氢化物发生-原子荧光光谱法测定绞股蓝中痕量铋

研究了氢化物发生-原子荧光光谱法测定中草药绞股蓝中痕量铋的适宜条件,试验了不同的消解方式、酸介质和还原剂用量对测定铋的影响。在最佳测定条件下,铋的线性范围为0.1~200μg.L-1,检出限为0.095μg.L-1。样品分析结果的相对标准偏差为4.28%(n=6),加标平均回收率为99.5%。     

铋膜电极溶出伏安法测定食品中痕量重金属

以铋膜电极为工作电极,采用微分脉冲阳极溶出伏安法直接测定食品样品中痕量铅、镉和锌。在富集电位-1.4V,富集时间180s,铋膜质量浓度150μg·L-1的条件下,铋膜电极对铅、镉和锌的氧化溶出具有良好的电化学响应。铅(Ⅱ)、镉(Ⅱ)和锌(Ⅱ)的质量浓度在5.0~40μg·L-1的范围内与其阳极溶出峰电流呈线性关系,铅(Ⅱ)、镉(Ⅱ)和锌(Ⅱ)的检出限(3S/N)分别为0.80,0.65,0.58μg·L-1。对25μg·L-1铅(Ⅱ)、镉(Ⅱ)和锌(Ⅱ)溶液用铋膜电极连续测定15次,相对标准偏差分别为6.2%,5.1%,7.1%。方法应用于食品中痕量重金属的测定,测定结果与石墨炉原子吸收光谱法的测定值相符。     

硅藻土吸附在线柱富集-火焰原子吸收光谱法测定环境水样中痕量铜

提出了硅藻土吸附在线柱富集-火焰原子吸收光谱法测定环境水样中痕量铜的方法。利用硅藻土对环境水样中痕量铜在线预富集,浓集因子达到27.6,使火焰原子吸收光谱法的检测能力达到测定环境水样中痕量铜的要求。方法检出限为0.32μg.L-1,RSD(20μg.L-1)为3.52%,加标回收率为97.0%~105.0%。     

阻抑动力学光度法测定环境水样中苯胺

基于在乙酸-乙酸钠缓冲溶液介质中,痕量苯胺能灵敏地阻抑过氧化氢氧化溴甲酚绿褪色。研究了该阻抑褪色反应的最佳条件及动力学参数,建立了测定痕量苯胺的方法。该法的线性范围为0~45.0μg.L-1,检出限为4.30μg.L-1。用于环境水样中痕量苯胺的测定,结果的RSD值在2.35%~3.78%之间,回收率在95.8%~103.6%。     

ICP-MS法测定镍基单晶高温合金DD416中的镓、锡、锑、铅、铋

建立电感耦合等离子体质谱法测定镍基单晶高温合金DD416中镓、锡、锑、铅、铋元素的含量。以盐酸–硝酸(体积比3∶1)混合酸为消解剂,利用微波消解仪消解样品,以Rh(10μg/L)为内标元素。镓的线性范围为0～50μg/g,锡、锑、铅的线性范围为0～20μg/g,铋的线性范围为0～2μg/g,线性相关系数均大于0.999,检出限分别为0.01,0.2,0.1,0.07,0.006μg/g。用该方法对标准物质进行测定,测定结果与标准值之间的相对误差在7.7%～22.7%范围内。样品加标回收率为98.2%～108.0%,测定结果的相对标准偏差为0.1%～1.5%(n=5)。该方法可以快速、准确地对镍基单晶高温合金DD416中镓、锡、锑、铅、铋元素进行同时测定。     

停流-抑制动力学荧光法测定痕量苯酚

用停流技术研究了在H2SO4介质中,苯酚抑制BrO-3氧化丁基罗丹明B荧光猝灭反应,并探讨了反应机理。基于苯酚对该反应诱导期的影响作用,建立了停流-抑制动力学荧光法测定痕量苯酚的新方法。方法的检出限为1.4×10-8g.L-1,线性范围为0.4~15.0μg.L-1,11次测定7.0μg.L-1苯酚的相对标准偏差为2.1%。本法灵敏、简便,用于测定制药废水和番茄酱样品中痕量苯酚,结果满意。     

动力学催化光度法测定痕量亚硝酸根

基于硫酸介质中亚硝酸根催化溴酸钾氧化间甲酚紫的褪色反应,建立了测定痕量亚硝酸根的新方法,并探讨了动力学条件,测定了反应的表观速率常数(k′=1.03×10-4s-1)和表观活化能(E′a=10.25kJ.mol-1)。方法的测定范围为8.0~150μg.L-1,检出限为0.9μg.L-1。方法已用于水样中亚硝酸根的测定。     

流动注射荧光法测定食品和饮料中的甲醛

基于在醋酸铵缓冲溶液中,甲醛与5,5-二甲基-1,3-环己二酮反应生成荧光物质,建立了流动注射荧光法测定食品及饮料中痕量甲醛的方法.在最佳实验条件下,荧光强度与甲醛浓度在5μg.L-1~3 mg.L-1范围内呈良好的线性关系,检出限为1.28μg.L-1.该方法简单、快速.     

巯基葡聚糖凝胶分离富集动力学光度法测定痕量锡

基于稀硫酸介质中,痕量锡(Ⅳ)催化溴酸钾氧化偶氮氯膦Ⅲ(CPAⅢ)的褪色反应,建立了测定痕量锡(Ⅳ)的催化动力学光度法。方法检出限为0.25μg.L-1,线性范围为0.0~8.0μg.L-1。结合巯基葡聚糖凝胶(MDG)分离富集,用于测定环境水样、人发及岩石样品中痕量锡(Ⅳ),结果的RSD值均在9.0%以内,回收率在96.0%~103.0%之间。分析了3种岩石标准物质,所得结果与证书值相符。     

氢化物发生-原子荧光法测定高温合金中痕量铋的测量不确定度评定

介绍氢化物发生–原子荧光光谱法(HG–AFS)测定高温合金中痕量铋(Bi)的不确定度评定方法,建立了数学模型,分析了测量过程中不确定度的来源,并对不确定度分量进行了量化。当高温合金中铋含量为0.00016%时,扩展不确定度为0.00002%(k=2)。     

Spectrophotometric determination of bismuth with semi-xylenol orange and its application in metal analysis

Semi-Xylenol Orange forms a 2 : 1 chelate with bismuth(III), which has a logarithmic value of 3.08 for its conditional formation constant and a molar absorptivity of 4.2 x 10(4) l.mole(-1).cm(-1). Beer's law is obeyed at 540 nm over the range 10-30 mug of Bi(III), with a standard deviation of 1.1 mug (n = 18). Lactic acid is used as an auxiliary complexing agent to prevent olation and oxolation. Interference from up to 1.3 mg of copper can be eliminated by the combined use of masking Cu(II) with thiourea, ascorbic acid and thiosemicarbazide and "post-masking" Bi(III) with sodium chloride. The proposed method has been successfully applied to the direct determination of 0.002% of Bi in lead metal, with a coefficient of variation varying from 3.7 to 6.9%.     

Simultaneous spectrophotometric determination of Bi(III) and Sb(III) based on their complexes with iodide in acidic media using the H-point standard addition method and first-derivative spectrophotometry.

The H-point standard addition method (HPSAM) was applied to the simultaneous determination of Bi(III) and Sb(III). This method is based on the difference in the absorbance of complexes of Bi(III) and Sb(III) with iodide in acidic media in different wavelength pairs. The results showed that Bi(III) and Sb(III) can be determined simultaneously with concentration ratios of 15:1 to 1:20. First-derivative spectrophotometry was also used for the simultaneous determination of Bi(III) and Sb(III) based on their complexes with iodide. The proposed methods were successfully applied to the simultaneous determination of Bi(III) and Sb(III) in synthetic samples.     

Equilibrium, 1H and 13C NMR spectroscopy,and X-ray diffraction studies on the complexes Bi(DOTA)- and Bi(DO3A-Bu)

Several Bi(III) complexes are used in medicine as drugs. Bi(DO3A-Bu) has recently been proposed as a nonionic contrast agent in X-ray imaging (H(3)DO3A-Bu = 10-[2,3-dihydroxy-(1-hydroxymethyl)propyl]-1,4,7,10-tetraazacyclododecane-1,4,7,-triacetic acid). The solution equilibria and NMR structure and dynamics of Bi(DO3A-Bu) and of the similar Bi(DOTA)(-) have been investigated (H(4)DOTA = 1,4,7,10-tetraazacyclododecane-1,4,7,10-tetraacetic acid). The stability constants were determined with the study of the competition equilibria between Br(-) ions and the ligands DOTA or DO3A-Bu for the Bi(III) by spectrophotometry. The stability constants, obtained for Bi(DOTA)(-) and Bi(DO3A-Bu), are very high, log K = 30.3 and 26.8, respectively. Potentiometric titrations indicated the dissociation of one of the protons among the three alcoholic OH groups in Bi(DO3A-Bu). The dissociation constant is log K = 7.53 (0.09) indicating that at physiological pH about 50% of the species possess -1 charge. It was shown by (1)H and (13)C NMR spectroscopy that the OH group attached to the middle carbon atom of the "butriol" side chain is coordinated to the Bi(III) and starts to deprotonate at pH > 5.5. The crystal structure of NaBi(DOTA).H(2)O shows an octacoordinated arrangement of the donor atoms around the Bi(III), with no water in the inner sphere. The crystals belong to the centrosymmetric space group C2/c. The temperature dependent (1)H and (13)C NMR spectra indicate that both Bi(DOTA)(-) and Bi(DO3A-Bu)(-) complexes are fluxional. For Bi(DOTA), the Delta(deltadeltadeltadelta) right harpoon over left harpoon Lambda(lambdalambdalambdalambda) fluxionality was identified, and on the basis of the activation parameters, a synchronous motion was suggested for the fluxional motion resulting in the change of ring conformation and of the helicity of the complex. The transition state is supposed to be more symmetrical than the initial state. The deprotonated Bi(DO3A-Bu) has a highly asymmetric NMR structure in solution, and its fluxional motion is slower than that of Bi(DOTA)(-).     

修饰铂电极上Bi(Ш)的示波双电位滴定法

制备了Bi(Ⅲ)修饰铂电极,用循环伏安法表征了Bi(Ⅲ)在电极上的吸附特性,探讨了电极的响应机理。 通过优化实验条件,建立了一种测定Bi(Ⅲ)的示波双电位滴定法。 在0.1 mol/L的硝酸溶液中(pH=1.0),用制备的修饰铂电极作为双指示电极,以EDTA标准溶液滴定Bi(Ⅲ),利用示波器屏幕上荧光点的显著最大位移指示滴定终点。 Bi(Ⅲ)在1.19×10-4～1.44×10-2 mol/L时,回收率为99.8%～100.1%,检出限(S/N=3)为1.0×10-4 mol/L。 该修饰电极具有良好的稳定性和重现性,在含有1.0×10-2 mol/L Bi(Ⅲ)的溶液中,连续7次测定,所得终点电位值均在100 mV左右,其相对标准偏差(RSD)为0.04%。 应用该方法测定含铋样品,RSD值(n=7)小于0.25%,回收率为99.5%～100.5%,测定结果与指示剂法测定值相符。     

聚合物链的平均电偶矩及平均长度的一般计算法

本文在独立内旋转条件下,对聚合物链的平均电偶矩问题,作了比较彻底的处理。所得到的一般公式既可用来计算聚合物链的平均电偶矩,也可用来计算其平均长度。 应用文中的一般公式,对于(—CR_2—CR_2—)_(n/2),(-CH_2—CR_2—)_(n/2)和(—CH_2—CHR—)_(n/2)等链型分别作了具体计算,得到了一组有意义的结果。     

Determination of copper in white-metal bearing alloys

A method is proposed for the determination of copper in white-metal bearing alloys by direct controlled-potential electrolysis with a tantalum cathode at -0.32 V vs. SCE in a sulphate/bisulphate buffered electrolyte (pH 2) with fluoroboric acid and sodium tartrate as masking agents. Only Bi(III) interferes. Any co-deposited Bi can be corrected for by its spectrophotometric determination with Semi-Xylenol Orange after preconcentration with La(III) as carrier, from an ammoniacal solution containing the redissolved deposit. Any residual Cu(II) in the electrolyte is determined by spectrophotometry with 2,9-dimethyl-1, 10-phenanthroline. The standard deviation of this method has been found to be 0.03 mg (n = 12) and its relative standard deviation from 0.03 to 0.17%. It has been successfully used for referee analysis and certification of standard reference materials.     

Sensitive flotation-spectrophotometric determination of gold, based on the gold(I)-iodide-methylene blue system

The gold(I)-iodide-Methylene Blue (MB) system is suitable for flotation separation and spectrophotometric determination of gold. Under the optimum conditions [(MB(+))(AuI(2)(-))].3[(MB(+))(I(3)(-))] is formed, and floated with cyclohexane. The product is dissolved in methanol and its absorbance measured. The molar absorptivity is 3.4 x 10(5)1.mole(-1).cm(-1) at 655 nm. The proposed method is more than three times as sensitive as the Rhodamine B method. Pt, Pd, Ag and Hg interfere seriously, and Ir, Rh, Bi and Cd to a smaller extent. Preliminary separation of gold by precipitation with tellurium as a collector is recommended. The method has been applied to determination of gold traces (about 1 x 10(-4)%) in a copper sample.     

Determination of bismuth and copper using adsorptive stripping voltammetry couple with continuous wavelet transform

A new method is proposed for the determination of bismuth and copper in the presence of each other based on adsorptive stripping voltammetry of complexes of Bi(III)-chromazorul-S and Cu(II)-chromazorul-S at a hanging mercury drop electrode (HMDE). Copper is an interfering element for the determination of Bi(III) because, the voltammograms of Bi(III) and Cu(II) overlapped with each other. Continuous wavelet transform (CWT) was applied to separate the voltammograms. In this regards, wavelet filter, resolution of the peaks and the fitness were optimized to obtain minimum detection limit for the elements. Through continuous wavelet transform Symlet4 (Sym4) wavelet filter at dilation 6, quantitative and qualitative analysis the mixture solutions of bismuth and copper was performed. It was also realized that copper imposes a matrix effect on the determination of Bi(III) and the standard addition method was able to cope with this effect. Bismuth does not have matrix effect on copper determination, therefore, the calibration curve using wavelet coefficients of CWT was used for determination of Cu(II) in the presence of Bi(III). The detection limits were 0.10 and 0.05 ng ml⁻¹ for bismuth and copper, respectively. The linear dynamic range of 0.1-30.0 and 0.1-32.0 ng ml⁻¹ were obtained for determination of bismuth in the presence of 24.0 ng ml⁻¹ of copper and copper in the presence of 24.0 ng ml⁻¹ of bismuth, respectively. The method was used for determination of these two cations in water and human hair samples. The results indicate the ability of method for the determination of these two elements in real samples.     

Reaction between copper(I)-thiourea and bismuth(III)-thiourea complexes in presence of iodide. New spot-tests for copper(II) and bismuth(III)

New and very simple spot tests are described for the detection of Bi(III), Cu(II) and I(-) ions with limits of detection of 3, 8, and 75 mug/0.05 ml respectively. Tests are also described for such combinations as Bi(III) + I(-); Bi(III) + Cu(II); and Bi(III) + Cu(II) + I(-). All the tests are based on the formation of an orange or red-orange precipitate of bismuth(III)-copper(I)-iodide-thiourea complex, for which the formula [Bi(tu)(3)I(3).Cu(tu)(3)I] (where tu = thiourea) is proposed. This complex is produced in various ways by the interaction of Bi(III), Cu(II), and I(-) ions with thiourea. Most cations and anions do not interfere, but Tl(I), Cs(I), SO(2-)(3), S(2)O(2-)(3), EDTA, and oxidizing ions such as NO(-)(2), IO(-)(3), IO(-)(4), BrO(-)(3), and MnO(-)(4) do. The complex hexakis(thioureato)sulphatomonoaquodicopper(I) [Cu(2)(tu)(6)SO(4).H(2)O] is proposed as a new spot-test reagent for Bi(III) and I(-) ions, although the sensitivity for the latter is poor.     

In situ stress and nanogravimetric measurements during underpotential deposition of bismuth on (111)-textured Au

The surface stress associated with the underpotential deposition (upd) of bismuth on (111)-textured Au is examined, using the wafer curvature method, in acidic perchlorate and nitrate supporting electrolyte. The surface stress is correlated to Bi coverage by independent nanogravimetric measurements using an electrochemical quartz crystal nanobalance. The mass increase measured in the presence of perchlorate is consistent with the (2 x 2) and (p x square root 3)-2Bi adlayers reported in the literature. ClO(4)(-) does not play a significant role in the upd process. The complete Bi monolayer causes an overall surface stress change of about -1.4 N m(-1). We attribute this compressive stress to the formation of Bi-Au bonds which partially satisfy the bonding requirements of the Au surface atoms, thereby reducing the tensile surface stress inherent to the clean Au surface. At higher Bi coverage, an additional contribution to the compressive stress is due to the electrocompression of the (p x square root 3)-2Bi adlayer. In nitric acid electrolyte, NO(3)(-) coadsorbs with Bi over the entire upd region but has little fundamental impact on adlayer structure and stress.