HPLC determination of pesticides in green bean samples after SPE clean-up

Summary A reversed-phase high performance liquid chromatographic (HPLC) method with an acetonitrile-methanol-water mobile phase gradient and photodiode-array detection (DAD) is described for simultaneous determination of 21 pesticides, frequently used in agriculture, of different types, namely organophosphorus, organochlorine,N-methylcarbamates, triazines and phenylureas in vegetable samples. The pesticides were extracted with acetone and then partitioned from the vegetable sample with dichloromethane. Sample clean-up was accomplished by solid-phase extraction (SPE) using both C₁₈ and florisil SPE columns. Average recoveries from green beans ranged from 70.0 to 110.1%. Detection limits of less than 0.1 mg kg^–1 were obtained.     

Determination of organophosphorus pesticides in aqueous samples by on-line membrane disk extraction and capillary gas chromatography

Summary A fast and simple procedure for the analysis of aqueous samples by on-line membrane disk extraction and capillary gas chromatography (GC) is presented. As an example, organophosphorus pesticides are preconcentrated from aqueous samples on three 0.5 mm thick, 4.2 mm diameter extraction disks. The layers are dried by a stream of nitrogen (10–15 min; ambient temperature). Desorption of the analytes is carried out with ethyl acetate which is directly introduced into a retention gap under partially concurrent solvent evaporation conditions, using an early solvent vapour exit. The final analysis is carried out by GC with thermionic detection. The technique is applied to the determination of a series of organophosphorus pesticides in tap water and water from two European rivers. With a sample volume of only 2.5 ml, detection limits of 10–30 ppt are achieved in tap water and of 50–100 ppt in river water.     

Automated derivatization for on-line solid-phase extraction-gas chromatography; phenolic compounds

An automated system for derivaatization was coupled on-line with solid-phase extraction-gas-chromatography (SPE-GC). The system was optimized for the determination of phenol and chlorinated phenols in aqueous samples. The test analytes were acetylated with acetic anhydride; proper buffering of the sample was a critical factor. Next, the phenol acetates were enriched on a SPE cartridge and transferred to a GC; two appraoaches were studied. In the first approach, the derivatives were enriched on disposable C18 cartridges (ASPEC type) and desorbed with methylacetate. Aan aliquot of the final eluate was injected on-line the GC by means of a loop-type interface. In the second approach, trace enrichment was performed on 10 × 2 mm i.d. LC-type precolumn packed with polystyrenedivinylbenzene copolymer (PLRP-S) this precolumn was dried with a mitrogen purge and the phenol acetates were desorbed with ethyl acetate which was injectedon-line into the retention gap of the GC under partially concurrent solvent evaporation (PCSE) conditions. The Derivatization-SPE-GC system which was based on the loop-type interface has the advantage of simplicity and easy operation, the main drawback is the impossibility to determine phenol acetates which elute prior to trichlorophenol acetates. With the derivatization-SPE-GC approach using PCSE-based desorption, even the most volatile analyte of the test series, phenol acetate, can be determined successfully. The entire procedure, including the derivatization step, was fully automated and integrated in one set-up. The precision data for the integrated on-line derivatization-SP-FID system were fully satisfactory, with RSD values of 1–12 % at the 1 μg/1 level. When a sample volume of 2.2 ml was analyzed, The detection limits for the chlorinated phenol acetates were in the 0.1–0.3 μg/1 range.     

Solid-phase microextraction with micellar desorption and HPLC-fluorescence detection for the analysis of fluoroquinolones residues in water samples

A sensitive and useful method based on solid-phase microextraction with micellar desorption (SPME-MD) coupled to HPLC with fluorescence detection was developed for the determination of five fluoroquinolones (levofloxacin, norfloxacin, ciprofloxacin, enrofloxacin, and sarafloxacin) in environmental water matrices. The SPME extraction efficiency was optimized with regard to time, temperature, pH, and ionic strength using a CW-TPR fiber. A detailed study about the optimum conditions for micellar desorption (surfactant type, concentration, and desorption time) were made. Among different surfactants studied, Polyoxyethylene 10 lauryl ether showed the best responses to extract fluoroquinolones using SPME-MD. Relative standard deviations of the developed method were below 9%. Limits of detection and quantification were between 0.01–0.2 and 0.03–0.6 ng mL⁻¹, respectively. The recoveries achieved for all five compounds were in the 81–116% range. The proposed method was compared using conventional desorbing agent as methanol. Finally, the SPME-MD methodology was applied to the determination of these target analytes in several environmental liquid samples, including seawater, groundwater, and wastewater samples with excellent results.     

Study of solid-phase extraction for the determination of sequestering agents in river water by high-performance liquid chromatography

Anion-exchange solid-phase extraction accompanied with high-performance liquid chromatography has been developed for the determination of six kinds of aminopolycarboxylic acids (APCAs) in river water [N-(2-hydroxyethyl)ethylenediaminetriacetate (HEDTA), ethylenediaminetetraacetate (EDTA), 1,3-propanediaminetetraacetate (PDTA), diethylenetriaminepentaacetate (DTPA), 1,2-propanediaminetetraacetate (MeEDTA), and O,O′-bis(2-aminoethyl)ethyleneglycoltetraacetate (GEDTA)]. The enrichment of APCAs using an anion-exchange cartridge was successfully done by the removal of anions, which competed with APCAs in anion-exchange processes. Barium chloride solution was added to river water and the mixture was passed through On Guard II Ag and H cartridges and then a Bond Elut Jr.SAX cartridge to enrich APCAs. After elution, APCAs were analyzed on two reversed phase C30 columns connected in series and detected with ultraviolet detection. The enrichment using solid-phase extraction permitted the determination of APCAs in river water at concentrations as low as 1 nM. Good recoveries (83–111%) were obtained for each APCA by the standard addition method on three river water samples with high accuracy (RSD 1.8–9.5%). Applying this method, two kinds of APCAs, EDTA and DTPA, were determined in samples from the Oyabe and Senbo Rivers in Japan.     

Preparation and evaluation of a molecularly imprinted sol-gel material for on-line solid-phase extraction coupled with high performance liquid chromatography for the determination of trace pentachlorophenol in water samples

A highly selective imprinted amino-functionalized silica gel sorbent was prepared by combining a surface molecular imprinting technique with a sol-gel process for on-line solid-phase extraction-HPLC determination of trace pentachlorophenol (PCP) in water samples. The PCP-imprinted amino-functionalized silica sorbent was characterized by FT-IR, SEM, nitrogen adsorption and the static adsorption experiments. The imprinted functionalized silica gel sorbent exhibited high selectivity and offered a fast kinetics for the adsorption and desorption of PCP. The prepared sorbent was shown to be promising for on-line solid-phase extraction for HPLC determination of trace levels of PCP in environmental samples. With a sample loading flow rate of 5 ml min(-1) for 2 min, an enhancement factor of 670 and a detection limit (S/N = 3) of 6 ng l(-1) were achieved at a sample throughput of five samples h(-1). The precision (RSD) for nine replicate on-line sorbent extractions of 10 microgl(-1) PCP was 3.8%. The sorbent also offered good linearity (r = 0.9997) for on-line solid-phase extraction of trace levels of PCP. The method was applied to the determination of PCP in local lake water, river water and wastewater samples.     

Evaluation of Polyaniline as a Sorbent for SPE of a Variety of Polar Pesticides from Water Followed by CD-MEKC-DAD

A recently synthesized polyaniline (PANI) has been used and evaluated as a sorbent for solid-phase extraction of a variety of polar pesticides and some of their degradation products from water samples. Several classes of pesticides including phenoxy acids, triazines, ureas, oxime carbamates and carbamates were selected for this study. The determination of these pesticides was carried out using cyclodextrin modified micellar electrokinetic chromatography equipped with diode array detection. The recovery results using PANI were compared with those obtained by C₁₈, Isolute ENV+, Oasis HLB and LiChrolut EN. Effect of humic acid, as a major interference, on extraction recovery was also studied. The performance of the method was evaluated by analysis of tap and river water. The RSD of method was between 6 and 14% (n=3) and detection limits were in the range of 0.01–0.5 g L^–1 using 350-mL water samples.     

Dual injector solvent elution and focussing technique for the on-line analysis of solid-phase extraction cartridges in HPLC

Summary A new dual injector solvent focussing and elution technique developed for high-performance liquid chromatography (HPLC) greatly improves chromatographic efficiency for the on-line analysis of C₁₈ solid-phase extraction (SPE) cartridges. Solutions containing three benzene homologs were used to characterize the dual injector analysis technique and to compare the chromatographic efficiency of this method with conventional SPE analysis methods. Sampling was performed off-line using a glass precolumn cartridge (3 mm i.d. × 30 mm) packed with 15–35 μm C₁₈ silica. On-line cartridge analysis was achieved with two injection valves in either serial or parallel configuration. The injection loop of the first valve contains the eluting solvent, and the cartridge holder is connected in place of the injection loop of the second valve. When an injection is made, both valves are turned to the inject position, and the solvent plug is forced through the cartridge, focussing the analyte at the solvent front as it elutes the cartridge. Solvent focussing at the head of the column, resulting from preconditioning of the column with a small plug of water during injection, further minimizes the variance of the injection plug and improves the chromatographic efficiency. The technique has potential applications to environmental and biological fluid analysis where analyte preconcentration and resolution from the sample matrix components may be difficult with current SPE methods.     

Analysis of some organochlorine pesticides in seafood samples by solid-phase extraction—Gas chromatography

Summary The use of the solid-phase extraction technique for the rapid sample preparation of organochlorine pesticides is described. Samples were simultaneously extracted, cleaned, and fractionated by the solid-phase extraction method and a further separation and determination of extracted fractions was carried out by gas chromatography with either an electron capture or a Hall electrolytic conductivity detector. The percent recovery of the extracted seven pesticides was compared to that of the conventional liquid-liquid extraction method. The analytical figures of merit., chromatograms, and statistic data are reported. The application of this method was demonstrated by a real fish sample determination with mass spectra for confirmation of Kepone detection.     

On-line solid-phase extraction-gas chromatography-ion trap tandem mass spectrometric detection for the nanogram per liter analysis of trace pollutants in aqueous samples

Summary On-line solid-phase extraction-gas chromatographyion-trap tandem mass spectrometry (SPE-GC-MS/MS) has been used for the trace-level determination of polar and apolar pesticides. The SPE-GC interface, an Autoloop 2000, was operated at an injection temperature of 90°C which permitted the determination of thermolabile pesticides such as carbofuran and carbaryl. Rectilinear calibration curves were obtained for the analytes tested over a range of 0.1–500 ng L⁻¹, using a sample volume of 10–100 mL for enrichment on an SPE cartridge packed with styrene-divinylbenzene copolymer. The detection limits for the pesticides were in the 0.01–4 ng L⁻¹ range. For a number of pesticides acceptable tandem mass spectra were obtained at levels as low as 0.1 ng L⁻¹ level in real-life water samples. As a demonstration of the applicability of this technique for inorganic anions, bromide and nitrite were converted into 4-bromoacetanilide and 2-phenylphenol, respectively. The reaction products were pooled and subjected to simultaneous analysis by the present method using full-scan mass spectrometric detection. The detection limits were 0.3 and 2 ng L⁻¹, respectively.     

Triacontyl modified silica gel as a sorbent for the preconcentration of polycyclic aromatic hydrocarbons in aqueous samples prior to gas chromatographic-mass spectrometry determination

<正>Triacontyl modified silica gel as a sorbent coupled with gas chromatography-mass spectrometry(GC-MS) was developed to determine EPA prior 16 polycyclic aromatic hydrocarbons(PAHs) in water samples.Various parameters of solid-phase extraction such as organic modifier solvent,eluent,sample flow rate and volume were optimized.The developed method was found to yield a linear calibration curve in the concentration range of 0.05-8μg/L with respect to naphthalene,acenaphthylene,acenaphthene and 0.01-8μg/L for dibenz[a,h]anthracene and 0.05-14μg/L for fluorene,phenanthrene,anthracene and 0.01-14μg/L for the rest of analytes.Furthermore,the good accuracy and repeatability of the method made sure the requirements for achieving reliable analysis of PAHs in the environmental water samples,and the recoveries of optimal method were in the range of 80-120%except to higher volatility PAHs.C_(30)-bonded silica was proved to be an efficient sorbent for extraction of high molecular weight PAHs.     

Evaluation of expanded graphite as on-line solid-phase extraction sorbent for high performance liquid chromatographic determination of trace levels of DDTs in water samples

Dichlorodiphenyltrichloroethane (DDT) and its metabolites are a typical kind of persistent organic pollutants (POPs). Development of a simple, cost-effective and sensitive methodology to monitor DDTs concentrations in water environment is of particular significance for understanding the fate and behavior of these pollutants. In this paper, a method on the basis of solid-phase extraction (SPE) using expanded graphite (EG) as sorbent coupled on-line with high performance liquid chromatography (HPLC) was developed for the determination of trace levels of p,p′-DDD (2,2-bis(4-chlorophenyl)-1,1-dichloroethane), p,p′-DDT, o,p′-DDT and p,p′-DDE (2,2-bis(4-chlorophenyl)-1,1-dichloroethene) in water. The analytes in water were preconcentrated onto the SPE column packed with expanded graphite, and subsequently eluted with methanol-water (90:10) mixed solvent. HPLC with a photodiode array detector was used for their separation and detection. The developed on-line solid-phase extraction protocol for HPLC permits the current HPLC separation and the next preconcentration proceeded in parallel, and thus allows one determination within 8 min. The precision (R.S.D.) for 10 replicate injections of a mixture of 1 μg l⁻¹ of each analyte was 3.2-6.2% for the peak area measurement. The detection limits (S/N = 3) for preconcentrating 50 ml of sample solution ranged from 10 to 25 ng l⁻¹ at a sample throughput of 7.5 samples h⁻¹. The enhancement factors were about 700. The method was applied to the determination of trace p,p′-DDD, p,p′-DDT, o,p′-DDT and p,p′-DDE in local lake, river and tap water samples.     

Determination of pesticides in soil samples by solid phase extraction disks

Summary A systematic study comparing the methodology and analytical results obtained in an investigation of seven pesticide residues (Molinate, Atrazine, Carbofuran, Pirimicarb, Prometryn, Malathion and Tetrachlorvinphos) in soil samples is reported. Solid-phase extraction (SPE) using glass columns and 47 mm disks of octyl and octadecyl-bonded silica was used in the pesticide analysis. The best extraction efficiency and clearest extracts are obtained with C₈ disks. The analyses were carried out by capillary gas chromatography with nitrogen and phosphorus detection. Recovery experiments were performed at ppb levels in spiked soil samples. The average recoveries of the compounds were 53–77%. Detection limits are between 5 and 30 ng g^–1 based on 5 g moist soil sample. The method was validated by comparing it with conventional liquid-liquid extraction.     

Determination of carboxylic acids in water by gas chromatography using several detectors after flow preconcentration

A novel analytical method is reported that combines continuous solid-phase extraction and gas chromatography for the determination of 22 carboxylic acids in water. The highly polar and hydrophilic analytes were preferentially sorbed on a mixture of LiChrolut EN-Supelclean ENVI-18 (1:1) sorbent column and eluted with methanol; this extraction process did not require derivatisation. The extract was analysed by gas chromatography coupled to a flame ionisation detector as well as a mass spectrometer with electron impact (EI) or positive chemical ionisation modes. The highest sensitivity was achieved when using MS-EI, with good linearity in calibration curves and low detection limits (2-40ngL(-1)) for 50mL of sample. The entire procedure from raw aqueous sample to a ready-to-inject methanol solution of the acids requires less than 15min. Another benefit of this method is the good accuracy (recoveries between 93 and 102%) and precision (relative standard deviation, 3.4-6.2%), which allows the determination of carboxylic acids in environmental water and in real chlorinated and ozonated drinking water.     

固相萃取-气相色谱-质谱联用法测定水中的硝基苯类有机污染物的分析方法研究

建立了固相萃取、毛细柱气相色谱-质谱、内标标准曲线法使用选择离子(SIM)监测采集数据定量分析水中硝基苯类有机化合物的分析方法.通过对固相萃取柱的选择、固相萃取条件(样品溶液的pH、上样速率、上样体积、洗脱液选择及配比)的优化,得出了最佳实验条件.始漏体积达1.5 L.回收率大于80%.检出限为0.015～0.045 μg/L.RSD在1.1%～5.9%之间.     

Simple methodology coupling microwave-assisted extraction to SPE/GC/MS for the analysis of natural steroids in biological tissues: Application to the monitoring of endogenous steroids in marine mussels Mytilus sp.

A simple analytical procedure for the simultaneous determination of eight endogenous steroids (testosterone, androstenedione, 17β-estradiol, estrone, pregnenolone, progesterone, dihydroandrostenedione, and dihydrotestosterone) in aquatic molluscs by solid-phase extraction (SPE) and gas chromatography/mass spectrometry (GC-MS) has been developed. After a microwave-assisted extraction, samples were further extracted and purified using two successive SPE (EnviChrom-P and NH₂) cartridges. Steroids were derivatized with a mixture of N-methyl-N(trimethylsilyl)trifluoroacetamide (MSTFA)/mercaptoethanol/ammonium iodide (NH₄I) and determined by GC-MS in selective ion monitoring mode. Recoveries were in the range 85-114%, although slightly lower for dihydrotestosterone, and the repeatability of the procedure, expressed as the coefficient of variation, was lower than 16%. The limits of detection determined in digestive glands of mussels were in the range 0.1-0.4 ng g⁻¹ wet weight for all the steroids. The developed procedure was then applied to the monitoring of steroid profiles in the digestive glands of mussels from the Arcachon Bay (France) during two reproductive cycles. In parallel, two physiological parameters (lipid content and the condition index of mussels) were also monitored, as well as the seawater temperature and salinity. Only progesterone and pregnenolone were detected in the digestive glands of mussels, and the seasonal variations of progesterone levels seemed to be related to the spawning periods of Mytilus sp. in the Bay. The current challenge for the determination of natural steroids in aquatic invertebrates is also briefly discussed.     

Improved solvent collection system for a dispersive liquid-liquid microextraction of organochlorine pesticides from water using low-density organic solvent

In this study, the organochlorine pesticides (OCPs) levels in lake and tap water samples were determined by a dispersive liquid-liquid microextraction method using a low-density organic solvent and an improved solvent collection system (DLLME-ISCS). This method used a very small volume of a solvent of low toxicity (11 μL of 1-nonanol and 400 μL of methanol) to extract OCPs from 10 mL water samples prior to the analysis by GC. After centrifugation in the dispersive liquid-liquid microextraction, there was a liquid organic drop floating between the water surface and the glass wall of the centrifuge tube. The liquid organic drop (with some water phase) was transferred into a microtube (3 mm×15 mm) with a syringe. The organic and aqueous phases were separated in the microtube immediately. Then, 1 μL of the organic solvent (which was in the upper portion of liquid in the microtube) was easily collected by a syringe and injected into the GC-ECD system for the analysis. Under optimum conditions, the linear range of this method was 5-5000 ng/L for most of the analytes. The correlation coefficient was higher than 0.997. Enrichment factors ranged from 1309 to 3629. The relative recoveries ranged from 73 to 119% for lake water samples. The LODs of the method ranged from 0.7 to 9.4 ng/L. The precision of the method ranged from 1.0 to 10.8% for lake water.     

Strategies for the microextraction of polar organic contaminants in water samples

In this paper the most recent developments in the microextraction of polar analytes from aqueous environmental samples are critically reviewed. The particularities of different microextraction approaches, mainly solid-phase microextraction (SPME), stir-bar-sorptive extraction (SBSE), and liquid-phase microextraction (LPME), and their suitability for use in combination with chromatographic or electrically driven separation techniques for determination of polar species are discussed. The compatibility of microextraction techniques, especially SPME, with different derivatisation strategies enabling GC determination of polar analytes and improving their extractability is revised. In addition to the use of derivatisation reactions, the possibility of enhancing the yield of solid-phase microextraction methods for polar analytes by using new coatings and/or larger amounts of sorbent is also considered. Finally, attention is also focussed on describing the versatility of LPME in its different possible formats and its ability to improve selectivity in the extraction of polar analytes with acid-base properties by using separation membranes and buffer solutions, instead of organic solvents, as the acceptor solution.     

Determination of Non-Steroidal Anti-Inflammatory Drugs in Natural Waters Using Off-Line and On-Line SPE Followed by LC Coupled with DAD-MS

Two different procedures for simultaneous determination of six NSAIDs (diflunisal, diclofenac, fenoprofen, ibuprofen, naproxen and tolmetin) in environmental waters are described. Final analysis of target compounds is performed by reversed-phase liquid chromatography – diode array detection and mass spectrometry (HPLC-DAD and LC-MS), whereas sample preparation is based on solid-phase extraction (SPE). A variety of sorbents and their respective advantages and disadvantages are discussed. For the off-line SPE of NSAIDs from water samples, a LiChrolut RP-18 was selected out of all investigated sorbents. In case of on-line coupling of SPE with chromatographic system LiChrosphere RP-18 was selected as the best one in terms of recovery of NSAIDs evaluated, RSD and availability. The applicability of the method was also evaluated. Method detection limits were in the range of 0.7−94 ng L⁻¹. Recoveries ranged from 96 to 109% and relative standard deviations were lower than 5%. The procedures were shown to be linear over a wide range of concentration, exhibited satisfactory repeatability and accuracy, and reached limits of detection in the low ng L⁻¹ range. No breakthrough volume was observed neither for off-line SPE (in the studied range of 100, 200, 300, 500, 700, 1000 and 2000 mL of tap water sample) nor for on-line SPE (in the wide range of 10 mL, 20 mL, 30 mL, 50 mL, 70 mL, 100 mL and 200 mL of tap water sample).