Synthesis and characterization of novel environmentally friendly shape memory polyurethanes based on poly(epsilon-caprolactone) diol/castor oil mixtures

A new category of polyurethane plastics (PUs) was obtained from poly (ε-caprolactone) diol/castor oil mixture as a dual-component of their soft segment and hexamethylene diisocyanate (HDI) as the hard segment. The main aim of this study was to explore the effect of castor oil on content chemical structure, dynamic and mechanical properties and low temperature heat induced shape memory of the obtained polyurethane system. The chemical structure of samples was confirmed by Fourier transforms infrared (FTIR) and nuclear magnetic resonance (NMR) spectroscopy. Differential scanning calorimetry (DSC) was carried out to study thermal transitions of synthesized polyurethanes. At 50 mol % of oil, the polyurethane showed the highest enhancement in tensile strength (54%) and Young’s modulus (23%) compared to PU-0. The PU containing 50 mol % of oil was nearly recovered by 99%.     

Influence of Isosorbide on Glass‐Transition Temperature and Crystallinity of Poly(butylene terephthalate)

Copolyesters of isosorbide and 1,4‐butane diol were prepared by Ti(OBu)₄‐catalyzed transesterifications with dimethyl terephthalate in bulk at temperatures up to 250°C. The content of isosorbide was considerably lower than expected from the feed ratio and the molar masses were low, so that no DSC measurements were conducted. Copolycondensations of isosorbide and 1,4‐butane diol with terephthaloyl chloride were either performed in dichloromethane at 40°C or in toluene at 100°C. The second method gave the higher molar masses. However, both series of polycondensations had the content of isosorbide roughly paralleled the feed ratios in common. The DSC measurements revealed that even 6 mol% of isosorbide is sufficient to raise the glass‐transition temperature (T_g) by 10–12°C (up to 55°C). With 50 mol% of isosorbide, the T_g reaches 100°C. Yet, incorporation of isosorbide also reduces the melting temperature T_m and the degree of crystallinity, and a mol percentage above 30% prevents crystallization completely. In summary, incorporation of isosorbide allows for fine‐tuning of T_g and T_m of poly(butylene terephthalate) over a wide range.     

Characterization of cyclic and non-cyclic poly-(ether-urethane)s bio-based sugar diols by a combination of MALDI-TOF and NMR

Matrix-assisted laser desorption/ionization (MALDI) mass spectrometry and NMR spectroscopy have been applied for characterization of novel poly-(ether-urethane)s (PolyEU) based on various diols derived from starch and two diisocyanates. First, numerous polyurethanes soft and hard blocks were prepared by polyaddition of isosorbide (3), isomannide (4) or isoidide (5) with 4,4′-diphenylmethane diisocyanate (MDI) (7) or hexane-1,6-diisocyanate (HDI) (8). The polyaddition of isoidide and MDI yields 85% of polyurethane hard block with high inherent viscosity (η_inh = 0.35 dL/g) with linear chains as the main products. In the case of polyurethane based on isosorbide and MDI a large amount of cyclic compounds was formed with relatively high viscosity (η_inh = 0.29 dL/g) and good yield (77%). This polyurethane hard block presents a high glass transition temperature (T_g = 183 °C) and an excellent thermal stability until 250 °C (T_g = 77 °C of the polyurethane soft block based on isosorbide and HDI). Second, polyaddition of an aliphatic diol (6a) based on isosorbide and MDI yielded new poly-(ether-urethane) soft-hard blocks with quantitative yield (>95%). This polymer is soluble in common organic solvents and has a number-average molecular weight of 7950 Da with a polydispersity index of 1.43. The MALDI-TOF spectrum of this poly-(ether-urethane) indicated the formation of high molar fraction of cycles (Ca and Cb). The pure cyclic poly-(ether-urethane) soft-hard block presents a T_g of 141 °C.     

Design of cross-linked semicrystalline poly(ε-caprolactone)-based networks with one-way and two-way shape-memory properties through Diels-Alder reactions

Cross‐linked poly(ε‐caprolactone) (PCL)‐based polyesterurethane (PUR) systems have been synthesized through Diels–Alder reactions by reactive extrusion. The Diels–Alder and retro‐Diels–Alder reactions proved to be useful for enhancing the molecular motion of PCL‐based systems, and therefore their crystallization ability, in the design of cross‐linked semicrystalline polymers with one‐way and two‐way shape‐memory properties. Successive reactions between α,ω‐diol PCL (PCL₂), furfuryl alcohol, and methylene diphenyl 4,4′‐diisocyanate straightforwardly afforded the α,ω‐furfuryl PCL‐based PUR systems, and subsequent Diels–Alder reactions with N,N‐phenylenedimaleimide afforded the thermoreversible cycloadducts. The cross‐linking density could be modulated by partially replacing PCL‐diol with PCL‐tetraol. Interestingly, the resulting PUR systems proved to be semicrystalline cross‐linked polymers, the melting temperature of which (close to 45 °C) represented the switching temperature for their shape‐memory properties. Qualitative and quantitative measurements demonstrated that these PUR systems exhibited one‐way and two‐way shape‐memory properties depending on their cross‐linking density.     

Facile scalable one-step wet-spinning of surgical sutures with shape memory function and antibacterial activity for wound healing

Surgical suture is commonly used in clinic due to its action in accelerating the process of wound healing.However,difficultly handling in minimally invasive surgery and bacteria-induced infection usually limit its use in a wide range of applications.Here,we report a facile scalable strategy to fabricate surgical sutures with shape memory function and antibacterial activity for wound healing.Specifically,a shape memory polyurethane(SMPU) with a transition temperature(T_(trans)) at 41.3℃ was synthesized by adjusting the mole ratio of the hard/soft segment,and then the shape memory surgical sutures containing polyhexamethylene biguanide hydrochloride(PHMB) as a model drug for antibacterial activity were fabricated by a facile scalable one-step wet-spinning approach,in which PHMB was directly dissolved in the coagulation bath that enable its loading into the sutures through the dual diffusion during the phase separation.The prepared sutures were characterized by their morphology,mechanical properties,shape memory,antibacterial activity,as well as biocompatibility before the wound healing capability was tested in a mouse skin suture-wound model.It was demonstrated that the optimized suture is capable of both shape memory function and antibacterial activity,and promote wound healing,suggesting that the facile scalable one-step wet-spinning strategy provides a promising tool to fabricate surgical sutures for wound healing.     

A novel shape memory poly(ε‐caprolactone) network via UV‐triggered thiol‐ene reaction

A facile method to prepare shape memory polymers crosslinked by SiO₂ is described. A series of biodegradable shape memory networks were obtained through thiol‐ene reaction triggered by UV irradiation between surface‐thiol‐modified SiO₂ nanoparticles and end‐acrylate poly (ε‐caprolactone) (PCL). The highly selective thiol‐ene reaction ensured a uniform distribution of PCL chains between crosslinkers, contributing well‐defined network architecture with enhanced mechanical and shape‐memory properties. Thiol‐functionalized silica nanoparticle was characterized by using FTIR and XPS analysis, and ¹H NMR spectra was used to confirm the successful modification of terminal hydroxyl group of PCL diol. Surface‐modified silica particles were found well dispersible in acrylate‐capped PCL supported by SEM. Thermal and crystalline behaviors of the obtained polymers were analyzed by DSC and XRD, and DMA measurement proved good mechanical property. The shape memory behavior and tensile strength was somewhat tunable by the length of PCL. Acceptably, sample SiO₂‐SMP2k presented 99% recovery ratio and 97% shape fixity, and its relatively high tensile strength showed an attractive potential for biomedical application. Finally, a possible molecular mechanism accounting for the shape memory property was illustrated. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 692–701     

Surface morphology and electrical properties of polyurethane nanofiber webs spray‐coated with carbon nanotubes

Multiwalled carbon nanotubes (MWNTs) were spray‐coated on electrospun polyurethane nanofiber webs for electrical conductive application. For the effective coating of MWNTs, hyperbranched polyurethane (HBPU) was used by blending with linear polyurethane, which was synthesized in the A₂ + B₃ approach using poly(ε‐caprolactone)diol, 4,4′‐methylene bis(phenylisocynate), and castor oil. SEM measurements showed that the MWNTs could be coated well along the surface of nanofibers when the HBPU was blended in the linear polyurethane nanofibers. Blending of HBPU in the nanofibers also affected the electrical conductivity of MWNT‐coated nanofiber webs. The low electrical resistance from 20 to 400 Ω/sq was obtained for MWNT‐coated nanofiber webs and their electrical resistance decreased with an increase of spraying frequency. As a potential application of MWNT‐coated nanofiber webs, the electrical heating effect because of applied voltage was demonstrated. Copyright © 2011 John Wiley & Sons, Ltd.     

Development of biobased polyurethane‐imides from maleinized cottonseed oil and castor oil

An eco‐friendly coating system, which is largely biobased, has been developed from castor and cottonseed oil. Cottonseed oil was functionalized with maleic anhydride by “ene” reaction to give maleinized cottonseed oil (MACSO); the anhydride groups were reacted with isocyanates to yield –NCO terminated polyurethane prepolymer. The prepolymer was further chain extended with hydroxyl groups of castor oil to give polyurethane‐imides (PUIs). The cross‐linked films thus obtained had good mechanical properties, and the imide groups in the backbone improved the corrosion resistance of PUIs as revealed by potentiodynamic polarization study. With increasing content of MACSO, thermal stability, glass transition temperatures (T_g), tensile strength, and corrosion resistance of resulting PUIs significantly increased.     

Nano/micro-scale morphologies of semi-interpenetrating poly(ε−caprolactone)/tung oil polymer networks: Isothermal and non−isothermal crystallization kinetics

The isothermal and non-isothermal crystallization kinetics of pure poly(ε−caprolactone) (PCL) and its blends with crosslinked tung oil were investigated as a function of composition, crystallization temperature, and heating rate using differential scanning calorimetric (DSC). The PCL/tung oil semi-interpenetrating polymer networks of different compositions were prepared via cationic polymerization of tung oil in the presence of homogenous solutions of PCL. This unique and relatively new in-situ polymerization and compatibilization blending technique created nano/micro-scale morphologies that cannot be obtained with the traditional melt-processing and/or solvent casting methods. Blends with different miscibility, phase behaviors, and morphologies (miscible, partially miscible, and immiscible) were observed as a function of composition with a constant concentration of boron trifluoride diethyl etherate (BFE) cationic initiator. The morphology of the semi-interpenetrating polymer networks was performed using scanning electron microscopy (SEM). Miscible blends with a single T_g for PCL ≤ 10 wt.%. were observed. While, on the other hand, partially miscible blends with two distinct T_gs and nanoscale morphologies and average particle sizes as small as 100 nm were observed for blends with 20 ≤ PCL wt.% ≤ 30. Immiscible blends with microscale highly interconnected, co-continuous two-phase morphology and two distinct T_gs were detected for 50 wt.% PCL. Both isothermal and non-isothermal crystallization kinetics were strongly influenced by the different miscibility and morphology of the blends. The isothermal and non-isothermal crystallization kinetics of PCL/tung oil blends were analyzed on the basis of Avrami and modified Avrami approaches, respectively. A substantial decrease in the isothermal (longer half time) and non-isothermal (T_m shifted to lower temperature) crystallization kinetics was observed as the concentration of PCL increased in the blends up to 30 wt.% due to the partially miscibility of the blends in this composition range. In a contrast, for 50 wt.% PCL blend, a considerable increase in the crystallization kinetics (isothermal and non-isothermal) was detected due to the highly interconnected, co-continuous two-phase morphology.     

Shape memory induced structural evolution of high performance copolyimides

In this work, two kinds of high temperature shape memory copolyimides were prepared and the shape memory cycles induced structural evolution of macromolecular chains was investigated in detail. The glass transition temperature (T_g) of poly(benzoxazole‐co‐imide) (PI1) and poly(benzimidazole‐co‐imide) (PI2) are 280 °C and 355 °C, respectively. The results show that PI1 could keep stable macromolecular chain structure under shape memory cycles and exhibit outstanding shape memory performance (R_f > 98%, R_r > 97%) under different stretch condition. Whereas, shape memory cycles induced orientation with more ordered macromolecular chains packing is formed for PI2 after several thermal mechanical cycles, which strongly affect physical crosslinking points, thermal mechanical properties as well as shape memory behaviors. The study on macroscopic property and microscopic structure evolution will promote a better understanding of the shape memory effect of polyimides and accelerate development of high performance polyimides for shape memory applications. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 3858–3867     

Synthesis and characterization of photocrosslinked poly(ε‐caprolactone)s showing shape‐memory properties

Poly(ε‐caprolactone) (PCL) with a pendent coumarin group was prepared by solution polycondensation from 7‐(3,5‐dicarboxyphenyl) carbonylmethoxycoumarin dichloride and α, ω‐dihydroxy terminated poly(ε‐caprolactone) with molecular weights of 1250, 3000, and 10,000 g/mol. These photosensitive polymers underwent a rapid reversible photocrosslinking upon exposure to irradiation with alternating wavelengths (>280/254 nm) without a photoinitiator. The thermal and mechanical properties of the photocrosslinked films were examined by means of differential scanning calorimetry and stress–strain measurements. The crosslinked films exhibited elastic properties above the melting temperature of the PCL segment along with significant decrease in the ultimate tensile strength and Young's modulus. Shape‐memory properties such as strain fixity ratio (R_f) and strain recovery ratio (R_r) were determined by means of a cyclic thermomechanical tensile experiments under varying maximum strains (ε_m = 100, 300, and 500%). The crosslinked ICM/PCL‐3000 and ‐10,000 films exhibited the excellent shape‐memory properties in which both R_f and R_r values were 88–100% for tensile strain of 100–500%; after the deformation, the films recovered their permanent shapes instantaneously. In vitro degradation was performed in a phosphate buffer saline (pH 7.2) at 37 °C with or without the presence of Pseudomonas cepacia lipase. The presence of the pendent coumarin group and the crosslinking of the polymers pronouncedly decreased the degradation rate. The crosslinked biodegradable PCL showing a good shape‐memory property is promising as a new material for biomedical applications. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2422–2433, 2009     

Shape Memory Properties and Enzymatic Degradability of Poly(ε‐caprolactone)‐Based Polyurethane Urea Containing Phenylalanine‐Derived Chain Extender

Biodegradable shape memory polymers are promising biomaterials for minimally invasive surgical procedures. Herein, a series of linear biodegradable shape memory poly(ε‐caprolactone) (PCL)‐based polyurethane ureas (PUUs) containing a novel phenylalanine‐derived chain extender is synthesized. The phenylalanine‐derived chain extender, phenylalanine‐hexamethylenediamine‐phenylalanine (PHP), contains two chymotrypsin cleaving sites to enhance the enzymatic degradation of PUUs. The degradation rate, the crystallinity, and mechanical properties of PUUs are tailored by the content of PHP. Meanwhile, semicrystalline PCL is not only hydrolytically degradable but also vital for shape memory. Good shape memory ability under body temperature is achieved for PUUs due to the strong interactions in hard segments for permanent crosslinking and the crystallization‐melt transition of PCL to switch temporary shape. The PUUs would have a great potential in application as implanting stent.     

Study on poly(ε‐caprolactone)‐based shape memory copolymer fiber prepared by bulk polymerization and melt spinning

In this paper, a poly(ε‐caprolactone) (PCL)‐based shape memory polyurethane fiber was prepared by melt spinning. The shape memory switching temperature was the melting transition temperature of the soft segment phase mainly composed of PCL at 47°C. The mechanical properties especially shape memory effect were explicitly characterized by thermomechanical cyclic tensile testing. The results suggest that the prepared fiber has shape memory effects. The prepared 40 denier shape memory fiber had a tenacity of about 1.0 cN/dtex, and strain at break 562–660%. The shape fixity ratio reached 84% and the recovery ratio reached 95% under drawing at high temperature and thermal recovery testing.¹ Finally, the fiber thermal/mechanical properties were measured using differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA). Copyright © 2007 John Wiley & Sons, Ltd.     

Conductive stretchable shape memory elastomers combining with electrical stimulation for synergistic osteogenic differentiation

The natural extracellular matrix (ECM) possessed varying biomechanical properties which played important roles in the dynamic cellular microenvironment. However, for the conventional bone tissue engineering scaffolds, stretchability and shape memory property were normally absent. Thus, the behaviors of responsive changes required in dynamic physiological settings were unsatisfactory. Herein, a series of conductive polyurethane shape memory elastomers (PCL-IPDI-AT) were synthesized, which based on conductive amino capped aniline trimer (AT), isophorone diisocyanate (IPDI) and poly(ԑ-caprolactone) (PCL). The conductive elastomers possessed high elasticity and flexibility, especially, the breaking elongation of copolymer with 15% AT content was up to 570 ± 56%. The mechanical properties of elastomers could be adjusted by regulating the content of AT in copolymers. The conductive elastomers exhibited excellent shape fixity ratio and good shape recovery ability at 37 °C. The electrical conductivity of elastomers was measured via the standard van der Pauw four-probe method. They were all around 10⁻⁷ S/cm and similar to that in human physiological environments. On the one hand, excellent cytocompatibility was demonstrated by the viability and proliferation results of MC3T3-E1 pre-osteoblasts seeded on the elastomer. On the other hand, the elastomer could synergistically promote the osteogenic differentiation compared to PCL in terms of ALP activity, calcium deposition, and bone-related protein and gene expression levels as combined with electrical stimulation (ES). Specifically, the ALP activity for conductive elastomer under ES was notably improved by 1.4-fold compared to PCL at 7 days. Overall, the conductive elastomers displayed excellent stretchability, shape memory property, fatigue resistance and osteogenic bioactivity. They may be applied as bone substitutes for electrical-signal-sensitive bone tissue engineering.     

Calorimetric and Dielectric Study of the Segmented Biodegradable Poly(ester‐urethane)s Based on Bacterial Poly[(R)‐3‐hydroxybutyrate]

Two series of segmented poly(ester‐urethane)s were synthesized from bacterial poly[(R)‐3‐hydroxybutyrate]‐diol (PHB‐diol), as hard segments, and either poly(ε‐caprolactone)‐diol (PCL‐diol) or poly(butylene adipate)‐diol (PBA‐diol), as soft segments, using 1,6‐hexamethylene diisocyanate as a chain extender. The hard‐segment content varied from 0 to 50 wt.‐%. These materials were characterized using ¹H NMR spectroscopy and GPC. The polymers obtained were investigated calorimetrically and dielectrically. DSC showed that the T_g of either the PCL or PBA soft segments are shifted to higher temperatures with increasing PHB hard‐segment content, revealing that either the PCL or PBA are mixed with small amounts of PHB in the amorphous domains. The results also showed that the crystallization of soft or hard segments was physically constrained by the microstructure of the other crystalline phase, which results in a decrease in the degree of crystallinity of either the soft or hard segments upon increase of the other component. The dielectric spectra of poly(ester‐urethane)s, based on PCL and PHB, showed two primary relaxation processes, designated as α_S and α_H, which correspond to glass–rubber transitions of PCL soft and PHB hard segments, respectively. Whereas in the case of other poly(ester‐urethane)s, derived from PBA and PHB, only one relaxation process was observed, which broadens and shifts to higher temperature with increasing PHB hard‐segment content. It was concluded from these results that our investigated materials exhibit micro‐phase separation of the hard and soft segments in the amorphous domains.     

Molecular composites composed of castor oil‐modified poly(ε‐caprolactone) and self‐assembled hydroxystearic acid fibers

After (R)‐12‐hydroxystearic acid (HSA) was mixed at 100 °C with the castor oil‐modified poly(ε‐caprolactone) (CO‐PCL) prepared by the ring‐opening polymerization of ε‐caprolactone in the presence of castor oil, the mixture was gradually cooled to room temperature to give a solidified CO‐PCL/HSA composite. The CO‐PCL/HSA sample showed an exothermic peak at around 67–71 °C which was lower than the melting point of HSA (76.8 °C), indicating the formation of mesogenic HSA aggregates. The rheological measurement of the CO‐PCL/HSA revealed the formation of HSA organogel at around 67–55 °C during the cooling process from the melt. Furthermore, the polarized and normal optical microscopic analyses of CO‐PCL/HSA on the cooling stage revealed that anisotropic fibrous materials are formed at around 60 °C and then the fibrous network propagated over the matrix polymer. The flexural modulus and storage modulus of the CO‐PCL/HSA composite increased with increasing HSA content. The CO‐PCL/HSA composite annealed at 60 °C for 2 h on the cooling process had a higher flexural and storage modulus than the sample without annealing. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1281–1289, 2010     

Synthesis and Thermal Properties of Biodegradable Poly(ester‐urethane)s Based on Chemo‐Synthetic Poly[(R,S)‐3‐hydroxybutyrate]

A series of telechelic oligo[(R,S)‐3‐hydroxybutyrate]‐diols (PHB‐diols) was synthesized from ethyl (R,S)‐3‐hydroxybutyrate (ethyl (HB)) and four different aliphatic diols, namely, 1,4‐butanediol, 1,6‐hexanediol, 1,8‐octanediol and 1,10‐decanediol by transesterification and condensation in bulk. The structures of the synthesized oligomers were confirmed by ¹H NMR spectroscopy and MALDI‐TOF mass spectroscopy. The use of 1,4‐butanediol results in an oligoester with hydroxyl functionality of approximately 2. In the case of the higher aliphatic diols, the number average functionalities were found to be lower than 2. These differences were ascribed to side reactions which occur during polymerization, yielding unreactive end groups. Other novel families of biodegradable poly(ester‐urethane)s were synthesized either from PHB‐diol alone, or PHB‐diol mixed with poly(ε‐caprolactone)‐diol (PCL‐diol), poly(butylene adipate)‐diol (PBA‐diol) or poly(diethylene glycol adipate)‐diol (PDEGA‐diol). In each case, 1,6‐hexamethylene diisocyanate was used as a nontoxic connecting agent. The homopolymers prepared from PCL‐diol, PBA‐diol and PDEGA‐diol were also synthesized for the sake of comparison. All the prepared copolymers possess high molecular weight with glass transition temperature (T_g) values varying from –54 to –23°C. Some of the prepared copoly(ester‐urethane)s are partially crystalline with melting temperatures (T_m's) varying from 37 to 56°C.     

Effect of comonomer on thermal/mechanical and shape memory property of L‐lactide‐based shape‐memory copolymers

In this study, three kinds of L ‐lactide‐based copolymers, poly(lactide‐co‐glycolide) (PLGA), poly(lactide‐co‐p‐dioxanone) (PLDON) and poly(lactide‐co‐caprolactone) (PLC), were synthesized by the copolymerization of L ‐lactide (L) with glycolide (G), or p‐dioxanone (DON) or ε‐caprolactone (CL), respectively. The copolymers were easily soluble in common organic solvents. The compositions of the copolymers were determined by ¹H‐NMR. Thermal/mechanical and shape‐memory properties of the copolymers with different comonomers were compared. Moreover, the effect of the chain flexibility of the comonomers on thermal/mechanical and shape‐memory properties of the copolymers were investigated. The copolymers with appropriate lactyl content showed good shape‐memory properties where both the shape fixity rate (R_f)and the shape recovery rate (R_r) could exceed 95%. It was found that the comonomers with different flexible molecular chain have different effects on their thermal/mechanical and shape‐memory properties. Among them, PLGA has the highest mechanical strength and recovery rate while PLC copolymer has high recovery rate when the lactyl content exceeded 85% and the lowest transition temperature (T_trans). Copyright © 2007 John Wiley & Sons, Ltd.     

Thermomechanical properties of cured isophtalic polyester resin modified with poly(ε-caprolactone)

The effect of a low profile additive, poly(ε-caprolactone) (PCL), on the thermal and mechanical properties of unsaturated polyester resins (UP) was investigated by differential scanning calorimetry (DSC), dynamic mechanical thermal analysis (DMTA), and tensile tests. The morphology of the systems has been studied by scanning electronic microscopy (SEM). Two PCL molecular mass were selected (PCL2: M _n = 2000 g mol⁻¹ and PCL50: M _n = 50000 g mol⁻¹) to analyze the influence of the molecular mass and the content of PCL on the UP resins and to establish the relation between thermomechanical behavior and morphology. DSC and DMTA glass transition temperatures (T _g) of the UP cured samples containing PCL indicate that PCL2 is miscible with UP whereas for UP + PCL50 system, T _g values are very close to the ones corresponding to neat UP. Besides in UP + PCL2 systems, one phase morphology is observed in which PCL2 would act as solvent of the reacting mixture along curing process; however, UP + PCL50 systems present phase-separated morphology. The presence of PCL2 and PCL50 in UP resin leads to a decrease of the tensile strength and the Young′s modulus as much notorious as the PCL concentration increases. For UP + PCL2 system the elongation at fracture increases in relation to neat UP, increasing as well with the PCL content.     

Shape memory effect and recovery stress property of carbon nanotube/waterborne epoxy nanocomposites investigated via TMA

Shape memory polymers (SMPs) have received great attention and scientific interest in widespread technological development during last few decades. Besides the development of novel SMPs, various techniques have been practiced for characterization of shape memory effect (SME) of SMPs. In this study, the shape memory effect and recovery stress property of the carbon nanotube (CNT)/waterborne epoxy (WEP) nanocomposites below and above the glass transition temperature (T_g) of the nanocomposites and under isostrain and isostress were systematically investigated via thermal mechanical analysis (TMA), respectively. The experimental results showed that the nanocomposites exhibit excellent shape memory effect. The shape memory fixity and recovery ratios were approximately 100% even below glass transition temperature (T_g). A remarkable point is that the strain of the nanocomposites suddenly increased with the temperature decreasing in a certain period of the heating-cooling cycles under isostress condition and the strain increment increased with temperature in general. Especially at low temperature, the recovery stress was very sensitive to temperature under isostrain condition of ±0.25 °C temperature with differential of 25.5 °C developed pressure difference of 0.20 MPa. Moreover, TMA is a practical method for quantifying the SME and recovery stress properties of SMPs and their composites.