Preparation of body-temperature-triggered shape-memory polyurethane with biocompatibility using isosorbide and castor oil

Shape memory polyurethanes (SMPUs) have attracted much attention in the biomedical field because they can easily control the transition temperature (T_trans) to shape memory and are biocompatible. In this study, a shape memory polyurethane with both biocompatibility and a T_trans close to the body temperature was synthesized by using natural derivatives of isosorbide and castor oil in place of petroleum-based materials. Isosorbide and castor oil were used to form net points, and polycaprolactone diol (PCL diol) acted as the switching segment. The synthesized four polyurethane (PCL diol/isosorbide/castor oil, PICU-1, 2, 3, 4) with different isosorbide contents exhibited desired thermal and mechanical properties. In the thermo-cyclic shape memory testing experiment, the PICU series demonstrated good shape memory property, with more than 95% shape recovery ratio (R_r) and more than 90% shape fixity ratio (R_f), and PICU-3 recovered its shape within 20 s in a 37 °C water bath. In addition, the PICU series proved to be safe materials with excellent biocompatibility, as indicated by the observed C2C12 cells viability and proliferation. The stent made with the PICU-3 film showed near complete magnetization at 37 °C within 18 s and proved to be a suitable self-expanding stent.     

Electrically Conductive Polymeric Materials with High Stretchability and Excellent Elasticity by a Surface Coating Method

Electrically conductive polymer films with high stretchability and excellent elasticity were simply fabricated by coating a conductive layer on the surface of an elastomer film. The material used for the conductive layer was a high‐shear processed poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] triblock copolymer (SEBS)/multiwalled carbon nanotubes (MWCNTs) nanocomposite with 20 wt.‐% MWCNTs loading. The nanocomposites were first dissolved in toluene to form a stable solution and then were coated onto the SEBS film by spin coating. The alignment of MWCNTs in the coated layer and the interface between the base film and the coated layer were investigated. It was found that almost all the MWCNTs are aligned parallel to the base film and that there is good adhesion between the two layers. The fabricated films show high electrical conductivity and almost same stretchability and elasticity as the base film. Moreover, the films exhibit extremely high electrical conductive retention after applying high strain.

     

A 3D printable and self-healing polydimethylsiloxane elastomer

Silicone elastomers are broadly used in various fields because of their unique properties, such as flexibility, durable dielectric insulation, and excellent stability in hash environments. As a result, three-dimensional (3D) printing of silicone elastomers is frequently required to construct personalized structures. However, existing 3D-printing of silicone elastomers are less accurate, difficult to maintain shape, or require doping modification with thixotropic agents. Moreover, common 3D-printable silicone elastomers do not have self-healing capability, so they have to be discarded upon damaging. Herein, by introducing hydrogen bonds to improve the shape retention ability and induce network reversibility, we have developed a self-healing polydimethylsiloxane elastomer, which can be readily 3D-printed by fused deposition modeling (FDM) technology. We believe that this new silicone elastomer would be useful in the field of biomedical materials, flexible electronics, medical inserts, soft robots and so on.     

Synthesis of fullerenol-derived elastomers and conductive elastomers

Utilization of polyhydroxylated C₆₀ in a condensation reaction with diisocyanated oligo(tetramethylene oxide) led to the successful fabrication of elastomeric poly(urethane-ether) networks. These polymer networks exhibit interesting thermal behavior at low temperatures, improved tensile strength and elongation at ambient temperatures, and enhanced thermal mechanical stability at high temperatures. Design of conducting elastomers was made by carrying out an in situ polymerization of conductive polymer precursors in an interpenetrating fashion at the near-surface of polyhydroxylated C₆₀-hypercrosslinked elastomers. Results demonstrated that elastomers with an appreciable conductivity while retaining desirable elastic properties of the network can be achieved. The room-temperature conductivity of polyaniline interpenetrated (IPN) conducting elastomer was found to be 2.0 Scm⁻¹. The tensile strength and elongation at break of one conductive IPN elastomer was found to be 20 MPa and 480%, respectively. Interestingly, the strain dependent conductivity of these conducting elastomers was found to increase progressively above 200% of elongation. These results demonstrated, for the first instance, conductivity measurements of organic conducting elastomers at an elongation length of higher than 300%, showing a r.t. conductivity of >4.0 Scm⁻¹.     

A design of shape memory networks of poly(ε‐caprolactone)s via POSS‐POSS interactions

In this contribution, we reported a design of shape memory networks of poly(ε‐caprolactone)s (PCLs) via POSS‐POSS interactions. First, a series of novel organic‐inorganic PCL stars with polyhedral oligomeric silsesquioxane (POSS) termini were synthesized via the combination of ring‐opening polymerization of ε‐caprolactone and the copper (I)‐catalyzed cycloaddition of alkynyl with azido groups. It was found that the organic‐inorganic PCL stars significantly displayed shape memory properties with about 100% of recovery. The morphological observation showed that in the organic‐inorganic PCL stars, the POSS cages at the ends of PCL chains were self‐organized into the spherical POSS microdomains with the size of 10 to 20 nm in diameter. The POSS microdomains behaved as the netpoints, resulting in the formation of physically crosslinked networks. The novel physically crosslinked networks endowed the organic‐inorganic nanocomposites with shape memory properties.     

Extracting uncrosslinked material from low modulus sylgard 184 and the effect on mechanical properties

Commercial silicone elastomers are commonly used in soft materials research due to their easily tunable mechanical properties. However, conventional polydimethylsiloxane (PDMS) elastomers with moduli below ∼100 kPa contain uncrosslinked free molecules, which play a significant role in their behavior. To utilize these materials, it is important to quantify what role these free molecules play in the mechanical response before and after their removal. We present a simple and inexpensive extraction method that enables the removal of free molecules from a lightly crosslinked sheet of Sylgard 184, a commercially available PDMS elastomer. The materials can contain a majority of free molecules yet maintain a thin and flat geometry without fractures after extraction. Subsequently, we compare the modulus, maximum stretchability, and hysteresis behavior with mixing ratios ranging from 60:1 to 30:1, before and after extraction. We show that the modulus, maximum stretchability, and dissipation increase upon extraction. Moreover, our approach offers a route to prepare crosslinked silicone elastomers with a modulus as low as ∼20 kPa without free molecules from a commercially available kit. © 2020 Wiley Periodicals, Inc. J. Polym. Sci. 2020 , 58, 343–351     

A novel shape memory poly(ε‐caprolactone) network via UV‐triggered thiol‐ene reaction

A facile method to prepare shape memory polymers crosslinked by SiO₂ is described. A series of biodegradable shape memory networks were obtained through thiol‐ene reaction triggered by UV irradiation between surface‐thiol‐modified SiO₂ nanoparticles and end‐acrylate poly (ε‐caprolactone) (PCL). The highly selective thiol‐ene reaction ensured a uniform distribution of PCL chains between crosslinkers, contributing well‐defined network architecture with enhanced mechanical and shape‐memory properties. Thiol‐functionalized silica nanoparticle was characterized by using FTIR and XPS analysis, and ¹H NMR spectra was used to confirm the successful modification of terminal hydroxyl group of PCL diol. Surface‐modified silica particles were found well dispersible in acrylate‐capped PCL supported by SEM. Thermal and crystalline behaviors of the obtained polymers were analyzed by DSC and XRD, and DMA measurement proved good mechanical property. The shape memory behavior and tensile strength was somewhat tunable by the length of PCL. Acceptably, sample SiO₂‐SMP2k presented 99% recovery ratio and 97% shape fixity, and its relatively high tensile strength showed an attractive potential for biomedical application. Finally, a possible molecular mechanism accounting for the shape memory property was illustrated. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 692–701     

Preparation and characterization of composite nanofibers of polycaprolactone and nanohydroxyapatite for osteogenic differentiation of mesenchymal stem cells

Nanocomposites of nanohydroxyapatite (nHAP) dispersed in poly(?-caprolactone) (PCL) were prepared by electrospinning (ES) to obtain PCL/nHAP nanofibers. Nanofibers with similar diameters (340 ± 30 nm) but different nHAP concentrations (0-50%) were fabricated and studied for growth and osteogenic differentiation of bone marrow mesenchymal stem cells (MSCs). The nanofibrous membranes were subjected to detailed analysis for its physicochemical properties by scanning electron microscopy (SEM), thermogravimetric analysis, X-ray diffraction, Fourier-transform infrared spectroscopy, and mechanical tensile testing. nHAP particles (~30 nm diameter) embedded in nanofibers increased the nanofibrous membrane's ultimate stress and the elastic modulus, while decreased the strain at failure. When cultured under an osteogenic stimulation condition on nanofibers, MSCs showed normal phenotypic cell morphology, and time-dependent mineralization and osteogenic differentiation from SEM observations and alkaline phosphatase activity assays. The nanofibers could support the growth of mesenchymal stem cells without compromising their osteogenic differentiation capability up to 21 days and the enhancement of cell differentiation by nHAP is positively correlated with its concentration in the nanofibers. Energy dispersive X-ray analysis of Ca and P elements indicated mineral deposits on the cell surface. The mineralization extent was significantly raised in nanofibers with 50% nHAP where a Ca/P ratio similar to that of bone was found. The present study indicated that electrospun composite PCL/nHAP nanofibrous membranes are suitable for mineralization of MSCs intended for bone tissue engineering.     

Carbon-based conductive rubber composite for 3D printed flexible strain sensors

Polymeric-based flexible electronic devices are in high demand due to its wide range of applications. Natural rubber (NR) shows a great potential as matrix phase for flexible conductive polymer composites with its high elasticity and fatigue resistance. In this study, a new 3D printable conductive NR (CNR) composite was developed for strain sensor applications. Different contents of conductive carbon black (CCB) were mixed with NR latex to investigate the effect of the filler content on electrical and mechanical properties of the composites. The best-known CNR composite with the CCB content of 12 phr was selected in order to produce the feedstock for the stereolithography process (SLA). The morphological, electrical, and mechanical properties of cast and 3D-printed samples were investigated and compared. Although the 3D-printed CNR sample had slightly lower conductivity than the cast one, it possessed comparable tensile strength and elongation at break, with values of 12.4 MPa and 703%, respectively. In addition, electrical responses of the CNR samples were investigated to demonstrate the electromechanical property of the material as a strain sensor. The 3D-printed CNR sample exhibited the highest electromechanical sensitivity with a gauge factor (GF) of 361.4 (ε = 210%–300%) and showed good repeatability for 500 cycles. In conclusion, the development of this 3D printable functional material with great sensing capability will pave the way for innovative designs of personalized sensing textiles and other smart wearable devices.     

Synthesis and Properties of High-Performance Thermoplastic Poly(ester-ether) Elastomers Reinforced by <Emphasis Type="Italic">N,N</Emphasis>′-Bis(2-carboxyethyl) Pyromellitimide Moieties

A series of poly(ester-imide-ether), consisting of soft segments from poly(tetramethylene glycol) and N,N′-bis(2-carboxyethyl) pyromellitimide and hard segments based on 1,4-butanediol and N,N′-bis(2-carboxyethyl) pyromellitimide, were synthesized via the melt polycondensation. The chemical structures of the prepared elastomers were confirmed by Fourier transform infrared spectroscopy and ¹HNMR, respectively. The results indicated that the introduction of aromatic bisimide groups endows the elastomers with excellent thermal stability and mechanical property, which increase with the increment of imide unit content in the prepared elastomers. Additionally, compared to the poly(ester-ether) elastomer, these poly(esterimide-ether) fibers displayed stronger tensile strength and better low-temperature elastic recovery property.     

Enhanced dielectric performance of a block copolymer‐polythiophene nanocomposite

Dielectric elastomer actuators (DEAs) transform electrical energy into mechanical work. However, despite displaying exceptional features, the low permittivity of elastomers restricts their application. Hence, to overcome this limitation, DEAs are fabricated by dispersing poly(3‐methylthiophene acetate) (P3TMA), a polarizable conducting polymer, into poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS), a thermoplastic elastomer with excellent mechanical properties. Although high‐quality SEBS:P3TMA films are obtained for all compositions (between 0.5 and 20 wt % P3TMA), their thickness and surface roughness increase with the nano‐sized filler content. Moreover, the conducting particles are well integrated into the SEBS network with no evidence of aggregation or significant change in the mechanical properties of the composites. P3TMA, which forms encapsulated conductive domains within the polymeric matrix, improves the dielectric behavior of SEBS:P3TMA by increasing their dielectric constant with low dielectric losses and no current leakage. Thus, indicating the potential future application of these nanocomposites as elastomer actuators or high energy density capacitors. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1896–1905     

Transparent and shape-memory cellulose paper reinforced by vitrimer polymer for efficient light management and sustainability

The functional paper holds significant potential in some special fields, which has achieved great development. Nevertheless, using cellulose paper to fabricate functional paper, which integrates transparency, robustness, flexibility, shape memory, and sustainability, remains a challenge. Herein, the vitrimer precursor was vacuum impregnated into cellulose paper and then in-situ polymerized to develop a vitrimer-cellulose paper (VCP) with transparency, shape manipulation, robustness, and sustainability. Taking advantage of the vitrimer’s dynamic performance, the resulting VCP demonstrated excellent optical transparency (transmittance of 84%, haze of 75%), enhanced mechanical strength (tensile strength of 80.5 MPa), chemical resistance, thermal-triggered shape manipulation, and reprocessing. Noteworthily, VCP possessed outstanding light management capability with effective light propagating and scattering performance. Furthermore, VCP laminate showed increased mechanical property with the increased layers, and it can be reprocessed to a bulk composite after crushing. These incorporated merits of VCP make a promising candidate for light management and sustainable building application.

     

Thin and high conductive multi-walled carbon nanotubes/polydimethylsiloxane composite film prepared via solvent method as strain sensors

Flexible strain sensors based on conductive fillers and flexible polymers possessed significant advantages in human motion detection. Preparing a strain sensing layer with high electrical conductivity and excellent mechanical property under high content of conductive filler contributed to the stability of flexible strain sensors. In this study, MWCNTs/PDMS composite film was prepared by the organic solvent method. The microstructure, electrical conductivity, mechanical property, and piezoresistive characteristics of the composite film at different MWCNTs contents were characterized and discussed. When the mass fraction of MWCNTs in the composite film was 5%, the composite film exhibited a high electrical conductivity of 9.56 S/m while maintaining ideal mechanical properties, and the film thickness was just about 180 μm. The relationship between electrical signals and film strain was performed. The piezoresistive characteristic results demonstrated that the prepared composite film could be used as flexible strain sensor for human motion detection. The prepared thin MWCNTs/PDMS composite film in this paper illustrated high conductive and desired flexibility, and was an alternative material for human motion detection.     

Static secondary ion mass spectrometry for the surface characterisation of individual nanofibres of polycaprolactone functionalised with an antibacterial additive

Electrospinning (ES) of polymer solutions generates non-woven webs of nanofibres. The fibre diameter ranges between 10 nm and 1 μm depending on the operating conditions. Surface functionalisation can be performed by the use of suitable additives. Detailed characterisation of the molecular composition at the fibre surface is a key issue. Biodegradable nanowebs with potential antibacterial activity have been prepared by ES of solutions containing polycaprolactone (PCL) and a functionalising additive with PCL segments and hexyldimethylammonium groups (PCLhexaq). Static secondary ion mass spectrometry with Bi₃⁺ projectiles has been applied to individual nanofibres. The positive ion mass spectra contain several signals with high structural specificity allowing the presence of PCLhexaq to be traced back in spite of its low concentration (0.16–1.4% w/w relative to PCL) and its structural similarity to the PCL fibre matrix. Imaging of structural ions visualises the homogeneous distribution of PCLhexaq over the fibre surface. Quantifying the surface concentration of PCLhexaq relative to that of PCL reveals electric field-driven surface enrichment of the additive during ES. Finally, nanofibres subjected to leaching in water for up to 72 h have been analysed. The PCLhexaq surface concentration decreases almost linearly with time at a rate of 0.6% h⁻¹.     

牛血清白蛋白在医用聚氨酯弹性体表面的吸附

制备了具有较好机械性能的异佛尔酮二异氰酸酯(IPDI)型聚氨酯弹性体胶片, 并进行表面肝素化处理, 得到抗凝血医用导管材料. 将聚氨酯胶片浸泡在牛血清白蛋白(BSA)水溶液中, 利用稀溶液黏度法研究了牛血清白蛋白在聚氨酯胶片表面的动态吸附情况, 并采用界面校正黏度方程计算溶液浓度变化. 研究发现, 牛血清白蛋白分子能迅速吸附到聚氨酯胶片表面, 但达到吸附平衡需要较长时间. 牛血清白蛋白在聚氨酯表面吸附后的溶液中分子构象发生变化.     

Triple shape memory effect in multiple crystalline polyurethanes

Remembering more than one permanent shape is an attractive research topic for shape memory materials (SMMs). In this paper, multiple crystalline shape memory polyurethanes (SMPUs) are prepared with PCL10000 and PTMG2900 by a three‐step polymerization method. DSC and WAXD results show that the obtained polyurethane contains, simultaneously and independently, two kinds of crystals. In addition, it is confirmed through DMA analysis that reversible soft phase and hard domains are formed in the PCL‐PTMG based SMPU system; and two‐step modulus decreases at low temperature range can be obtained in the SMPU with suitable mass proportion of PCL to PTMG, e.g., 1:7. Thus, shape memory effect (SME) can be achieved in this system. Moreover, it is found that the PTMG soft segment dominates the shape memory effect when the PCL mass is lower than that of PTMG; while the PCL soft segment dominates the SME when PCL mass is higher than that of PTMG; and a two‐step programing shape recovery can be achieved when the mass proportion of PCL/PTMG reaches a balance value, e.g., 3:5. Copyright © 2009 John Wiley & Sons, Ltd.     

Two‐way multi‐shape memory properties of peroxide crosslinked ethylene vinyl‐acetate copolymer (EVA)/polycaprolactone (PCL) blends

Rare studies have investigated on the 2‐way shape memory crosslinked blends with multiple shape memory behavior up to date. To consider the merit of commercial cost‐competitive crystalline polymers, ethylene vinyl‐acetate copolymer (EVA) / polycaprolactone (PCL) blends (60/40 and 30/70) were peroxide‐cured to form the 2‐way multi‐shape memory crosslinked blends using a melt‐blending method. Both resins were selected to have a similar controlled crosslinking degree, which allowed us to distinctly evaluate their actuation contributions from the cooling‐induced elongation (crystallization) and from the entropy‐driven elongation during cooling process, respectively. In the 2‐way process for the 60/40 system, 2 respective peaks contributed from the cooling‐induced crystallization of EVA and PCL in the cooling curves based on the strain derivate rates at various temperatures were observed. After the cooling process under the loading stress of 150 kPa, the 2‐step heating‐induced contraction process with increasing temperature started at 54.1°C above the melting temperature of PCL at 52.3°C and EVA at 78.3°C, demonstrating 2‐way multi‐shape memory behavior. The multi‐step behavior was more prominent at higher PCL composition and higher load for the 30/70 system. It was found that the entropy‐driven contribution to the overall actuation magnitude increased with increasing nominal loads due to the increased orientation of molecular networks in the blends. The current approach offers numerous possibilities in preparing 2‐way multi‐shape memory crosslinked blends.     

Hydrophobic association and ionic coordination dual crossed-linked conductive hydrogels with self-adhesive and self-healing virtues for conformal strain sensors

As a promising functional material, conductive hydrogel has attracted extensive attention, especially in flexible sensor field. Despite the recent developments, current hydrogels still experience several issues, such as limited stretchability, lack of self-recovery and self-healing capability, and insufficient self-adhesion. Herein, dual cross-linked (DC) poly (AA-co-LMA)_SDS/Fe³⁺ hydrogels are fabricated subtly on the basis of ionic coordination interactions and the poly (AA-co-LMA)_SDS hydrophobic association networks, which may provide one plausible routine to compensate the mentioned drawback of hydrogels. The hydrophobic association and ionic coordination networks work synergistically to endow the hydrogels remarkable stretchability (>1200%), high-fracture strength (≈ 820 kPa), and excellent self-healing capability. In addition, the DC hydrogel-based strain sensors displayed a broad sensing range (0 ∼ 900%), conspicuous sensitivity (strain 0% ∼ 200%, gauge factor = 0.53; strain 200% ∼ 500%, gauge factor = 1.23; strain 500% ∼ 900%, gauge factor = 2.09), and pronounced durability. What's more, the self-adhesive feature ensures the strain sensor always forming a good conformal contact with the skin during human movements and displaying remarkable bidirectional detection capability.     

Synergistic Effects of Beta Tri‐Calcium Phosphate and Porcine‐Derived Decellularized Bone Extracellular Matrix in 3D‐Printed Polycaprolactone Scaffold on Bone Regeneration

Bone‐derived extracellular matrix (ECM) is widely used in studies on bone regeneration because of its ability to provide a microenvironment of native bone tissue. However, a hydrogel, which is a main type of ECM application, is limited to use for bone graft substitutes due to relative lack of mechanical properties. The present study aims to fabricate a scaffold for guiding effective bone regeneration. A polycaprolactone (PCL)/beta‐tricalcium phosphate (β‐TCP)/bone decellularized extracellular matrix (dECM) scaffold capable of providing physical and physiological environment are fabricated using 3D printing technology and decoration method. PCL/β‐TCP/bone dECM scaffolds exhibit excellent cell seeding efficiency, proliferation, and early and late osteogenic differentiation capacity in vitro. In addition, outstanding results of bone regeneration are observed in PCL/β‐TCP/bone dECM scaffold group in the rabbit calvarial defect model in vivo. These results indicate that PCL/β‐TCP/bone dECM scaffolds have an outstanding potential as bone graft substitutes for effective bone regeneration.     

Dynamic elastomers based on bio-derived crosslinker

Petroleum-derived monomers are the most common building blocks for ester-based thermosets. Bio-derived thermoset elastomers are becoming viable alternatives to conventional thermosets. Herein, we developed a biobased vitrimer-type thermoset elastomers using abundant and sustainable raspberry ketone as feedstock. We utilize raspberry ketone to create building blocks for dynamic oxime chemistry and crosslinked these through free radical polymerization with poly(ethylene glycol) methyl ether methacrylate as a comonomer. In contrast to other dynamic networks based on ester bonds, which need catalysts, this is undesirable since catalyst deactivation or leaching lowers its effect over time and may impair reuse. This network incorporates catalyst-free bond exchange reactions in catalyst-dependent polyester networks by substituting oxime-esters for typical ester linkages. The elastomer exhibits stress relaxation, a low glass transition temperature (T_g) (−55 to −40.2°C) and tensile strength up to 5.2 ± 3.0 kPa. Furthermore, the dynamic oxime transesterification exchange mechanism allows elastomers to be reprocessed using a hot press at 160°C and 8 × 10³ kPa pressure. After reprocessing, the tensile strength of elastomers can be recovered up to 78.1 ± 10.9%. This work integrates the principles of catalyst-free dynamic exchange process and mechanical recycling coupled with biobased components to provide a rational solution towards conventional elastomers. In the future, these elastomers can be exploited for the development of hydrogels, recyclable elastomers, and commodity plastics.