Influence of empty hole on crack running in PMMA plate under dynamic loading

The influence of original prefabricated empty hole on dynamic crack propagation was studied. The dynamic behavior of crack propagation due to the impacting of drop hammer on the defective PMMA medium of manufactured hole defect (different extent of left shift, respectively, for L = 110 mm, L = 111.25 mm and L = 112.5 mm) was conducted using the test system of digital laser dynamic caustics (DLDC). The stress intensity factor and velocity at the running crack tip were analyzed. Moreover, the recently developed distinct lattice spring model (DLSM) was validated using the experimental data. It was found that the numerical modeling can reproduce the experimentally observed phenomena. Combining the experimental and numerical results, it can be concluded that the influence of empty hole defects of brittle materials on dynamic fracturing is great.     

Measurement of the dynamic fracture toughness with notched PMMA specimen under impact loading

In the present study three-point-bend impact experiments were conducted using an instrumented Charpy pendulum with a laser displacement measurement to better understand the correlation between impact velocity and the dynamic effects observed on the load-time curves. The experiments were performed at impact velocities ranging from 1 to 4 m/s.The aim of this work is to measure the dynamic fracture toughness at high impact velocities where the classical method is limited by the inertial effects. The direct measurements of the specimen deflection are successfully used for the toughness evaluation. The results obtained with this method, which are compared to other studies, indicate that this approach seems promising for brittle materials such as PMMA.     

Determination of crack growth kinetics in non-reinforced semi-crystalline thermoplastics using the linear elastic fracture mechanics (LEFM) approach

The aim of this study was to find a satisfactory method to characterize the fatigue crack growth behavior of non-reinforced, semi-crystalline thermoplastic polymers using linear elastic fracture mechanics (LEFM). For this, crack growth curves (crack length versus cycle number) as well as crack growth kinetics curves (crack growth rate da/dN versus amplitude stress intensity factor ΔK) had to be generated. As methods suggested by ISO 15850 and ASTM E 647-11 failed to provide satisfactory results for the crack growth curves, a more advanced method was searched for and finally found in the literature. Regarding the crack growth kinetics curve, the idea of the calculation was based on methods recommended in ISO 15850 and ASTM E 647-11. However, these methods had to be considerably modified and improved in order to get accurate results with little scatter. The whole methodology was developed and verified with fatigue crack growth tests on two semi-crystalline thermoplastics (polyoxymethylene POM and polyetheretherketone PEEK).     

Dynamic fracture testing of polymethyl-methacrylate (PMMA) single-edge notched beam

Dynamic fracture in single-edge notched polymethyl-methacrylate (PMMA) beams have been investigated by three-point-bending impact testing with a drop-weight machine. A high-speed camera combined with the digital image correlation (DIC) method is used to capture the impact-induced crack initiation and propagation, as well as the beam deformation fields and the open mode strain at the original notch tip. The crack propagation length is recorded and the instantaneous crack velocity is calculated. Furthermore, the dynamic fracture toughness K_Id is quantified from the loading-displacement relations at different impact velocities. The effects of the impact velocity and impact energy on dynamic fracture toughness, fracture initiation strain, as well as the corresponding influences on the fracture propagation velocity, are discussed.     

Assessment of nanocomposites based on unsaturated polyester resin/nanoclay under impact loading

The aim of this study is to investigate the performance of nanoclay reinforced unsaturated polyester (UP) resin under impact loads. Nanocomposite specimens containing nanoclay in 0, 1.5, and 3 (wt%) were prepared by melt mixing method. X‐ray diffraction, transmission electron microscopy analysis, scanning electron microscope photographs, and viscosity changes in liquid state resin confirmed exfoliation and intercalation of the nanoclay in the UP resin system used. Tensile modulus showed an increase with increase in nanoclay content. However, the tensile strength and elongation at break exhibited reducing performance with increase in nanoclay content. Izod impact test results indicated better performance for the specimens containing nanoclay reinforcements, with 1.5 (wt%) of nanoclay specimens showing the highest value. High velocity impact tests were carried out using gas gun in velocity range of 20–100 m/sec and harden steel hemispherical tip projectile with diameter of 8.7 mm and weight of 11.54 g. Results for high velocity impact test indicated better performance by the specimens containing nanoclay, with 1.5 (wt%) nanoclay showing the highest attained value. Damage assessments of impact area for all specimens showed spalling type brittle failure with punch out and sever fragmentation pattern. Copyright © 2011 John Wiley & Sons, Ltd.     

Characterization and modeling of slow crack growth behaviors of defective high-density polyethylene pipes using stiff-constant K specimen

In this study, slow crack growth (SCG) resistances of defective and normal high density polyethylene (HDPE) pipes were measured using the stiff-constant K (SCK) specimen, where the stress intensity factor (SIF) was maintained at a constant value within a certain crack length range. A significantly reduced SCG resistance was observed in the defective pipe; a detailed procedure for evaluating SCG kinetics using the SCK specimen has been provided herein. The results of a fracture surface analysis indicate that the white window patterns, resulting from poor carbon black dispersion, are the main reason for poor SCG performance. In addition, a crack layer (CL) model was derived for the SCK specimen geometry and was compared with experimental results. It was observed that the crack and process zone growth resistance parameters were significantly lower in the case of the defected pipe than those in the case of the normal pipe.     

Tensile,fracture and impact behavior of transparent Interpenetrating Polymer Networks with polyurethane-poly(methyl methacrylate)

Transparent Interpenetrating Polymer Networks (IPNs) with poly(methyl methacrylate) (PMMA) as the stiff phase and polyurethane (PU) as the ductile phase with varying PMMA:PU ratios in the range of 90:10 to 70:30 were formulated. Static tensile and fracture tests indicate significant failure strain and crack initiation toughness enhancements with a loss of stiffness relative to PMMA. Dynamic fracture tests were conducted using a long-bar impact loading apparatus in conjunction with an optical method and high-speed photography. Low-velocity impact tests were also performed using a drop-tower. Dynamic fracture and low-velocity impact responses show that an optimum range of PMMA:PU ratios in the IPNs can produce enhanced fracture toughness and impact energy absorption capability when compared to PMMA. Fractographic examination supports macro-measurements by showing a distinct change in surface morphology associated with improved macroscale fracture toughness.     

Determination of slow crack growth behaviour of polyethylene pressure pipes with cracked round bar test

In this work, a short time test method to determine the slow crack growth behaviour of samples made out of pipes was evaluated. The cracked round bar (CRB) method used provides results below 48 h with brittle fracture surfaces, which indicates the type of slow crack growth failure. To evaluate the usability of the method, the results were compared with well-known tests such as notch pipe test, 2 notch creep test and instrumented Charpy impact tests. The results indicate that the CRB test can be used to predict long term slow crack growth behaviour of PE pipes.     

Separation of proteins with a molecular mass difference of 2 kDa utilizing preparative double-inverted gradient polyacrylamide gel electrophoresis under nonreducing conditions: application to the isolation of 24 kDa human growth hormone

A method for separating proteins with a molecular mass difference of 2 kDa using SDS-PAGE under nonreducing conditions is presented. A sample mixture containing several human growth hormone (hGH) isoforms was initially separated on a weak anion-exchange column. Fractions rich in 24 kDa hGH as determined by analytical SDS-PAGE were pooled and further separated by cation-exchange chromatography. The fractions pooled from the cation-exchange chromatography contained two hGH isoforms with a 2 kDa molecular mass difference according to SDS-PAGE analysis, 22 and 24 kDa hGH. The 22 and 24 kDa hGH were separated using continuous-elution preparative double-inverted gradient PAGE (PDG-PAGE) under nonreducing conditions. The preparative electrophoresis gel was composed of three stacked tubular polyacrylamide matrices, a 4% stacking gel, a 13-18% linear gradient gel, and a 15-10% linear inverted gradient gel. Fractions containing purified 24 kDa hGH were pooled and Western blot analysis displayed immunoreactivity to antihGH antibodies. PDG-PAGE provides researchers with an electrophoretic technique to preparatively purify proteins under nonreducing conditions with molecular mass differences of 2 kDa.