detection (rFI-CL) for the determination of Cr(VI) in presence of Cr(III) with Dichlorotris (1,10-phenanthroline)ruthenium(II), (Ru(phen)₃Cl₂), is described in this work. This new method is based on the oxidation capacity of Cr(VI) in H₂SO₄ media. First, the Ruthenium(II) complex is oxidized to Ruthenium(III) complex by Cr(VI) and afterwards it is reduced to the excited state of the Ruthenium(II) complex by a sodium oxalate solution, emitting light inside the detector. The intensity of chemiluminescence (CL) is proportional to the concentration of Cr(VI) and, under optimum conditions, it can be determined over the range of 3-300 μg L⁻¹ with a detection limit of 0.9 μg L⁻¹. The RSD was 8.4% and 1.5% at 5 and 50 μg L⁻¹, respectively. For the rFI-CL method various analytical parameters were optimized: flow rate (1 mL min⁻¹), H₂SO₄ carrier concentration (20% w/V), Ru(phen)₃Cl₂ concentration (5 mM) and sodium oxalate concentration (0.1 M). The effect of Cr(III), Fe(III), Al(III), Cd(II), Zn(II), Hg(II), Pb(II), Ca(II) and Mg(II), was studied. The method is highly sensitive and selective, allowing a fast, on-line determination of Cr(VI) in the presence of Cr(III). Finally, the method was tested in four different water samples (tap, reservoir, well and mineral), with good recovery percentage.