纳米金催化一氧化碳氧化反应的理论研究

近年来,纳米金催化剂独特的催化性质,特别是其优异的低温催化氧化活性,引起了人们极大的研究热情.除低温选择氧化外,在精细化学品合成、大气污染物消除、氢能的转换和利用等领域也开发出了一系列有广泛应用前景的金催化反应.此外,体相金的化学惰性和纳米金的超高活性之间差异的“鸿沟”也引起了理论工作者浓厚兴趣,试图从原理上理解体相金和纳米金活性差异的根源. CO催化氧化是最具有代表性的研究金催化活性的化学反应,本文主要综述了近十多年来金催化 CO氧化反应理论计算方面的研究工作.一般认为, CO在纳米金表面的吸附是 CO氧化反应的初始步骤.密度泛函理论研究表明, CO在金表面的吸附强度主要与被吸附金原子的配位数有关：金配位数越低, CO的吸附能越强,部分研究结果表明两者之间存在近似的线性关系.我们研究发现, CO吸附强度也与被吸附金周围配位金原子的相对位置有关,其中位于正下方的配位金原子加强 CO吸附,而位于侧位的配位金原子则弱化 CO吸附,这显然削弱了 CO吸附与金配位数线性关系的可靠性.理论研究表明,在纯金表
　　面上 O2吸附强度一般很弱,只有在一些特殊结构的金团簇上才有较强的吸附,但在 Au/TiO2界面及 CeO2表面上 O2吸附较强.金表面原子氧的吸附和金的表面结构有关.我们发现,原子氧倾向于在金的表面形成一种线性的 O–Au–O结构以增加其稳定性.当金表面的氧覆盖度增大时,会形成一种金氧化物薄膜结构,其结构依赖于氧的化学势和金的表面结构.纳米金催化 CO氧化反应机理可能因体系、载体等的差异而不同.大部分理论计算结果表明,在纯金表面上 O2很难直接解离形成原子氧,因此反应机理可能是吸附的 CO先与 O2反应形成了一种 CO–O2中间体,然后解离形成 CO2.在 Au/TiO2和 Au/CeO2催化剂上 CO催化氧化机理争议很大,均有计算结果支持 LH机理和 M–vK机理.另外,根据实验上观察到了负载型纳米金能直接活化分子氧的结果,理论上也提出了分子氧先解离为原子氧再与 CO反应的氧解离机理.针对如何解离分子氧问题,人们分别提出了低配位金模型、正方形金结构模型、Ti5c模型及 Au/Ti5c模型等.我们也提出了一种独特的双直线 O–Au–O模型来理解 Au/TiO2或 Au/CeO2界面解离活化分子氧.理论计算结果表明,低配位的金,金和载体之间的电荷转移,以及金所表现出的强相对论效应对于纳米金的活性影响很大.需要特别指出的是,金的强相对论效应有助于理解金表面的 CO吸附与金配位的关系、金表面原子氧的吸附特性、金氧化物薄膜的结构和分子氧的活化等过程.我们认为,金的强相对论作用导致了体相金的化学惰性以及纳米金的活性,因此相对论效应的深入研究将有助于理解金催化 CO氧化反应机理,从而有助于深层次理解纳米金催化活性来源.     

焙烧温度对Au/Fe2O3选择性氧化富氢气体中CO催化性能的影响

甲醇重整在线制氢作为质子交换膜燃料电池的燃料成为当前研究的热点。受重整反应动力学及热力学的限制，使得甲醇重整气(富氢气体)中除含有大量的氢气外还含有少量的CO，CO极易吸附在燃料电池阳极催化剂表面，使电池性能下降，因而必须去除重整气中的CO，选择性氧化脱除富氢气     

Silver residues as a possible key to a remarkable oxidative catalytic activity of nanoporous gold

Recently, several forms of unsupported gold were shown to display a remarkable activity to catalyze oxidation reactions. Experimental evidence points to the crucial role of residual silver present in very small concentrations in these novel catalysts. We focus on the catalytic properties of nanoporous gold (np-Au) foams probed via CO and oxygen adsorption/co-adsorption. Experimental results are analyzed using theoretical models represented by the flat Au(111) and the kinked Au(321) slabs with Ag impurities. We show that Ag atoms incorporated into gold surfaces can facilitate the adsorption and dissociation of molecular oxygen on them. CO adsorbed on top of 6-fold coordinated Au atoms can in turn be stabilized by co-adsorbed atomic oxygen by up to 0.2 eV with respect to the clean unsubstituted gold surface. Our experiments suggest a linking of that most strongly bound CO adsorption state to the catalytic activity of np-Au. Thus, our results shed light on the role of silver admixtures in the striking catalytic activity of unsupported gold nanostructures.     

沉淀剂对AU/ZnO催化剂CO氧化性能及催化剂结构的影响

在25 C和进料中含水条件下,考察了由Na2CO3,(NH4)2CO3,NaOH和NH4OH等4种沉淀剂制备的Au/ZnO催化剂上CO氧化活性和稳定性.结果表明,沉淀剂影响Au/ZnO催化剂的前体组成、金粒子和ZnO粒子大小、比表面积及CO氧化性能.由NH4OH制备的Au/ZnO催化剂活性和稳定性较差,CO转化率只有15%;由其它3种沉淀剂制备的Au/ZnO催化剂的CO氧化活性和稳定性明显改善,可至少连续反应1 100 h,且保持CO完全氧化,其中Na2CO3是最佳沉淀剂.在反应过程中反应气氛可引起金粒子的聚集及在催化剂表面生成新的碱式碳酸锌物相.催化剂的稳定性与金粒子长大速度和碳酸根累积量有关.     

金催化作用的结构敏感性

金催化是纳米催化的代表性体系,金催化作用表现出复杂的结构敏感性。这篇综述总结了金催化作用研究的文献结果和我们利用从单晶到纳米晶的模型催化剂研究金催化作用的进展。展示了NO分解,CO氧化,丙烯在氢气和氧气气氛中环氧化等反应中金催化作用的结构敏感性和金催化剂的活性结构,讨论了金纳米粒子几何结构和电子结构、金纳米粒子–氧化物载体相互作用对金催化作用的影响和金表面低温高催化活性的来源,并展望了金催化作用结构敏感性的未来研究方向。     

Unravelling the origin of the high-catalytic activity of supported Au: a density-functional theory-based interpretation

Using first principles DF calculations we have studied the structural and catalytic properties of Au supported on TiOx-Mo(112) films. Our theoretical models are consistent with an initial (8 x 2) Mo(112)-Ti2O3 pattern which after Au deposition gives rise to ordered Au films that completely wet the surface. The oxidation of CO on model surfaces at coverage 1, 4/3, and 5/2 ML has been analyzed. The oxidation proceeds through a peroxo-like complex in which molecular oxygen is simultaneously bound to the CO and the surface. The energy barrier computed for a Au coverage of 4/3 ML is found significantly lower in agreement with the unusual high activity observed for this catalyst. The detailed analysis of the geometry and electronic structure provides a fundamental understanding of the reaction.     

Origin of Oxide sensitivity in gold-based catalysts: a first principle study of CO oxidation over Au supported on monoclinic and tetragonal ZrO2

The catalytic performance of Au/oxide catalysts can vary significantly upon the change of oxide species or under different catalyst preparation conditions. Due to its complex nature, the physical origin of this phenomenon remains largely unknown. By extensive density functional theory calculations on a model system, CO oxidation on Au/ZrO2, this work demonstrates that the oxidation reaction is very sensitive to the oxide structure. The surface structure variation due to the transformation of the oxide phase or the creation of structural defects (e.g., steps) can greatly enhance the activity. We show that CO oxidation on typical Au/ZrO2 catalysts could be dominated by minority sites, such as monoclinic steps and tetragonal surfaces, the concentration of which is closely related to the size of oxide particle. Importantly, this variation in activity is difficult to understand following the traditional rules based on the O2 adsorption ability and the oxide reducibility. Instead, electronic structure analyses allow us to rationalize the results and point toward a general measure for CO + O2 activity, namely the p-bandwidth of O2, with important implications for Au/oxide catalysis.     

Effect of supporting surface layers on catalytic activities of gold nanoparticles in CO oxidation

The surfaces of fumed silica materials were modified with a surface sol-gel process for catalysis applications. This surface-modification approach allows not only a monolayer growth of TiO(2) or Al(2)O(3) but also a stepwise double-layer growth of TiO(2)/TiO(2), Al(2)O(3)/Al(2)O(3), TiO(2)/Al(2)O(3), or Al(2)O(3)/TiO(2) on the surfaces of the silica materials with a monolayer precision. XRD analyses revealed that the coated monolayers and double layers of TiO(2) and Al(2)O(3) were amorphous. Gold nanoparticles were successfully deposited on the above six surface-modified silica materials via a deposition-precipitation method. The catalytic activities of these six gold catalysts for CO oxidation are highly dependent on the structures of their surface monolayers or double layers. The gold catalyst supported on the silica material functionalized with a TiO(2) monolayer (Au/TiO(2)) is the most active in both as-synthesized and oxidized forms, while the gold catalyst supported on the silica material functionalized with an Al(2)O(3)/TiO(2) double layer (Au/Al(2)O(3)/TiO(2)/SiO(2)) is the most active in the reduced form among the six catalysts. Surprisingly, the gold catalyst supported on the silica material functionalized with a TiO(2)/Al(2)O(3) double layer (Au/TiO(2)/Al(2)O(3)/SiO(2)) has much less activity than Au/Al(2)O(3)/TiO(2)/SiO(2) under all various treatments, underscoring the sensitivity of the catalytic activity to the structure of the supporting surfaces.     

Inhibition at perimeter sites of Au/TiO2 oxidation catalyst by reactant oxygen

TiO(2)-supported gold nanoparticles exhibit surprising catalytic activity for oxidation reactions compared to noble bulk gold which is inactive. The catalytic activity is localized at the perimeter of the Au nanoparticles where Au atoms are atomically adjacent to the TiO(2) support. At these dual-catalytic sites an oxygen molecule is efficiently activated through chemical bonding to both Au and Ti(4+) sites. A significant inhibition by a factor of 22 in the CO oxidation reaction rate is observed at 120 K when the Au is preoxidized, caused by the oxygen-induced positive charge produced on the perimeter Au atoms. Theoretical calculations indicate that induced positive charge occurs in the Au atoms which are adjacent to chemisorbed oxygen atoms, almost doubling the activation energy for CO oxidation at the dual-catalytic sites in agreement with experiments. This is an example of self-inhibition in catalysis by a reactant species.     

高分散的炭载Au纳米催化剂的制备、表征和催化活性

采用柠檬酸钠还原-胶体负载法, 制备了高分散的炭载Au纳米催化剂, 并以液相催化氧化葡萄糖为葡萄糖酸钠的反应评价了Au/C催化剂的活性. 研究结果表明, 金溶胶制备过程中柠檬酸钠的用量对粒子尺寸以及所获催化剂的催化活性有重要影响; 催化剂在多次使用之后活性的降低可能是由于在活性炭表面金粒子活性位点上形成的Au^δ＋-O^δ－化合态减少的缘故. 同时比较了制备的Au/C和商业Pd/C催化剂对葡萄糖的液相催化氧化反应, 证明Au/C催化剂明显优于Pd/C催化剂.     

Effects of preparation conditions of Au/FeOx/Al203 catalysts prepared by a modified two-step method on the stability for CO oxidation

Composite oxide FeO x /Al 2 O 3 -supported gold catalysts were prepared by a modified two-step method. The effects of preparation conditions on the initial catalytic activity and long-time stability were studied for CO oxidation. XRD, XPS and in situ FTIR were employed to investigate the state of FeO x and the species on the catalyst surface. The results showed that Au/FeO x /Al 2 O 3 catalysts prepared by this method exhibited high activity and high stability in a wide pH value range. Calcination pretreatment was proved to be beneficial to improving the activity and stability. The beneficial effects of FeO x acting as a structural promoter could be ascribed to the ability to supply active oxygen species. As the precursor of FeO x , Fe(NO 3 ) 3 is superior to FeCl 3 for obtaining higher stability.     

金催化剂上乙二醛氧气氧化合成乙醛酸的研究

利用沉积-沉淀法和溶液相还原法制备了系列金催化剂,以氧气氧化乙二醛合成乙醛酸为探针反应,进行了反应条件的优化,并通过对催化剂进行XRD、AAS、UV-Vis和XPS表征,分析了影响催化剂活性的因素.结果显示:与沉积-沉淀法相比,采用溶液相还原法制备的催化剂Au/ZrO2(L),金的实际负载量较高,表现出较高的催化活性,当溶液pH为7.7,反应温度为323 K时,乙醛酸收率达到6.2%.     

Influence of pretreatment conditions on low-temperature CO oxidation over Au/MOx/Al2O3 catalysts

Composite oxide MO_x/Al₂O₃ supported gold catalysts for low-temperature CO oxidation were prepared and investigated. The presence of transition metal oxide was proved to be beneficial to the improvement of catalytic performance of Au/Al₂O₃ catalysts for low-temperature CO oxidation. Furthermore, the influence of various pretreatment conditions on Au/MO_x/Al₂O₃ catalysts was studied carefully. The image of TEM showed that gold catalyst with small gold particles only in the form of a fine dispersion exhibited highly catalytic activity. The XPS, Fourier transform infrared (FTIR) spectroscopy characterization results of Au/FeO_x/Al₂O₃ catalyst showed that gold catalysts having partially oxidized gold species have the best catalytic performance. One possible pathway for CO oxidation on Au/FeO_x/Al₂O₃ catalyst is that the CO adsorbed on gold particles reacts with adsorbed oxygen, which is possible to occur on oxygen vacancies on the support or at the metal–support interface.     

镍掺杂对氧化铝纳米片负载金催化剂在CO氧化反应中的促进作用（英文）

负载型金催化剂在CO氧化反应中具有良好的低温活性,受到了研究者的广泛关注,其催化性能与载体的性质密切相关.氧化铝具有廉价易得、比表面积大和热稳定性好等优点.然而,作为一种非还原性载体,氧化铝提供活性氧物种的能力差,与还原性载体相比催化剂的CO氧化活性较低.理论计算和实验结果表明,在金催化剂中引入过渡金属镍能够有效促进氧分子在催化剂表面的吸附和活化,从而提升金催化剂活性.此外,过渡金属的存在能够提高金的分散度,增加活性位数目,防止在高温预处理过程中金颗粒的烧结,从而提高催化剂的活性和稳定性.基于上述考虑,本文在氧化铝纳米片合成过程中原位引入硝酸镍,以实现对氧化铝载体的改性,然后负载金并应用于CO氧化反应.结果表明,当载体中的Ni/Al摩尔比为0.05,金负载量为1wt%时,采用还原性气氛对催化剂进行预处理可以得到具有CO氧化性能优良的金催化剂, 20 oC下CO转化率即可达100%.预处理气氛能够显著影响催化活性,采用还原性气氛预处理后催化剂活性明显优于氧化性气氛预处理.采用X射线衍射(XRD)、高分辨透射电镜(HRTEM)、氢气程序升温还原(H2-TPR)、氧气程序升温脱附(O2-TPD)、CO吸附原位红外光谱(CO-DRIFT)和X射线光电子能谱(XPS)等表征手段进一步研究了镍掺杂对Au/Al2O3催化剂上CO氧化反应的促进作用机制.XRD测试未观察到明显的金或镍衍射峰,表明金或镍物种均为高分散.HRTEM结果进一步证实,引入镍物种后金颗粒的粒径由3.6 nm减小为2.4 nm,表明镍掺杂有助于提高金的分散度.而XPS结果显示,镍掺杂催化剂中金与镍存在电子转移,而镍仍以Ni O为主.H2-TPR结果表明,镍掺杂的催化剂前驱体中的金物种更容易被还原.O2-TPD结果证实,镍掺杂催化剂能够引入更多的氧空位,促进氧分子的吸附和活化,从而促进CO氧化反应的进行.CO-DRIFT结果表明,相比于氧化性气氛,采用还原性气氛预处理后金物种的电子云密度增加, CO吸附增强.而对于镍掺杂的催化剂,金物种吸附CO分子的能力进一步提高,有利于CO氧化反应的进行.综上,镍掺杂能够有效提高催化剂中金的分散度,增强催化剂对CO的吸附,促进氧气分子的吸附和活化,从而提高了催化剂的CO氧化活性.     

Effects of preparation conditions of Au/FeO_x /Al_2O_3 catalysts prepared by a modified two-step method on the stability for CO oxidation

Composite oxide FeO x /Al 2 O 3 -supported gold catalysts were prepared by a modified two-step method. The effects of preparation conditions on the initial catalytic activity and long-time stability were studied for CO oxidation. XRD, XPS and in situ FTIR were employed to investigate the state of FeO x and the species on the catalyst surface. The results showed that Au/FeO x /Al 2 O 3 catalysts prepared by this method exhibited high activity and high stability in a wide pH value range. Calcination pretreatm...     

Nature of reactive O2 and slow CO2 evolution kinetics in CO oxidation by TiO2 supported Au cluster

Recent experiments on CO oxidation reaction using seven-atom Au clusters deposited on TiO2 surface correlate CO2 formation with oxygen associated with Au clusters. We perform first principles calculations using a seven-atom Au cluster supported on a reduced TiO2 surface to explore potential candidates for the form of reactive oxygen. These calculations suggest a thermodynamically favorable path for O2 diffusion along the surface Ti row, resulting in its dissociated state bound to Au cluster and TiO2 surface. CO can approach along the same path and react with the O2 so dissociated to form CO2. The origin of the slow kinetic evolution of products observed in experiments is also investigated and is attributed to the strong binding of CO2 simultaneously to the Au cluster and the surface.     

不同载体稳定的纳米金催化剂室温催化氧化甲醛研究

甲醛是一种常见的室内空气污染物,人们针对其消除已经做了大量的研究工作.催化氧化法是脱除挥发性有机物的一种重要方法,能在较低温度下通过催化剂作用将甲醛完全氧化为无毒的CO2和H2O.所用催化剂主要为负载型贵金属催
　　化剂和非贵金属催化剂,但只有担载贵金属Pt或Pd的催化剂可在室温下将甲醛完全氧化,而非贵金属一般则需要较高的温度. Au催化剂是近年来催化领域的一个研究热点,但是关于纳米Au催化剂室温消除甲醛的研究较少.本课题组前期研究发现,以可还原性氧化物(CeO2, FeOx)为载体负载的Au催化剂具有优异的室温氧化甲醛活性;并且突破以可还原性载体负载金的传统思路,首次发现“惰性载体”γ-Al2O3,负载的金催化剂在室温、有水条件下具有优异的甲醛氧化活性.本文对比了还原性氧化物(CeO2, FeOx)和非还原性氧化物(Al2O3, SiO2和HSZM-5)载体负载金催化剂,研究了载体氧化还原性质对负载金催化剂在高空速(600000 ml/(g·s))条件下室温催化氧化甲醛的活性和稳定性影响.结果表明,在室温、高空速且相对湿度为50%的条件下, Au/Al2O3催化剂的初活性最高,且较为稳定. Au/SiO2和Au/HZSM-5催化剂的初活性虽然较高,但很快失活.而还原性氧化物载体(CeO2, FeOx)负载的金催化剂初活性较低,但是稳定性较好.通过电镜对负载金催化剂表面Au粒子大小的表征,并将粒子尺寸与负载金催化剂室温氧化甲醛初活性相关联,它与催化氧化甲醛反应速率成线性关系. Au粒子尺寸较小的催化剂(Au/Al2O3和Au/SiO2),在高空速条件下具有更高的氧化甲醛活性,而Au粒子尺寸较大的Au/FeOx催化剂活性较差.载体的氧化还原性质虽然不直接影响Au催化剂初活性,但直接影响催化剂稳定性.由于Au与SiO2或HZSM-5载体的相互作用较弱,导致反应过程中Au粒子聚集长大,使其失活较快;而Au/Al2O3催化剂表面则富含羟基物种,能够与Au形成配体或产生锚定作用,因此反应过程中金粒子没有明显长大.而表面中间物种的沉积并覆盖活性位是负载金催化剂缓慢失活的主要原因.     

Catalysis by supported gold: correlation between catalytic activity for CO oxidation and oxidation states of gold

X-ray absorption near-edge spectra and temperature-programmed oxidation and reduction data demonstrate that Au(I) and Au(0) are both present in working MgO-supported gold catalysts for CO oxidation. EXAFS data indicate gold clusters with essentially the same average diameter (about 30 A) in each catalyst sample. Thus, the results provide no evidence of an effect of gold cluster size on the catalytic activity, but both the catalytic activity and the surface concentration of Au(I) were found to decrease with increasing CO partial pressure (as Au(0) was increasingly formed), demonstrating that the catalytic sites incorporate Au(I).     

金负载量对低温水煤气变换Au/α-Fe2O3催化剂结构和性能的影响

采用共沉淀法制备了低温水煤气变换Au/α-Fe2O3催化剂。通过正交实验优化催化剂的还原活化条件，考察了金负载量对催化剂性能的影响。采用BET、XRD、UV-VIS、XRF、H2-TPR和O2-TPO等表征手段对催化剂的结构进行分析，并与其催化性能进行关联。结果表明，（1）采用10%-H2/N2还原气将催化剂在150 ℃原位还原9 h，其催化活性最高；（2）金的最佳负载量为8.00%，此时在催化剂制备过程中金的流失量较少，金粒子较小，也有利于抑制催化剂在反应过程中烧结；（3）TPR-TPO结果表明，金的负载量为8.00%时，Au/α-Fe2O3催化剂具有较易被还原、不易被氧化的性质，从而显示出最高催化活性。（4）Au/α-Fe2O3催化剂中的金以单质金（Au0）形式存在；其高活性与Au0-Fe3O4间的协同作用有关。     

Au/CeO2/SiO2催化CO低温氧化反应过程中CeO2的作用（英文）

采用具有分等级孔道结构的SiO2(HMS)为载体,通过润湿浸渍引入少量CeO2,经焙烧得到CeO2/HMS复合载体,然后采用沉积沉淀法负载上Au纳米粒子,得到Au/CeO2/HMS三元复合催化剂.通过X射线衍射、程序升温还原和原位红外光谱等手段表征了催化剂的结构.结果表明,CeO2的存在可控制Au颗粒的沉积并稳定载体上的纳米Au颗粒.Au/CeO2/HMS上CO低温氧化反应完全转化温度为60oC.高度分散的Au0可以活化CO,CeO2颗粒则可以提供反应需要的氧.稳定性测试结果显示,反应48h催化剂活性维持不变.