Effect of Layering Pattern on the Mechanical Properties of Bark Cloth (Ficus natalensis) Epoxy Composites

The quest for sustainable materials as a consequence of a global drive to mitigate climate change has led to a focus on natural fiber–reinforced composite materials. In this study, skillful ply angle arrangement of bark cloth–reinforced laminar epoxy composites was carried out for the first time using vacuum-assisted resin transfer molding, and the composites fabricated were characterized for the effect of the layering pattern on their static and dynamic mechanical properties. Tensile strength and flexural strength were shown to be dependent on the ply angle arrangement. Dynamic mechanical analysis of the composites showed a glass transition temperature of 70°C, and the storage modulus and mechanical damping properties showed that the developed composites can withstand considerable loads and have excellent fiber-to-matrix adhesion.     

Impact of surface adaptation and Acacia nilotica biofiller on static and dynamic properties of sisal fiber composite

Nowadays, the awareness of the public along with strict legitimate forces over the use of polymers, the manufacturing and automotive industries started using the renewable materials. Since, natural fiber reinforced composites play vital role in developing lightweight structural materials, this study focuses on utilizing sisal fiber as reinforcement in polyester matrix along with natural filler. The influence of fiber length and fiber volume fraction on the mechanical properties of sisal fiber was studied initially. Test results revealed that the composite with 20?mm fiber length and 20-volume fraction composite has better mechanical properties. Furthermore, the effect of fiber surface modification has been analyzed using various chemical solutions such as NaOH, KMnO₄, stearic acid, and maleic acid. Of these, NaOH treatment enhances the mechanical properties of composite compared to all other cases. Finally, the influence of Acacia nilotica, a natural filler addition into the alkali-treated sisal fiber composite has been evaluated by mechanical and dynamic mechanical properties. It is found that the addition of natural filler and surface treatment has enhanced the properties of composites due to their synergetic effect. This effect improves the adhesion and uniform stress transfer among the reinforcements. The fiber surface morphology was evaluated using micrographs obtained from scanning electron microscope.     

The surface modification of carbon fiber for thermoplastic HDPE composites

The interfacial adhesion strength between the fiber and the matrix greatly affects the properties of the carbon fiber (CF)–reinforced composite. The presence of surface functional groups on the fiber and changes in surface roughness were determined by X-ray photoelectron spectroscopy, scanning electron microscopy (SEM), and Raman spectroscopy. The effect of surface modification of CF on the mechanical properties and tribological properties of the composites is enhanced. The performance has been significantly improved. SEM analysis showed that modification had a positive effect on the interface between fiber and matrix. In the paper, the method of CF modification and the treatment of enhanced high-density polyethylene have simple and effective characteristics, which can be widely used and have guiding significance for industrial production.     

The effect of surface modification with nitric acid on the mechanical and tribological properties of carbon fiber‐reinforced thermoplastic polyimide composite

Polyacrylamideacrylate (PAN)‐based carbon fibers were submitted to nitric acid oxidation treatments to improve the interfacial adhesion of the carbon fiber (CF)‐reinforced polyimide (CF/PI) composite. The carbon fiber surfaces were characterized by X‐ray photoelectron spectroscopy (XPS). Nitric acid oxidation not only affects the oxygen concentration but also produces an appreciable change in the nature of the chemical functions, namely the conversion of hydroxy‐type oxygen into carboxyl functions. Nitric acid oxidation treatment modifies the element constituting the fiber, the nitrogen concentration being about 1.2 times higher at the fiber external surface compared to the untreated one. The mechanical and tribological properties of the polymide (PI) composites reinforced by the carbon fibers treated with nitric acid oxidation were investigated. Results showed that the tensile strength of the CF/PI composites improved remarkably due to nitric acid treatment along with enhancement in friction and wear performance. Copyright © 2009 John Wiley & Sons, Ltd.     

Selection of natural fibers based brake friction composites using hybrid ELECTRE-entropy optimization technique

Selecting the best brake friction composite composition amongst a set of natural fibres reinforced composites using hybrid optimization method - ELECTRE (elimination and choice translating priority) II - entropy is discussed in this article. Three sets of natural fibres containing different amounts of banana, hemp, and pineapple reinforced brake friction composites were tested according to IS 2742 (part-4) regulations on a chase friction testing machine. The experimental results have been discussed in terms of seven performance defining attributes such as coefficient of friction, fade, wear, friction stability coefficient, friction recovery, friction fluctuations, and friction variability coefficient. The composite containing 5 wt% pineapple fiber exhibit the highest coefficient of friction, whereas wear performance and friction stability remain highest for 5 wt% hemp fiber based composites. The recovery performance remains highest for the composite containing 15 wt% banana fiber, while fade, friction variability, and fluctuations remain lowest for 10 wt% banana fiber reinforced composites. The tribological results indicate that the inclusion of disparate natural fibers in varying amounts may differently affect the tribological performances and therefore to choose the best brake friction composite satisfying the maximum beneficial criteria hybrid ELECTRE II- entropy optimization technique is used. Brake friction composite containing ~10 wt% banana fibers was ranked first, in meeting the desired performance tribological properties. A comparison of this optimization approach with other multi-criteria decision-making techniques is also made for validating the performance ranking of these composites.     

Study on the evaluation of mechanical and thermal properties of natural sisal fiber/general polymer composites reinforced with nanoclay

Composite materials, made by replacing traditional materials, are used because of their capability to produce tailor-made, desirable properties such as high tensile strength, low thermal expansion, and high strength to weight ratio. The need for the development of new materials is essential and growing day by day. The natural sisal/general polymer (GP) reinforced with nanoclay composites has become more attractive due to its high specific strength, light weight, and biodegradability. In this study, sisal–nanoclay composite is developed and its mechanical properties such as tensile strength, flexural strength, and impact strength are evaluated. The interfacial properties, internal cracks, and internal structure of the fractured surface are evaluated using scanning electron microscope. The thermal disintegration of composites are evaluated by thermogravimetric analysis. The results indicate that the incorporation of nanoclay in sisal fiber/GP can improve its properties and can be used as a substitute material for glass fiber-reinforced polymer composites.     

A novel adaptive neuro-fuzzy inference system model to predict the intrinsic mechanical properties of various cellulosic fibers for better green composites

In this work a novel adaptive neuro-fuzzy inference system model has been developed for the prediction of the intrinsic mechanical properties of various cellulosic natural fibers to enhance their selection for better green composite materials. The model combined modeling function of the fuzzy inference system with the learning capability of the artificial neural network. The developed model was built up based on experimental mechanical properties of various cellulosic fiber types commonly used for natural fiber reinforced composites, and the rules have been generated directly from the experimental data. The developed model was capable of predicting all of Young's modulus, ultimate tensile strength, and elongation at break properties from only two intrinsic properties of fibers namely; cellulose and moisture content. The adaptive neural fuzzy inference system (ANFIS) structure included five layers to realize the establishment and calculation of each model. The system architecture included the fuzzy input layer, product layer, normalized layer, de-fuzzy layer and total output layer. Results have been revealed that the model’s predictions were highly in agreement with other experimentally gained properties when compared with experimental results for verifying the approach. The accuracy of the developed model would enhance predicting other cellulosic fiber properties to develop better natural fiber composites in the near future.

     

仿生矿化增强材料

近年来,随着材料科学领域的发展,机械性能优异且具有特定功能的有机-无机复合材料成为了研究热点。而天然的生物矿化过程产生了在自然界中分布广泛、结构特征多样性、机械性能优异的天然生物矿物,比如牙齿、骨骼、珍珠、贝壳、海胆刺、海洋红虫颚等。这些天然复合增强材料中的矿化组织结构特点和矿化机理为仿生设计与合成具有特定结构、特定功能和优异机械性能的材料提供了理论依据。通过模拟天然过程的仿生矿化方法,利用有机基质调控无机矿物成核生长为固态矿物,最终能够定向组装具有特定有序结构和先进功能的有机-无机复合材料。本文主要综述了自然界中通过生物矿化过程得到的高强度、高韧性的天然复合增强材料,以及受生物矿化增强现象的启发,在化学与材料仿生矿化合成中出现的一些有机-无机复合的增强材料。     

Sisal chemically modified with lignins: Correlation between fibers and phenolic composites properties

Sisal fibers have been chemically modified by reaction with lignins, extracted from sugarcane bagasse and Pinus-type wood and then hydroxymethylated, to increase adhesion in resol-type phenolic thermoset matrices. Inverse gas chromatography (IGC) results showed that acidic sites predominate for unmodified/modified sisal fibers and for phenolic thermoset, indicating that the phenolic matrix has properties that favor the interaction with sisal fibers. The IGC results also showed that the phenolic thermoset has a dispersive component closer to those of the modified fibers suggesting that thermoset interactions with the less polar modified fibers are favored. Surface SEM images of the modified fibers showed that the fiber bundle deaggregation increased after the treatment, making the interfibrillar structure less dense in comparison with that of unmodified fibers, which increased the contact area and encouraged microbial biodegradation in simulated soil. Water diffusion was observed to be faster for composites reinforced with modified fibers, since the phenolic resin penetrated better into modified fibers, thereby blocking water passage through their channels. Overall, composites' properties showed that modified fibers promote a significant reduction in the hydrophilic character, and consequently of the reinforced composite without a major effect on impact strength and with increased storage modulus.     

The effect of grass fiber filler on curing characteristics and mechanical properties of natural rubber

Natural rubber is reinforced with a novel type of grass fiber (Cyperus Tegetum Rox b). The effects of fiber loading of different mesh sizes on curing characteristics and mechanical properties of grass fiber filled natural rubber composite are studied. Since 400 mesh grass fiber loaded natural rubber composite shows superior mechanical properties, therefore the effect of silane coupling agent was studied for this particular composite. Here composites were prepared by using water leached grass fiber. Optimum cure time increases with the increase in fiber loading but the change in scorch time is less. The same trend of increase in optimum cure time is observed in the presence of Si69. But the value is higher compared to that of rubber composite without Si69. With increase in the fiber loading, modulus and hardness of the composite increases but tensile strength decreases. The mechanical properties of the composite, namely moduli at 200 and 300% elongation and hardness increase in the presence of Si69 but tensile strength is less compared to that of the composite without Si69. Elongation at break is not much affected due to the presence of Si69. Copyright © 2004 John Wiley & Sons, Ltd.     

Preparation of starch-based biocomposites reinforced with mercerized lignocellulosic fibers: Evaluation of their thermal,morphological, mechanical,and biodegradable properties

In the present paper, starch-based biocomposites have been prepared by reinforcing corn starch matrix with mercerized Abelmoschus esculentus lignocellulosic fibers. The effect of fiber content on mechanical properties of composite was investigated and found that tensile strength, compressive strength, and flexural strength at optimum fiber content were 69.1%, 93.7% and 105.1% increased to that of cross-linked corn starch matrix, respectively. The corn starch matrix and its composites were characterized by Fourier transform infrared spectroscopy (FT-IR), Scanning electron microscopy (SEM), X-ray diffraction (XRD) and thermogravimetric (TGA) analysis. The fiber reinforced composites were found to be highly thermal stable as compared to natural corn starch and cross-linked corn starch matrix. Further, water uptake and biodegradation studies of matrix and composites have also been studied.     

Mechanical property evaluation of glass–jute fiber reinforced polymer composites

The natural fibers such as jute, coir, hemp, sisal etc. are randomly used as reinforcements for composite materials because of its various advantages such as low cost, low densities, low energy consumption over conventional fibers. In addition, they are renewable as well as biodegradable, and indeed wide varieties of fibers are locally available. In this study, glass–jute fiber reinforced polymer composite is fabricated, and the mechanical properties such as tensile, flexural and impact behavior are investigated. The materials selected for the studies were jute fiber and glass fiber as the reinforcement and epoxy resin as the matrix. The hand lay‐out technique was used to fabricate these composites. Fractured surface were comprehensively examined in scanning electron microscope (SEM) to determine the microscopic fracture mode. A numerical procedure based on the finite element method was then applied to evaluate the overall behavior of this composite using the experimentally applied load. Results showed that by incorporating the optimum amount of jute fibers, the overall strength of glass fiber reinforced composite can be increased and cost saving of more than 30% can be achieved. It can thus be inferred that jute fiber can be a very potential candidate in making of composites, especially for partial replacement of high‐cost glass fibers for low load bearing applications. Copyright © 2016 John Wiley & Sons, Ltd.     

Effect of fiber surface treatments on the essential work of fracture of HDPE-continuous henequen fiber-reinforced composites

Lignocellulosic fibers, such as henequen, sisal, coconut fiber (coir), jute, palm and bamboo, have been used as reinforcement materials for different thermosetting and thermoplastic resins because of their attractive physical and mechanical properties. Unlike the traditional engineering fibers, e.g. glass and carbon fibers, and mineral fillers, these lignocellulosic fibers are able to impart certain benefits such as low density, less machine wear, no health hazards, and a high degree of flexibility to the composite. The last attribute is especially true because these lignocellulosic fibers will bend rather than fracture, like glass fibers do, during processing of the composite. The mechanical properties and fracture behavior of a natural fiber reinforced polymer composite depend, not only on the properties of constituents, but also on the properties of the region surrounding the fiber, known as the interphase, where the stress transfer takes place. Moreover, the tailoring of the interphase by means of surface treatments, and carefully characterizing it, gives a better understanding of the performance of natural-fiber reinforced composites. The fracture toughness resulting from the use of natural fibers as reinforcing materials is quite different between ductile and brittle polymers, as well as between quasi-static and impact loading rates. The aim of this paper is to study the effect of the interphase properties, resulting from well controlled surface treatment of the natural fibers, on the behavior of a ductile polymer matrix composite under quasi-static loading using the essential work of fracture criteria. Specifically, the contribution of each of the different fiber-matrix interfacial adhesion levels towards the dissipation energy were analyzed and discussed. In the case of the plastic work βw_p, there seems to be a synergy between the frictional and chemical interactions observed for both, low and high strain rates. The nonlinear mechanical behavior of the natural fiber under combined tensile-shear loads has also an effect on the fracture behavior of the composite. Additionally, different fiber surface treatments change the microstructural nature of the natural fiber, further affecting its behavior, particularly under high loading rates.     

Advanced polymeric composites via commingling for critical engineering applications

The commingled technology is one of the most effective and alternative methodologies for producing more sustainable as well as uniformly distributed natural fiber reinforced composite without inflecting the shearing strength on yarns or reinforcing natural fiber. The term commingled encompasses the materials consisting of both polymer matrix and reinforcing materials over the same fabric cross-section used for the production of highly flexible, continuous fiber-reinforced thermoplastic prepregs. Nonetheless, the increased pathlength and high melt viscosity around 500–5000 Pa s of the molten thermoplastic makes the processing more difficult compared with other thermoset plastic (usually 100 Pa s). Where the commingled hybrid yarns can be considered as one of the promising preforms employed for long fiber reinforced composite because of low cost, ease of storage and manipulation, excellent flexibility, molding capacity, reduced pressure consolidation as well as impregnation time while processing and the ability to form complex-shaped reinforced composite parts. The parameters that affect the process of commingling controls the consolidation of hybrid yarns thermoplastic composite; the degree of commingling depends on the pressure, temperature, and production speed during a fixed period. Recently commingled thermoplastic composite has become one of the possible destines for a wide array of applications in aircrafts, automotive, and sporting goods. This paper reviews types of commingled plastic composite, various processing routes, and the influence of the processing parameters, their properties, and their application. The manufacturing and development of hybrid yarns through air-jet texturing, intermingling process, are also discussed concerning the attributes of advanced composites.     

Mechanical Properties,Water Absorption,and Chemical Resistance of Napier Grass Fiber Strand–Reinforced Epoxy Resin Composites

Napier grass fiber strands were used as reinforcement to obtain composites with epoxy resin as matrix. To improve the surface, these fiber strands were treated with alkali solution. The composites were prepared by means of hand lay-up molding, then the effects of Napier grass fiber strand loading on mechanical properties such as tensile, flexural and impact, interfacial bonding, and chemical resistance were investigated. The composite with 20 wt.% Napier grass fiber strands gives excellent mechanical properties and chemical resistance, showing that it has the best bonding and adhesion of the composites. SEM micrographs of fractured and worn surfaces clearly demonstrate the interfacial adhesion between fiber and matrix. Alkali-treated Napier grass fiber strand–reinforced composites have better resistance to water and chemicals than the untreated fiber strand composites.     

Novel preparation of glass fiber reinforced polytetrafluoroethylene composites for application as structural materials

A novel method was developed to fabricate continuous glass fiber reinforced polytetrafluoroethylene (PTFE/GF) composites which includes the use of conventional sintering and vacuum assisted resin transfer molding (VARTM), successively. The RTM resin (coded as M4506‐1) “fills” the porosity and defects of original PTFE/GF composites prepared by traditional sintering processing, improves the overall interface bonding between the matrix and fibers, and thus significantly improves the mechanical properties such as the flexural and interlaminar shear strength of fiber reinforced PTFE composites. The present work suggests a new way to produce fiber (especially continuous fiber) reinforced PTFE composites with high mechanical properties, and thus make it potentially possible to use PTFE‐based composites as structural materials. Copyright © 2008 John Wiley & Sons, Ltd.     

Surface modification of ultrahigh‐molecular‐weight polyethylene fibers

To prevent the loss of fiber strength, ultrahigh‐molecular‐weight polyethylene (UHMWPE) fibers were treated with an ultraviolet radiation technique combined with a corona‐discharge treatment. The physical and chemical changes in the fiber surface were examined with scanning electron microscopy and Fourier transform infrared/attenuated total reflectance. The gel contents of the fibers were measured by a standard device. The mechanical properties of the treated fibers and the interfacial adhesion properties of UHMWPE‐fiber‐reinforced vinyl ester resin composites were investigated with tensile testing. After 20 min or so of ultraviolet radiation based on 6‐kW corona treatment, the T‐peel strength of the treated UHMWPE‐fiber composite was one to two times greater than that of the as‐received UHMWPE‐fiber composite, whereas the tensile strength of the treated UHMWPE fibers was still up to 3.5 GPa. The integrated mechanical properties of the treated UHMWPE fibers were also optimum. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 463–472, 2004     

The oxidation‐treated interface on tribological properties of carbon fibers‐reinforced PTFE composite under oil‐lubricated condition

The effect of air oxidation and ozone surface treatment of carbon fibers (CF) on tribological properties of CF reinforced polytetrafluoroethylene (PTFE) composites under oil‐lubricated condition was investigated. Experimental results revealed that ozone treated CF reinforced PTFE (CF–PTFE) composite had the lowest friction coefficient and wear under various applied loads and sliding speeds compared with untreated and air‐oxidated composites. X‐ray photoelectron spectroscopy (XPS) study of carbon fiber surface showed that, after ozone treatment, oxygen concentration was obviously increased, and the amount of oxygen‐containing groups on CF surfaces was largely increased. The increase in the amount of oxygen‐containing groups enhanced interfacial adhesion between CF and PTFE matrix. With strong interfacial adhesion of the composite, stress could be effectively transmitted to carbon fibers; carbon fibers were strongly bonded with PTFE matrix and large scale rubbing‐off of PTFE was prevented, therefore, the tribological properties of the composite were improved. Copyright © 2009 John Wiley & Sons, Ltd.     

Seawater ageing of flax/poly(lactic acid) biocomposites

Natural fibre reinforced biopolymer composites, or biocomposites, are an alternative to the glass fibre reinforced thermoset composites widely used today in marine applications. Biocomposites offer good mechanical properties and total biodegradability, but if they are to be adopted for marine structures their durability in a seawater environment must be demonstrated. In the present study unreinforced PLLA (Poly(l-Lactic acid)), injected and film stacked flax composites with the same PLLA matrix have been examined. All the samples were aged in natural seawater at different temperatures in order to accelerate hygrothermal ageing. Changes to physico-chemical and mechanical behaviour have been followed by weight measurements, thermal and gel permeation chromatography (GPC) analyses, and tensile testing, completed by acoustic emission recording and scanning electron microscopy (SEM) examination. The matrix tensile stiffness is hardly affected by seawater at temperatures to 40 °C but the composite loses stiffness and strength. Fibre/matrix interface weakening is the main damage mechanism induced by wet ageing, but both matrix and fibre cracks also appear at longer periods.     

碳纳米管及碳纤维增强环氧树脂复合材料研究进展

碳纳米管与碳纤维具有优异的力学、电学等性能,广泛用做复合材料增强体,但目前碳纳米管/碳纤维/环氧树脂复合材料的研究具有一定的局限性,只考虑了两相材料间的作用,即仅对单一相进行处理而忽略了另一相的改性。本文从碳纳米管/碳纤维协同增强环氧树脂基体复合材料的思路入手,结合自己的研究成果,综述了国内外相关研究进展。从研究结果可以看出,将三相材料之间完全有效地联系起来,发挥三者间的协同效应,复合材料的性能可以发生质的飞跃。