首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 859 毫秒
1.
To develop a novel tissue engineering scaffold with the capability of controlled releasing BMP-2-derived synthetic peptide, porous poly(lactic acid)/chitosan microspheres (PLA/CMs) composites containing different quantities of chitosan microspheres were prepared by a thermally induced phase separation method. FTIR analysis revealed that there were strong hydrogen bond interactions between the PLA and chitosan component. Introduction of less than 30% CMs (on PLA weight basis) did not remarkably affect the morphology and porosity of the PLA/CMs scaffolds. The compressive strength of the composite scaffolds increased from 0.48 to 0.66 MPa, while the compressive modulus increased from 7.29 to 8.23 MPa as the microspheres' contents increased from 0% to 50%. In vitro degradability investigation indicated that the dissolution of chitosan component was preferential than PLA matrix and the inclusion of CMs could neutralize the acidity of PLA degradation products. Compared with the rapid release from CMs, the synthetic peptide was released from PLA/CMs scaffolds in a temporally controlled manner, mainly depending on the degradation of PLA matrix. The promising microspheres based scaffold release system can be used to deliver bioactive factors for a variety of non-loaded bone regeneration and tissue engineering application.  相似文献   

2.
利用真空冷冻干燥技术, 将不同质量的纳米硅酸镁锂(nLMS)与壳聚糖(CA)和海藻酸钠(SA)混合, 制备了纳米硅酸镁锂-壳聚糖-海藻酸钠(nLMS-CS-SA)复合支架材料. 研究了不同质量分数(1%, 2%, 3%, 4%)的nLMS对nLMS-CS-SA复合支架材料的外形、 微观形貌、 溶胀率、 孔隙率、 体外降解性能和生物相容性的影响, 以确定nLMS-CS-SA复合支架材料中最佳nLMS含量. 研究结果显示, nLMS-CS-SA复合支架材料是具备形态可塑性的多孔状固体, 各组材料纵断面呈片层状, 其结构疏松且内部孔隙具有高度连通性; 随着nLMS含量的增加, nLMS-CS-SA复合支架材料的孔隙率呈现先降后升的趋势; 当nLMS的质量分数为3%时, 其溶胀比最小, 体外降解速率最慢; nLMS的添加降低了nLMS-CS-SA复合支架材料的毒性. 因此, nLMS在nLMS-CS-SA复合支架材料中的最佳含量为3%.  相似文献   

3.
Due to their potential renewable materials-based tissue engineering scaffolds has gained more attention. Therefore, researchers are looking for new materials to be used as a scaffold. In this study, we have focused on the development of a nanocomposite scaffold for bone tissue engineering (using bacterial cellulose (BC) and β-glucan (β-G)) via free radical polymerization and freeze-drying technique. Hydroxyapatite nanoparticles (n-HAp) and graphene oxide (GO) were added as reinforcement materials. The structural changes, surface morphology, porosity, and mechanical properties were investigated through spectroscopic and analytical techniques like Fourier transformation infrared (FT-IR), scanning electron microscope (SEM), Brunauer–Emmett-Teller (BET), and universal testing machine Instron. The scaffolds showed remarkable stability, aqueous degradation, spongy morphology, porosity, and mechanical properties. Antibacterial activities were performed against gram -ive and gram + ive bacterial strains. The BgC-1.4 scaffold was found more antibacterial compared to BgC-1.3, BgC-1.2, and BgC-1.1. The cell culture and cytotoxicity were evaluated using the MC3T3-E1 cell line. More cell growth was observed onto BgC-1.4 due to its uniform interrelated pores distribution, surface roughness, better mechanical properties, considerable biochemical affinity towards cell adhesion, proliferation, and biocompatibility. These nanocomposite scaffolds can be potential biomaterials for fractured bones in orthopedic tissue engineering.  相似文献   

4.
朱丹 《高分子科学》2014,32(4):497-508
Composite biomaterials made of biodegradable polylactic acid (PLA) and bioactive magnesium (Mg) salt are developed for orthopaedic implants or metal implant coatings. The releasing of Mg salt into the biological environment benefits the bone growth, while with the releasing of Mg salt and degradation of PLA there forms a porous scaffold for tissue engineering. The size and morphology of the salt and voids are adjustable with such preparation conditions as salt content, pH of casting solution, and the solidification rate, so that we can control the salt releasing and degradation rate of PLA. Dielectric spectroscopy is used to investigate the dispersive structures of Mg salt and voids in the polymer matrix and to monitor the in situ releasing of Mg salts in the simulated body fluid (SBF). The current study provides us with an orthopedic biomaterial with controllable multi-phase structures, and a tool to investigate the in vivo behaviors of biomaterials.  相似文献   

5.
利用海藻酸钠和壳聚糖2种原料, 采用阴阳离子静电复合原理, 通过滴注法层层自组装成可搭载药物的缓释微球, 再按一定比例与海藻酸钠-壳聚糖溶液混合制成缓释微球型支架材料, 将缓释微球结构嵌入疏松多孔海绵状结构中. 研究了缓释微球的组分比对缓释微球型支架材料的孔隙率、 收缩率、 亲水性及降解性能的影响; 扫描电子显微镜照片显示, 微球结构相对完整, 多孔海绵状结构孔径为140~200 μm; 支架浸出液细胞毒性检测实验组对照组未见差异. 缓释微球体积所占比例即组分比为10%的缓释微球型支架材料孔隙率最高为68.2%~70.8%, 亲水性最好, 收缩率最低为4.4%~5.2%; 支架降解速率随缓释微球组分比升高而减慢, 组分比为20%的缓释微球型支架材料综合性能更优; 缓释微球型支架材料冻干成型前为液态, 具有良好可塑性. 缓释微球型支架材料为缓释系统与多孔支架材料有机结合提供了新思路.  相似文献   

6.
Porous scaffolds based on water-soluble PLGA and CS were prepared. The pores were verified to be alveolate, uniform and continuous. The effects of freezing temperature, freeze-drying time, solid content and molecular weight of reactants on the pore structure of the scaffolds were studied. The scaffold morphology could be adjusted by changing the freezing temperature and solid content of reacting polymer. Their degradation rate can be adjusted by changing the proportion of PLGA and CS. The porosity of scaffolds was higher than 90% and the high swelling ratio showed that these scaffolds had excellent hydrophilic performance. The in vitro culture of chondrocytes indicates that the obtained PLGA/CS porous scaffolds are very promising biomaterials for tissue engineering applications.  相似文献   

7.
Summary: Monte Carlo method was used to simulate the degradation of porous PLA scaffolds. The simulated volume was assumed to be divided homogeneously between the pore and solid PLA with the ratio equal to the bulk porosity of the scaffold. The volume was divided into surface and bulk elements where the surface elements were in direct contact with the aqueous degradation medium, while the bulk elements were surrounded by the pore and solid PLA. The effect of degradation time on PLA ester groups and carboxylic acid end‐groups for surface and bulk elements, pH, PLA degradation rate and mass loss, and PLA molecular weight distribution was simulated. For surface elements, pH remained constant at 7.4 over the entire time of degradation, while for bulk elements its value decreased significantly to as low as 5.8. The highest drop in pH within the scaffold was observed for the highest porosity of 90%. There was a lag time of at least 7 weeks in the mass loss for surface as well as bulk elements for porosities ranging from 70 to 90%. The mass loss for bulk elements was considerably faster than the surface elements. This difference in the rate of mass loss between the surface and bulk elements could affect the 3D morphology and dimensional stability of the scaffold in vivo as degradation proceeds. The simulation predicts that, due to differences in the rate of bulk and surface degradation, hollow structures could form inside the scaffold after 19, 17, and 15 weeks for initial porosities of 70, 80, and 90%, respectively.

A schematic diagram illustrating the degradation of an element on the outer surface of the scaffold (surface element) versus an element within the volume of the scaffold (bulk element).  相似文献   


8.
In this study, biodegradable polylactic acid (PLA) and PLA nanocomposite scaffolds reinforced with magnetic and conductive fillers, were processed via fused filament fabrication additive manufacturing and their bioactivity and biodegradation characteristics were examined. Porous 3D architectures with 50% bulk porosity were 3D printed, and their physicochemical properties were evaluated. Thermal analysis confirmed the presence of ~18 wt% of carbon nanostructures (CNF and GNP; nowonwards CNF) and ~37 wt% of magnetic iron oxide (Fe2O3) particles in the filaments. The in vitro degradation tests of scaffolds showed porous and fractured struts after 2 and 4 weeks of immersion in DMEM respectively, although a negligible weight loss is observed. Greater extent of degradation is observed in PLA with magnetic fillers followed by PLA with conductive fillers and neat PLA. In vitro bioactivity study of scaffolds indicate enhancement from ~2.9% (PLA) to ~5.32% (PLA/CNF) and ~ 3.12% (PLA/Fe2O3). Stiffness calculated from the compression tests showed decrease from ~680 MPa (PLA) to 533 MPa and 425 MPa for PLA/CNF and PLA/Fe2O3 respectively. Enhanced bioactivity and faster biodegradation response of PLA nanocomposites with conductive fillers make them a potential candidate for tissue engineering applications such as scaffold bone replacement and regeneration.  相似文献   

9.
The material surface must be considered in the design of scaffolds for bone tissue engineering so that it supports bone cells adhesion, proliferation and differentiation. A biomimetic approach has been developed as a 3D surface modification technique to grow partially carbonated hydroxyapatite (the bonelike mineral) in prefabricated, porous, polymer scaffolds using a simulated body fluid in our lab. For the rational design of scaffolding materials and optimization of the biomimetic process, this work focused on various materials and processing parameters in relation to apatite formation on 3D polymer scaffolds. The apatite nucleation and growth in the internal pores of poly(L-lactide) and poly(D,L-lactide) scaffolds were significantly faster than in those of poly(lactide-co-glycolide) scaffolds in simulated body fluids. The apatite distribution was significantly more uniform in the poly(L-lactide) scaffolds than in the poly(lactide-co-glycolide) scaffolds. After incubation in a simulated body fluid for 30 d, the mass of poly(L-lactide) scaffolds increased approximately 40%, whereas the mass of the poly(lactide-co-glycolide) scaffolds increased by about 15% (see Figure). A higher ionic concentration and higher pH value of the simulated body fluid enhanced apatite formation. The effects of surface functional groups on apatite nucleation and growth were found to be more complex in 3D scaffolds than on 2D films. Surprisingly enough, it was found that carboxyl groups significantly reduced the apatite formation, especially on the internal pore surfaces of 3D scaffolds. These findings are critically important in the rational selection of materials and surface design of 3D scaffolds for mineralized tissue engineering and may contribute to the understanding of biomineralization as well.SEM micrograph of a poly(L-lactide) scaffold.  相似文献   

10.
Porous poly(l-lactic acid)/β-tricalcium phosphate (PLLA/β-TCP) composite is a new promising scaffold for bone tissue engineering. Porous scaffolds fabricated by liquid anti-solvent precipitation principle were subjected to degradation in dynamic simulated body fluid (DSBF) and in static simulated body fluid (SSBF) at 37 °C for 24 weeks, respectively. Results indicated that a large number of apatite layer were formed on the scaffolds. The results further indicated that SBF flow decreased the degradation rate of molecular weight and compressive strength significantly. The porosity and mass changes were related to the apatite formation and SBF flow. All the results might be owed to the mutual effects of the flow of SBF and the addition of β-TCP. The degradation rate of scaffolds could be adjusted by the additional fraction of β-TCP to meet the requirements of application in vivo.  相似文献   

11.
张舵  章培标 《高分子科学》2011,29(2):215-244
Biodegradable porous nanocomposite scaffolds of poly(lactide-co-glycolide)(PLGA) and L-lactic acid(LAc) oligomer surface-grafted hydroxyapatite nanoparticles(op-HA) with a honeycomb monolith structure were fabricated with the single-phase solution freeze-drying method.The effects of different freezing temperatures on the properties of the scaffolds,such as microstructures,compressive strength,cell penetration and cell proliferation were studied.The highly porous and well interconnected scaffolds with a tunable pore structure were obtained.The effect of different freezing temperature(4℃,-20℃,-80℃and -196℃) was investigated in relation to the scaffold morphology,the porosity varied from 91.2%to 83.0%and the average pore diameter varied from(167.2±62.6)μm to(11.9±4.2)μm while theσ10 increased significantly.The cell proliferation were decreased and associated with the above-mentioned properties.Uniform distribution of op-HA particles and homogeneous roughness of pore wall surfaces were found in the 4℃frozen scaffold.The 4℃frozen scaffold exhibited better cell penetration and increased cell proliferation because of its larger pore size,higher porosity and interconnection.The microstructures described here provide a new approach for the design and fabrication of op-HA/PLGA based scaffold materials with potentially broad applicability for replacement of bone defects.  相似文献   

12.
In this study both collagen and glycosaminoglycans were isolated from biodegradable waste. Namely collagen was isolated from rat tail tendons and glycosaminoglycans (GAGs) from fish skin. Porous materials were then obtained based on the isolated collagen with 1 or 5% addition of GAGs by freeze-drying process. The scaffolds were studied by infrared spectroscopy, mechanical testing and examined for the porosity and density. The scaffolds structure was observed by scanning electron microscope. The adhesion and proliferation of human osteosarcoma SaOS-2 cells was examined on prepared scaffolds to assess their biocompability.The results showed that the addition of glycosaminoglycans improves the properties of collagen-based scaffolds. Mechanical strength was increased by GAGs addition as well as the porosity of studied materials. Each scaffold with and without GAGs displayed porous structure with interconnected regular shaped pores. The attachment of cells was better for pure collagen scaffold, however, GAGs additive promoted the cells proliferation on the scaffold.  相似文献   

13.
Abdominal wall defects are a frequently occurring condition in surgical practice. The most important are material structure and biocompatibility. In this study, polylactic acid (PLA) mesh composited with a 3D printing of acellular dermal matrix (ADM) material is used to repair abdominal wall defects. The results show that the adhesion score of ADM/PLA composite scaffolds is smaller than PLA meshes. Immunohistochemical assessment reveals that the ADM/PLA composite scaffold can effectively reduce the inflammatory response at the contact surface between the meshes and the abdominal organs. And the ADM/PLA composite scaffold can effectively reduce the expression levels of the inflammation-related factors IL-6 and IL-10. In addition, the ADM/PLA composite scaffold repair is rich in the expression levels of tissue regeneration-related factors vascular endothelial growth factor and transforming growth factor β. Thus, ADM/PLA composite scaffolds can effectively reduce surrounding inflammation to effectively promote the repair of abdominal wall defects.  相似文献   

14.
A new class of polylactic acid (PLA)/polyethylene glycol (PEG) copolymer reinforced with bacterial cellulose nanofibers (BC) was prepared using a solvent casting and particulate leaching methods. Four weight fractions of BC (1, 2.5, 5, and 10 wt%) were incorporated into copolymer via silane coupling agent. Mechanical properties were evaluated using response surface method (RSM) to optimize the impact of pore size, porosity, and BC contents. Compressive strength obtained for PLA/PEG-5 BC wt% was 9.8 MPa, which significantly dropped after developing a porous structure to 4.9 MPa. Nielson model was applied to investigate the BC stress concentration on the PLA/PEG. Likewise, krenche and Hapli-Tasi model were employed to investigate the BC nanofiber reinforcement and BC orientation into PLA/PEG chains. The optimal parameters of the experiment results found to be 5 wt% for BC, 230 μm for pore size, and 80% for porosity. Scanning electron microscopy (SEM) micrograph indicates that uniform pore size and regular pore shape were achieved after an addition of BC-5% into PLA/PEG. The weight loss of copolymer-BC with scaffolds enhanced to the double values, compared with PLA/PEG-BC % without scaffolds. Differential Scanning Calorimetric (DSC) results revealed that the BC nanofiber improved glass transition temperature (Tg) 57 °C, melting temperature (Tm) 171 °C, and crystallinity (χ %) 43% of PLA/PEG reinforced-BC-5%.  相似文献   

15.
In this study, in situ synthesis of polyvinyl alcohol (PVA)/nano-hydroxyapatite (n-HA)/cellulose nanocrystals (CNC) organic–inorganic biocomposite porous scaffolds is reported. The effect of the CNC content on the properties of the biocomposite scaffold was investigated and characterized using field-emission scanning electron microscopy, Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD) analysis, porosity and compressive strength measurements, thermal studies, and in vitro biomineralization and degradation studies. The morphological study showed highly porous structures with good pore interconnectivity in which n-HA was homogeneously dispersed. XRD analysis showed a decrease in the crystalline fraction and crystallite size of nano-hydroxyapatite with introduction of PVA and with increasing content of CNC. It was observed that the porosity decreased to some extent with increasing CNC content, while increases in the compressive strength (from 0.85 to 2.09 MPa) and elastic modulus (from 4.68 to 16.01 MPa) were found as the CNC content was increased. In vitro biomineralization study revealed the formation of apatite on PVA/n-HA/CNC biocomposite scaffolds when soaked for 7 and 14 days in simulated body fluid (SBF) solution. The obtained porous scaffolds offering good mechanical performance may provide a promising alternative scaffolding matrix for use in the field of bone tissue engineering.  相似文献   

16.
To investigate the contribution of fibre arrangement to guiding the aligned growth of corneal stroma cells, aligned and randomly oriented fibrous scaffolds of gelatin and poly-L-lactic acid(PLLA) were fabricated by electrospinning. A comparative study of two different systems with corneal stroma cells on randomly organized and aligned fibres were conducted. The efficiency of the scaffolds for inducing the aligned growth of cells was assessed by morphological observation and 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyl-tetrazolium bromide(MTT) assay. Results show that the cells cultured on both randomly oriented and aligned scaffolds maintained normal morphology and well spreading as well as long term proliferation. Importantly, corneal stroma cells grew high orderly on the aligned sca- ffold, while the cells grew disordered on the randomly oriented scaffold. Moreover, the cells exhibited higher viability in aligned scaffold than that in randomly oriented scaffold. These results indcate that electrospinng to prepare aligned fibrous scaffolds has provided an effective approach to the aligned growth of corneal stroma cells in vitro. Our findings that fiber arrangement plays a crucial role in guiding the aligned growth of cells may be helpful to the development of better biomaterials for tissue engineered cornea.  相似文献   

17.
This paper presents a method for the preparation of porous poly(L-lactide)/poly[(L-lactide)-co-glycolide] scaffolds for tissue engineering. Scaffolds were prepared by a mold pressing-salt leaching technique from structured microparticles. The total porosity was in the range 70-85%. The pore size distribution was bimodal. Large pores, susceptible for osteoblasts growth and proliferation had the dimensions 50-400 microm. Small pores, dedicated to the diffusion of nutrients or/and metabolites of bone forming cells, as well as the products of hydrolysis of polyesters from the walls of the scaffold, had sizes in the range 2 nm-5 microm. The scaffolds had good mechanical strength (compressive modulus equal to 41 MPa and a strength of 1.64 MPa for 74% porosity). Scaffolds were tested in vitro with human osteoblast-like cells (MG-63). It was found that the viability of cells seeded within the scaffolds obtained using the mold pressing-salt leaching technique from structured microparticles was better when compared to cells cultured in scaffolds obtained by traditional methods. After 34 d of culture, cells within the tested scaffolds were organized in a tissue-like structure. Photos of section of macro- and mesoporous PLLA/PLGA scaffold containing 50 wt.-% of PLGA microspheres after 34 d of culture. Dark spots mark MG-63 cells, white areas belong to the scaffold. The specimen was stained with haematoxylin/eosin. Bar = 100 microm.  相似文献   

18.
Degradation is among the most important properties of biomaterial scaffolds, which are indispensable for regenerative medicine. The currently used method relies on the measurement of mass loss across different samples and cannot track the degradation of an individual scaffold in situ. Here we report, for the first time, the use of multiscale photoacoustic microscopy to non‐invasively monitor the degradation of an individual scaffold. We could observe alterations to the morphology and structure of a scaffold at high spatial resolution and deep penetration, and more significantly, quantify the degradation of an individual scaffold as a function of time, both in vitro and in vivo. In addition, the remodeling of vasculature inside a scaffold can be visualized simultaneously using a dual‐wavelength scanning mode in a label‐free manner. This optoacoustic method can be used to monitor the degradation of individual scaffolds, offering a new approach to non‐invasively analyze and quantify biomaterial–tissue interactions in conjunction with the assessment of in vivo vascular parameters.  相似文献   

19.
Abstract

In this paper, a series of porous nanohydroxyapatite/silk fibroin/chitosan (nHA/SF/CTS) scaffolds were successfully prepared using the freeze-drying method. The biomaterials were characterized by attenuated total reflection Fourier transform infrared spectroscopy, and mechanical testing and thermogravimetric analysis. Moreover, studies of porosity, pore size, swelling properties and in vitro degradation test were performed. Research has proved that micro-structure, porosity, water adsorption and compressive strength were greatly affected by the components’ concentration, in particular the content of silk fibroin. SEM observations showed that the scaffolds of nHA/SF/CTS are highly porous, with pore size in wide range from 25 to 300?µm which is suitable for cell growth. nHA/SF/CTS scaffolds have sufficient mechanical integrity to resist handling during implantation and in vivo loading. Both, the compressive modulus and compressive strength of the scaffold, decrease with the increase in silk fibroin content.  相似文献   

20.
Inverted colloidal crystals as three-dimensional cell scaffolds   总被引:1,自引:0,他引:1  
A new type of three-dimensional scaffold with inverted colloidal crystal geometry for the investigation of topological effects in cell cultures is introduced in this publication. The scaffolds are made by infiltration of the hexagonal crystal lattice of polystyrene spheres with sol-gel formulation and subsequent annealing. It possesses a relatively high degree of order among existing cell scaffolds and affords tight control over the scaffold porosity and tissue organization. The prepared scaffolds can be a convenient system for the investigation of cell-cell and cell-matrix interactions. Their biocompatibility is demonstrated for human hepatocellular carcinoma HEP G2 and human bone marrow HS-5 cell cultures. A preliminary effect of the scaffold topology on cell proliferation is observed. HEP G2 hepatocytes form a large number of 10-15 cell colonies on scaffolds made from 75-microm spheres, while their number diminishes for scaffolds from 10- and 160-microm spheres. Under similar conditions, HS-5 forms smaller colonies consisting of three to four cells in 90-microm cavities.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号