Functional Properties and Molecular Degradation of Schizostachyum Brachycladum Bamboo Cellulose Nanofibre in PLA-Chitosan Bionanocomposites

The degradation and mechanical properties of potential polymeric materials used for green manufacturing are significant determinants. In this study, cellulose nanofibre was prepared from Schizostachyum brachycladum bamboo and used as reinforcement in the PLA/chitosan matrix using melt extrusion and compression moulding method. The cellulose nanofibre(CNF) was isolated using supercritical carbon dioxide and high-pressure homogenisation. The isolated CNF was characterised with transmission electron microscopy (TEM), FT-IR, zeta potential and particle size analysis. The mechanical, physical, and degradation properties of the resulting biocomposite were studied with moisture content, density, thickness swelling, tensile, flexural, scanning electron microscopy, thermogravimetry, and biodegradability analysis. The TEM, FT-IR, and particle size results showed successful isolation of cellulose nanofibre using this method. The result showed that the physical, mechanical, and degradation properties of PLA/chitosan/CNF biocomposite were significantly enhanced with cellulose nanofibre. The density, thickness swelling, and moisture content increased with the addition of CNF. Also, tensile strength and modulus; flexural strength and modulus increased; while the elongation reduced. The carbon residue from the thermal degradation and the glass transition temperature of the PLA/chitosan/CNF biocomposite was observed to increase with the addition of CNF. The result showed that the biocomposite has potential for green and sustainable industrial application.     

Crystallization behavior and mechanical properties of poly(lactic acid)/poly(ethylene oxide) blends nucleated by a self-assembly nucleator

Poly(lactic acid) (PLA)/poly(ethylene oxide) (PEO) blends nucleated by a self-assembly nucleating agent, N,N′,N″-tricyclohexyl-1,3,5-benzenetricarboxylamide (BTCA), were prepared by melt blending. The crystallization behavior and mechanical properties of the materials were investigated by differential scanning calorimetry, polarized optical microscopy, wide-angle X-ray diffraction, dynamic mechanical analyzer and tensile testing. It was found that PEO had a synergistic effect together with BTCA on promoting PLA crystallization, besides its toughening effect on the material. Moreover, BTCA revealed prominent reinforcement effect on both neat PLA and PLA/PEO blends in the glass transition region and above, indicating the improvement on the heat resistance of the materials.

     

Cellulose nanofibril (CNF) reinforced starch insulating foams

In this study, biodegradable foams were produced using cellulose nanofibrils (CNFs) and starch (S). The availability of high volumes of CNFs at lower costs is rapidly progressing with advances in pilot-scale and commercial facilities. The foams were produced using a freeze-drying process with CNF/S water suspensions ranging from 1 to 7.5 wt% solids content. Microscopic evaluation showed that the foams have a microcellular structure and that the foam walls are covered with CNF’s. The CNF’s had diameters ranging from 30 to 100 nm. Pore sizes within the foam walls ranged from 20 to 100 nm. The materials’ densities ranging from 0.012 to 0.082 g/cm³ with corresponding porosities between 93.46 and 99.10 %. Thermal conductivity ranged from 0.041 to 0.054 W/m-K. The mechanical performance of the foams produced from the starch control was extremely low and the material was very friable. The addition of CNF’s to starch was required to produce foams, which exhibited structural integrity. The mechanical properties of materials were positively correlated with solids content and CNF/S ratios. The mechanical and thermal properties for the foams produced in this study appear promising for applications such as insulation and packaging.     

3D printed polylactic acid nanocomposite scaffolds for tissue engineering applications

In this study, biodegradable polylactic acid (PLA) and PLA nanocomposite scaffolds reinforced with magnetic and conductive fillers, were processed via fused filament fabrication additive manufacturing and their bioactivity and biodegradation characteristics were examined. Porous 3D architectures with 50% bulk porosity were 3D printed, and their physicochemical properties were evaluated. Thermal analysis confirmed the presence of ~18 wt% of carbon nanostructures (CNF and GNP; nowonwards CNF) and ~37 wt% of magnetic iron oxide (Fe₂O₃) particles in the filaments. The in vitro degradation tests of scaffolds showed porous and fractured struts after 2 and 4 weeks of immersion in DMEM respectively, although a negligible weight loss is observed. Greater extent of degradation is observed in PLA with magnetic fillers followed by PLA with conductive fillers and neat PLA. In vitro bioactivity study of scaffolds indicate enhancement from ~2.9% (PLA) to ~5.32% (PLA/CNF) and ~ 3.12% (PLA/Fe₂O₃). Stiffness calculated from the compression tests showed decrease from ~680 MPa (PLA) to 533 MPa and 425 MPa for PLA/CNF and PLA/Fe₂O₃ respectively. Enhanced bioactivity and faster biodegradation response of PLA nanocomposites with conductive fillers make them a potential candidate for tissue engineering applications such as scaffold bone replacement and regeneration.     

Effects of poly(ethylene glycol) on the morphology and properties of biocomposites based on polylactide and cellulose nanofibers

Polylactide (PLA)/cellulose nanofiber (CNF) biocomposites were prepared via solution casting and direct melt mixing. To improve the compatibility, a masterbatch of CNFs and poly(ethylene glycol) (PEG) (1:2) was also prepared. The effects of PEG on the morphology and properties of the biocomposites were investigated. The dispersion/distribution of nanofibers in PLA was improved when the masterbatch was used and the composites were prepared in solution. Substantial effects on the rheological properties of solution-prepared PLA/CNF/PEG composites were observed compared to composites containing no PEG, whereas for melt-prepared composites no significant changes were detected. Increased crystalline content and crystallization temperature were observed for the composites prepared via the masterbatch and solvent casting. The storage modulus of PLA was increased by 42 and 553% at 25 and at 80 °C, respectively, for the solution-based PEG-compatibilized composite containing 2 wt% nanofibers. Also, a better light transmittance was measured for the PLA/CNF/PEG composites prepared in solution.     

Electrospun hyperbranched polylactic acid–modified cellulose nanocrystals/polylactic acid for shape memory membranes with high mechanical properties

The polylactic acid (PLA) nanofiber membranes reinforced with hyperbranched PLA‐modified cellulose nanocrystals (H‐PLA‐CNCs) were prepared by electrospinning. The H‐PLA‐CNCs and the nanofiber membranes were researched by Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), thermal gravimetric analysis (TGA), differential scanning calorimetry (DSC), and dynamic mechanical analysis (DMA). The outcomes embodied that the cellulose nanocrystals (CNCs) could be successfully improved by the hyperbranched PLA, which would offer powerful CNCs/matrix interfacial adhesion. Thus, the mechanical and shape memory properties of PLA can be improved by adding the H‐PLA‐CNCs. In particular, when the addition of H‐PLA‐CNCs was 7 wt%, the tensile strength and an ultimate strain of PLA composite nanofiber membranes was 15.56 MPa and 25%, which was 228% and 72.4% higher than that of neat PLA, respectively. In addition, the shape recovery rate of the PLA/5 wt% H‐PLA‐CNCs composite nanofiber membrane was 93%, which was 37% higher than that of neat PLA. We expected that this present study would provide unremitting efforts for the development of more effective approaches to prepare biology basic shape memory membranes with high mechanical properties.     

Electrospinning and cutting of ultrafine bioerodible poly(lactide‐co‐ethylene oxide) tri‐ and multiblock copolymer fibers for inhalation applications

Triblock copolymers made up of poly(ethylene oxide) (PEO) and polylactide (PLA) were synthesized and converted to fibers by the electrospinning process. A two‐step in situ‐synthesis in bulk was applied to extend PLA‐PEO‐PLA triblock copolymers with relatively short block length and low molecular weight in order to obtain electrospinnable materials. DL‐lactide was polymerized to the hydroxyl chain ends of PEO via the stannous octoate route. Hexamethylene diisocyanate (HDI) was added as chain extender in the second step, leading to poly(ether‐ester‐urethane) multiblock copolymers. The materials were electrospun from solutions in chloroform. Different concentrations and voltages were analyzed. The ether and ester blocks were varied in their block length and their effects on the fiber morphology was studied. Variations in the electrical conductivity of the chloroform solutions were investigated by adding triethyl benzyl ammonium chloride (TEBAC) in different amounts. Finally, with high quality electrospun PLA‐PEO‐PEO triblock copolymer fibers mechanical cutting was possible. Copyright © 2009 John Wiley & Sons, Ltd.     

Amphiphilic polylactide-poly(ethylene oxide)-poly(propylene oxide) block copolymers: Self-assembly behavior and cell affinity

Polylactide (PLA) is a biodegradable polyester recognized for its potential use as a biomedical material. Poly(ethylene oxide) (PEO) and copolymers based on PEO and poly(propylene oxide) (PPO) are biocompatible polyethers widely applied in the biomedical field, particularly as macromolecular nonionic surfactants. In this work, PLA blocks were attached to the PEO and to the PEO and PPO-based triblock copolymer PEO–PPO–PEO, through ring-opening polymerization of racemic lactide (rac-LA) to obtain the amphiphilic triblock PLA–PEO–PLA and pentablock PLA–PEO–PPO–PEO–PLA copolymers containing hydrophilic/hydrophobic blocks with variable block mass ratios. The copolymers were evaluated for chemical composition, molar mass, and thermal properties, and they were used to prepare self-assemble aggregates in water from tetrahydrofuran polymer solutions. The combination of scattering light experiments and microscopy techniques revealed the spherical morphology of the aggregates with diameters around 180–200 nm, which comprises a hydrophobic PLA core and a hydrophilic polyether shell. The aggregates are nontoxic to human cervical cancer cell line — HeLa cells, as determined by MTS assay, and the aggregates are potential candidates to be applied in the encapsulation of hydrophobic compounds. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 2203–2213     

Supercritical Carbon Dioxide Isolation of Cellulose Nanofibre and Enhancement Properties in Biopolymer Composites

The physical properties, such as the fibre dimension and crystallinity, of cellulose nanofibre (CNF) are significant to its functional reinforcement ability in composites. This study used supercritical carbon dioxide as a fibre bundle defibrillation pretreatment for the isolation of CNF from bamboo, in order to enhance its physical properties. The isolated CNF was characterised through zeta potential, TEM, XRD, and FT-IR analysis. Commercial CNF was used as a reference to evaluate the effectiveness of the method. The physical, mechanical, thermal, and wettability properties of the bamboo and commercial CNF-reinforced PLA/chitin were also analysed. The TEM and FT-IR results showed the successful isolation of CNF from bamboo using this method, with good colloidal stability shown by the zeta potential results. The properties of the isolated bamboo CNF were similar to the commercial type. However, the fibre diameter distribution and the crystallinity index significantly differed between the bamboo and the commercial CNF. The bamboo CNF had a smaller fibre size and a higher crystallinity index than the commercial CNF. The results from the CNF-reinforced biocomposite showed that the physical, mechanical, thermal, and wettability properties were significantly different due to the variations in their fibre sizes and crystallinity indices. The properties of bamboo CNF biocomposites were significantly better than those of commercial CNF biocomposites. This indicates that the physical properties (fibre size and crystallinity) of an isolated CNF significantly affect its reinforcement ability in biocomposites. The physical properties of isolated CNFs are partly dependent on their source and production method, among other factors. These composites can be used for various industrial applications, including packaging.     

不同磺化度下的磺化聚醚醚酮对全钒储能液流电池性质影响的研究

本文报道了采用浓硫酸作为磺化剂,成功合成了不同磺化度下的聚醚醚酮(PEEK)膜,并深入研究了磺化条件包括磺化时间和磺化剂的用量对所获薄膜性能的影响,获得了在不同磺化度（DS）下SPPEK膜的离子交换容,含水率,机械性能,质子电导率等参数,特别测定了在全钒液流电池工作条件下钒离子(Ⅳ)渗透率,首次为该类液流储能电池使用价廉质优的质子交换膜提供了基础实验数据。室温条件下的实验结果如下：1）磺化12小时后,膜的磺化度46%,含水量为28%,钒离子(Ⅳ)选择性最佳（钒离子渗透率为1.2×10-7 cm2/min-1,是Nafion117 (2.9×10-6 cm2/min-1)的1/24）,其质子电导率只有0.02 S/cm;2）磺化96小时其磺化度达79%的膜,质子电导率达0.16 S/cm,是Nafion117 (0.10S/cm) 的1.6倍, 但其机械性能最差;3）与Nafion117膜相比,磺化在36到48小时的SPPEK膜其机械力学性能好,薄膜的钒离子渗透率、离子交换容IEC、质子导电率和含水率高,且对钒离子的选择性佳,尤其价格仅为Nafion膜的1/13,是理想的Nafion膜的代替物,可望直接应用于全钒氧化还原液流（VRB）电池中。本文还讨论了磺化时间和不同磺化剂量对膜的性质的影响。     

Resin impregnation of cellulose nanofibril films facilitated by water swelling

Flexible composite films were produced by impregnating aqueous phenol formaldehyde (PF) resin into water-swollen cellulose nanofibril (CNF) films. CNF films were prepared using a pressurized filtration method in combination with freeze drying. The freeze-dried films were swollen with water then impregnated with PF resin by soaking in aqueous resin solutions of varying concentrations. Small amounts of PF slightly enhanced the tensile properties of CNF films. The formulation with the best mechanical properties was CNF/PF films with 8 wt % resin exhibiting tensile stress and toughness of 248 MPa and 26 MJ/m³, respectively. Resin concentrations higher than about 8 % resulted in composites with decreased tensile properties as compared to neat CNF films. The wet strength of the composite films was significantly higher than that of the neat CNF films. The resulting composites showed greater resistance to moisture absorption accompanied by reduced thickness swelling when soaked in water as compared to neat CNF films. The composites also showed decreased oxygen permeability at low humidity compared to neat films, but the composites did not show improved barrier properties at high humidity.     

Development of biopolymer/cellulose/silica nanostructured hybrid materials and their characterization by NMR relaxometry

The objective of this study was to investigate the preparation and properties of hybrid materials composed of poly(lactic acid) (PLA) and poly(lactic acid)/poly(lactic-co-glycolic acid) (PLA/PLGA) blends employing cellulose nanocrystals (CNCs) and/or organophilic silica (R972) as nanoparticles. The CNCs were obtained by acid hydrolysis of commercially available microcrystalline cellulose (MCC). The materials were produced in film form by solution casting. Organophilic silica was incorporated at a ratio of 3 wt.%, and CNCs were added at ratios of 3 wt.% and 5 wt.% in relation to the weight of the polymer matrix. Two series of films were obtained. The first was prepared using only PLA as the matrix, and the second was obtained using blends of PLA and PLGA. The properties of the films were evaluated by X-ray diffractometry, nuclear magnetic resonance, Fourier-transform infrared spectroscopy and measurement of mechanical properties. The results revealed that each nanoparticle, whether added individually or combined with the other type of nanoparticle, induced different final material properties. Cellulose nanocrystals can act as nucleating agents for the crystallization of PLA. There was an improvement in the mechanical performance of films with the addition of CNCs. Further, the incorporation of silica combined with CNCs resulted in the generation of films with the strongest mechanical properties. The results of this study indicate that silica decreases the surface tension between PLA-cellulose and PLA/PLGA-cellulose.     

Tuning the localization of finely dispersed cellulose nanocrystal in poly (lactic acid)/bio‐polyamide11 blends

A versatile approach to control the localization of cellulose nanocrystal (CNC) in PLA/PA11 blends is presented. A PEO/CNC mixture with a high level of CNC dispersion is prepared through a combination of high pressure homogenization and freeze‐drying. The prepared PEO/CNC mixture is then incorporated into the PLA/PA11 blends using two different strategies. Typically for CNC/PLA/PA11, the CNCs selectively localize in PA11. However, PEO‐coated CNC particles segregate into PLA irrespective of whether the PEO/CNC mixture is premixed with PLA or PA11. It is suggested that a strong interaction between PEO and CNC particles combined with the PLA/PEO miscibility facilitates the localization of PEO‐coated CNC in the PLA. The localization of PEO‐coated CNC in the PLA has no effect on the morphology of the PLA‐5PEO/PA11 with matrix/dispersed phase form. However, 2 wt % PEO‐coated CNC in the co‐continuous (PLA‐5PEO)/PA11 50/50 vol % blend diminishes the phase thickness from 11 ± 1 to 4 ± 1.5 μm. This is attributed to a retarded relaxation of the PLA phase. This work outlines a strategy to control the CNC localization into a given polymeric phase in a binary polymer–polymer mixture. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 576–587     

Efficient barrier properties of mechanically enhanced agro-extracted cellulosic biocomposites

The objective of this work was to prepare the mechanically stable hydrophobic biocomposites by incorporating the cellulose fibers into the polymer matrices for their applications in biomedical and food packaging. Herein, two different types of biocomposites were prepared by mixing polylactic acid (PLA) and polyhydroxybutyrate (PHB) with the agro-extracted cellulose, separately at 170 °C. The influence of the cellulose fibers on the thermal, mechanical, and barrier properties of polymer matrices (PLA and PHB) was observed. With an increase in the cellulose content in PLA and PHB, the tensile strength of the biocomposite materials significantly improved with the enhancement of 24.45% and 32.08%, respectively, compared with the pure PLA and PHB. Furthermore, a decrease of 74.16% and 73.49% in the water vapor transmission rate and oxygen transmission rate, respectively, was observed for cellulose/PHB biocomposites. This study highlights that adding cellulose fibers significantly improves the mechanical and the barrier properties of PLA and PHB, suggesting their biocomposites for use in biodegradable polymer industries.     

Effect of PHB on the properties of biodegradable PLA blends

Blends of biodegradable polymers polylactic acid/thermoplastic starch/polyhydroxybutyrate (PLA/TPS/PHB) were prepared using a twin-screw extruder. The TPS content was constant (50 %) and the PHB content in the blends was gradually changed from 0 mass % to 20 mass %. TPS was prepared by melting, where a mixture of native starch, water and glycerol was fed into the twinscrew extruder. Average temperature of extrusion was 180°C and the concentration of glycerol was 40 mass %. Influence of the PHB concentration in the blend and that of the processing technology on the mechanical and rheological properties of the PLA/PHB composition containing TPS were studied. Mechanical properties were measured 24 h after the film and monofilament preparation and also after the specific storage time to study the effect of storage on the properties. The results indicate that differences in morphology strongly influence the mechanical properties of the studied materials with identical material composition.     

Thermo‐responsive shape memory behavior of poly(styrene‐b‐isoprene‐b‐styrene)/ethylene‐1‐octene copolymer thermoplastic elastomer blends

Thermally‐triggered shape memory polymers (SMPs) are smart materials, which are capable of changing their shapes when they are exposed a heat stimulant. Blending semi‐crystalline and elastomeric polymers is an easy and low‐cost way to obtain thermo‐responsive SMPs. In this work, novel poly(ethylene‐co‐1‐octene) (PEO) and poly(styrene‐b‐isoprene‐b‐styrene) (SIS) thermoplastic elastomer blends were prepared via melt blending method. The morphological, mechanical, rheological properties and shape memory behaviours of the blends were investigated in detail. In morphological analysis, co‐continuous morphology was found for 50 wt% PEO/50 wt% SIS and 60 wt% PEO/40 wt% SIS (60PEO/40SIS) blends. The shape memory analysis performing by dynamic mechanical analyzer showed that the 60PEO/40SIS blend also exhibited the optimum shape memory performance with 95.74% shape fixing and 98.98% shape recovery. Qualitatively shape memory analysis in hot‐water pointed out that the amount of semi‐crystalline PEO promotes shape fixing ability of the blends whereas SIS content enhances shape recovery capability. Although the SIS and PEO are immiscible polymers, the blends of them were exhibited good elastomeric properties with regard to tensile strength, toughness, and elongation at break.     

Moisture Absorption Effects on the Mechanical Properties of Sandwich Biocomposites with Cork Core and Flax/PLA Face Sheets

The aim of this study was to evaluate the moisture absorption behaviour and its influence on the mechanical properties of newly developed sandwich biocomposites with flax fibre-reinforced poly-lactic acid (PLA) face sheets and soft cork as the core material. Three different types of sandwich biocomposite laminates comprised of different layup configurations, namely, non-woven flax/PLA (Sample A), non-woven flax/PLA and cork as core (Sample B) and non-woven flax/paper backing/PLA, cork as core (Sample C), were fabricated. In order to evaluate the influence of moisture ingress on the mechanical properties, the biocomposites were immersed in seawater for a period of 1200 h. The biocomposites (both dry and water immersed) were then subjected to tensile, flexural and low-velocity falling weight impact tests. It was observed from the experimental results that the moisture uptake significantly influenced the mechanical properties of the biocomposites. The presence of the cork and paper in sample C made it more susceptible to water absorption, reaching a value of 34.33%. The presence of cork in the core also has a considerable effect on the mechanical, as well as energy dissipation, behaviours. The results of sample A exhibited improved mechanical performance in both dry and wet conditions compared to samples B and C. Sample A exhibits 32.6% more tensile strength and 81.4% more flexural strength in dry conditions than that in sample C. The scanning electron microscopy (SEM) and X-ray micro-CT images revealed that the failure modes observed are a combination of matrix cracking, core crushing and face core debonding. The results from this study suggest that flax/PLA sandwich biocomposites can be used in various lightweight applications with improved environmental benefits.     

填充型具有微孔结构的磺化聚芳醚砜/聚醚砜复合质子交换膜的制备及性能

制备了基于磺化聚芳醚砜(SPAES)及聚醚砜(PES)的填充型复合质子交换膜, 研究了其吸水率、 尺寸变化、 热-机械特性、 质子电导率、 甲醇透过性及稳定性等性能. 通过浸入沉淀相转化法, 采用磺化度分别为30%(S30), 40%(S40)及50%(S50)的SPAES与PES制备了系列微孔型复合质子交换膜 Sx-y(x为SPAES的磺化度, y为SPAES的质量分数); 然后利用真空抽滤法在微孔中填充S50制备了相应的填充型复合质子交换膜Sx-y+F50. 结果表明, 由于微孔的引入及皮层结构的存在, Sx-y膜在低离子交换容量(IEC)条件下仍具有较高的电导率、 优良的机械强度、 优异的化学稳定性及较低的甲醇透过性. 经S50填充后, Sx-y+F50膜的IEC及电导率明显提升, 甲醇透过率大幅下降, 但机械强度及化学稳定性未见劣化. 其中S30-40+F50膜(IEC=0.69 mmol/g)的综合性能最佳, 其质子电导率在90 ℃水中达到50.4 mS/cm; 经140 ℃水处理24 h后失重率仅为8.2%, 质子电导率降低仅9%; 经过芬顿试剂(3% H₂O₂, 20 mg/L FeSO₄, 80 ℃, 1 h)处理后失重率仅为0.66%; 甲醇透过率仅为6.8×10^-8 cm²/s.     

Hydrogel networks of poly(ethylene oxide) star-molecules supported by expanded polytetrafluoroethylene membranes: characterization, biocompatibility evaluation and glucose diffusion characteristics

The present work discusses the grafting by electron beam irradiation of poly(ethylene oxide) (PEO) star-shaped polymers onto porous expanded polytetrafluoroethylene (EXPTFE) surfaces. The resulting materials are intended to combine the good biocompatible properties of PEO with the outstanding mechanical properties of PTFE. The star-shaped PEOs were synthesized via anionic polymerization. 3 Mev electron beam irradiation was applied to graft these PEO stars onto porous EXPTFE surfaces. The hydrophobic EXPTFE surface had to be pre-modified with N-vinylpyrrolidone. ESCA was used to quantify the amount of grafted star-shaped PEO. Unmodified EXPTFE surfaces are well known, when implanted in a body, to be rapidly covered by a layer of cells and fibrin. The EXPTFE coated with PEO were implanted in the peritoneal cavity of rats (or under the back skin). This implantation did not induce any inflammation reactions and SEM analysis had attested the absence of adsorbed cells and fibrin. The glucose diffusion properties of these membranes were studied by a lag time analysis method and compared to those of pure PEO hydrogels. As expected, glucose diffuses through the hydrogel coated membrane and diffusion is not affected by the presence of the EXPTFE membrane.