Structure and properties of composites of highly crystalline cellulose with polypropylene: Effects of polypropylene molecular weight

Composite of highly crystalline fibrous cellulose (CE) and polypropylene (PP) of different molecular weights () was prepared via melting-mixing, maleic anhydride grafted polypropylene (MAPP) was used as a compatibilizer. And the effects of molecular weight of PP on the properties of the composites were investigated. Through the studying of mechanical properties, dynamic mechanical properties, melting and crystallization behaviors, thermo-oxidative properties, water absorption behaviors, and the morphology of the composites, it was found that PP with higher molecular weight revealed stronger interfacial interaction with cellulose in the composites. Compared with the lower molecular weight, the composites derived from higher molecular weight of PP exhibited stronger tensile strength at the same cellulose content.     

Multiple melting behavior of isotactic polypropylene and poly(propylene-co-ethylene) after stepwise isothermal crystallization

The multiple melting behavior of several commercial resins of isotactic polypropylene (iPP) and random copolymer, poly(propylene-co-ethylene) (PPE), after stepwise isothermal crystallization (SIC) were studied by differential scanning calorimeter and wide-angle X-ray diffraction (WAXD). For iPP samples, three typical melting endotherms appeared after SIC process when heating rate was lower than 10 °C/min. The WAXD experiments proved that only α-form crystal was formed during SIC process and no transition from α1- to α2-form occurred during heating process. Heating rate dependence for each endotherm was discussed and it was concluded that there were only two major crystals with different thermal stability. For the PPE sample, more melting endotherms appeared after stepwise isothermal crystallization. The introduction of ethylene comonomer in isotactic propylene backbone further decreased the regularity of molecular chain, and the short isotactic propylene sequences could crystallize into γ-form crystal having a low melting temperature whereas the long sequences crystallized into α-form crystal having high melting temperature.     

Structure and properties of nanocomposites with a poly(trimethylene terephthalate) matrix

Poly(trimethylene terephthalate) (PTT), and three organically modified montmorillonites were mixed in the melt state obtaining widely dispersed nanocomposites. The parameters varied in this study were the type and amount of the organic modification and the clay content. A higher polarity of the surfactant made intercalation easier, but neither the nature (included polarity) nor the amount of surfactant influenced the dispersion level. The latter was shown directly by TEM and indirectly by the values of the modulus of elasticity. Upon mixing, a maximum interlayer distance was observed regardless of the initial interlayer distance and the nature and amount of the organoclay used. This finding was also observed in other matrices but does not appear to be a general rule. The decrease in the break properties is mainly attributed to the clay addition and the increases in the modulus of elasticity were large, in agreement with the high degree of dispersion obtained.     

Preparation and characterization of polypropylene/waste tyre dust blends with addition of DCP and HVA-2 (PP/WTDP-HVA2)

Preparation of polypropylene (PP)/waste tyre dust (WTD) blends with addition of dicumyl peroxide (DCP) and N,N′-m-phenylenebismaleimide (HVA-2) (PP/WTD_P-HVA2) was described. The blends were characterized based on their tensile properties, swelling resistance and morphology, as well as thermal properties. The results reveal that the presence of both chemicals in PP/WTD_P-HVA2 blends brought about noticeable improvements in tensile properties, swelling resistance and interfacial adhesion. The thermal stability was also improved, indicating existence of some chemical interaction between WTD and the PP matrix in the presence of both DCP and HVA-2 during processing. The results imply that both chemicals had great influences on WTD destabilization, leading to the enlargement and intensification of the copolymer formation and, hence, improved the interfacial adhesion between WTD and the PP matrix. A competing reaction mechanism that may contribute to the property enhancement of PP/WTD_P-HVA2 blends was proposed.     

Synthesis of poly(o‐phenylenediamine) nanofiber with novel structure and properties

The poly(o‐phenylenediamine) (PoPD) was synthesized from the monomer o‐phenylenediamine in various organic solvent medium viz. dimethyl sulfoxide (DMSO), N,N‐dimethyl formamide (DMF) and methanol using ammonium per sulfate as a radical initiator. The structure just like polyaniline derivative with free ?NH functional groups of the synthesized polymers confirmed by various standard characterizations was explained from the proposed polymerization mechanism. All the synthesized polymers were completely soluble in common organic solvent like DMSO and DMF because of the presence of polar free ?NH functional groups in its structure. The formation of polymer nanofiber by reverse salting‐out process was confirmed, and the synthesized polymer in DMSO medium was the best polymer in terms of nano‐morphology as well as conducting properties. Interestingly, the average DC conductivity of undoped polymer film was recorded as 2.21 × 10^?6 Scm^?1 because of induced doping through self charge separation. Moreover, the conductivity of the polymer film was further increased to 1.16 × 10^?3 Scm^?1 after doping by sulfuric acid. Copyright © 2016 John Wiley & Sons, Ltd.     

Analytical protocol to study the food safety of (multiple-)recycled high-density polyethylene (HDPE) and polypropylene (PP) crates: Influence of recycling on the migration and formation of degradation products

An analytical protocol was set up and successfully applied to study the food safety of recycled HDPE and PP crates. A worst-case scenario was applied that focused not only on overall migration and specific migration of accepted starting materials but also on migratable degradation products of polymers and additives that may be formed during mechanical recycling.The analytical protocol was set up to cover a wide variety of possible migrants. Identification and semi-quantification were possible for almost all migrants that increased significantly with increasing mechanical recycling steps for both the HDPE and PP crates.It was concluded that the analytical protocol was suitable to study the influence of (multiple) recycling on the food safety of plastic materials. The protocol can be applied to other plastic food contact materials and provides valuable information on the food safety of the recycling process and the resulting recycled food contact materials in addition to challenge testing.     

Fabrication and electrochemical instrumentation of redox‐active nanofiber mat for polyaniline incorporated with poly(imide sulfonate)

In this study, we demonstrate the fabrication of an electrochemically active nanofiber mat that is a composite of high‐performance poly(imide sulfonate) (PIS) and polyaniline (PANI). First, a nonconductive nanofiber mat comprising nanofibers having diameters of ca. 300 nm was fabricated by the electrospinning of ionomeric PIS in N,N‐dimethylformamide (DMF). Then, the nanofibers were modified using PANI, which was synthesized by the oxidative polymerization of aniline, yielding an electrochemically active nanofiber mat having a diameter of ca. 350 nm. It was confirmed that PANI was successfully incorporated onto the PIS nanofiber mats by X‐ray photoelectron spectroscopy. Subsequently, we conducted electrochemical measurements of the PANI‐modified nanofiber mats using a tailor‐made attachment in which the working electrode gently comes in contact with the nanofiber mat surface. This attachment was observed to be widely useful in the cyclic voltammetry measurements related to redox‐active nanofibers. These observations are expected to contribute to the advancements in application development of the electrochemically active nanofiber mats.     

Mechanical and fracture behavior of polypropylene/poly(ethylene-co-vinyl alcohol) blends compatibilized with ionomer Na

In this work the deformation and fracture behavior of PP/EVOH blends compatibilized with ionomer Na⁺ at room and low temperature was studied. Uniaxial tensile tests on dumb-bell samples and fracture tests on single-edge notched bending (SENB) specimens were performed for 10 wt.% and 20 wt.% EVOH blends with different ionomer content at 23 °C and −20 °C. The incorporation of EVOH to PP led to less ductile materials in tension as judged by the lower values of the ultimate tensile strain displayed by all PP/EVOH blends in comparison to neat PP. In contrast, the ionomer Na⁺ addition partially counteracted this effect. The compatibilizing effect of ionomer Na⁺ was also evident in fracture results since higher values of the fracture parameter were obtained for the ternary blends. SEM observations also confirmed this effect. On the other hand, PP/EVOH blends exhibited different fracture behavior with test temperature. All blends showed “pseudo stable” behavior at room temperature characterized by apparently stable crack growth that could not be externally controlled. On the contrary, blends behaved as semi-brittle at −20 °C with some amount of stable crack growth preceding unstable brittle fracture. Finally, irrespectively of the temperature or the ionomer content all PP/EVOH blends exhibited more ductile fracture behavior with a higher tendency to stable crack propagation than neat polypropylene.     

Synergistic Effect of Phosphite with FuUerene C60 and Fullerenol C60（OH）24 as Antioxidants in Polypropylene

Polypropylene samples with fullerene C60, fullerenol C60（OH）24, 1010, C60/168, C60-OH/168 and 1010/168 as antioxidants were prepared by extrusions. MFR, YI, TGA and OIT of all the samples were tested. According to the results of MFR, during the melt extrusion, fullerene showed excellent stability effect on PP. The antioxidative ability of fullerene was comparable to the traditional antioxidant 1010. The antioxidative ability of fullerenol was not significant in the first extrusion and it accelerated the degradation of PP in the second and the third extrusions. TGA and OIT tests showed that the stability effects of fullerene and fullerenol were slightly lower than antioxidant 1010. In the first time, antioxidant 168 was reported to show great synergistic effects with fullerene and fullerenol as antioxidants, which sussested a simple way to enhance the antioxidative abilities of fullerene and fullerenol.     

Viscosity reduction and disentanglement in ultrahigh molecular weight polyethylene melt: Effect of blending with polypropylene and poly(ethylene glycol)

A significant reduction in melt viscosity of ultrahigh molecular weight polyethylene (UHMWPE) was obtained by blending with polypropylene (PP) and poly(ethylene glycol) (PEG). The mechanism of viscosity reduction was investigated from the view of disentanglement effect. Dynamic mechanical analysis indicated that the pseudoequilibrium modulus (E′) of UHMWPE/PP(80/20) blend in the rubbery plateau was much lower than that of UHMWPE. Accordingly, the calculated entanglement density (ν_e) of UHMWPE/PP (80/20) blend was smaller than that of UHMWPE. Further reduction in E′ and ν_e of the blend was obtained by the incorporation of 1 phr PEG. Slow DSC analysis showed that the high temperature endotherm and exotherm for UHMWPE at slow temperature ramp diminished and increased, respectively when 5 phr PEG was added. It also revealed that the entanglement level of UHMWPE decreased with the addition of a small amount of PEG.     

Enhanced interlayer interaction in cellulose single nanofibre and poly(l-lactic acid) layered films by plasma-initiated surface grafting of poly(acrylic acid) onto poly(l-lactic acid) films

The surface of a poly(l-lactic acid) (PLLA) film was modified with poly(acrylic acid) (PAA) by plasma-initiated polymerization to increase the interaction between PLLA and cellulose single nanofibres (CSNF). The surface wettability of the PAA grafted PLLA film (PLLA-PAA film) was investigated by contact angle measurements. Modification of the PLLA film with PAA decreased the contact angle from 61° to 50°. The surface morphologies of the PLLA film, PLLA-PAA film and CSNF-coated PLLA-PAA film were studied by atomic force microscopy. The interaction between the CSNF and PLLA layers was strengthened by incorporation of a PAA layer onto the PLLA films and it is higher than 2N as proved by a peeling test. This is probably because the carboxyl groups of PAA form hydrogen bonds with the hydroxyl groups of CSNF.     

Automated analysis of terbutaline (BricanylR) in human plasma with liquid chromatography and electrochemical detection using column-switching (multidimensional chromatography)

Summary An automated method based on liquid chromatography has been developed for the determination of terbutaline in human plasma in the range of 5–50 pmole·ml^–1. The necessary sensitivity and selectivity was obtained by using electrochemical detection and a microprocessor-controlled column switching system. A combination of three columns was used: a C₈ type for pre-separation, a C₁₈ type for trapping and, for final separation, a strongly acidic ion exchanger. The accuracy of the method was examined by comparison with a method based on gas chromatography — mass spectrometry. The overall precision was ±3.5% and ±2.2% respectively at 5 and 50 pmole·ml^–1. The total absolute recovery for terbutaline and internal standard at the above concentration levels were in the range 85–106%.Presented at the 14th International Symposium on Chromatography London, September, 1982     

Poly(hydroxyethyl methacrylate)‐based composite cryogel with embedded macroporous cellulose beads for the separation of human serum immunoglobulin and albumin

A novel super‐macroporous monolithic composite cryogel was prepared by embedding macroporous cellulose beads into poly(hydroxyethyl methacrylate) cryogel. The cellulose beads were fabricated by using a microchannel liquid‐flow focusing and cryopolymerization method, while the composite cryogel was prepared by cryogenic radical polymerization of the hydroxyethyl methacrylate monomer with poly(ethylene glycol) diacrylate as cross‐linker together with the cellulose beads. After graft polymerization with (vinylbenzyl)trimethylammonium chloride, the composite cryogel was applied to separate immunoglobulin‐G and albumin from human serum. Immunoglobulin‐G with a mean purity of 83.2% and albumin with a purity of 98% were obtained, indicating the composite cryogel as a promising chromatographic medium in bioseparation for the isolation of important bioactive proteins like immunoglobulins and albumins.     

Poly(lactic acid) nanocomposites with improved flame retardancy and impact strength by combining of phosphinates and organoclay

To minimize the loading level of the char-forming phosphorus based flame retardants in the poly(lactic acid) (PLA) with reduced flammability, we have developed the flame-retarded PLA nanocomposites by melt blending method incorporating organically modified montmorillonite (OMMT) and aluminium diethylphosphinate (AlPi) additives. The influence of AlPi and OMMT on flame retardancy and thermal stability of PLA was thoroughly investigated by means of the limiting oxygen index (LOI), UL94 test, cone calorimeter, X-ray diffraction (XRD), thermogravimetric analysis and scanning electronic microscopy (SEM). The experimental results show that the PLA/AlPi/OMMT system has excellent fire retardancy. The LOI value increases from 19% for pristine PLA to 28% for the flame-retarded PLA. Cone calorimeter analysis of the PLA/AlPi/OMMT exhibits a reduction in the peak heat release rate values by 26.2%. Thermogravimetric analysis and SEM of cone calorimeter residues indicate that OMMT significantly enhances the thermal stability, promotes char-forming and suppresses the melt dripping. The research of this study implies that the combining of the flame retardant and organoclay results in a synergistic effect. In addition, the flame-retarded PLA nanocomposite also exhibits notable increase in the impact strength and the elongation at break.     

Staphylococcus epidermidis adhesion to He, He/O(2) plasma treated PET films and aged materials: contributions of surface free energy and shear rate

Adhesion studies of bacteria (Staphylococcus epidermidis) to plasma modified PET films were conducted in order to determine the role of the surface free energy under static and dynamic conditions. In particular, we investigated the effect of the ageing time on the physicochemical surface properties of helium (He) and 20% of oxygen in helium (He/O₂) plasma treated polyethylene terephthalate (PET) as well as on the bacterial adhesion. Treatment conditions especially known to result in ageing sensitive hydrophilicity (hydrophobic recovery) were intentionally chosen in an effort to obtain the widest possible range of surface energy specimens and also to avoid strong changes in the morphological properties of the surface. Both plasma treatments are shown to significantly reduce bacterial adhesion in comparison to the untreated PET. However, the ageing effect and the subsequent decrease in the surface free energy of the substratum surfaces with time – especially in the case of He treated samples – seem to favor bacterial adhesion and aggregation. The dispersion-polar and the Lifshitz–van der Waals (LW) acid–base (AB) thermodynamic approaches were applied to calculate the Gibbs free energy changes of adhesion (ΔG_adh) of S. epidermidis interacting with the substrates. There was a strong correlation between the thermodynamic predictions and the measured values of bacterial adhesion, when adhesion was performed under static conditions. By decoupling the (ΔG_adh) values into their components, we observed that polar/acid–base interactions dominated the interactions of bacteria with the substrates in aqueous media. However, under flow conditions, the increase in the shear rate restricted the predictability of the thermodynamic models.     

The fabrication and characterization of poly(lactic acid) scaffolds for tissue engineering by improved solid–liquid phase separation

In this article a new technique was developed to fabricate scaffolds with a unique microstructure by solid–liquid separation in combination with particulate-leaching. Firstly, the effects of polymer concentration, quenching temperature on the porous morphology and the mechanical property of obtained scaffolds during solid–liquid separation have been investigated. Then, salt granules as porogen were introduced into the solid–liquid phase separation to produce the unique pore structure of the scaffold. The pore diameter of the scaffold could be controlled with the particulate size and the wall of pores possessed special microstructure, which enhanced the pore interconnectivity. The cell culture results confirmed that a good interconnectivity of the scaffold prepared by the improved solid–liquid separation was useful for nutrition transportation and cell proliferation. Copyright © 2003 John Wiley & Sons, Ltd.     

HPLC determination of Vitamin D(3) and its metabolite in human plasma with on-line sample cleanup

A HPLC method with automated column switching and UV-diode array detection is described for the simultaneous determination of Vitamin D₃ and 25-hydroxyvitamin D₃ (25-OH-D₃) in a sample of human plasma. The system uses a BioTrap precolumn for the on-line sample cleanup. A sample of 1 ml of human plasma was treated with 2 ml of a mixture of ethanol–acetonitrile (2:1 (v/v)). Following centrifugation, the supernatant was evaporated to dryness under a stream of dry and pure nitrogen. The residue was reconstituted in 250 μL of a solution of methanol 5 mmol l⁻¹ phosphate buffer, pH 6.5 (4:1 (v/v)), and a 200 μl aliquot of this solution was injected onto the BioTrap precolumn. After washing during 5 min with a mobile phase constituted by a solution of 6% acetonitrile in 5 mmol l⁻¹ phosphate buffer, pH 6.5 (extraction mobile phase), the retained analytes were then transferred to the analytical column in the backflush mode. The analytical separation was then performed by reverse-phase chromatography in the gradient elution mode with the solvents A and B (Solvent A: acetonitrile–phosphate buffer 5 mmol l⁻¹, pH 6.5; 20:80 (v/v); solvent B: methanol–acetonitrile–tetrahydrofuran, 65:20:15 (v/v)). The compounds of interest were detected at 265 nm. The method was linear in the range 3.0–32.0 ng ml⁻¹ with a limit of quantification of 3.0 ng ml⁻¹. Quantitative recoveries from spiked plasma samples were between 91.0 and 98.0%. In all cases, the coefficient of variation (CV) of the intra-day and inter-day-assay precision was ≤2.80%. The proposed method permitted the simultaneous determination of Vitamin D₃ and 25-OH-D₃ in 16 min, with an adequate precision and sensitivity. However, the overlap of the sample cleanup step with the analysis increases the sampling frequency to five samples h⁻¹. The method was successfully applied for the determination of Vitamin D₃ and 25-OH-D₃ in plasma from 46 female volunteers, ranging from 50 to 94 years old. Vitamin D₃ and 25-OH-D₃ concentrations in plasma were found from 4.30–40.70 ng ml⁻¹ (19.74 ± 9.48 ng ml⁻¹) and 3.1–36.52 ng ml⁻¹ (7.13 ± 7.80 ng ml⁻¹), respectively. These results were in good agreement with data published by other authors.     

In situ polymerization of ethylene with bis(imino)pyridine iron(II) catalysts supported on clay: The synthesis and characterization of polyethylene–clay nanocomposites

Polyethylene–clay nanocomposites were synthesized by in situ polymerization with 2,6‐bis[1‐(2,6‐diisopropylphenylimino)ethyl] pyridine iron(II) dichloride supported on a modified montmorillonite clay pretreated with methylaluminoxane (MAO). The catalysts and the obtained nanocomposites were examined with wide‐angle X‐ray scattering. The exfoliation of the clay was further established by transmission electron microscopy. Upon the treatment of the clay with MAO, there was an increase in the d‐spacing of the clay galleries. No further increase in the d‐spacing of the galleries was observed with the iron catalyst supported on the MAO‐treated clay. The catalyst activity for ethylene polymerization was independent of the Al/Fe ratio. The exfoliation of the clay inside the polymer matrix depended on various parameters, such as the clay content, catalyst content, and Al/Fe ratio. The crystallinity percentage and crystallite size of the nanocomposites were affected by the degree of exfoliation of the clay. Moreover, when ethylene was polymerized with a mixture of the homogeneous iron(II) catalyst and clay, the degree of exfoliation was significantly lower than when the polymerization was performed with a preformed clay‐supported catalyst. This observation suggested that in the supported catalyst, at least some of the active centers resided within the galleries of the clay. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 304–318, 2005     

Gas-phase reactions of SF5, SF2, and SOF with O(3 P): Their significance in plasma processing

Reactions of both SF₅ and SF₂ with O(³ P) and molecular oxygen have been studied at 295 K in a gas flow reactor sampled by a mass spectrometer. For reactions with O(³ P), rate coefficients of (2.0±0.5)×10^–11 cm³ s^–1 and (10.8±2.0)×10^–11 cm³ s^–1 were obtained for SF₅ and SF₂ respectively. The rate coefficients for reactions with O₂ are orders of magnitude lower, with an estimated upper limit of 5×10^–16 cm³ s^–1 for both SF₅ and SF₂. Reaction of SF₂ with O(³ P) leads to the production of SOF which then reacts with O(³ P) with a rate coefficient of (7.9±2.0)×10^–11 cm³ s^–1. Both SO and SO₂ are products in the reaction sequence initiated by reaction between SF₂ and O(³ P). Although considerable uncertainty exists for the heat of formation of SOF, it appears that SO arises only from reaction between SOF and O atoms which is also the source of SO₂. These results are discussed in terms of a reaction scheme proposed earlier to explain processes occurring during the plasma etching of Si in SF₆/O₂ plasmas. A comparison between the results obtained here and those reported earlier for reactions of both CF₃ and CF₂ with O and O₂ shows that there is a marked similarity in the free radical chemistry which occurs in SF₆/O₂ and CF₄/O₂ plasmas.     

2-羰基丙酸(4-吡啶甲酰基)腙与碱土金属配合物的晶体结构及热 稳定性

报道了2-羰基丙酸(4-吡啶甲酰基)腙(H~2L)与碱土金属(Ca,Mg,Sr,Ba)四种配合物的合成,结构及热稳定性。同时,用X射线单晶衍射仪测定了Mg和Ba两种配合物的晶体结构,结构分析表明两种配合物均属单斜晶系,空间群均为P2~1/c。此外,还比较讨论了各配合物不同成键方式所对应的IR特征及热稳定性变化规律。