Comparison of ultrasonic and pressurized liquid extraction for the analysis of polycyclic aromatic compounds in soil samples by gas chromatography coupled to tandem mass spectrometry

A pressurized liquid extraction (PLE) method has been optimized for the determination of polycyclic aromatic hydrocarbons (PAHs) in soil samples and it was compared with ultrasonic extraction. The extraction step was followed by gas chromatography-triple quadrupole mass spectrometry (GC-QqQ-MS/MS) analysis. Parameters such as type of solvent, extraction time, extraction temperature and number of extractions were optimized. There were no significant differences among the two extraction methods although better extraction efficiencies were obtained when PLE was used, minimizing extraction time and solvent consumption. PLE procedure was validated, obtaining limits of detection (LODs) ranging from 0.02 to 0.75 μg kg⁻¹ and limits of quantification (LOQs) ranging from 0.07 to 2.50 μg kg⁻¹ for the selected PAHs. Recoveries were in the range of 59-110%, except for naphthalene, which was the most volatile PAH. Finally, the method was applied to real soil samples from Southeast of Spain. PAHs concentrations were low, and phenanthrene, pyrene, fluorene, benzo[a]pyrene and chrysene were the most frequently detected analytes in the samples.     

Evaluation of surfactant assisted pressurized liquid extraction for the determination of glycyrrhizin and ephedrine in medicinal plants

Surfactant assisted pressurized liquid extraction (PLE) with a laboratory made system was applied for the extraction of glycyrrhizin in Radix glycyrrhizae/liquorice and ephedrine in Ephedra sinica. The proposed system set-up for this current work was simpler as no heating and back pressure regulator was required. Extraction with surfactant assisted PLE was carried out dynamically at a flow of 1.5 mL min⁻¹, at room temperature, under an applied pressure of 10-20 bar with an extraction time of 45-50 min. The extraction efficiencies of the proposed method using surfactants such as sodium dodecyl sulfate (SDS) and Triton X-100 were compared with sonication using organic solvent for different batches of medicinal plants materials. For the determination of glycyrrhizin in R. glycyrrhizae, the extraction efficiencies of surfactant assisted PLE with SDS and Triton X-100 was observed to be comparable with sonication. The method precision was found to vary from 1.6 to 2.6% (R.S.D., n = 6) on different days. For ephedrine in E. sinica, surfactant assisted PLE with SDS was found to give higher extraction efficiencies compared to Triton X-100. The overall method precision for surfactant assisted PLE with SDS for ephedrine in E. sinica was found to vary from 1.5 to 4.1% (R.S.D., n = 6) on different days. The marker compounds present in the various medicinal plant extracts were determined by gradient elution HPLC. Our data showed the possibility of PLE at room temperature and the advantages of eliminating the use of organic solvents in the extraction process.     

Suitability of selective pressurized liquid extraction combined with gas chromatography-ion-trap tandem mass spectrometry for the analysis of polybrominated diphenyl ethers

A one-step extraction and clean-up method using pressurized liquid extraction (PLE) (selective PLE) combined with gas chromatography-ion-trap tandem mass spectrometry (GC-ITMS-MS) was evaluated for the analysis of polybrominated diphenyl ethers (from tri- to hepta-PBDEs) at low concentrations in fish and shellfish samples. To this end, the performance of an on-line PLE extraction/clean-up method and of a classical Soxhlet extraction and clean-up method using a multi-layer modified silica column were compared. The two sample treatment methods provided similar results, although an important reduction in the sample treatment time (40 min per sample) was achieved using the selective PLE method. In addition, the suitability of the PLE combined with GC-ITMS-MS method was evaluated by comparing the results obtained in the analysis of fish samples with those obtained by gas chromatography-high resolution mass spectrometry (GC-HRMS). Good agreement between both techniques was obtained with differences between the mean values of less than 16%. The selective PLE method coupled to GC-ITMS-MS produced accurate results for PBDE determination with low limits of detection (1.0-16.8 pg g⁻¹ wet weight) and quantification (3.1-51 pg g⁻¹ wet weight) as well as good precision (RSD < 16%). This method has been applied to the analysis of PBDEs in fish and shellfish samples collected at fish markets in Catalonia (NE Spain).     

Simultaneous determination of fluoroquinolones,sulfonamides and tetracyclines in sewage sludge by pressurized liquid extraction and liquid chromatography electrospray ionization-mass spectrometry

A new scheme for the quantitative determination of traces of fluoroquinolones (FQs), tetracyclines (TCs) and sulfonamides (SAs) in sewage sludge was developed. The compounds were simultaneously extracted from sewage sludge by pressurized liquid extraction (PLE). A novel and effective method for PLE was developed. Solid-phase extraction was used for cleaning up the extracts. Identification and quantification of the compounds was done using high-performance liquid chromatography with electrospray ionization mass spectrometry in selected reaction monitoring mode. The best recovery of FQs and TCs was obtained by using hydrophilic–lipophilic balance cartridges, recoveries ranged 59% for norfloxacin to 82% for ofloxacin and 95% for doxycycline; for SAs strong cation-exchange cartridges were more efficient, recoveries were 96% for sulfamethoxazole and 43% for sulfadimethoxine. Limit of quantification ranged from 0.1 ng/g for SAs to 160 ng/g for tetracycline. Method precision for TCs was 5.06% and 1.12%, and for SAs 0.43% and 2.01%. FQs precision ranged from 0.77% to 1.89%.     

Negative-pressure cavitation extraction for the determination of flavonoids in pigeon pea leaves by liquid chromatography-tandem mass spectrometry

A new method, namely negative-pressure cavitation extraction (NPCE), followed by liquid chromatography–tandem mass spectrometry (LC–MS/MS) is presented for the extraction and quantification of flavonoids in pigeon pea leaves. This method combines the high efficiency of NPCE and the sensitivity and accuracy of MS/MS. The influential parameters of the NPCE procedure including liquid/solid ratio, extraction time, nitrogen flow and number of extraction cycles were optimized. Under optimized conditions, the efficiency of NPCE for extracting five flavonoids was compared to microwave-assisted extraction (MAE), ultrasonic extraction (USE) and heating reflux extraction (HRE). Additionally, structural disruption to pigeon pea leaves samples with different extraction methods was investigated by scanning electron microscopy. The relative recovery with NPCE was equivalent to or higher than that with USE and obviously higher than those with MAE and HRE which are usually conducted in higher temperatures. Furthermore, because NPCE was performed with nitrogen at room temperature, the degradation and oxidation of analytes were avoided. In addition, the NPCE method was validated in terms of repeatability and reproducibility, relative standard deviation for relative recovery was lower than 5.84 and 8.83%, respectively. The method was also successfully applied for the quantification of five flavonoids in pigeon pea leaves. All these results suggest that the developed NPCE-LC–MS/MS method represents an excellent alternative for the extraction and quantification of flavonoids in other plant materials.     

Development and validation of a rapid multiresidue method for pesticide determination using gas chromatography-mass spectrometry: a realistic case in vineyard soils

A rapid and simultaneous method for residue identification and quantification for seven pesticides in agricultural soils has been developed to study a realistic situation in vineyard. The target compounds are two insecticides, two herbicides and three fungicides, from different chemical families. The procedure is based on a pressurized liquid extraction (PLE) with acetone, before a multiresidue GC-MS analysis. The recovery of PLE is between 53.8 ± 2.4 and 99.9 ± 4.4% according to pesticide. A limit of detection (LOD) between 1.4 and 4.6 μg kg⁻¹ of dry soil was obtained for five analytes. This procedure for testing soil contamination is sensitive and easy to perform.     

Surfactant-assisted pressurized liquid extraction for determination of flavonoids from Costus speciosus by micellar electrokinetic chromatography

Micellar electrokinetic chromatography (MEKC), a mode of capillary electrophoresis (CE), is considered an efficient analytical technique allowing for the reduction of organic solvent consumption during the experimental procedure. However, during sample preparation of natural products, the usage of large amount of organic solvent is generally unavoidable. In this article, therefore, a fast, simple, efficient, highly automatic and organic solvent-free sample preparation method, namely surfactant-assisted pressurized liquid extraction (PLE), was developed for the extraction of flavonoids in Costus speciosus flowers before MEKC analysis. The various experimental parameters such as the type and concentration of surfactant, and extraction time were evaluated systematically. Under the optimized conditions, the extraction efficiencies of surfactant-assisted PLE methods were comparable with Soxhlet extraction using organic solvent. The combination of surfactant-assisted PLE and MEKC was shown to be a green, rapid and effective approach for extraction and analysis of flavonoids in C. speciosus flowers.     

Selective pressurized liquid extraction of polybrominated diphenyl ethers in fish

A fast and simple method for the analysis of polybrominated diphenyl ethers (PBDEs) in fish samples was developed using a one-step extraction and clean-up by means of pressurized liquid extraction (PLE) combined with gas chromatography-ion trap tandem mass spectrometry (GC-ITMS-MS). The selective PLE method provided to obtain ready-to-analyse extracts without any additional clean-up step, using a sorbent as fat retainer inside the PLE cell. Several PLE operating conditions, such as solvent type, extraction temperature and time, number of cycles and type of fat retainer, were studied. Using Florisil as fat retainer, maximum recoveries of PBDEs (83-108%) with minimum presence of matrix-interfering compounds were obtained using a mixture of n-hexane:dichloromethane 90:10 (v/v) as solvent, an extraction temperature of 100 °C and a static extraction time of 5 min in combination with three static cycles. Quality parameters of the method were established using standards and fish samples. Limits of detection and quantification ranged from 10 to 34 pg g⁻¹ wet weight and between 34 and 68 pg g⁻¹ wet weight, respectively. In addition, good linearity (between 1 and 500 ng ml⁻¹) and high precision (RSD % < 15%) were achieved. The method was validated using the standard reference material SRM-1945 (whale blubber) and was then applied to the analysis of PBDEs in fish samples.     

Pressurized liquid extraction followed by high-performance liquid chromatography for determination of seven active compounds in Cortex Dictamni

A new method based on pressurized liquid extraction (PLE) followed by a sensitive and specific HPLC-DAD analysis is developed for determination of seven compounds in Cortex Dictamni. The operational parameters of PLE, such as extraction solvent, extraction temperature, extraction pressure, static extraction time, flush volume and extraction cycles were optimized, using the extraction efficiencies of dictamnine, obacunone and fraxinellone as targets. The optimized procedure employed MeOH as extraction solvent, 150 degrees C of extraction temperature, 1,500 psi extraction pressure, 5 min of static extraction time, 60% flush volume and the extraction recoveries of the three compounds were nearly to 100% for only one cycle. The following HPLC analysis was performed on a reversed-phase C(18) column with methanol-water as mobile phase in gradient manner, detected at 236 and 218 nm. The limits of detection (LOD) and limits of quantification (LOQ) of the seven compounds were in the range of 0.4-15.6 ng and 1.2-38.8 ng. This assay can be readily utilized as a quality control method for Cortex Dictamni and other related medicinal plants.     

Extraction of Astaxanthin from Shrimp Waste Using Pressurized Hot Ethanol

An efficient and environmentally sustainable extraction method is proposed for the enrichment of a high-value pigment, astaxanthin, from a low-value raw material, shrimp waste. Ethanol at elevated temperature and pressure was used as a “green” extraction solvent. An experimental design approach based on central composite design was used to investigate the dependence of pressurized liquid extraction (PLE) operating variables (pressure, temperature, extraction time) on the recovered astaxanthin concentration from shrimp waste. The results show that at a 95% confidence level, the most significant PLE operating variables were extraction temperature and time. Extraction pressure had only a minor effect on the astaxanthin recovery in the studied experimental conditions. The maximum astaxanthin recovery obtainable by PLE was calculated from the chemometrics results and then appraised by experiments. Our results show astaxanthin yields of around 24 mg kg^?1 shrimp waste. The reproducibility of the developed PLE method is good, showing a relative standard deviation of 3.5% (n = 6) for astaxanthin.     

Supercritical fluid extraction of Beauvericin from maize

Beauvericin (BEA), a supercritical fluid extraction with supercritical carbon dioxide from maize was investigated. Extraction efficiencies under several different extraction conditions were examined. Pressure, temperature, extraction time, organic modifier and water matrix content (10%) were investigated. The best extraction conditions were at a temperature of 60 °C, 3200 psi, for 30 min static extraction time and methanol as modifier solvent. Extraction recovery of 36% without modifier by adding water to the matrix in the extraction vessel (reproducibility relative standard deviations (R.S.D.)=3-5%) were recorded. Extraction recovery of 76.9% with methanol as co-solvent (reproducibility R.S.D.=3-5%) was obtained. Data shows that SFE gives a lower BEA recovery compared to conventional extraction protocol with organic solvents while SFE with modifier and conventional extraction yields are comparable. BEA extract contents were determined by high pressure liquid chromatography (HPLC) with a diode array detector (DAD) at 205 nm and BEA peak confirmed by LC-MS. Acetonitrile-water as mobile phase and column C-18 were both tested. Instrumental and analytical parameters were optimized in the range linear interval from 1 to 500 mg kg⁻¹ and reached a detection limit of 2 ng.     

Extraction and analysis of ochratoxin A in bread using pressurised liquid extraction and liquid chromatography

A pressurised liquid extraction (PLE) method for the analysis of ochratoxin A (OTA) in bread samples is given. Parameters such as solvent, temperature, pressure and time were investigated thoroughly. The optimized PLE conditions were: methanol as extraction solvent, 80 degrees C, 2000 psi and a 5-min cycle. OTA was determined by liquid chromatography coupled with fluorescence detection and confirmed by methyl ester derivatization. Under these conditions OTA recovery is 92.3% with a RSD of 5%. Limits of detection and quantification were 0.02 and 0.06 microg/kg, respectively. The proposed method was applied to 20 bread samples, finding two positive samples with OTA levels below the maximum permitted levels by the European Union.     

Determination of gastrodin and vanillyl alcohol in Gastrodia elata Blume by pressurized liquid extraction at room temperature

Pressurized liquid extraction (PLE) at room temperature with a laboratory-assembled system was applied for the extraction of gastrodin (GA) and vanillyl alcohol (VA) in Gastrodia elata Blume. The proposed system setup for this current work was simpler as no heating and backpressure regulator was required. Extraction with PLE was carried out dynamically at a flow rate of 1.5 mL/min, at room temperature, under an applied pressure of 10-20 bars with an extraction time of 40-50 min. The extraction efficiencies of the proposed method using 20% aqueous ethanol were compared with heating under reflux using organic solvents such as methanol and ethanol/water (20:80) for different batches of medicinal plant materials. For the determination of GA and VA in G. elata Blume, the extraction efficiencies of PLE at room temperature were observed to be comparable with heating under reflux. The method precision was found to vary from 1.6 to 8.6% (RSD, n = 6) on different days. The marker compounds present in the various medicinal plant extracts were determined by gradient elution HPLC and HPLC/MS/MS. Our work demonstrated the possibility of implementation of PLE at room temperature and the advantages of minimizing the use of organic solvents in the extraction process.     

Multi-residue method for trace level determination of pharmaceuticals in solid samples using pressurized liquid extraction followed by liquid chromatography/quadrupole-linear ion trap mass spectrometry

A simple and sensitive method for simultaneous analysis of 43 pharmaceutical compounds in sewage sludge and sediment samples was developed and validated. The target compounds were extracted using pressurized liquid extraction (PLE) and then purified and pre-concentrated by solid phase extraction (SPE) using a hydrophilic-lipophilic balanced polymer. PLE extraction was performed on temperature of 100 °C, with methanol/water mixture (1/2, v/v) as extraction solvent. The quantitative analysis was performed by liquid chromatography tandem mass spectrometry using a hybrid triple quadrupole-linear ion trap mass spectrometer (LC-QqLIT-MS). Data acquisition was carried out in selected reaction monitoring (SRM) mode, monitoring two SRM transitions to ensure an accurate identification of target compounds in the samples. Additional identification and confirmation of target compounds were performed using the Information Dependent Acquisition (IDA) function. The method was validated through the estimation of the linearity, sensitivity, repeatability, reproducibility and matrix effects. The internal standard approach was used for quantification because it efficiently corrected matrix effects. Despite the strong matrix interferences, the recoveries were generally higher of 50% in both matrixes and the detection and quantification limits were very low. Beside the very good sensitivity provided by LC-QqLIT-MS, an important characteristic of the method is that all the target compounds can be simultaneously extracted, treated and analysed. Hence, it can be used for routine analysis of pharmaceuticals providing large amount of data. The method was applied for the analysis of pharmaceuticals in river sediment and wastewater sludge from three treatment plants with different treatment properties (i.e. capacity, secondary treatment, quality of influent waters). The analysis showed a widespread occurrence of pharmaceuticals in the sludge matrices.     

Determination of N-nitroso derivatives of hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX) in soils by pressurized liquid extraction and liquid chromatography-electrospray ionization mass spectrometry

To aid in the evaluation of the potential toxicity of N-nitroso derivatives of hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX), we describe a pressurized liquid extraction (PLE) followed by liquid chromatography-electrospray ionization-mass spectrometry (LC-ESI-MS) method for determination of RDX and its N-nitroso derivatives: hexahydro-1-nitroso-3,5-dinitro-1,3,5-triazine (MNX), hexahydro-1,3-dinitroso-5-nitro-1,3,5-triazine (DNX), and hexahydro-1,3,5-trinitroso-1,3,5-triazine (TNX) in soils. Sandy loam soil was spiked with RDX and its N-nitroso derivatives (MNX, DNX, and TNX). Acetonitrile was used as the PLE extraction solvent at 100 degrees C and 1500 psi for 15 min. Florisil was used to cleanup extracts following PLE. Instrumental analysis employed LC-ESI-MS, in which 1mM acetic acid was added to the mobile phase to facilitate formation of acetate adduct ions [M+CH(3)COO](-). The method detection limits (MDLs) for RDX, MNX, DNX, and TNX were 1.46, 1.46, 1.69, and 1.93 ng/g, respectively. High recovery (91.1-108.3%), good precision (RSD: 3.2-12.4%), and reproducibility were achieved. This method proved effective and was applied to monitor the reductive biotransformation of MNX in soils with the presence of earthworms (Eisenia fetida).     

Optimizing pressurized liquid extraction of microbial lipids using the response surface method

Response surface methodology (RSM) was used for the determination of optimum extraction parameters to reach maximum lipid extraction yield with yeast. Total lipids were extracted from oleaginous yeast (Rhodotorula glutinis) using pressurized liquid extraction (PLE). The effects of extraction parameters on lipid extraction yield were studied by employing a second-order central composite design. The optimal condition was obtained as three cycles of 15 min at 100°C with a ratio of 144 g of hydromatrix per 100 g of dry cell weight. Different analysis methods were used to compare the optimized PLE method with two conventional methods (Soxhlet and modification of Bligh and Dyer methods) under efficiency, selectivity and reproducibility criteria thanks to gravimetric analysis, GC with flame ionization detector, High Performance Liquid Chromatography linked to Evaporative Light Scattering Detector (HPLC-ELSD) and thin-layer chromatographic analysis. For each sample, the lipid extraction yield with optimized PLE was higher than those obtained with referenced methods (Soxhlet and Bligh and Dyer methods with, respectively, a recovery of 78% and 85% compared to PLE method). Moreover, the use of PLE led to major advantages such as an analysis time reduction by a factor of 10 and solvent quantity reduction by 70%, compared with traditional extraction methods.     

Pressurized solvent extraction followed by gas chromatography tandem mass spectrometry for the determination of benzotriazole light stabilizers in indoor dust

A novel and sensitive method for the determination of five benzotriazole compounds (commonly used as light stabilizers) in indoor dust is presented. Pressurized liquid extraction (PLE) and gas chromatography followed by tandem in time mass spectrometry (GC–MS/MS) were used as sample preparation and determination techniques, respectively. Extraction and clean-up were integrated on-line and, after an evaporative concentration step, the extract provided by the PLE instrument was injected directly in the GC–MS/MS system. Parameters affecting the performance of the sample preparation process were evaluated using experimental factorial designs. Under optimized conditions, analytes were recovered from 0.5 g samples in 3 static extraction cycles of 10 min, using a hexane:dichloromethane (7:3) mixture, at 90 °C. Silica (1 g) was placed in the bottom of the extraction cells as clean-up sorbent. The recoveries of the method varied from 82 to 122%, with standard deviations below 13. The inter-day precision ranged from 9 to 12%, and the limits of quantification (LOQs) remained below 10 ng g⁻¹ for all species. For the first time, four of the five investigated species were found in dust from indoor environments. Their mean concentrations ranged from 71 to 780 ng g⁻¹.     

Pressurized liquid extraction of isoflavones from soybeans

Isoflavone derivatives from freeze-dried soybeans were extracted by pressurized liquid extraction (PLE) and determined by reverse-phase high performance liquid chromatography (HPLC) with both photo diode array and mass spectrometry (MS) detection. Both real and spiked samples were used in the development of the method.Several extraction solvents (methanol (MeOH) and ethanol (EtOH), 30-80% in water and water), temperatures (60-200 °C), pressures (100-200 atm), as well as the sample size (0.5-0.05 g) and cycle length (5-10 min) were studied for the optimization of the extraction protocol. The optimized extraction conditions for quantitative recoveries were: 0.1 g of sample, 100 °C, three (7 min) static extraction cycles and ethanol 70% as extracting solvent. The stability of the isoflavones during the PLE was also determined. Under PLE conditions, degradation of malonyl glucoside forms of the isoflavones takes place using temperatures higher than 100 °C whereas degradation of glucosides takes place above 150 °C. Using the optimized protocol, isoflavones can be extracted from freeze-dried soybeans without degradation.     

Extraction of polycyclic aromatic hydrocarbons and organochlorine pesticides from soils: a comparison between Soxhlet extraction, microwave-assisted extraction and accelerated solvent extraction techniques

The methods of simultaneous extraction of polycyclic aromatic hydrocarbons (PAHs) and organochlorine pesticides (OCPs) from soils using Soxhlet extraction, microwave-assisted extraction (MAE) and accelerated solvent extraction (ASE) were established, and the extraction efficiencies using the three methods were systemically compared from procedural blank, limits of detection and quantification, method recovery and reproducibility, method chromatogram and other factors. In addition, soils with different total organic carbon contents were used to test the extraction efficiencies of the three methods. The results showed that the values obtained in this study were comparable with the values reported by other studies. In some respects such as method recovery and reproducibility, there were no significant differences among the three methods for the extraction of PAHs and OCPs. In some respects such as procedural blank and limits of detection and quantification, there were significant differences among the three methods. Overall, ASE had the best extraction efficiency compared to MAE and Soxhlet extraction, and the extraction efficiencies of MAE and Soxhlet extraction were comparable to each other depending on the property such as TOC content of the studied soil. Considering other factors such as solvent consumption and extraction time, ASE and MAE are preferable to Soxhlet extraction.     

Determination of tocopherols and tocotrienols in cereals by pressurized liquid extraction-liquid chromatography-mass spectrometry

A rapid analytical method including pressurized liquid extraction (PLE) and liquid chromatography-electrospray ionisation-mass spectrometry (LC-ESI-MS) has been developed for the determination of tocopherols and tocotrienols in cereals. The pressurized liquid extraction parameters were optimized in order to maximize the extraction efficiency. The use of methanol as extraction solvent at a temperature of 50 °C and a pressure of 110 bar, using one cycle of extraction with a static time of 5 min, provided the best results. A good LC separation was achieved using a C₁₈ column and a solution of 6.0 mM ammonia in methanol/water (97:3, v/v) as the mobile phase at a flow rate of 0.2 mL min⁻¹. MS coupling with an ESI interface in the negative ion mode was used as the detection technique. In the present work, it is shown that the addition of a base to the mobile phase is required to enhance the ionization of tocopherols and tocotrienols in negative ion mode electrospray ionization. The applicability of the method to cereal samples was confirmed. The reproducibility of the procedure was good, with relative standard deviations in the 6-10% range. The recoveries of added tocopherols from cereal samples ranged from 91 to 109%.