Changes of mechanical properties in cold-crystallized syndiotactic polypropylene during aging

Many semicrystalline polymers undergo a process of aging when they are stored at temperatures higher than their glass-transition temperature (T _g). Syndiotactic polypropylene was quenched from the melt to −40 °C, crystallized from the glassy state at 20 or 40 °C and stored at the respective temperature for different aging times up to 7200 h. A significant increase in the tensile modulus and stress at yield and a decrease in strain at yield were observed for both aging temperatures. Differential scanning calorimetry (DSC) scans of aged material showed an endothermic annealing peak 15–30 °C above the previous aging temperature, the maximum temperature and enthalpic content of which increased with aging time. The position and the shape of the melting peak were not affected by aging. Scans of the storage modulus obtained from dynamic mechanical analyser measurements indicated a softening process starting at about 20 °C above the aging temperature and correlating with the annealing peak detected by DSC. Density measurements and wide-angle X-ray scattering investigations revealed that neither the crystallinity increased significantly nor did the crystal structure change. So the observed property changes induced by aging are attributed to microstructural changes within the amorphous phase. Furthermore, it could be shown by annealing experiments carried out at 60 °C, that aging above T _g is, analogous to aging below T _g (physical aging), a thermoreversible process. Received: 18 September 2000 Accepted: 2 January 2001     

Research on mechanical and dielectric properties of XLPE cable under accelerated electrical‐thermal aging

Research into the electrical‐thermal aging properties of cross‐linked polyethylene (XLPE) cable has great significance, because of its wide application. This study conducted accelerated electrical‐thermal aging tests on 10‐kV XLPE cable in order to assess the cable's mechanical and dielectric properties. After being aged by applying 34.8‐kV AC voltage at the four temperatures of 90, 103, 114, and 135°C, the cable samples were taken out in five stages according to the aging time and cut into slices. The slices were conducted experiments to test the breaking elongation, tensile strength, gel content, breakdown voltage, and frequency spectrums of the dielectric constant and dielectric loss. The results demonstrate that the mechanical strength and gel content of XLPE vary greatly under different aging temperatures, a finding that is associated with the crystallization characteristics of the material. The breakdown voltage shows a slight decreasing trend with aging time. The dielectric constant decreases with aging time in high‐frequency areas (10³–10⁶ Hz), while the dielectric loss factor increases with aging time at low frequencies (10^?2–0 Hz). These two parameters can be used to characterize the degree of aging in cable. Copyright © 2016 John Wiley & Sons, Ltd.     

Changes in cellulose supramolecular structure and molecular weight distribution during steam explosion of aspen wood

We have studied the cellulose supramolecular structure in pulps obtainedby steam explosion of aspen wood. The pulps were bleached with hydrogenperoxidein an OQP-sequence and characterised by size exclusion chromatography and¹³C cross polarisation magic angle spinning (CP/MAS)NMR-spectroscopy. With CP/MAS-NMR-spectroscopy and chemometrics we were able toseparate the supramolecular structural changes taking place during steamexplosion into two independent processes. One process was related to the extentof processing and showed degradation and dissolution of cellulose,hemicelluloseand lignin accompanied by an increase in cellulose content. The second processwas displayed by pulps having molecular weights below approximately 100000 andwas interpreted as showing the removal of dislocations and an increase incrystalline and/or paracrystalline cellulose in the cellulose fibrils.     

Effect of alkali and ultraviolet aging on physical,thermal, and mechanical properties of fibers for potential use as reinforcing elements in glass/silicate composites

This work reports the effect of an alkaline environment and ultraviolet (UV) radiation on the physical, thermal, and tensile properties of different fibers selected as potential reinforcing elements to enhance the impact properties of brittle glass/silicate composites. The fibers, which included regenerated cellulosic (viscose and rayon), synthetic (ultrahigh molecular weight polyethylene, polypropylene, polyamide, acrylic), glass, ceramic, and steel, were aged in different alkaline solutions with pH ranging from 11.1 to 13.6 at 70°C for different periods of time and exposed to UV radiation for 330 h. The physical and thermal properties of aged fibers were studied using tensile testing, scanning electron microscopy, and simultaneous differential and thermogravimetric analysis. Results showed that the regenerated cellulosic fibers, acrylic, E‐glass, and A‐glass fibers could not withstand the highly alkaline environment. Overall, ultrahigh molecular weight polyethylene, UV‐stable polypropylene, polyamide 6.6, AR‐glass, ceramic (alumino borosilicate), and steel fibers performed very well under all conditions, indicating that they have the potential to be used as reinforcing elements in glass/silicate composites. Copyright © 2011 John Wiley & Sons, Ltd.     

Changes in superstructure and mechanical properties of poly(ethylene‐2,6‐naphthalate) fibers with critical necking tension

Poly(ethylene‐2,6‐naphthalate) fibers were zone‐drawn under a critical necking tension (σ_c) defined as the minimum tension needed to generate a necking at a given drawing temperature (T_d). In the zone drawing under σ_c, the neck was observed from 110 to 160 °C. The superstructure in a neck zone induced at each T_d was studied. The σ_c value decreased exponentially with increasing T_d and dropped to a low level at a higher T_d. The draw ratio increased rapidly with T_d increasing above 90 °C, but the birefringence and degree of crystallinity decreased gradually. To study the molecular orientation in the neck zone, we measured a dichroic ratio (A_‖/A_?) of a C? O band at 1256 cm^?1 along a drawing direction in the neck zone with a Fourier transform infrared microscope. A_‖/A_? at T_d = 110 °C increased rapidly in the narrow neck zone, and that at T_d = 140 °C increased in the edge of the wide neck zone. Wide‐angle X‐ray diffraction patterns of the fibers obtained at T_d = 130 °C and lower showed three reflections due to an α form, but those at T_d = 140 and 150 °C had reflections due to the α form and a β form. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1629–1637, 2001     

Load and depth sensing indentation as a tool to monitor a gradient in the mechanical properties across a polymer coating: A study of physical and chemical aging effects

Load and depth sensing indentation has been used to characterize the elastic modulus and hardness of various polycarbonate films. This analytical technique is shown to be extremely suitable for the determination of gradients in these mechanical properties. Furthermore, it is demonstrated that such a gradient exists over a length of micrometers in chemically aged polycarbonate, but it is virtually absent in physically aged polycarbonate. From these results, it is concluded that, although the first 100 nm cannot be probed, physical aging occurs homogeneously throughout the bulk of the sample. However, chemical aging starts at the surface and moves progressively into the bulk of the material. From the study of these films, it appears that for the interpretation of these measurements, knowledge about the amount of creep occurring during the measurements and about the mechanical properties of the substrate on which these films are applied is needed. Creep can be measured with the same indenter through the application of a constant load for a period of time. Load and depth sensing indentation appears to be a powerful method for studying the physical and chemical aging of polymers. It is especially valuable for coatings and films for which conventional tensile testing is problematic. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1628–1639, 2004