Crystallization kinetics study of melt-spun Zr66.7Ni33.3 amorphous alloy by electrical resistivity measurements

In this paper, the electronic transport properties of as-spun Zr_66.7Ni_33.3 alloys were studied in detail by a combination of electrical resistivity and absolute thermoelectric power measurements over a temperature range from 25 up to 400 °C. Moreover, the isochronal and isothermal crystallization kinetics of Zr_66.7Ni_33.3 glassy alloy has been investigated based on the electrical resistivity measurements. The comparative study of the crystallization kinetics of these binary amorphous alloys was carried out, for the first time to our knowledge, using an accurate method for electrical resistivity measurements. In the isochronal heating process, the apparent activation energy for crystallization was determined to be, respectively, 371.4 kJ mol⁻¹ and 382.2 kJ mol⁻¹, by means of Kissinger and Ozawa methods. The Johnson–Mehl–Avrami model was used to describe the isothermal transformation kinetics, and the local Avrami exponent has been determined in the range from 2.97 to 3.23 with an average value of 3.1, implying a mainly diffusion-controlled three-dimensional growth with an increasing nucleation rate. Based on an Arrhenius relationship, the local activation energy was analyzed, which yields an average value E_x = 376.2 kJ mol⁻¹.

     

Investigation of isothermal and dynamic cure kinetics of epoxy resin/nadic methyl anhydride/dicyandiamide by differential scanning calorimetry (DSC)

Isothermal and dynamic differential scanning calorimetry (DSC) was exploited to study the curing behavior of diglycidyl ether bisphenol-A epoxy resin with various combining ratios of dicyandiamide (DICY) and nadic methyl anhydride (NMA). Curves of prepared samples indicated that the enthalpy of the reaction decreased with increasing the molar ratios (NMA/DICY) up to 40% after which an exothermic peak peculiar to the effect of anhydride appeared at a higher temperature. The curing behavior examination of the samples containing the aforementioned molar ratio of NMA/DICY (= 40%) was carried out using isothermal condition at different temperatures (130–145 °C) and dynamic condition DSC at various heating rates (2.5–20 °C min⁻¹). Under the isothermal condition, by constructing a master curve, the values of activation energy (E_a) and pre-exponential factor (A) were calculated 89.3 kJ mol⁻¹ and 1.2 × 10⁺⁹ s⁻¹, respectively. The activation energy of the curing reactions in a dynamic mode was obtained 85.32 kJ mol⁻¹ and 88.02 kJ mol⁻¹ using Kissinger and Ozawa methods, respectively. Likewise, pre-exponential factors were also calculated 3.35 × 10⁺⁸ and 7.4 × 10 ⁺⁸ s⁻¹, respectively. The overall order of reaction for both conditions was found to be a value around 3.

     

Thermal analysis of dehydroxylation of Algerian kaolinite

Thermal analysis techniques remain important tools amongst the large variety of methods used for analysis of the dehydroxylation of kaolinite. In the present study, the kinetics of dehydroxylation of Algerian kaolinite, wet ball milled for 5 h followed by attrition milling for 1 h, was investigated using differential thermal analysis (DTA) and thermogravimetry (TG). Experiments were carried out between room temperature and 1350 °C at heating rates of 5, 10 and 20 °C min⁻¹. The temperature of dehydroxylation was found to be around 509 °C. The activation energy and frequency parameter evaluated through isothermal DTA treatment were 174.69 kJ mol⁻¹ and 2.68 × 10⁹ s⁻¹, respectively. The activation energies evaluated through non-isothermal DTA and TG treatments were 177.32 and 177.75 kJ mol⁻¹, respectively. Growth morphology parameters n and m were found to be almost equal to 1.5.     

Study of pyrolysis kinetic of green corn husk

In this paper, it was suggested the use of green corn husk, which is a biomass from agro-industry, as an alternative source of energy through its pyrolysis. Green corn husk characterization was done through immediate and elemental analysis of its components: cellulose, hemicelluloses, and lignin. It was also measured its higher calorific value. The pyrolysis study of green corn husk was done by the isoconversion and the Master plots method. Thermogravimetric plots were obtained at heating rates of 5, 10, 15, and 20 °C min^?1. The pyrolysis kinetics parameters were studied through the Flynn–Wall–Ozawa (FWO), Kissinger, and Friedman models. The Master plots method was used to determine the pyrolysis reaction order. The results of the reaction energy activation were found to be in the range 105.21–157.46 kJ mol^?1 by the FWO method, 150.50 kJ mol^?1 by the Kissinger method, and ranged 120.66–163.81 kJ mol^?1 by the Friedman method. The Master plots method showed a three-way-transport diffusional kinetics for the biomass de-volatilization process. The higher calorific value found for green corn husk was 16.14 MJ kg^?1. The simulation showed correlation between the experimental data and the proposed model for conversion values up to 0.8.

     

Kinetic study of crystallization of PHB in presence of hydroxy acids

Poly(3-hydroxybutyrate), PHB, has been structurally modified through reaction with hydroxy acids (HA) such as tartaric acid (TA) and malic acid (MA). The crystallization kinetic of the samples was evaluated by isoconversional method through nonlinear fitting to obtain the estimation for activation energy (E _a ) and pre-exponential (A) values. The thermal behavior of the crystallization temperature, 44.8 and 58.9 °C at 5 °C/min, and results obtained to the average activation energy, 73 ± 9 kJ mol⁻¹ and 63 ± 1 kJ mol⁻¹, to PHB/MA and PHB, respectively, are suggesting that malic acid may be deriving plasticizer units from its own PHB chain. PHB/TA show increase in the medium value of E _a, 119 ± 2 kJ mol⁻¹ and T _c = 48.2 °C (at 5 °C/min), indicating that tartaric acid is probably interacts in different way to the of PHB chain (E _a=73 ± 9 kJ mol⁻¹, T _c = 44.8 °C at 5 °C/min).     

Vapor pressure, kinetics and enthalpy of sublimation of bis(2,2,6,6-tetramethyl-3,5-heptanedionato)copper(II)

The kinetics of sublimation of bis(2,2,6,6-tetramethyl-3,5-heptanedionato)copper(II), [Cu(tmhd)₂] was studied by non-isothermal and isothermal thermogravimetric (TG) methods. The non-isothermal sublimation activation energy values determined following the procedures of Friedman, Kissinger, and Flynn–Wall methods yielded 93 ± 5, 67 ± 2, and 73 ± 4 kJ mol⁻¹, respectively and the isothermal sublimation activation energy was found to be 97 ± 3 kJ mol⁻¹ over the temperature range of 375–435 K. The dynamic TG run proved the complex to be completely volatile and the equilibrium vapor pressure (p_e)_T of the complex over the temperature range of 375–435 K determined by a TG-based transpiration technique, yielded a value of 96 ± 2 kJ mol⁻¹ for its standard enthalpy of sublimation (Δ_subH°).     

Glass transition and crystallization study of chalcogenide Se<Subscript>70</Subscript>Te<Subscript>15</Subscript>In<Subscript>15</Subscript> glass

Differential scanning calorimetry data at different heating rates (5, 10, 15 and 20 °C min⁻¹) of Se₇₀Te₁₅In₁₅ chalcogenide glass is reported and discussed. The crystallization mechanism is explained in terms of recent analyses developed for use under non-isothermal conditions. The value of Avrami exponent (n) indicates that the glassy Se₇₀Te₁₅In₁₅ alloy has three-dimensional growth. The average values of the activation energy for glass transition, E _g, and crystallization process, E _c, are (154.16 ± 4.1) kJ mol⁻¹ and (98.81 ± 18.1) kJ mol⁻¹, respectively. The ease of glass formation has also been studied. The reduced glass transition temperature (T _rg), Hruby’ parameter (K _gl) and fragility index (F _i) indicate that the prepared glass is obtained from a strong glass forming liquid.     

A variable temperature 1H NMR and DFT study of procyanidin B2 conformational interchange

Two procyanidin B2 conformers were identified in a relative abundance ratio of approximately 3:1 at 298 K by ¹H NMR experiments in acetonitrile. The conformational interchange reactions between these two conformers are 1st order in both reactions, with ?G^? for forward and reverse of 57.12?±?5.62 and 54.56?±?5.48 kJ mol^?1, respectively. The experimentally obtained standard thermodynamic energies for this reaction are ΔH⁰_rxn (3.67?±?0.22 kJ mol^?1), ΔS⁰_rxn (4.05?±?1.57 kJ mol^?1 K^?1), and ΔH⁰_rxn (2.96?±?0.33 kJ.mol^?1). Conformational search results at the DFT (PBE, PBE-D2, and B3LYP with 6-311++g**) level of theory yielded four novel conformations, named fully compact (FC), partially compact (PC), partially extended (PE), and fully extended (FE). Although the FC conformer is electronically the most stable of the four as a result of extensive intramolecular non-covalent interactions, the PC and FE conformers are thermodynamically favored in a 5:1 ratio (B3LYP), with the FC and PE conformers present in negligible amounts at equilibrium. The DFT computed standard reaction energies using the B3LYP functional for the PC_major to FE_minor conformational interchange reaction compare exceptionally well with experimental data at 298 K: ?G⁰_rxn (3.86 kJ mol^?1), ΔH⁰_rxn (5.34 kJ mol^?1), and ?S⁰_rxn (4.97 kJ mol^?1 K^?1). It was found that inclusion of solvation energies is crucial to obtain accurate thermodynamic energies. The secondary equilibria found in chromatographic separations are predicted to be highly dependent on solvent polarity and temperature. Similar conformational diversity and hierarchies should exist for all non-rigid procyanidin oligomers and the unique chromatographic behavior of these compounds may be a result of conformational interchange.

     

Thermal stability and lifetime of [AMIM]Cl-PFSA composite membranes

1-Allyl-3-methylimidazolium chloride [AMIM]Cl hybrid perfluorosulfonic acid (PFSA) composite electrolyte membrane was prepared and characterized by TG and FTIR technique. The conductivity was measured using AC impedance method. The results showed that when raised from 20 to 90 °C, the conductivity of composite membrane was increased from 4.50 × 10⁻⁶ to 1.34 × 10⁻⁵ S cm⁻¹, before and after the modification of triethylamine, the thermal stability of composite membrane was not changed, but the TEA-PFSA with [AMIM]Cl reactivity was a little difference. However, the heat resistance of composite membrane was significantly enhanced compared with that of PFSA membrane, the peak temperature of composite membrane almost disappeared in first stage, and offset to the high-temperature zone. When heated at 350 °C, the decomposition rate of PFSA, 10%[AMIM]Cl-PFSA and 10%[AMIM]Cl-TEA-PFSA membrane was 13.71, 3.67 and 1.26%, respectively. If the decomposition process follows isothermal first-order reaction and the conversion rate α is 10%, the activation energy E _α of the composite membrane is 97.4 kJ mol⁻¹. Besides, the isothermal lifetime of composite membrane was also measured.

     

Non-isothermal depolymerisation kinetics of poly(ethylene oxide)

The depolymerisation of low molecular weight poly(ethylene oxide) (PEO) under mild conditions was studied using a linear temperature ramped non-isothermal technique and the results compared with those obtained from a conventional isothermal technique. The analysis of the non-isothermal kinetic (NIK) data was performed using an original computer program incorporating an algorithm that systematically minimizes the sum of the squares of the residuals between the experimental data and the calculated theoretical kinetic profile in order to extract the kinetic parameters. The results revealed that the depolymerisation of PEO proceeds in accordance with the Ekenstam model and follows the Arrhenius equation over the temperature range of ca. 40-130 °C. The NIK analysis resulted in a two-dimensional convergence to produce a unique solution set for the kinetic parameters of E_a = 89.4 kJ mol⁻¹ and A = 9.6 × 10⁶ h⁻¹. These data are consistent with the results obtained from the isothermal experiments. It is proposed that NIK analysis is a quick and reliable means of obtaining kinetic parameters relevant to lifetime predictions in polymers whose degradation behaviour can be considered to be close to ideal.     

Optimization and mass transfer simulation of remazol brilliant blue R dye adsorption onto meranti wood based activated carbon

Remazol brilliant blue R dye (RBBR) brings toxicity to living organisms once it enters the environment. This study utilized response surface methodology (RSM) and Polymath software for optimization and mass transfer simulation purposes, respectively. RSM revealed that the optimum preparation conditions of meranti wood-based activated carbon (MWAC) were 441 W, 5.76 min, and 1.35 g/g for radiation power, radiation time, and KOH:char impregnation ratio (IR), respectively, which translated into 86.39 mg/g of RBBR uptakes and 31.94 % of MWAC’s yield. The simulation study predicted the mass transfer rate, r_m to be 112.20 to 1007.50 s^?1 and the adsorption rate, k₁ to be 3.96 to 4.34 h^?1. The developed model predicted the adsorption surface area, a_m to be 790.04 m²/g and this value is highly accurate as compared to the actual mesopores surface area of 825.58 m²/g. Mechanism analysis divulged that the interaction that occurred between RBBR molecules and MWAC’s surface were hydrogen bond (methylene and alkyne), dipole–dipole force (alkyl carbonate, terminal alkyne, and methoxy), and ion–dipole force (primary amine). The isotherm and kinetic studies found that the adsorption data obeyed the Freundlich model and pseudo-first-order (PFO) model the best, respectively. The Langmuir maximum adsorption capacity, Q_m was computed to be 327.33 mg/g. Thermodynamic parameters were calculated to be ?4.06 kJ mol^?1, 0.06 kJ mol^?1 K^?1, –22.69 kJ mol^?1, and 16.03 kJ mol^?1 for ΔH°, ΔS°, ΔG°, and E_a, respectively, which signified the adsorption process studied was exothermic, spontaneous and governed by physisorption.     

Thermodynamic Study of the Binding of Mercury Ion to Human Growth Hormone at Different Temperatures

The interaction of human growth hormone (hGH) with the divalent mercury ion was studied by isothermal titration calorimetry at two temperatures of 27 °C and 37 °C in aqueous solutions. We found that there is a set of two identical and non-interacting binding sites for Hg²⁺ ions. The intrinsic dissociation equilibrium constant and the molar enthalpy of binding are 4.2 mmol⋅L⁻¹ and −14.8 kJ⋅mol⁻¹ at 27 °C and 5.1 mmol⋅L⁻¹ and −14.2 kJ⋅mol⁻¹ at 37 °C, respectively. The results obtained indicate that the stability of the protein increases due to the binding of mercury ions using the extended solvation theory.     

Investigation of the bioenergy potential of microalgae Scenedesmus acuminatus by physicochemical characterization and kinetic analysis of pyrolysis

In this work, the bioenergy potential of green microalgae Scenedesmus acuminatus was evaluated through the psychochemical characteristics and kinetic study of pyrolysis, where the results indicate a good candidate for application in the thermochemical process due to its low moisture and ash content and high calorific value. Its thermal behavior under a heating rate of 10 °C min^?1 and inert atmosphere shows that decomposition occurs in two stages. Stage I (125–309 °C) involves the pyrolysis of carbohydrates and protein and stage II (309–501 °C) the pyrolysis of lipids. The Starink isoconversional method showed a better application for simulation curves, compared with methods of FWO and KAS. The average values of activated energy were 107.1 and 132.6 kJ mol^?1 for stages I and II, respectively, which indicates that pyrolysis occurs more easily in stage I than in stage II. The conversion rate curves show that the calculated kinetic parameters are satisfactory for the evaluation of the thermochemical systems.

     

Measurement of spherulite growth rates using tailored temperature programs

A method recently proposed for measuring spherulite growth rates (G) using temperature programs, tailored for each polymer, is reviewed. This method, compared to the conventional isothermal procedure, permits to expand the temperature range where spherulite growth rates can be measured. Examples of application of this method are reported, in particular, the spherulite growth rates of isotactic polypropylene (iPP) and poly(l-lactic acid) (PLLA) are analyzed. For iPP, growth rates were obtained from 112 to 148 °C using different cooling rates and a self-nucleation procedure. For PLLA, measurements in both isothermal and non-isothermal conditions allowed to overcome the difficulties due to the very high nucleation density that prevent determination of growth rates at low crystallization temperatures. For this polymer the entire curve of G vs. T was obtained.     

A thermodynamic study on the interaction of nickel ion with myelin basic protein by isothermal titration calorimetry

The interaction of myelin basic protein (MBP) from the bovine central nervous system with divalent nickel ion was studied by isothermal titration calorimetry at 37 and 47 °C in Tris buffer solution at pH = 7. The new solvation model was used to reproduce the heats of MBP + Ni²⁺ interaction over the whole Ni²⁺ concentrations. It was found that MBP has three identical and independent binding sites for Ni²⁺ ions. The intrinsic dissociation equilibrium constant and the molar enthalpy of binding are 89.953 μM, −14.403 kJ mol⁻¹ and 106.978 μM, −14.026 kJ mol⁻¹ at 37 and 47 °C, respectively. The binding parameters recovered from the new solvation model were correlated to the structural changes of MBP due to its interaction with nickel ion interaction. It was found that in the low and high concentrations of the nickel ions, the MBP structure was destabilized.     

Preparation and characterization of nitrogen-rich bis-1-methylimidazole1H,1′H-5,5′-bistetrazole-1,1′-diolate energetic salt

A new nitrogen-rich energetic salt of bis-1-methylimidazole 1H,1′H-5,5′-bistetrazole-1,1′-diolate salt, (1-M)₂BTO, was synthesized and characterized (FT-IR, ¹H NMR, ¹³C NMR, elemental analysis, and X-ray single-crystal diffraction). Results indicated that (1-M)₂BTO crystallizes in the triclinic space group P-1. The thermal decomposition behavior of (1-M)₂BTO was determined by differential scanning calorimetry (DSC) and thermogravimetric tandem infrared spectroscopy. The decomposition peak temperature of (1-M)₂BTO was 530 K, which suggested that the salt is strong heat resistance. The apparent activation energies were 130.56 kJ mol^?1 (Kissinger’s method) and 132.50 kJ mol^?1 (Ozawa’s method), respectively. The enthalpy of formation for the salt was calculated as 917.3 kJ mol^?1. The detonation velocity and detonation pressure of (1-M)₂BTO were 7448 m s^?1 and 20.7 GPa, respectively, using the Kamlet-Jacobs equation. Furthermore, the sensitivity test results showed that its impact sensitivity is greater than 50 J and friction sensitivity is 180 N, indicating that it has a lower sensitivity.

     

Mechanical properties and crystallization behavior of polypropylene with cyclodextrin derivative as ��-nucleating agent

It was found that lanthanum complex of cyclodextrin derivative (??-CD?CMAH?CLa) was a highly active ??-nucleating agent for isotactic polypropylene (iPP) in this study. The influence of the nucleating agent on mechanical properties and isothermal and nonisothermal crystallization behavior of iPP has been investigated. Results showed that ??-CD?CMAH?CLa was efficient in inducing the crystallization of iPP into ??-modification (??-iPP), with K _?? value of 0.84, while the content of nucleating agent was 0.8?wt.%. ??-iPP could form extensively in the isothermal crystallization temperature range from 110?°C to 140?°C, and the highest amount of ??-crystal content was formed at 130?°C. Besides, it can be known that the addition of ??-CD?CMAH?CLa can obviously facilitate the overall crystallization process of iPP. Under nonisothermal condition, ??-iPP formed at the suitable cooling rates, ranging from 5?°C to 10?°C/min. Furthermore, the nucleation mechanism of ??-CD?CMAH?CLa for iPP was correlated to the special configuration of ??-CD?CMAH?CLa.     

Kinetics of the thermal dehydration of trans-fluoroaquobis(ethylenediamine)chromium(III) tetracyanometallate(II) [metal(II) = Ni(II), Pd(II) and Pt(II)]

The solid phase thermal deaquation—anation of trans-[CrF(H₂O)(en)₂][M(CN)₄] (M = Ni, Pd, Pt; en = ethylenediamine) has been investigated by means of non-isothermal DSC and isothermal and non-isothermal TG measurements. The physical model for these reactions (nucleation, growth, diffusion or intermediates) has been found by comparison of the isothermal and non-isothermal TG data for all the principal g(α) expressions (0.2?α?0.8) and by the shape of the isothermal curves. The values found for activation energy are low (～ 130 kJ mol^?1 for the Ni compound, ～ 140 kJ mol^?1 for the Pd compound, and ～ 100 kJ mol^?1 for the Pt compound). These data permit the assignment of the deaquation—anation mechanism of the S_N1 type involving a square-base pyramid activated complex and elimination of water as Frenkel defects.     

Reversible unfolding of poplar iso-plastocyanins

We attempted to determine the experimental conditions under which poplar plastocyanin iso-forms PCa and PCb undergo reversible thermal unfolding studied by differential scanning calorimetry (DSC). Our results indicate that an exothermic unfolding process exists always in the presence of molecular oxygen. Reversible unfolding and almost perfect two-state transitions were exhibited in the presence of TCEP under anaerobic conditions. This suggests that the second endothermic peak is due to copper-site disulfide dimmers formed during thermal denaturation. The conformational thermal stability of reduced PCb (ΔG (25 °C) = 33.9 kJ mol⁻¹) has proven to be higher than that of reduced PCa (ΔG(25 °C) = 22.9 kJ mol⁻¹).     

Thermal behavior of isotactic polypropylene in different content of β-nucleating agent

The effects of non-isothermal and isothermal crystallization on the formation of α- and β-phase in isotactic polypropylene (iPP) with different content of β-nucleating agent are investigated by differential scanning calorimetry (DSC). On non-isothermal crystallization, the content of β-phase and regularity of its crystals are depended on both cooling rate and the content of β-nucleating agent. The faster cooling rate is, the lower of melting peak temperature (T_mp) and crystallization peak temperature (T_cp) of α- and β-phase are. The enthalpy of fusion (∆H) of β-phase increases with cooling rate in a certain range for the sample with 0.1 wt% β-nucleating agent (G₁) and decreases for that with 0.3 wt% β-nucleating agent (G₃). On isothermal crystallization, the enthalpy of fusion of β-phase in G₁ is higher than in G₃ which is related to the efficiency of nucleation in different concentration of nucleating center in two samples.