The heat transfer performance and entropy analysis are done in a compact loop heat pipe (CLHP) with Al2O3/water and Ag/water nanofluid. A compact loop heat pipe having a flat square evaporator with dimensions of 34 mm (L)?×?34 mm (W)?×?19 mm (H) has been fabricated and tested for the heat load ranging from 30 to 500 W. The experimental tests are conducted by keeping the CLHP in the vertical orientation with distilled water, silver (Ag)/water and aluminium oxide (Al2O3)/water nanofluid having low volume concentrations of (0.09% and 0.12%). The effect of wall and vapour temperature, evaporator and condenser heat transfer coefficient, thermal resistance on the applied heat loads is experimentally investigated and compared. The experimental results showed that the evaporator thermal resistance is reduced by 34.70% and 20.21%, respectively, for 0.12 vol% of Ag, Al2O3 nanoparticles when compared with that of the distilled water. For the same volume concentrations of Ag, Al2O3 nanoparticles, an enhancement of 34.52%, 23.7%, 39.27% and 30.8%, respectively, observed for the convective heat transfer coefficients at the evaporator and condenser. The entropy is also reduced by 19.08% and 11.58% when Ag and Al2O3 nanofluids are used as the operating fluid. From the experimental tests, it is found that the addition of small amount of Ag nanoparticles in the working fluid enhanced the operating range by 15% when compared with that of Al2O3/water nanofluid without the occurrence of any dry-out conditions.
相似文献High-performance cooling is of vital importance for the cutting-edge technology of today, from nanoelectronic mechanical systems to nuclear reactors. Advances in nanotechnology have allowed the development of a new category of coolants, termed nanofluids that have the potential to enhance the thermal performance of conventional heat transfer fluids. At the present time, nanofluids are a controversial research theme, since there is yet no conclusive answer to explain the underlying physical mechanisms of heat transfer. The current study investigates experimentally the heat and mass transfer behaviour of dilute Al2O3–H2O nanofluids under turbulent natural convection—Rayleigh number of the order of 109—in a cubic Rayleigh–Bénard cell with optical access. Traditional heat transfer measurements were combined with a velocimetry method to obtain a deeper understanding of the impact of nanoparticles on the heat transfer performance of the base fluid. Particle image velocimetry was employed to quantify the resulting mean velocity field and flow structures in dilute nanofluids under natural convection, at three parallel planes inside the cubic cell. All the results were compared with that for the base fluid, i.e. deionised water. It was observed that the presence of a minute amount of Al2O3 nanoparticles in deionised water, φv =?0.00026 vol.%, considerably modifies the mass transfer behaviour of the fluid in the bulk region of turbulent Rayleigh–Bénard convection. Simultaneously, the general heat transport, as expressed by the Nusselt number, remained unaffected within the experimental uncertainty.
相似文献In the present study, heat transfer and fluid flow of a pseudo-plastic non-Newtonian nanofluid over permeable surface has been solved in the presence of injection and suction. Similarity solution method is utilized to convert the governing partial differential equations into ordinary differential equations, which then is solved numerically using Runge–Kutta–Fehlberg fourth–fifth order (RKF45) method. The Cu, CuO, TiO2 and Al2O3 nanoparticles are considered in this study along with sodium carboxymethyl cellulose (CMC)/water as base fluid. Validation has been done with former numerical results. The influence of power-law index, volume fraction of nanoparticles, nanoparticles type and permeability parameter on nanofluid flow and heat transfer was investigated. The results of the study illustrated that the flow and heat transfer of non-Newtonian nanofluid in the presence of suction and injection has different behaviors. For injection and the impermeable plate, the non-Newtonian nanofluid shows a better heat transfer performance compared to Newtonian nanofluid. However, changing the type of nanoparticles has a more intense influence on heat transfer process during suction. It was also observed that in injection, contrary to the other two cases, the usage of non-Newtonian nanofluid can decrease heat transfer in all cases.
相似文献Nanofluids of Li2CO3–Na2CO3–K2CO3 improved by three nano-Al2O3 samples are firstly prepared by means of two-step aqueous method to enhance thermal properties for high-temperature heat transfer, when used as heat transfer fluids and thermal energy systems for concentrating solar power systems. Specific heat of ternary carbonates containing Al2O3 of 0.2, 0.4, 0.8, 1.0, 1.4 and 2.0 mass% is measured, and nanofluids with 1.0 mass% of 20-nm Al2O3, 1.0 mass% of 50-nm Al2O3 and 0.8 mass% of 80-nm Al2O3 are selected as superior candidates. The maximum enhancement of specific heat is 18.5% in solid and 33.0% in liquid, 17.9% in solid and 22.7% in liquid, 13.2% in solid and 17.5% in liquid for nanofluids containing 20-, 50- and 80-nm Al2O3. Thermal conductivity is, respectively, improved by 23.3, 28.5 and 30.9% under the addition of Al2O3. New chemical bonds and crystals are scarcely formed in composites through FT-IR and XRD determination. SEM images certify that nano-Al2O3 are homogeneously mixed into nanofluids and this structure may be a critical incentive for enhancing thermal properties. There are no significant changes with respect to the heat flow, melting/freezing point and latent heat after the 30 circles of determination. Briefly, it can be speculated that these nanofluids will exhibit tremendous potential in the coming applications of heat transfer and thermal storage for concentrating solar power systems.
相似文献Current investigation aims to analyze the conjugate free convection inside a porous square cavity occupied with Ag–MgO hybrid nanofluid using the local thermal non-equilibrium (LTNE) model. Hybrid nanofluids are a novel kind of enhanced working fluids, engineered with enhanced thermo-physical and chemical properties. Two solid walls located between the horizontal bounds in two sides of cavity play the role of a conductive interface between the hot and cold walls, and moreover, the top and bottom bounds have been insulated. The governing differential equations are obtained by Darcy model and then for better representation of the results, converted into a dimensionless form. The finite element method is utilized to solve the governing equations. To evaluate the correctness and accuracy of the results, comparisons have been performed between the outcomes of this work and the previously published results. The results indicate that using the hybrid nanoparticles decreases the flow strength and the heat transfer rate. The heat transfer rate augments when Rk rises and the flow strength augments when Ra grows. Enhancing the porosity increases strongly the size and strength of the vortex composed inside the porous medium. When Kr is low, the heat transfer rate is low and by increasing Kr, thermal fields become closer to each other. The effect of hybrid nanoparticles on thermal fields with the thinner solid walls is more than that the thicker ones. An increment in H eventuates the enhancement of heat transfer and hence, the thermal boundary layer thickness. By increasing the volume fraction of the hybrid nanoparticles, Nuhnf and Nus decrease in constant Ra. Besides, increase in Ra enhances the Nuhnf and Nus. For a certain d, the reduction of Nus due to using the hybrid nanoparticles is more than that for Nuhnf. The increment of d lessens Nuhnf for all values of Kr and has not specific trends for Nus. Utilizing hybrid nanoparticles decreases Nus (except d?=?0.4), rises Nus when Kr?<?18, while it can increase Nus for Kr?>?42. In constant d, increment of H, respectively, decreases and boosts Nuhnf and Nus. For all values of d, increment of ε declines Nuhnf. In low value of d, the increase in ε reduces Nus, whereas at higher values, Nus has continuously enhancing trend. For different values of d, the increase in ε scrimps Nuhnf. The increment of d and also ε, and H are, respectively, decreases and increases the heat transfer rate.
相似文献In this numerical study, laminar flow of water nanofluid/GNP–SDBS (graphene nanoplatelet–sodium dodecylbenzene sulfonate) for 0–0.1% solid nanoparticles mass fraction was investigated for Reynolds numbers of 50–1000 in 3D space via finite volume method. In the newly proposed microchannel design, the cooling fluid is moving in countercurrent in the upper and lower layers of the microchannels, and there are cavities and sinusoidal routes on the solid walls of the microchannel, and the presence of rectangular ribs on the flow centerline along the fluid path enhances mixing for cooling fluid and creates better heat transfer for warm surfaces. The results of this study show that this special design of the microchannel can have a substantial increase in Nusselt number and heat transfer so that in the considered geometry by adding solid nanoparticles mass fraction it is possible to increase average Nusselt number for each Reynolds number by approximately 20%. Also, the mixing of the fluid because of formation of secondary flows has a strong effect on making the temperature distribution uniform in the cooling fluid and solid bed (wall) of the microchannel, especially in the lower layer. The upper layer of the microchannel always has a lower temperature due to indirect contact with heat flux compared with the lower layer. In this study, by increasing Reynolds number and mass fraction of solid nanoparticles the Nusselt number is increased and heat resistance of the lower wall of the microchannel is reduced. Based on the investigation of flow field and heat transfer, the use of the proposed design of the microchannel is recommended for Reynolds number less than 300.
相似文献The main purpose of this study is numerically investigating the flow and heat transfer of nanofluid flow inside a microchannel with L-shaped porous ribs as well as studying the effect of porous media properties on the performance evaluation criterion (PEC) of the fluid. In the present paper, in addition to the pure water fluid, the effect of using water/CuO nanofluid on the PEC of microchannel was investigated. The flow was simulated in four Reynolds numbers and two different volume fractions of nanoparticles in laminar flow regime. The investigated parameters are the thermal conductivity and the porosity rate of porous medium. The results indicate that with the existence of porous ribs, the nanofluid does not have a significant effect on heat transfer increase. By using porous ribs in flow with Reynolds number of 1200, the heat transfer rate increases up to 42% and in flow with Reynolds number of 100, this rate increases by 25%.
相似文献In this research, three different volume concentrations (??=?0.05, 0.1 and 0.2%) of Al2O3/water, CuO/water and Al2O3–CuO/water (50:50) nanofluids are prepared by adopting a two-step nanofluid preparation method. Al2O3 and CuO nanoparticles with the average diameter of 50 nm and 27 nm were dispersed in distilled water. The thermal conductivity and viscosity of prepared nanofluids are measured for different temperatures by using KD2 Pro thermal property analyzed and Brookfield viscometer, respectively. The effects of nanofluids on the thermal, electrical and overall efficiency of photovoltaic thermal (PVT) solar collector are also studied. The experimental results revealed that the thermal conductivity and viscosity increase with the increase in percentage volume concentration and viscosity decreases with the increase in temperature. Furthermore, the obtained maximum thermal and electrical efficiencies of a PVT solar collector for 0.2% volume concentration of hybrid nanofluids are 82% and 15%, respectively, at peak solar radiation. The highest overall efficiency of a PVT collector with .2% volume concentration of hybrid nanofluid was 97% at peak solar radiation. Results recommend that nanofluids can be used as a heat transfer in PVT solar collector.
相似文献Turbulent flow characteristics and heat transfer applications of a twisted heat exchanger with 3-lobed cross section along with Y-tape insert are numerically studied. The working fluids for the simulations are pure water and water–Al2O3 nanofluid using two-phase mixture model. The study is carried out for various nanofluid volume fractions of 0.01, 0.02 and 0.03 with Reynolds number in the range of 5000–20,000. The effect of nanoparticles in heat transfer augmentation for smooth and lobed tubes is discussed based on presenting the highest thermal performance, which is a relation between heat transfer rate and pressure loss. Results show that implementing the twisted tube with Y-tape insert enhances the heat transfer more than the twisted tube. Relative Nusselt numbers for twisted tubes decrease with Reynolds number in comparison with the plain tube. Turbulent intensity, swirl number and tangential velocity of twisted tube with insert are higher than empty twisted tube indicating that inserting the Y-tape intensifies the turbulence and disturbs the fluid flow further. On the other hand, although the twisted tube increases the pressure drop more than plain tube, the case with Y-tape drastically increases the friction factor. So, the thermal performance of twisted tube with insert is lower than empty twisted tube. Adding nanoparticles to the base fluid has different influence on the investigated cases. It augments the relative Nusselt number inside plain tube and empty twisted tube with slight increment in friction factor. Increasing the nanoparticles concentration enhances the heat transfer rates for these cases while it does not increase the relative Nusselt number inside twisted tube with Y-tape insert at high Reynolds number and nanoparticle concentration. Moreover, it can be found that twisted tube with or without Y-tape insert is more efficient at low Reynolds number in comparison with the plain tube.
相似文献Fluid atomic behavior is an important factor for industrial applications. Computer simulations based on simple models predict Poiseuille flow for these atomic structures with the presence of external force. In this work, we describe the dynamical properties of Ar and O2 flows with precise atomic arrangement via dissipative particle dynamics (DPD) and molecular dynamics (MD) simulation approaches. In these methods, each model is represented by using Large-scale Atomic/Molecular Massively Parallel Simulator package. Simulation results show that maximum rate for velocity of Ar flow in platinum and copper microchannels is 0.100 (unit less)/0.091 Å ps?1 and 0.121 (unit less)/0.105 Å ps?1 by using DPD/MD approach. This atomic parameter changes to 0.111 (unit less)/0.102 Å ps?1 and 0.125 (unit less)/0.108 Å ps?1 for O2 fluid with mentioned approaches. By decreasing the microchannel size, the maximum rate of velocity reaches to 0.101 (unit less)/0.099 Å ps?1 and maximum temperature rate decreases to 485 (unit less)/440 K with DPD/MD approaches. These calculated parameters can be used in industrial application designing for some processes such as heat transfer in structures. It was seen that the developed DPD approach was able to simulate the fluid flow and heat transfer of various types of fluids at micro- and nanoscales with suitable accuracy versus MD.
相似文献A numerical analysis was carried out of mixed convection heat transfer for a laminar flow in a rectangular inclined microchannel totally filled with a water/Al2O3 nanofluid. The governing conservation equations are translated into a dimensionless form using the thermal single relaxation time and they modify the lattice Boltzmann method with double distribution functions. The viscous dissipation effects are adapted to the energy equation. The effects of nanoparticle volume fractions ? (0?≤???≤?0.04) and inclination angles γ (0°?≤?γ?≤?60°) on the flow of the nanofluid and the heat transfer are investigated. The obtained results are presented in terms of streamlines, isotherms, slip velocity, wall temperature and Nusselt number. The results show that the higher values of the volume fraction of Al2O3 and the large values of inclination angles improve the heat transfer rate.
相似文献Melted and heat treated samples (900° C) of the system: Li2O–Al2O3–GeO2 have been examined by X-rays. In the region between Li0.9Al0.9Ge2.1O6 and Li1.4Al1.4Ge1.6O6 a new phase having a high-quartz type structure has been detected. GeO2 (low-quartz type) dissolves LiAlO2 up to 5 mole%;H-LiAlO2 andH-LiAl5O8 (spinel) dissolve a significant amount of GeO2. The existence of the phenacite-like phase LiAlGeO4 has been confirmed.
Mit 1 Abbildung 相似文献
Reproducible measurements, reliable results and 1st order kinetics for the whole reaction are obtained during the thermal decomposition of dioxetanes only, if inclusions of impurities in commercial sample pans are blocked by additional thick (magnitude of 100 ?m) and close Al2O3 protective layers. As a rule, nearly the same activation parameters are then found both for the decomposition of solvent-free dioxetanes and diluted solutions in several solvents. Mixtures of different dioxetanes in the same solvent contribute independently to the overall heat flow rate.
相似文献Viscosity plays a crucial role in the flow and heat transfer process of nanofluids. To effectively calculate and predict the changing characteristics of nanofluids viscosity, this study presents a theoretical model combining the static interface layer and dynamic Brownian motion mechanisms of spherical nanoparticles for water-based Newtonian nanofluids. The model describes the reasonable dependences of nanofluids viscosity on physical properties of nanoparticles (density, volume fraction, size) and base fluid (temperature, viscosity, density). Taking four kinds of typical water-based Newtonian nanofluids containing spherical oxide nanoparticles (Al2O3, CuO, SiO2 and TiO2) as examples, the prediction performance of different viscosity models is analyzed in detail. From the comparison studies, it is demonstrated that the new viscosity model developed in this paper can exhibit better prediction performance than many well-known theoretical models and empirical correlations. Not only do the predicted results of model agree well with the experimental data from various studies, but also the effects of different factors are reflected effectively.
相似文献