Fast miniaturised sample preparation for the screening and comprehensive two-dimensional gas chromatographic determination of polychlorinated biphenyls in sludge

Polychlorinated biphenyls (PCBs) in sludge are usually extracted by a technique such as Soxhlet with subsequent fractionation prior to long GC runs using GC-ECD or GC-HRMS. In this study, the extraction of selected chlorinated biphenyls (CBs) from a spiked sludge sample by three rapid techniques, i.e. ultrasonic (USE), pressurised-liquid (PLE), and microwave-assisted (MAE) extraction using a domestic microwave, was studied, with subsequent direct GC-ECD, GC-MS, or GC x GC-microECD analysis of the extracts. The main goal was to select an appropriate, and miniaturised, extraction method after only a brief optimisation and demonstrate the power of GC x GC analysis of dirty extracts. For PLE similar CB recoveries were found when extracting with either n-hexane or n-hexane/acetone (1/1). For USE and MAE, n-hexane/acetone (1/1) was the preferred extraction solvent. USE gave the best recoveries (80-95%; except 130% for CB 105). The only clean-up needed prior to GC-MS or GC x GC-gECD analysis was the removal of sulphur-containing compounds. GC-ECD was not suitable for these dirty extracts. The lowest LODs for the CBs (20 fg or 0.1 ng/g sludge) were found when combining USE and GC x GC-microECD, because of the powerful extraction, high separation power and excellent detectability provided by this technique.     

Comparing the effect of sub-critical water extraction with conventional extraction methods on the chemical composition of Lavandula stoechas

The volatile extract composition of Lavandula stoechas flowers obtained by hydrodistillation (HD), subcrtical water extraction (SbCWE) and organic solvent extraction under ultrasonic irradiation (USE) were estimated by gas chromatography-mass spectrometry (GC-MS). One hundred and twenty four components were detected in SbCWE extracts while 94 and 65 signals were gained from HD and USE extracts, respectively. Most of the constituents were identified. The major compounds in all three extracts were fenchon, camphor, myrtenyl acetate, myrtenol and 1,8-cineol, but they differ in quantitatively. The total monoterpene hydrocarbons are higher in HD and USE extracts than those of SbCWE extract. However, SbCWE extract had higher concentration of light oxygenated compounds which contributes to the fragrance of the oil in a major extension. Heavy-oxygenated compounds was also in higher abundance in SbCWE extract (9.90%) than those of HD and USE extracts (3.19 and 4.78%, respectively). Effect of temperature on the extraction yield of SbCWE was investigated and while oil yield was increasing with an increase in temperature, a decrease in the extraction ability of sub-critical water toward the more polar compounds such as, 1,8-cineol, camphor and fenchon, was observed. Kinetic studies shown that SbCWE is clearly quicker than conventional alternatives. Most of components of volatile compounds were extracted at 15min.     

Screening of natural organic volatiles from Prunus mahaleb L. honey: coumarin and vomifoliol as nonspecific biomarkers

Headspace solid-phase microextraction (HS-SPME; PDMS/DVB fibre) and ultrasonic solvent extraction (USE; solvent A: pentane and diethyl ether (1:2 v/v), solvent B: dichloromethane) followed by gas chromatography and mass spectrometry (GC, GC-MS) were used for the analysis of Prunus mahaleb L. honey samples. Screening was focused toward chemical composition of natural organic volatiles to determine if it is useful as a method of determining honey-sourcing. A total of 34 compounds were identified in the headspace and 49 in the extracts that included terpenes, norisoprenoids and benzene derivatives, followed by minor percentages of aliphatic compounds and furan derivatives. High vomifoliol percentages (10.7%-24.2%) in both extracts (dominant in solvent B) and coumarin (0.3%-2.4%) from the extracts (more abundant in solvent A) and headspace (0.9%-1.8%) were considered characteristic for P. mahaleb honey and highlighted as potential nonspecific biomarkers of the honey's botanical origin. In addition, comparison with P. mahaleb flowers, leaves, bark and wood volatiles from our previous research revealed common compounds among norisoprenoids and benzene derivatives.     

Determination of vitexin and isovitexin in pigeonpea using ultrasonic extraction followed by LC-MS

A method based on ultrasonic extraction (USE) followed by LC-MS is presented for the determination of vitexin and isovitexin in pigeonpea extracts in this study. The influential parameters of the USE procedure were optimized, and the optimal conditions were as follows: extraction solvent, 60% ethanol solution; liquid/solid ratio 10:1 (mL/g), extraction power, 250 W; temperature, 40-50 degrees C; and three extraction cycles, each cycle 15 min. Validation of the USE method was performed in terms of repeatability and reproducibility. RSDs for extraction yields were lower than 5.85 and 8.09%, respectively. The LOD and LOQ of chromatographic determination were 0.96 and 3.2 ng/mL for vitexin and 0.84 and 2.8 ng/mL for isovitexin. The method was also successfully applied for the determination of vitexin and isovitexin in stems, leaves, and root extracts of pigeonpea. From all these results, we may conclude that the developed method is appropriate for the quality control of pigeonpea and other plant extract products developed from pigeonpea.     

A Comparison of Three Methods of Extraction for the Determination of Polyphenols and Organic Acids in Tobacco by UPLC–MS–MS

Matrix solid phase dispersion (MSPD), ultrasonic extraction followed by a solid phase extraction (USE–SPE) and reflux extraction (REFLUX) were studied for the analysis of polyphenols and organic acids in tobacco. The analysis was by ultra-high performance liquid chromatography tandem mass spectrometry (UPLC–MS–MS). The multi-mode support sorbent Zirconia/AA12S50 in MSPD is more suitable for the extraction of tobacco polyphenols than conventional silica or C18 silica. Although the matrix effect of USE–SPE is slightly stronger than MSPD and REFLUX for most target compounds, it gave higher extraction capacity, recoveries and sensitivity.     

Simultaneous determination of trace migration of phthalate esters in honey and royal jelly by GC–MS

A simple, rapid, and reliable liquid–liquid extraction coupled to GC–MS method was developed and validated for the quantification of 22 phthalate esters (PAEs) in honey and royal jelly. Instrument parameters for GC–MS were tested to obtain the satisfactory separation between 22 PAEs with high sensitivity. The extraction procedure was optimized in order to achieve the best recovery. The following criteria were used to validate the developed method: linearity, LOD, lower LOQ, precision, accuracy, matrix effect and carry‐over. Correlation coefficients were >0.999 by applying the linear regression model based on the least‐squares method with a weighting factor (1/x). The intra‐ and interday precision were within 12.7% in terms of RSD, and the accuracy was within ?11.8% in terms of relative error. The mean extraction recoveries ranged between 80.1 and 110.9% for honey and royal jelly. No significant matrix effect and carry‐over for PAEs were observed for the analysis of honey and royal jelly samples. A total of 20 real samples were analyzed for a mini‐survey using the developed method. Seven PAEs in honey samples and five PAEs in royal jelly samples were found, indicating potential contamination with several PAEs.     

Determination of PAHs in dust from Shanghai by optimized SFE and GC/MS

EPA 16 priority polycyclic aromatic hydrocarbons (PAHs) were extracted from dust by supercritical fluid extraction (SFE). Parameters (pressure, temperature and time) affecting the collection efficiencies of PAHs were assessed according to the extraction efficiency, and 30 MPa, 80 degrees C and 30 min dynamic extraction time were confirmed to be the best and simplest conditions of SFE to extract 16 priority PAHs from dust. The characterization of the extracts was carried out by gas chromatography with mass detector in selective ion mode (GC/MS/SIM). Ultrasonic extraction (USE) was used as a comparison with SFE. The results showed that the SFE method has a better efficiency than USE for the extraction of PAHs in dust. With the optimized conditions of SFE, the distribution of PAHs in dust samples in urban areas of Shanghai from Mar 10, 2005 to May 28, 2005 was investigated. The results demonstrated that traffic emission, especially from gasoline engines, was the main source of PAHs in dust of Shanghai.     

Comparison of pressurised fluid and ultrasonic extraction methods for analysis of plant antioxidants and their antioxidant capacity

The analytical method based on the high-performance liquid chromatography coupled with UV detection (HPLC/UV) for determination of selected antioxidants (i.e., esculetin, scopoletin, 7-hydroxycoumarine, rutin, xanthotoxin, 5-methoxypsoralen and quercetin) in plant material was developed. Pressurised fluid extraction (PFE) and ultrasonic extraction (USE) methods for the isolation of these compounds from ten real plant samples were used. Both extraction methods were optimised and compared to each other. For the proposed HPLC/UV method the LOQ values (limit of quantification) in the range from 22.7 (xanthotoxin) to 97.2 ng mL⁻¹ (rutin) were obtained. For all extracts the antioxidant capacity based on the reduction of free 2,2-diphenyl-1-picrylhydrazyl radical (DPPH) was also determined. Results ranged from 82.04 to 94.43% of DPPH radical inhibition for PFE method and from 76.01 to 89.94% in the case of USE method.     

Comparison of various extraction techniques for isolation and determination of isoflavonoids in plants

In the present paper, the following extraction techniques have been used for extracting isoflavonoids from the species Matricaria recutita, Rosmarinus officinalis, Foeniculum vulgare, and Agrimonia eupatoria L.: supercritical fluid extraction (SFE), pressurized fluid extraction, matrix solid phase dispersion, ultrasonic extraction in an ultrasonic bath (USE) and by means of an ultrasonic homogeniser (HOM), extraction by means of Soxhlet apparatus (SOX), and solid phase extraction. Experimental optimization of all techniques has been carried out using a soybean flour. Subsequent analyses of the extracts were carried out by liquid chromatography with UV detection. The maximum yields of daidzein and genistein were obtained by extraction with the SOX, USE, and HOM techniques. The maximum yields of apigenin and biochanin A from herb samples were obtained by SFE.     

Development of an ultrasound‐assisted emulsification microextraction method for the determination of chlorpyrifos and organochlorine pesticide residues in honey samples using gas chromatography with mass spectrometry

A simple, rapid, and efficient ultrasound‐assisted emulsification microextraction method followed by gas chromatography mass spectrometry in selected ion monitoring mode was developed for the determination of organochlorine pesticides in honey samples. The type and volume of organic extraction solvent, pH, effect of added salt content, and centrifuging time and speed were investigated. Under the optimum extraction conditions, 30 μL of 1, 2‐dibromoethane (extraction solvent) was immersed into an ultrasonic bath for 1 min at 40°C. The limits of detection and quantification for all target pesticides were 0.003–0.06 and 0.01–0.2 ng/g_, respectively. The extraction recovery was 91–100% and the enrichment factors were 168–192. The relative standard deviation for the method was <6% for intraday (n = 6) and <8% for interday precision (n = 4). The proposed method was successfully applied for the analysis of organochlorine pesticides in honey samples.     

Effervescence‐assisted dispersive solid‐phase extraction using ionic‐liquid‐modified magnetic β‐cyclodextrin/attapulgite coupled with high‐performance liquid chromatography for fungicide detection in honey and juice

In this study, a simple effervescence‐assisted dispersive solid‐phase extraction method was developed to detect fungicides in honey and juice. Most significantly, an innovative ionic‐liquid‐modified magnetic β‐cyclodextrin/attapulgite sorbent was used because its large specific surface area enhanced the extraction capacity and also led to facile separation. A one‐factor‐at‐a‐time approach and orthogonal design were employed to optimize the experimental parameters. Under the optimized conditions, the entire extraction procedure was completed within 3 min. In addition, the calibration curves exhibited good linearity, and high enrichment factors were achieved for pure water and honey samples. For the honey samples, the extraction efficiencies for the target fungicides ranged from 77.0 to 94.3% with relative standard deviations of 2.3–5.44%. The detection and quantitation limits were in the ranges of 0.07–0.38 and 0.23–1.27 μg/L, respectively. Finally, the developed technique was successfully applied to real samples, and satisfactory results were achieved. This analytical technique is cost‐effective, environmentally friendly, and time‐saving.     

Dispersive micro‐solid‐phase extraction of benzoylurea insecticides in honey samples with a β‐cyclodextrin‐modified attapulgite composite as sorbent

A β‐cyclodextrin‐modified attapulgite composite was prepared and used as a dispersive micro‐solid‐phase extraction sorbent for the determination of benzoylurea insecticides in honey samples. Parameters that may influence the extraction efficiency, such as the type and volume of the eluent, the amount of the sorbent, the extraction time and the ionic strength were investigated and optimized using batch and column procedures. Under optimized conditions, good linearity was obtained for all of the tested compounds, with R² values of at least 0.9834. The limits of detection were determined in the range of 0.2–1.0 μg/L. The recoveries of the four benzoylurea insecticides in vitex honey and acacia honey increased from 15.2 to 81.4% and from 14.2 to 82.0%, respectively. Although the β‐cyclodextrin‐modified attapulgite composite did not show a brilliant adsorption capacity for the selected benzoylurea insecticides, it exhibited a higher adsorption capacity toward relatively hydrophobic compounds, such as chlorfluazuron and hexaflumuron (recoveries in vitex honey samples ranged from 70.0 to 81.4% with a precision of 1.0–3.7%). It seemed that the logP_ow of the benzoylurea insecticides is related to their recoveries. The results confirmed the possibility of using cyclodextrin‐modified palygorskite in the determination of relatively hydrophobic trace pharmaceutical residues.     

Core-shell magnetic porous organic polymer for magnetic solid-phase extraction of fluoroquinolone antibiotics in honey samples followed by high-performance liquid chromatography with fluorescence detection

By monomer-mediated in-situ growth synthesis strategy, with hydroquinone and 1,3,5-tris(4-aminophenyl)benzene as monomers, a core-shell magnetic porous organic polymer was synthesized through a simple azo reaction. Based on this, a magnetic solid-phase extraction–high-performance liquid chromatography–fluorescence detection method was proposed for the analysis of fluoroquinolones in a honey sample. With ofloxacin, ciprofloxacin, enrofloxacin, lomefloxacin, and difloxacin as target analytes, factors affecting the extraction efficiency had been optimized. The LODs were 1.5–5.4 ng/L (corresponding to 0.23–0.81 μg/kg in honey). The linear range was 0.005–20 μg/L for difloxacin, 0.01–20 μg/L for ofloxacin, ciprofloxacin and lomefloxacin, and 0.02–20 μg/L for enrofloxacin. The enrichment factor was 84.4–91.7-fold with a high extraction efficiency of 84.4–91.7%. The method was assessed by the analysis of target fluoroquinolones in honey samples, and the recoveries for the spiked samples were 79.3–95.8%. The results indicated that the established magnetic solid-phase extraction–high-performance liquid chromatography–fluorescence detection method is efficient for the analysis of trace fluoroquinolones in honey.     

Influence of extrahent on antioxidant capacity of Aesculus hippocastanum seeds

In this study, the optimisation of horse chestnut seed extraction was performed to determine the best extraction solvent in the recovery of pharmacologically active escin from raw material. All extracts were obtained by accelerated solvent extraction and were analysed for their antioxidant potential (DPPH test), phenolic content (Folin–Ciocalteu (FC) assay) and escin content (ESI-TOF-MS extracts profiling). Methanol was found to recover the highest amount of escin from the plant matrix as well as to produce the most active antiradical solutions rich in polyphenols. Radical scavenging properties of methanol extracts were calculated as 2 GAE in DPPH test and 23 GAE (mg/g) in FC assay. Quantitative analysis of extracts performed by ESI-TOF-MS measurements in ion-positive mode confirmed the presence of four major escin isomers in the extracts and showed that the high antioxidant potential of methanolic extracts went hand in hand with the highest content of escin (8.92%).     

Determination of aminoglycoside residues in kidney and honey samples by hydrophilic interaction chromatography‐tandem mass spectrometry

Two methods based on liquid chromatography–tandem mass spectrometry were developed for the determination of ten aminoglycosides (streptomycin, dihydrostreptomycin, spectinomycin, apramycin, paromomycin, kanamycin A, gentamycin C1, gentamycin C2/C2a, gentamycin C1a, and neomycin B) in kidney samples from food‐producing animals and in honey samples. The methods involved extraction with an aqueous solution (for the kidney samples) or sample dissolution in water (for the honey samples), solid‐phase extraction with a weak cation exchange cartridge and injection of the eluate into a liquid chromatography–tandem mass spectrometry system. A zwitterionic hydrophilic interaction chromatography column was used for separation of aminoglycosides and a triple quadrupole mass analyzer was used for detection. The methods were validated according to Decision 2002/657/EC. The limits of quantitation ranged from 2 to 125 μg/kg in honey and 25 to 264 μg/kg in the kidney samples. Interday precision (RSD%) ranged from 6 to 26% in honey and 2 to 21% in kidney. Trueness, expressed as the percentage of error, ranged from 7 to 20% in honey and 1 to 11% in kidney.     

Sol–gel polydimethylsiloxane/poly(vinylalcohol)‐coated stir bar sorptive extraction of organophosphorus pesticides in honey and their determination by large volume injection GC

A PDMS/poly(vinylalcohol) (PDMS/PVA) film prepared through a sol–gel process was coated on stir bars for sorptive extraction, followed by liquid desorption and large volume injection–GC–flame photometric detector (LVI–GC–FPD) for the determination of five organophosphorus pesticides (OPPs) (phorate, fenitrothion, malathion, parathion, and quinalphos) in honey. The preparation reproducibility of PDMS/PVA‐coated stir bar ranged from 4.3 to 13.4% (n = 4) in one batch, and from 6.0 to 12.6% (n = 4) in batch to batch. And one prepared stir bar can be used for more than 50 times without apparent coating loss. The significant parameters affecting stir bar sorptive extraction (SBSE) were investigated and optimized. The LODs for five OPPs ranged from 0.013 (parathion) to 0.081 μg/L (phorate) with the RSDs ranging from 5.3 to 14.2% (c = 1 μg/L, n = 6). The proposed method was successfully applied to the analysis of five OPPs in honey.     

Sensitive monitoring of penicillin antibiotics in milk and honey treated by stir bar sorptive extraction based on monolith and LC‐electrospray MS detection

In the present study, a convenient and sensitive method for determination of six penicillin antibiotics (amoxicillin, ampicillin, penicillin G, oxacillin, cloxacillin, and dicloxacillin) in milk and honey samples was developed. Milk and honey samples were diluted with water, then directly treated by stir bar sorptive extraction based on poly (vinylimidazole‐divinylbenzene) monolithic material as coating. The analytes were analyzed by LC/ESI‐ MS/MS. Several extraction parameters including extraction and desorption time, pH value, and ionic strength in sample matrix were investigated in detail. Under the optimized extraction conditions, the calculated detection limits for the target compounds were as low as 0.23–2.66 ng/kg in milk and 0.18–1.42 ng/kg in honey, respectively. Good linearity was obtained for analytes with the correlation coefficients (R²) above 0.997. Excellent method reproducibility was achieved in terms of intraday and interday precisions, indicated by the RSDs of <5.0 and <10.0%, respectively. Finally, the proposed method was successfully applied to the determination of penicillin antibiotics residues in different milk and honey samples.     

Development of organic solvents‐free mode of solidification of floating organic droplet–based dispersive liquid–liquid microextraction for the extraction of polycyclic aromatic hydrocarbons from honey samples before their determination by gas chromatography–mass spectrometry

In this study, a green mode of solidification of floating organic droplet – based dispersive liquid–liquid microextraction has been developed for the extraction of 16 polycyclic aromatic hydrocarbons from honey samples before their determination by gas chromatography–mass spectrometry. In this method, an appropriate volume of menthol:decanoic acid deep eutectic solvent (as an extraction solvent) is added on a sugar cube (as a disperser agent). In the following, the cube is released into the diluted honey sample placed in a tube. After manual shaking a cloudy state is obtained as a result of dispersing the extraction solvent droplets throughout the sample solution and the analytes are extracted into them. After placing the tube in an ice bath, the droplet of the extractant is solidified on the top of the solution. This drop is taken and after dissolving in acetonitrile, an aliquot of the solution is injected into the separation system. Under optimum conditions, the suggested approach had high extraction recoveries (76–93%) and enrichment factors (380–465), low limits of detection (14–52 ng/kg) and quantification (47–173 ng/kg), and satisfactory repeatability (relative standard deviation ≤ 9%).     

Simultaneous determination of fluoroquinolone and tetracycline antibacterials in sewage sludge using ultrasonic-assisted extraction and HPLC-MS/MS

A reliable method was proposed for the simultaneous determination of five fluoroquinolones (FQs) and two tetracyclines (TCs) in sewage sludge using ultrasonic-assisted extraction (USE) followed by SPE cleanup and high-performance liquid chromatography-mass spectrometry (HPLC-MS)/MS analysis with electrospray ionisation (ESI) in a positive mode. The USE conditions (e.g. extraction solvent, pH, and extraction cycles) and high-performance liquid chromatography-tandem mass spectrometry (HPLC-MS/MS) parameters were optimised. Quantification was performed by internal standard calibration in multiple reaction monitoring mode. Recoveries of the antibacterials ranged from 41 to 123%, with relative standard deviations within 17%. The sample-based limits of quantification were 10–63?ng?g^?1 dry weight (dw) for FQs (ciprofloxacin, enrofloxacin, lomefloxacin, norfloxacin, and ofloxacin) and 250–500?ng?g^?1 dw for TCs (tetracycline and oxytetracycline). The method was applied to determine the antibacterials in sewage sludge and sediment samples were collected from the Pearl River Delta, China. Ciprofloxacin, norfloxacin, and ofloxacin were frequently detected, ranging from 1052 to 17740?ng?g^?1 dw in dewatered sludge samples, 585–3545?ng?g^?1 dw in untreated solids, and 98–258?ng?g^?1 dw in an urban stream sediment sample, respectively. Lomefloxacin and enrofloxacin were also occasionally detected.     

Ultrasonic/Soxhlet/supercritical fluid extraction kinetics of pyrethrins from flowers and allethrin from paper strips

Three different extraction methods (ultrasonic extraction (USE), Soxhlet extraction (SOX) and supercritical fluid extraction (SFE)) were compared for the extraction of pyrethrins from chrysanthemic flowers and commercial insecticide powder. Allethrin was extracted from paper strips. All extracts and the kinetics were analyzed by supercritical fluid chromatography and flame ionization detector. Received: 18 January 1999 / Revised: 29 June 1999 / /Accepted: 30 June 1999