Silver(I) ions-enhanced electrochemiluminescence of tris(2,2-bipyridyl)ruthenium(II)

In this paper, we demonstrate an electrochemiluminescence (ECL) enhancement of tris(2,2-bipyridyl)ruthenium(II) (Ru(bpy)₃²⁺) by the addition of silver(I) ions. The maximum enhancement factor of about 5 was obtained on a glassy carbon electrode in the absence of co-reactant. The enhancement of ECL intensity was possibly attributed to the unique catalytic activity of Ag⁺ for reactions between Ru(bpy)₃³⁺ with OH. The higher enhancement was observed in phosphate buffer solutions compared with that from borate buffer solutions. This resulted from the fact that formation of nanoparticles with large surface area in the phosphate buffer solution exhibited high catalytic activity. The amount of Ag⁺, solution pH and working electrode materials played important roles for the ECL enhancement. We also studied the effects of Ag⁺ on Ru(bpy)₃²⁺/tripropylamine and Ru(bpy)₃²⁺/C₂O₄²⁻ ECL systems.     

Tris(2,2′-bipyridyl)ruthenium(II) electrogenerated chemiluminescence sensor based on carbon nantube dispersed in sol-gel-derived titania-Nafion composite films

A highly sensitive and stable tris(2,2′-bipyridyl)ruthenium(II) (Ru(bpy)₃²⁺) electrogenerated chemiluminescence (ECL) sensor was developed based on carbon nanotube (CNT) dispersed in mesoporous composite films of sol-gel titania and perfluorosulfonated ionomer (Nafion). Single-wall (SWCNT) and multi-wall carbon nanotubes (MWCNT) can be easily dispersed in the titania-Nafion composite solution. The hydrophobic CNT in the titania-Nafion composite films coated on a glassy carbon electrode certainly increased the amount of Ru(bpy)₃²⁺ immobilized in the ECL sensor by adsorption of Ru(bpy)₃²⁺ onto CNT surface, the electrocatalytic activity towards the oxidation of hydrophobic analytes, and the electronic conductivity of the composite films. Therefore, the present ECL sensor based on the CNT-titania-Nafion showed improved ECL sensitivity for tripropylamine (TPA) compared to the ECL sensors based on both titania-Nafion composite films without CNT and pure Nafion films. The present Ru(bpy)₃²⁺ ECL sensor based on the MWCNT-titania--Nafion composite gave a linear response (R² = 0.999) for TPA concentration from 50 nM to 1.0 mM with a remarkable detection limit (S/N = 3) of 10 nM while the ECL sensors based on titania-Nafion composite without MWCNT, pure Nafion films, and MWCNT-Nafion composite gave a detection limit of 0.1 μM, 1 μM, and 50 nM, respectively. The present ECL sensor showed outstanding long-term stability (no signal loss for 4 months).     

Flow injection chemiluminescence determination of carbaryl using photolytic decomposition and photogenerated tris (2,2′-bipyridyl)ruthenium(III)

A flow injection (FI) system combined with two photochemical processes is developed for the sensitive and rapid determination of carbaryl. It is based on the on-line photo-conversion of carbaryl into methylamine which subsequently reacts with Ru(bpy)₃³⁺ generated through the on-line photo-oxidation of Ru(bpy)₃²⁺ with peroxydisulphate. The linear concentration range of application was 0.04-4.0 μg ml⁻¹ of carbaryl, with an R.S.D. of 1.2% (for a level of 0.50 μg ml⁻¹) and a detection limit of 0.012 μg ml⁻¹. The sample throughput was 200 injections per hour. The applicability of the method was demonstrated by determining carbaryl in commercial formulations, water, soil, grain and blood serum.     

Electrochemiluminescence sensor using tris(2,2′-bipyridyl)ruthenium(II) immobilized in Eastman-AQ55D–silica composite thin-films

An electrochemiluminescence (ECL) sensor with good long-term stability and fast response time has been developed. The sensor was based on the immobilization of tris(2,2′-bipyridyl)ruthenium(II) (Ru(bpy)₃²⁺) into the Eastman-AQ55D–silica composite thin films on a glassy carbon electrode. The ECL and electrochemistry of Ru(bpy)₃²⁺ immobilized in the composite thin films have been investigated, and the modified electrode was used for the ECL detection of oxalate, tripropylamine (TPA) and chlorpromazine (CPZ) in a flow injection analysis system and showed high sensitivity. Because of the strong electrostatic interaction and low hydrophobicity of Eastman-AQ55D, the sensor showed no loss of response over 2 months of dry storage. In use, the electrode showed only a 5% decrease in response over 100 potential cycles. The detection limit was 1 μmol l⁻¹ for oxalate and 0.1 μmol l⁻¹ for both TPA and CPZ (S/N=3), respectively. The linear range extended from 50 μmol l⁻¹ to 5 mmol l⁻¹ for oxalate, from 20 μmol l⁻¹ to 1 mmol l⁻¹ for TPA, and from 1 μmol l⁻¹ to 200 μmol l⁻¹ for CPZ.     

Disposable biosensor based on cathodic electrochemiluminescence of tris(2,2-bipyridine)ruthenium(II) for uric acid determination

A new method for uric acid (UA) determination based on the quenching of the cathodic ECL of the tris(2,2-bipyridine)ruthenium(II)–uricase system is described. The biosensor is based on a double-layer design containing first tris(2,2-bipyridine)ruthenium(II) (Ru(bpy)₃²⁺) electrochemically immobilized on graphite screen-printed cells and uricase in chitosan as a second layer. The uric acid biosensing is based on the ECL quenching produced by uric acid over the cathodic ECL caused by immobilized Ru(bpy)₃²⁺ in the presence of uricase. The use of a −1.1 V pulse for 1 s with a dwelling time of 10 s makes it possible to estimate the initial enzymatic rate, which is used as the analytical signal. The Stern–Volmer type calibration function shows a dynamic range from 1.0 × 10⁻⁵ to 1.0 × 10⁻³ M with a limit of detection of 3.1 × 10⁻⁶ M and an accuracy of 13.6% (1.0 × 10⁻⁴ M, n = 5) as relative standard deviation. Satisfactory results were obtained for urine samples, creating an affordable alternative for uric acid determination.     

十二烷基磺酸钠-盐酸维拉帕米-联吡啶钌体系电化学发光及其应用

在十二烷基磺酸钠(SDS)中,考察了盐酸维拉帕米-Ru(bpy)3(2+)体系在金电极上的电化学及其发光行为.结果表明:SDS对体系的电化学反应和电化学发光强度具有显著的增敏作用.据此,建立了一种高效、简便的测定盐酸维拉帕米的电化学发光新方法.在最佳实验条件下,盐酸维拉帕米浓度在1.0×10(-4)～1.0×10(-2...     

Tris(2,2′-bipyridyl)cobalt(III)-doped silica nanoparticle DNA probe for the electrochemical detection of DNA hybridization

A new and sensitive electrochemical DNA hybridization detection assay, using tris(2,2′-bipyridyl)cobalt(III) [Co(bpy)₃³⁺]-doped silica nanoparticles as the oligonucleotide (ODN) labeling tag, and based on voltammetric detection of Co(bpy)₃³⁺ inside silica nanoparticles, is described. Electro-active Co(bpy)₃³⁺ is not possible for directly linking with DNA, it is doped into the silica nanoparticles in the process of nanoparticles synthesis for DNA labeling with trimethoxysilylpropydiethylenetriamine (DETA) and glutaraldehyde as linking agents. The Co(bpy)₃³⁺ labeled DNA probe is used to hybridize with target DNA immobilized on the surface of glassy carbon electrode. Only the complementary sequence DNA (cDNA) could form a double-stranded DNA (dsDNA) with the DNA probe labeled with Co(bpy)₃³⁺ and give an obvious electrochemical response. A three-base mismatch sequence and non-complementary sequence had negligible response. Due to the large number of Co(bpy)₃³⁺ molecules inside silica nanoparticles linked to oligonucleotide DNA probe, the assay showed a high sensitivity. It allows the detection at levels as low as 2.0×10⁻¹⁰ mol l⁻¹ of the target oligonucleotides.     

Determination of proline in wine using flow injection analysis with tris(2,2'-bipyridyl)ruthenium(II) chemiluminescence detection

Flow injection methodology is described for the determination of proline in red and white wines using tris(2,2′-bipyridyl)ruthenium(II) chemiluminescence detection. Selective conditions were achieved for proline at pH 10, while other amino acids and wine components did not interfere. The precision of the method was less than 1.00% (R.S.D.) for five replicates of a standard (4 × 10⁻⁶ M) and the detection limit was 1 × 10⁻⁸ M. The level of proline in white and sparkling wines using the developed methodology was equivalent to those achieved using HPLC-FMOC amino acid analysis. SPE removal of phenolic material was required for red wines to minimize Ru(bipy)₃³⁺ consumption and its associated effect on accuracy.     

Determination of sulfur contents of SO3, S2O3 and S based on the electrocatalytic interaction with homogeneous mediator tris(2,2'-bipyridyl)Ru(II)

A sensitive voltammetric method has been developed for the determination of total or single species of sulfur anions containing sulfide, sulfite and thiosulfate. The method is based on the catalytic effect of tris(2,2'-bipyridyl)Ruthenium(II) (Ru(bpy)₂^+ 2) as a homogeneous mediator on the oxidation of those anions at the surface of a glassy carbon electrode. A reversible redox couple of Ru(II)/Ru(III) were observed as a solute in aqueous solution. Cyclic voltammetry study showed that the catalytic current of the system depends on the concentration of the anions. Optimum pH values for voltammetric determination of sulfite, thiosulfate and sulfide has been found to be 5.6, 10.0 and 10.0, respectively. Under the optimized conditions the calibration curves have been obtained linear in the concentration ranges of 0.8–500.0, 0.4–1000.0 and 0.5–5000.0 µmol L^− 1 of SO₃²⁻, S₂O₃²⁻ and S²⁻, respectively. The detection limits have been calculated to be 0.40, 0.17 and 0.33 µmol L^− 1 for SO₃²⁻, S₂O₃²⁻ and S²⁻, respectively. The diffusion coefficients of sulfite and thiosulfate have been estimated using chronoamperometry. The chronoamperometric method also has been used to determine the catalytic rate constant for catalytic reaction of the Ru(bpy)₂^+ 2 with sulfite and thiosulfate. Finally the proposed method has been used for the determination of total sulfur contents in real samples of water and wastewater. Moreover the sulfite content in sugar and sulfur dioxide in air has been determined with satisfactory results.     

Solid-state electrochemiluminescence sensor through the electrodeposition of Ru(bpy)3/AuNPs/chitosan composite film onto electrode

Tris(2,2′-bipyridyl)ruthenium(II) (Ru(bpy)₃²⁺) has been successfully immobilized onto electrode through the electrodeposition of Ru(bpy)₃²⁺/AuNPs/chitosan composite film. In the experiments, chitosan solution was first mixed with Au nanoparticles (AuNPs) and Ru(bpy)₃²⁺. Then, during chronopotentiometry experiments in this mixed solution, a porous 3D network structured film containing Ru(bpy)₃²⁺, AuNPs and chitosan has been electrodeposited onto cathode due to the deposition of chitosan when pH value is over its pK_a (6.3). The applied current density is crucial to the film thickness and the amount of the entrapped Ru(bpy)₃²⁺. Additionally, these doping Ru(bpy)₃²⁺ in the composite film maintained their intrinsic electrochemical and electrochemiluminescence activities. Consequently, this Ru(bpy)₃²⁺/AuNPs/chitosan modified electrode has been used in ECL to detect tripropylamine, and the detection limit was 5 × 10⁻¹⁰ M.     

Electrochemiluminescence immunosensor for ultrasensitive detection of biomarker using Ru(bpy)3-encapsulated silica nanosphere labels

Here, we describe a new approach for electrochemiluminescence (ECL) assay with Ru(bpy)₃²⁺-encapsulated silica nanoparticle (SiO₂@Ru) as labels. A water-in-oil (W/O) microemulsion method was employed for one-pot synthesis of SiO₂@Ru nanoparticles. The as-synthesized SiO₂@Ru nanoparticles have a narrow size distribution, which allows reproducible loading of Ru(bpy)₃²⁺ inside the silica shell and of α-fetoprotein antibody (anti-AFP), a model antibody, on the silica surface with glutaraldehyde as linkage. The silica shell effectively prevents leakage of Ru(bpy)₃²⁺ into the aqueous solution due to strong electrostatic interaction between the positively charged Ru(bpy)₃²⁺ and the negatively charged surface of silica. The porous structure of silica shell allowed the ion to move easily through the pore to exchange energy/electrons with the entrapped Ru(bpy)₃²⁺. The as-synthesized SiO₂@Ru can be used as a label for ultrasensitive detection of biomarkers through a sandwiched immunoassay process. The calibration range of AFP concentration was 0.05-30 ng mL⁻¹ with linear relation from 0.05 to 20 ng mL⁻¹ and a detection limit of 0.035 ng mL⁻¹ at 3σ. The resulting immunosensors possess high sensitivity and good analytical performance.     

The Factors Affecting the Electrochemiluminescence of Tris(2,2′‐bipyridyl)Ruthenium(II)/Tertiary Amines

Factors affecting tris(2,2′‐bipyridyl) ruthenium(II) (Ru(bpy)₃²⁺)/tertiary amine electrochemiluminescence (ECL) were investigated in the present work with several tertiary amines as coreactants. Some new phenomena different to those of traditional Ru(bpy)₃²⁺/tripropylamine were observed, such as the different responses of different coreactants to the hydrophobic nature of the working electrode and the ECL emission of triethanolamine at 0.85 V. The pK_a value (acid dissociation constant) for the deprotonation of tertiary amine group in the coreactant molecules and solubility of coreactants affect the ECL profiles vs. electrolyte pH. Moreover, the solubility of coreactants is also related to the ECL response to the addition of surfactants and electrode hydrophobic nature. Investigation of the effects of molecular structures indicated that molecules restricting the formation of the trigonal planar structure of the active radical in the electrooxidation procedure resulted in low ECL emission. The behaviors of hydroxyl and carboxylic group as substituents of α‐carbon are also totally different to the traditional opinions about the ECL from Ru(bpy)₃²⁺/tertiary amines.     

Can clay emit light? Ru(bpy)3-modified clay colloids and their application in the detection of glucose

In this paper, we describe the electrochemiluminescent (ECL) behavior of Ru(bpy)₃³⁺-incorporated clay colloids. Experimental results based on the electrochemical-quartz-crystal-microbalance (EQCM) techniques showed that Ru(bpy)₃³⁺ could be adsorbed by the clay colloids (montmorillonite K10, denoted K10). The resulting clay particles could emit light (λ_em 610 nm) when they were fabricated as thin films sandwiched by two conductive ITO electrodes with opposite biases. These Ru(bpy)₃³⁺-incorporated clay-modified electrodes could also emit light in aqueous oxalate solutions (pH 10) when potentials more positive than 0.9 V vs. SCE were applied. EDTA was an effective promoter for the Ru(bpy)_{3 (clay)}³⁺-oxalate ECL reaction. The resulting ECL showed a remarkable sensitivity to oxygen. A glucose optrode was thus fabricated based on the Ru(bpy)₃³⁺-incorporated K10 colloids and glucose oxidase (GOx). The ECL signals behaved as a function of [glucose], covering a range from 0.1 to 10 mM at pH 10. The detection limits reached a level of 0.1 mM at this pH.     

玻碳电极上Ru(bpy)32+的吸附及其电致化学发光的研究

通过电化学循环伏安法和电致化学发光方法, 研究了Ru(bpy)₃²⁺在玻碳电极上的吸附, 研究结果表明, Ru(bpy)₃²⁺的浓度和与玻碳材料接触的时间, 直接影响了Ru(bpy)₃²⁺在玻碳上的吸附. 还考察了吸附的 在玻碳电极上被氧化后脱附的情况.     

Evaluation of tris(4,7-diphenyl-1,10-phenanthrolinedisulfonate)ruthenium(II) as a chemiluminescence reagent

Previous studies have suggested that tris(4,7-diphenyl-1,10-phenanthrolinedisulfonate)ruthenium(II) (Ru(BPS)₃⁴⁻) has great potential as a chemiluminescence reagent in acidic aqueous solution. We have evaluated four different samples of this reagent (two commercially available and two synthesised in our laboratory) in comparison with tris(2,2′-bipyridine)ruthenium(II) (Ru(bipy)₃²⁺) and tris(1,10-phenanthroline)ruthenium(II) (Ru(phen)₃²⁺), using a range of structurally diverse analytes. In general, Ru(BPS)₃⁴⁻ produced more intense chemiluminescence, but the oxidised Ru(BPS)₃³⁻ species is less stable in aqueous solution than Ru(bipy)₃³⁺ and produced a greater blank signal than Ru(bipy)₃³⁺ or Ru(phen)₃³⁺, which had a detrimental effect on sensitivity. Although the complex is often depicted with the sulfonate groups of the BPS ligand in the para position on the phenyl rings, NMR characterisation revealed that the commercially available BPS material used in this study was predominantly the meta isomer.     

Effect of oxidant type on the chemiluminescence intensity from the reaction of tris(2,2′-bipyridyl)ruthenium(III) with various organic acids

An investigation into the chemiluminescence of fourteen organic acids and tris(2,2′-bipyridyl)ruthenium(II) was undertaken. Particular emphasis was placed upon the method of production of the reagent, tris(2,2′-bipyridyl)ruthenium(III), with cerium(IV) sulfate, potassium permanganate, lead dioxide and electrochemical generation. Analytically useful chemiluminescence was observed when Ce(IV) or potassium permanganate were employed as oxidants. The kinetics of analyte oxidation was related to the intensity of the chemiluminescence emission, which increased by three orders of magnitude for tartaric acid after 40 h of oxidation.     

3D nanostructured Ni(OH)2 microspheres as an efficient immobilization matrix of Ru(bpy)3 for high-performance electrochemiluminescence sensor

The electrochemistry and electrochemiluminescence (ECL) of novel three-dimensional nanostructured Ru(bpy)₃²⁺/Ni(OH)₂ microspheres were investigated for the first time. The negatively charged porous Ni(OH)₂ microspheres composed of Ni(OH)₂ nanowires were specifically designed to interact with Ru(bpy)₃²⁺. The large surface area and porous structure of Ni(OH)₂ microspheres enhance loading of Ru(bpy)₃²⁺ and mass transport of the model analyte, tripropylamine (TPA). Excellent ECL performance of the presented sensor was achieved including good stability and wide linear range from 7.7 × 10⁻¹⁰ to 3.8 × 10⁻³ M with the detection limit of 2.6 × 10⁻¹⁰ M to TPA.