Instantaneous fluctuation velocity and skewness distributions upstream of transition onset

The development of streamwise orientated disturbances through the boundary layer thickness prior to transition onset for zero-pressure gradient boundary layer flow under the influence %Tu = 4.2 is presented. The analysis concentrates on the development of the maximum positive and negative of the fluctuation velocity in order to gain further insight into the transition process. The average location of the peak negative fluctuation velocity over a range of Reynolds numbers was measured in the upper portion of the boundary layer at y/δ ≈ 0.6, whereas the location of the peak positive value was measured at y/δ ≈ 0.3. The disturbance magnitude of the negative fluctuation velocity increased beyond that of the positive as transition onset approached. The distribution and disturbance magnitude of the maximum positive and negative fluctuation velocities indicate that the initiation of transition may occur on the low-speed components of the flow that are lifted up to the upper region of the boundary layer. This is in qualitative agreement with recent direct numerical simulations on the breakdown of the flow on the lifted low-speed streaks near the boundary layer edge. The results presented in this investigation also demonstrate the increased physical insight gained by examining the distributions of the maximum positive and negative of the streamwise fluctuation velocity component associated with the low- and high-speed streaks, compared to time-averaged values, in determining what structures cause the breakdown to turbulence.     

Effects of small changes in initial conditions on mixing layer three-dimensionality

Conclusions An experimental study which shows the effects of relatively small changes in the initial conditions on the development of the three-dimensional structure of a plane mixing layer originating from laminar boundary layers has been completed. It was shown that while the exact shapes and positions of the streamwise vortex structures are not the same for the two initial conditions, their overall distribution, reorganization and decay are very similar. The present results imply that while some of the specific details of the streamwise vortex structure may be facility dependent, a relatively strong structure, which produces significant three-dimensionality, should form in all mixing layers originating from laminar boundary layers. After some initial readjustments, the structure will appear in the form of counter-rotating pairs of streamwise vortices which, in the mean, grow with the mixing layer and decay in strength.The present results also serve as a warning that small changes in initial conditions may significantly affect the Reynolds stress distributions in the near-field. The most likely mechanism for this is through the effects of very small changes in initial boundary layer properties on the details (strength and location) of the spanwise vortex roll-up. Despite these relatively large differences in the near-field, both mixing layers attain comparable turbulence structure and growth rates in the far-field. In addition, the behavior of the streamwise vortex structure does not appear to be affected by the differences in the near-field Reynolds stress distributions.     

Vortex reynolds number in turbulent boundary layers

The effects of vortex Reynolds number on the statistics of turbulence in a turbulent boundary layer have been investigated. Vortex Reynolds number is defined as the ratio of circulation around the vortex structure to the fluid viscosity. The vortex structure of the outer region was modeled and a full numerical simulation was then conducted using a high-order spectral method. A unit domain of the outer region of a turbulent boundary layer was assumed to be composed of essentially three elements: a wall, a Blasius mean shear, and an elliptic vortex inclined at 45° to the flow direction. The laminar base-flow Reynolds number is roughly in the same range as that of a turbulent boundary layer based on eddy viscosity, and the vortex-core diameter based on the boundary-layer thickness is nearly the same as the maximum mixing length in a turbulent boundary layer. The computational box size, namely, 500, 150, and 250 wall units in the streamwise, surface-normal, and spanwise directions, respectively, is approximately the same as the measured quasi-periodic spacings of the near-wall turbulence-producing events in a turbulent boundary layer. The effects of vortex Reynolds number and the signs of the circulation on the moments of turbulence were examined. The signs mimic the ejection and sweep types of organized motions of a turbulent boundary layer. A vortex Reynolds number of 200 describes the turbulence moments in the outer layer reasonably well.     

Response of the boundary layer developing over a blunt-nosed flat plate to free-stream non-uniformities

The response of the boundary layer on a flat plate with blunt nose to infinitesimally small non-uniformity in the freestream velocity along the span has been studied. The non-uniformity was shown to excite boundary-layer disturbances similar to streaks or Klebanoff modes generally observed in experiments conducted with a high level of free-stream turbulence. The boundary layer disturbances have a predominantly streamwise velocity component and exhibit transient growth. In contrast to streaks generated by streamwise vortices impinging on the sharp nose of a plate, the disturbances produced by free-stream non-uniformity interaction with a blunt nose have a different level of growth. Their maximal amplification scales with the Reynolds number, based on the size of nose bluntness and is almost independent of the spanwise period of disturbances. This difference was shown to be caused by additional amplification of disturbances via vortex lines stretching around the leading edge.     

Velocity statistics and flow structures observed in bypass transition using stereo PTV

It is known from smoke visualizations that in a transitional boundary layer subjected to free-stream turbulence, streaks appear and eventually break down to turbulence after wavy motions. In order to observe the streaky structures directly, a stereo particle-tracking velocimetry system using hydrogen bubbles in a water channel has been developed and validated against laser Doppler velocimetry. Mean flow statistics show good agreement with previous results. With the developed measurement system, the instantaneous spanwise distribution of the streamwise and wall-normal velocities can be measured fast enough to resolve the time development of the streaky structures. Measurements of instantaneous spanwise distributions of the streamwise and wall-normal velocity disturbances show strong negative correlation between the wall-normal and streamwise velocities in the streaks. Published online: 19 November 2002     

Large Eddy Simulations in Turbines: Influence of Roughness and Free-Stream Turbulence

The individual and coupled effects of the incoming free-stream turbulence (FST) and surface roughness on the transition of a separated shear layer over a flat plate is numerically investigated using Large eddy simulation (LES). The upper wall of the test section is inviscid and specifically contoured to impose a streamwise pressure distribution over the flat plate to simulate the suction surface of a low pressure turbine (LPT) blade. The interaction of the streamwise streaks due to FST and roughness with the separated shear layer is captured. The streaks induced by FST are intermittent in nature and the streaks due to roughness are steady for a given topology of the rough surface. Both FST and roughness promoted near-wall mixing. The ‘net effect’ of mixing in the pre-separated region is manifested by a shift the inflection point of the velocity profile towards the wall. This resulted in the upstream shift of the transition point and a significant reduction in the size of the separation bubble. The combined effect of FST and roughness further reduced the size of separation bubble. The streamwise evolution of the boundary layer parameters has been compared for different cases. The potential ‘roughness benefit’ obtained in the case of highly loaded turbine blades in terms of its considerable reduction of profile loss is also shown.     

Numerical simulation on evolution of subharmonic low-speed streaks in minimal channel turbulent flow

The evolution of low-speed streaks in the turbulent boundary layer of the minimum channel flow unit at a low Reynolds number is simulated by the direct numer- ical simulation （DNS） based on the standard Fourier-Chebyshev spectral method. The subharmonic sinuous （SS） mode for two spanwise-aligned low-speed streaks is excited by imposing the initial perturbations. The possibilities and the physical realities of the turbulent sustaining in the minimal channel unit are examined. Based on such a flow field environment, the evolution of the low-speed streaks during a cycle of turbulent sus- taining, including lift-up, oscillation, and breakdown, is investigated. The development of streamwise vortices and the dynamics of vortex structures are examined. The results show that the vortices generated from the same streak are staggered along the streamwise direction, while the vortices induced by different streaks tilt toward the normal direction due to the mutual induction effect. It is the spatial variations of the streamwise vortices that cause the lift-up of the streaks. By resolving the transport dynamics of enstrophy, the strength of the vortices is found to continuously grow in the logarithmic layer through the vortex stretching mechanism during the evolution of streaks. The enhancement of the vortices contributes to the spanwise oscillation and the following breakdown of the low-speed streaks.     

Turbulence measurements in the inlet plane of a centrifugal compressor vaneless diffuser

Detailed flow measurements at the inlet of a centrifugal compressor vaneless diffuser are presented. The mean 3-d velocities and six Reynolds stress components tensor are used to determine the turbulence production terms which lead to total pressure loss. High levels of turbulence kinetic energy were observed in both the blade and passage wakes, but these were only associated with high Reynolds stresses in the blade wakes. For this reason the blade wakes mixed out rapidly, whereas the passage wake maintained its size, but was redistributed across the full length of the shroud wall. Peak levels of Reynolds stress occurred in regions of high velocity shear and streamline curvature which would tend to destabilize the shear gradient. Four regions in the flow are identified as potential sources of loss - the blade wake, the shear layers between passage wake and jet, the thickened hub boundary layer and the interaction region between the secondary flow within the blade wake and the passage vortex. The blade wakes generate most turbulence, with smaller contributions from the hub boundary layer and secondary flows, but no significant contribution is apparent from the passage wake shear layers.     

The effect of streamwise vortices on the turbulence structure of a separating boundary layer

A high Reynolds number flat plate turbulent boundary layer is investigated in a wind-tunnel experiment. The flow is subjected to an adverse pressure gradient which is strong enough to generate a weak separation bubble. This experimental study attempts to shed some new light on separation control by means of streamwise vortices with emphasize on the change in the boundary layer turbulence structure. In the present case, counter-rotating and initially non-equidistant streamwise vortices become and remain equidistant and confined within the boundary layer, contradictory to the prediction by inviscid theory. The viscous diffusion cause the vortices to grow, the swirling velocity component to decrease and the boundary layer to develop towards a two-dimensional state. At the position of the eliminated separation bubble the following changes in the turbulence structure were observed. The anisotropy state in the near-wall region is unchanged, which indicates that it is determined by the presence of the wall rather than the large scale vortices. However, the turbulence in the outer part of the boundary layer becomes overall more isotropic due to an increased wall-normal mixing and a significantly decreased production of streamwise fluctuations. The turbulent kinetic energy is decreased as a consequence of the latter. Despite the complete change in mean flow, the spatial turbulence structure and the anisotropy state, the process of transfer of turbulent kinetic energy to the spanwise fluctuating component seems to be unchanged. Local regions of anisotropy are strongly connected to maxima in the turbulent production. For example, at spanwise positions in between those of symmetry, the spanwise gradient of the streamwise velocity cause significant production of turbulent fluctuations. Transport of turbulence in the spanwise direction occurs in the same direction as the rotation of the vortices.     

Observations of meandering superstructures in the roughness sublayer of a turbulent boundary layer

The existence of meandering superstructures in a turbulent boundary layer overlying irregular roughness is explored with high-frame-rate particle-image velocimetry measurements within the roughness sublayer at moderate Reynolds number. Elongated streamwise fields of view reconstructed from this data using a Taylor’s hypothesis approach revealed spanwise-meandering regions of low-streamwise-momentum fluid that extended several boundary-layer thicknesses in the streamwise direction. Such signatures are consistent with previous observations of superstructures in smooth-wall turbulence. Counter-rotating wall-normal vortex cores were found to reside along the spanwise boundaries of these superstructure patterns, consistent with the spatial characteristics of hairpin vortex packets.     

Recognition of coherent structures in the boundary layer of a low-pressure-turbine blade for different free-stream turbulence intensity levels

Particle Image Velocimetry (PIV) has been adopted to analyze the instantaneous flow field developing on a high-lift turbine blade profile operating under low and elevated free-stream turbulence conditions (FSTI). Results reported in the paper allow us to analyze the dynamics leading to transition and separation of the suction side boundary layer, looking to generation, propagation and breakdown of coherent structures observed in the two different FSTI cases. To this end, measurements have been performed in two orthogonal planes. Results obtained in the blade-to-blade plane allow the detailed characterization of the propagation of Kelvin–Helmholtz (KH) rolls generating, at low FSTI condition, as a consequence of a non-reattaching separation. Otherwise, data in the wall-parallel plane allow recognizing the presence of three-dimensional disuniformities induced at high FSTI by low and high speed streaks (Klebanoff mode). The sinuous breakdown of boundary layer streaks generates other complex three-dimensional coherent structures such as hairpin or cane-like vortices that induce transition. Proper Orthogonal Decomposition (POD) has been adopted to in depth characterize these structures, thus further explaining the mechanisms through which the free-stream turbulence intensity modify the transition/separation processes of the suction side boundary layer of an highly loaded low pressure turbine blade.     

Spectral structure and linear mechanisms in a rapidly distorted boundary layer

The aim of the present work is to investigate the spectral structure of a rapidly distorted boundary layer that develops on a flat plate in presence of a localised patch of roughness or/and grid-generated freestream turbulence. We observe that, at a certain distance downstream of the roughness patch the boundary layer exhibits a bimodal shape in the energy spectrum of the streamwise velocity fluctuations, similar to that found in a fully-turbulent boundary layer at relatively high Reynolds numbers. The physical mechanism that gives rise to the low-wavenumber peak in the spectrum, which represents long streamwise motions or “superstructures”, is identified to be the interaction of the broadband disturbances with the region of high shear near the wall in the boundary layer. We next show that the flat-plate boundary layer combined with surface roughness and grid turbulence can serve as building-block elements towards synthesising the wall-normal structure of a canonical turbulent boundary layer, in the context of large-scale streamwise motions. The rapidly distorted (or “synthetic”) boundary layer presents a simpler environment in which the coherent motions can evolve and therefore can enable a better characterisation of these motions. To further illustrate the utility of the present approach we compare results from our measurements with the predictions of the Rapid Distortion Theory (RDT). We show that the streamwise turbulence energy in the near-wall region of the rapidly distorted boundary layer grows linearly with time consistent with the RDT results on the effect of pure shear on an initially isotropic turbulence. Moreover close to the edge of the boundary layer the large-scale fluctuations experience an enhancement in the streamwise turbulence energy in accordance with the linear blocking model in the RDT framework. The present work thus highlights the importance of linear processes in wall turbulence and can help us identify aspects of it to which the linear theories can be meaningfully applied.     

Large eddy simulations in low-pressure turbines: Effect of wakes at elevated free-stream turbulence

The transition of a separated shear layer over a flat plate, in the presence of periodic wakes and elevated free-stream turbulence (FST), is numerically investigated using Large Eddy Simulation (LES). The upper wall of the test section is inviscid and specifically contoured to impose a streamwise pressure distribution over the flat plate to simulate the suction surface of a low-pressure turbine (LPT) blade. Two different distributions representative of a ‘high-lift’ and an ‘ultra high-lift’ turbine blade are examined. Results obtained from the current LES compare favourably with the extensive experimental data previously obtained for these configurations. The LES results are then used to further investigate the flow physics involved in the transition process.In line with experimental experience, the benefit of wakes and FST obtained by suppressing the separation bubble, is more pronounced in ‘ultra high-lift’ design when compared to the ‘high-lift’ design. Stronger ‘Klebanoff streaks’ are formed in the presence of wakes when compared to the streaks due to FST alone. These streaks promoted much early transition. The weak Klebanoff streaks due to FST continued to trigger transition in between the wake passing cycles.The experimental inference regarding the origin of Klebanoff streaks at the leading edge has been confirmed by the current simulations. While the wake convects at local free-stream velocity, its impression in the boundary layer in the form of streaks convects much slowly. The ‘part-span’ Kelvin–Helmholtz structures, which were observed in the experiments when the wake passes over the separation bubble, are also captured. The non-phase averaged space-time plots manifest that reattachment is a localized process across the span unlike the impression of global reattachment portrayed by phase averaging.     

Simulation of the Effect of the Freestream Turbulence Parameters on the Boundary Layer of a Curvilinear Airfoil

Modified variants of differential turbulence models which make it possible continuously to calculate both the entire flow region with laminar, transition and turbulent regimes and local low Reynolds number zones are proposed for investigating the flow and heat transfer in the boundary layers developing in compressible gas flow past curvilinear airfoils. The effect of the intensity and scale of free-stream turbulence and their variability along the outer boundary layer edge, as well as the combined action of the turbulence intensity and the streamwise pressure gradient in flow past blade profiles, on the heat transfer and near-wall turbulence characteristics is analyzed. The numerical results are compared with experimental and theoretical data.     

Investigation of the vortex induced unsteadiness of a separation bubble via time-resolved and scanning PIV measurements

A transitional separation bubble on the suction side of an SD7003 airfoil is considered. The transition process that forces the separated shear layer to reattach seems to be governed by Kelvin–Helmholtz instabilities. Large scale vortices are formed due to this mechanism at the downstream end of the bubble. These vortices possess a three-dimensional structure and detach from the recirculation region, while other vortices are formed within the bubble. This separation of the vortex is a highly unsteady process, which leads to a bubble flapping. The structure of these vortices and the flapping of the separation bubble due to these vortices are temporally and spatially analyzed at angles of attack from 4° to 8° and chord-length based Reynolds numbers Re _c = 20,000–60,000 using time-resolved PIV measurements in a 2D and a 3D set-up, i.e., stereo-scanning PIV measurements are done in the latter case. These measurements complete former studies at a Reynolds number of Re _c = 20,000. The results of the time-resolved PIV measurements in a single light-sheet show the influence of the angle of attack and the Reynolds number. The characteristic parameters of the separation bubble are analyzed focusing on the unsteadiness of the separation bubble, e.g., the varying size of the main recirculation region, which characterizes the bubble flapping, and the corresponding Strouhal number are investigated. Furthermore, the impact of the freestream turbulence is investigated by juxtaposing the current and former results. The stereo-scanning PIV measurements at Reynolds numbers up to 60,000 elucidate the three-dimensional character of the vortical structures, which evolve at the downstream end of the separation bubble. It is shown that the same typical structures are formed, e.g., the c-shape vortex and the screwdriver vortex at each Reynolds number and angle of attack investigated and the occurrence of these patterns in relation to Λ-structures is discussed. To evidence the impact of the freestream turbulence, these results are compared with findings of former measurements.     

Numerical study on evolution of subharmonic varicose low-speed streaks in turbulent channel flow

The evolution of two spanwise-aligned low-speed streaks in a wall turbulent flow, triggered by the instability of the subharmonic varicose (SV) mode, is studied by a direct numerical simulation (DNS) method in a small spatial-periodic channel. The results show that the SV low-speed streaks are self-sustained at the early stage, and then transform into subharmonic sinuous (SS) low-speed streaks. Initially, the streamwise vortex sheets are formed by shearing, and then evolve into zigzag vortex sheets due to the mutual induction. As the intensification of the SV low-speed streaks becomes prominent, the tilted streamwise vortex tubes and the V-like streamwise vortex tubes can be formed simultaneously by increasing \( + \frac{{\partial u}}{{\partial x}}\). When the SV low-speed streaks break down, new zigzag streamwise vortices will be generated, thus giving birth to the next sustaining cycle of the SV low-speed streaks. When the second breakdown happens, new secondary V-like streamwise vortices instead of zigzag streamwise vortices will be generated. Because of the sweep motion of the fluid induced by the secondary V-like streamwise vortices, each decayed low-speed streak can be divided into two parts, and each part combines with the part of another streak, finally leading to the formation of SS low-speed streaks.     

Effects of free-stream turbulence on a transitional separated–reattached flow over a flat plate with a sharp leading edge

The transitional separated–reattached flow on a flat plate with a blunt leading edge under 2% free-stream turbulence (FST) is numerically simulated using the Large-eddy simulation (LES) approach. The Reynolds number based on the free-stream velocity and the plate thickness is 6500. A dynamic subgrid-scale model is employed and the LES results compare well with the available experimental data.It is well known that FST enhances shear-layer entrainment rates, reduces the mean reattachment distance, and causes early transition to turbulence leading to an early breakdown of the separated boundary layer. Many experimental studies have shown that different vortex shedding frequencies exist, specially the so called low-frequency flapping when there is a separation bubble but its mechanism is still not completely understood. The previous study by us without free-stream turbulence (NFST) did not show the existence of such a low-frequency flapping of the shear layer and it is not clear what the effects of FST will have on these shedding modes. Detailed analysis of the LES data has been presented in the present paper and the low-frequency flapping has not been detected in the current study.     

An experimental study into the effects of streamwise and spanwise acceleration in a turbulent boundary layer

We compare two turbulent boundary layers produced in a low-speed water channel experiment. Both are subjected to an identical streamwise pressure gradient generated via a lateral contraction of the channel, and an additional spanwise pressure gradient is imposed on one of the layers by curving the contraction walls. Despite a relatively high streamwise acceleration, hot-film probe measurements of the mean-velocity distributions show that the Reynolds number increases whilst the coefficient of friction decreases downstream. Visualization of the viscous layers using hydrogen bubbles reveal an increase in the non-dimensional streak spacing in response to the acceleration. Changes in statistical moments of the streamwise velocity near the wall suggest an increased dominance of high-velocity fluctuations. The near-wall streaks and velocity statistics have little sensitivity to the boundary layer three-dimensionality induced by the spanwise pressure gradient, with the boundary-layer crossflow velocity reaching 11 % that of the local freestream velocity.     

Experiments on localized disturbances in a flat plate boundary layer. Part 2. Interaction between localized disturbances and TS-waves

Previous studies on boundary layer transition at moderate levels of free stream turbulence (FST) have shown that the transition process can be promoted by the introduction of Tollmien-Schlichting (TS) waves. In the present work the interaction between localized boundary layer disturbances and controlled TS-waves is studied experimentally. The localized disturbances are generated either from a controlled free stream perturbation, or by means of suction or injection through a slot in the flat plate surface. Both methods result in boundary layer disturbances dominated by elongated streamwise streaks of high and low velocity in the streamwise component. A strong interaction is observed preferably for high frequency TS-waves, which are damped when generated separately, and the interaction starts as a local amplification of a wide band of low-frequency oblique waves. The later stages of the transition process can be identified as a non-linear interaction between the oblique structures, leading to regeneration of new and stronger streamwise streaks.     

Bypass transition receptivity modes

The prediction of bypass transition remains an important problem in many engineering applications. This is largely because there is no suitable theoretical model for bypass transition and predictions are made using empirical models. This paper presents numerical results for the receptivity of a zero pressure gradient boundary layer subjected to simple freestream waveforms which are the constituent parts of a turbulent flow field. Significant receptivities are only obtained for a minority of freestream waveforms and these lead to two types of flow structure in the boundary layer. The first type of flow structure is essentially two dimensional in nature and consists of two rows of counter-rotating spanwise vortices and is induced by freestream waves of large normal and spanwise wavelength and streamwise wavelengths approximately equal to the boundary layer thickness. The second type of flow structure are the streamwise streaks frequently observed in flow visualisation experiments. These streaks are induced by freestream waves of long streamwise and normal wavelength and spanwise wavelengths in the range of 14.5-46 θ (1.7-5.4δ). The freestream waves can be formed of velocity components in any direction, however the boundary layer is most receptive to fluctuations that lie in a plane perpendicular to the streamwise direction. The overall receptivity to a full spectrum of waves typical of freestream turbulence is considered and is shown to have similar characteristics to those from experiments.